PANI/煤基石墨烯宏观体复合材料的制备及其电化学性能

以太西无烟煤为原料,采用催化热处理、改良Hummers氧化等方法,制备煤基氧化石墨烯(CGO),进而以CGO和聚苯胺(PANI)为前驱体,采用水热自组装法,制备得到PANI/石墨烯宏观体复合材料(3D-PCG)。采用FT-IR、XRD、Raman、SEM和TEM等技术,研究了材料的组成、结构和形貌,考察了3D-PCG的电化学性能。结果表明,PANI以纳米棒状形态均匀镶嵌在煤基石墨烯宏观体(3D-CG)的网状结构中;当PANI与CGO质量比为1:2时,3D-PCG的电化学性能优于PANI和3D-CG,其比电容可达663 F·g~(-1)。     

高电活性石墨烯/聚苯胺纳米复合材料的制备和表征

采用了一种简单有效地方法制备了高电活性的石墨烯/聚苯胺复合材料。首先,将苯胺在氧化石墨烯（GO）的水性分散液中氧化聚合,制备了氧化石墨烯/聚苯胺（GO/PANI）,再将GO/PANI与水合肼反应,制得还原-氧化石墨烯/聚苯胺（R（GO/PANI））。利用透射电子显微镜（TEM）,热失重分析（TGA）和循环伏安法（CV）对GO/PANI和R（GO/PANI的形貌,热稳定性和电化学性能进行了分析研究。结果表明,GO表面存PANI,且R（GO/PANI）的热稳定性和电活性都明显高于GO/PANI。     

石墨烯/聚苯胺复合阳极的制备及在MFC中的应用

采用化学氧化还原法制备高纯度石墨烯（GR）,利用电化学修饰法得到石墨烯/聚苯胺（GR/PANI）膜阳极,采用红外光谱（FI-IR）、X射线衍射（XRD）、场发射扫描电镜（FESEM）对所制备复合电极进行了表征,采用循环伏安法（CV）、交流阻抗法（EIS）考察了复合电极的电化学性能。将GR/PANI膜阳极应用于固定床微生物燃料电池（MFC）,考察了电池的产电性能。均匀地附着在石墨烯表面,GR/PANI膜电极具有良好可逆性,其电阻小、导电性良好。GR/PANI膜阳极应用于MFC,最大功率密度和开路电压分别为230.2 mW·m^-2和834.6 mV,比未修饰阳极的最大功率密度和开路电压分别提高了110.6%和34.8%,GR/PANI膜阳极的表观内阻也由未修饰阳极的843.2Ω降低为469.4 Ω,且电池启动时间大大缩短,产电稳定性增强。结果表明,GR/PANI复合物是一种优良的电极材料,GR/PANI膜阳极MFC具有良好的产电性能。     

煤基石墨烯制备及电化学性能研究

以碳化硅冶炼炉同步生产石墨化太西煤为原料,采用改良的Hummers氧化还原法制备了煤基石墨烯,通过FT-IR和XRD对其进行了表征,并利用循环伏安、恒电流充放电等电化学测试方法对其电化学性能进行了测试。结果表明:煤基石墨烯具有良好的电化学性能,在电流密度0.5A·g~(-1)下,充放电1000次后煤基石墨烯电极材料的比电容量为105.5F·g~(-1)。     

煤基石墨烯/炭纳米纤维复合材料的制备及其电化学性能

作为一种高性能新型储能器件,超级电容器具有功率密度高、充电时间短、绿色环保等诸多优点,决定超级电容器性能的关键因素是电极材料的性能。以煤为原料,通过高温热处理、化学氧化及等离子体还原技术制备得到煤基石墨烯;进一步将煤基石墨烯与聚丙烯腈(PAN)通过静电纺丝技术复合制备得到煤基石墨烯/炭纳米纤维(PM-CG)复合材料,以期借助于石墨烯所具备的高导电性、电子迁移率等性能获得具有优良电化学性能的电极材料。采用物理吸附仪、扫描电镜以及透射电镜等仪器对所制备的炭纳米纤维进行了表征,并通过电化学工作站研究了其作为超级电容器电极材料的电化学性能。结果表明,煤基石墨烯成功掺杂到炭纳米纤维中,所制备的PM-CG复合材料在6 mol/L KOH电解液中的比电容值可达225.1 F·g~(-1),是同样条件下纯PAN炭纳米纤维比电容值的2.57倍。     

新型石墨烯/聚苯胺/银基复合材料的制备

通过对石墨烯(GN)制备、结构改性及与聚苯胺(PANI)、银粒子(Ag)的复合,设计了制备GN/PANI/Ag新型电极复合材料的工艺路线。首先利用Hummers氧化还原法将石墨氧化成氧化石墨烯,利用硼氢化钠将氧化石墨烯还原成石墨烯,将石墨烯与聚苯胺、银粒子反应,最后制得了GN/PANI/Ag复合材料。利用扫描电子显微镜(SEM),透射电子显微镜(TEM),热重分析(TG)和电导率测试对GN和GN/PANI/Ag的形貌,热稳定性和电化学性能进行了分析研究。结果表明,聚苯胺类衍生物、石墨烯以及银粒子三相在整个复合材料中共存,材料的复合使体系热稳定性和电化学性能得到提高。     

太西煤基新型功能炭材料的制备及其电化学性能

以宁夏太西煤高温直流电煅炉制备的煤基石墨为原料,利用Hummers氧化法制备了氧化石墨,然后分别采用水热法和高温膨胀法制备了煤基三维石墨烯气凝胶(3D-GA)和煤基膨胀石墨(EG)两种新型功能炭材料,并通过FTIR,XRD和SEM对其进行了表征,利用电化学工作站对其电化学性能进行了测试和比较。结果表明:在电流密度500 mA/g下,3D-GA和EG的比电容分别为206 F/g和214 F/g,相比煤基石墨烯粉体(G)的比电容113 F/g,分别提高了82.3%和89.4%;充放电循环1000圈后,3D-GA和EG的比电容保持率分别为95.1%和101%,3D-GA和EG均表现出良好的循环稳定性。     

石油用石墨烯复合材料的制备与性能研究

以聚丙烯腈(PAN)和聚甲基丙烯酸甲酯(PMMA)为前驱体,并加入煤基氧化石墨烯(CGO),采用静电纺丝技术与热处理相结合的方法制备了石油用煤基石墨烯负载多孔炭纳米纤维复合材料(CG/PCNF),对比分析了复合材料的显微形貌和电化学性能。结果表明,CNF试样在制备过程中已经完成了氮吸附且主要为微孔结构,而PCNF试样和CG/PCNF试样分别为微孔和介孔并存结构;CNF、PCNF和CG/PCNF试样的比表面积从低至高的顺序为CNFPCNF 800CG/PCNF,平均孔径从低至高顺序为CG/PCNFPCNF 800CNF,总孔容和介孔孔容从低至高顺序为CNFCG/PCNFPCNF 800;CNF、PCNF800和CG/PCNF试样都具有优良的电容行为,经过5000次循环充放电后,3组试样的比电容值都在92%以上,且CG/PCNF试样具有最大的比电容值,约为95.46%,CG的加入可以有效提升复合材料的循环稳定性。     

聚苯胺/碳纳米管复合材料的研究进展

综述了聚苯胺（PANI）/碳纳米管（CNT）复合材料的化学氧化法和电化学聚合法等制备方法,详细介绍了国内外关于PANI/CNT复合材料在电容、生物传感、甲醇氧化3方面的研究进展,并对该类复合材料的应用和发展前景进行了展望。     

石墨烯的氧化程度和含量对水性锌粉涂料防腐性能的影响

制备了 3种不同氧化程度的氧化石墨烯,利用氧化石墨烯对水性环氧富锌涂料进行改性。采用盐雾试验、电化学测试、耐冲击性及附着力测试等对改性涂层的性能进行研究,研究发现氧化程度较低的氧化石墨烯改性环氧富锌涂料性能最佳。然后探究了氧化石墨烯含量和锌粉含量对该涂层的耐腐蚀性和力学性能的影响。结果表明：氧化石墨烯（ GO）的添加可以有效延缓钢材的腐蚀,当 GO-1添加量为 0.36%（质量分数,下同）,锌粉含量为 44%时,制备所得的 GO-1/水性环氧富锌涂料的综合性能最佳。当制得的氧化石墨烯的氧化程度较小,含氧基团较少且没有出现羧基时,涂料的耐腐蚀性能得到改进。     

Synthesis of carbon-coated graphene electrodes and their electrochemical performance

In this work, C-graphene composed of core graphene and carbon shells was prepared to obtain a new type of carbon electrode materials. Carbon shells containing nitrogen groups were prepared by coating polyaniline (PANI) onto graphene by in situ polymerization and subsequent carbonization at 850 °C. After carbonization, the C-graphene contained 6.5% nitrogen and showed a 2D plate structure and crystallinity like that of pristine graphene. In addition, the C-graphene exhibited electrochemical performance superior to that of pristine graphene, and the highest specific capacitance (170 F/g) of the C-graphene was obtained at a scan rate of 0.1 A/g, as compared to 138 F/g for pristine graphene. This superior performance was attributed to the synergistic effect of porous carbon layer and the graphene and the pseudocapacitive effect by the nitrogen groups formed on the carbon electrode after carbonization.     

Polyaniline/single-wall carbon nanotube (PANI/SWCNT) composites for high performance supercapacitors

PANI/SWCNT composites were prepared by electrochemical polymerisation of polyaniline onto SWCNTs and their capacitive performance was evaluated by means of cyclic voltammetry and charge-discharge cycling in 1 M H₂SO₄ electrolyte. The PANI/SWCNT composites single electrode showed much higher specific capacitance, specific energy and specific power than pure PANI and SWCNTs. The highest specific capacitance, specific power and specific energy values of 485 F/g, 228 W h/kg and 2250 W/kg were observed for 73 wt.% PANI deposited onto SWCNTs. PANI/SWCNT composites also showed long cyclic stability. Based upon the variations in the surface morphologies and specific capacitance of the composite, a mechanism is proposed to explain enhancement in the capacitive characteristics. The PANI/SWCNT composites have demonstrated the potential as excellent electrode materials for application in high performance supercapacitors.     

A new route to synthesize polyaniline-grafted carboxyl-functionalized graphene composite materials with excellent electrochemical performance

A new route to synthesize polyaniline (PANI)-grafted carboxyl-functionalized graphene (PGCG) composite material is established. In this paper, PGCG is first prepared through a two-step carboxyl-functionalized process. PANI can be grafted and grown on the surface of graphene due to the covalent bonding existing between the carboxyl-functionalized graphene and polyaniline. This method cannot only improve the mechanical performance and adaptive performance of polyaniline effectively, but also reduce the production costs and environmental pollution during the synthetic process. Therefore, a green and industrial synthetic process is achieved. X-ray diffraction (XRD) patterns, X-ray photoelectron spectroscopy (XPS) and Fourier transformed infrared (FTIR) all confirm that composite materials have been prepared successfully. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) indicate that the as-prepared PGCG has regular structure. Thermogravimetric analysis (TGA) indicates that the addition of graphene nanosheets can significantly improve the thermostability of PANI. Moreover, the as-prepared material exhibits superior electrochemical performance. As an electrode material for supercapacitors, PGCG possesses high specific capacitance of 158 F g^?1 at a scan rate of 25 mV s^?1 and 147 F g^?1 at 50 mV s^?1 in 1 M H₂SO₄. The Nyquist plot also confirms that the PGCG has low charge transfer resistance and good capacitive behavior. These great properties make PGCG a novel electrode material with potential applications in high-performance energy storage devices.     

Influence of multi-walled carbon nanotubes on the electrochemical performance of graphene nanocomposites for supercapacitor electrodes

In this work, multi-walled carbon nanotube (MWNT) bonded graphene (M-GR) composites were prepared using the chemical reduction of graphite oxide (GO) and acid treated MWNTs with different ratios. The M-GR/polyaniline (PANI) nanocomposites (M-GR/PANI) were prepared using oxidation polymerization. The effect of the M-GR ratio on the electrochemical performances of the M-GR/PANI was investigated. It was found that the substrate 2D graphene was coated with 1D MWNTs by chemical reduction and the M-GR was further coated with PANI, leading to increased electrical properties by the π–π interaction between the M-GR and PANI. In addition, the electrochemical performances, such as the current density, charge–discharge, and specific capacitance of the M-GR/PANI were higher than those of graphene/PANI and the highest specific capacitance (1118 F/g) of the composites was obtained at a scan rate of 0.1 A/g for the PANI containing a 0.5 M-GR ratio compared to 191 F/g for the graphene/PANI. The dispersion of the MWNTs onto the graphene surface and the ratio of M-GR had a pronounced effect on the electrochemical performance of the PANI-based composites, which was attributed to the highly conductive pathway created by the M-GR incorporated in the PANI-based composites and the synergistic effect between M-GR and PANI.     

High performance nanocomposite electrodes of mesoporous silica platelet‐polyaniline synthesized via impregnation polymerization

A novel high specific capacitance mesoporous polyaniline (PANI)/silica platelet nanocomposite electrode material for supercapacitors was prepared by an impregnation polymerization. The initiator was embedded firstly in the mesoporous silica pores and channels and then initiated the polymerization of aniline (AN). Compared with the other mesoporous silica materials, the mesoporous silica platelets possess a relative shorter mesoporous channels, leading an easier penetration process of initiator and AN to the inner of mesoporous silica platelets. The structures, morphologies, and electrochemical properties of the nanocomposites were thoroughly studied by a series of methods, such as X‐ray diffractometry, scanning electron microscope, nitrogen adsorption‐desorption tests, infrared spectroscopy, thermogravimetric analysis, and electrochemical measurements. The results revealed that the PANI existed both in the inner and surface of the mesoporous silica platelets, leading a continual conductive network and a large specific surface area. These features provide the nanocomposites an excellent electrochemical performance. The biggest specific capacitance is 1,598 F g⁻¹ at a current density of 0.5 A g⁻¹. POLYM. COMPOS., 38:1616–1623, 2017. © 2015 Society of Plastics Engineers     

Graphene/Polyaniline Aerogel with Superelasticity and High Capacitance as Highly Compression-Tolerant Supercapacitor Electrode

Superelastic graphene aerogel with ultra-high compressibility shows promising potential for compression-tolerant supercapacitor electrode. However, its specific capacitance is too low to meet the practical application. Herein, we deposited polyaniline (PANI) into the superelastic graphene aerogel to improve the capacitance while maintaining the superelasticity. Graphene/PANI aerogel with optimized PANI mass content of 63 wt% shows the improved specific capacitance of 713 F g^?1 in the three-electrode system. And the graphene/PANI aerogel presents a high recoverable compressive strain of 90% due to the strong interaction between PANI and graphene. The all-solid-state supercapacitors were assembled to demonstrate the compression-tolerant ability of graphene/PANI electrodes. The gravimetric capacitance of graphene/PANI electrodes reaches 424 F g^?1 and retains 96% even at 90% compressive strain. And a volumetric capacitance of 65.5 F cm^?3 is achieved, which is much higher than that of other compressible composite electrodes. Furthermore, several compressible supercapacitors can be integrated and connected in series to enhance the overall output voltage, suggesting the potential to meet the practical application.     

Recent Advances in Electrochemical Performances of Graphene Composite (Graphene-Polyaniline/Polypyrrole/Activated Carbon/Carbon Nanotube) Electrode Materials for Supercapacitor: A Review

The latest trend in the direction of miniaturized portable electronic devices has brought up necessitate for rechargeable energy sources. Among the various non conventional energy devices, the supercapacitor is the promising candidate for gleaning the energy. Supercapacitor, as a new energy device that colligates the gap between conventional capacitors and batteries, it has attracted more attention due to its high power density and long cycle life. Many researchers work on, synthesizing new electrode material for the development of supercapacitor. The electrode material possesses salient structure and electrochemical properties exhibit the efficient performance of the supercapacitor. Graphene has high carrier mobility, thermal conductivity, elasticity and stiffness and also has a theoretical specific capacitance of 2630 m²g^??1 corresponds to a specific capacitance of 550 Fg^??1. This article summarizes and reviews the electrochemical performance and applications of various graphene composite materials such as graphene/polyaniline, graphene/polypyrrole, graphene/metal oxide, graphene/activated carbon, graphene/carbon nanotube as an electrode materials towards highly efficient supercapacitors and also dealt with symmetric, asymmetric and hybrid nature of the graphene based supercapacitor.     

Influence of the reaction temperature on polyaniline morphology and evaluation of their performance as supercapacitor electrode

The polyaniline (PANI) nanostructures of tubular, spherical, and granules morphologies were synthesized by chemical oxidation approach in different reaction temperatures and used as the active electrode materials of symmetric redox supercapacitors. X‐ray diffraction and scanning electron microscopy techniques are employed for characterization of these PANIs. With the initial and reaction temperature increase, the morphology of PANI turned from block to spherical and tubular. Electrochemical properties of these PANI electrodes are studied by cyclic voltammetry (CV), agalvanostatic charge–discharge test, and electrochemical impedance spectroscopy (EIS) in 1M H₂SO₄ aqueous solution. The highest electrochemical properties are obtained on the PANI with tubular morphology. The initial specific capacitance of tubular, spherical, and granules PANI are about 300, 300, and 290 F g^?1 at a constant current of 5 mA. Meanwhile, the retention of the tubular PANI capacitance after 500 charge–discharge cycles was 75%, whereas the spherical and granules PANI was only 35% and 57%. The results indicate that tubular PANI electrodes have potential applications as high‐performance supercapacitors electrode materials. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3753–3758, 2013     

基于聚苯胺改性构建三维MXene复合材料及其电容性能

通过直接电化学法,本文利用MXene表面官能团的诱导能力,在外加电场的作用下,将苯胺单体与MXene共同修饰在不锈钢电极表面,成功制得具有三维结构的MXene/聚苯胺复合电极材料。采用SEM、XRD、XPS、FTIR和Raman光谱对复合电极材料的表面形貌、物相结构和组成进行了表征,并在1mol/L H₂SO₄中详细研究了该电极材料的电容性能。结果表明,得益于MXene的掺杂,MXene/聚苯胺复合电极表现出较好的电子传导能力和优异的电容性能,在10mV/s的扫描速率下电容可达417F/g,当扫描速率增至200mV/s时,其电容保持率为52%,比纯PANI电极高31%。该复合电极材料具有良好的循环稳定性,在1.0A/g的电流密度下循环2000次后电容保持率可维持在83.4%。此项研究工作可为三维MXene复合材料的构建提供设计思路。     

Fabrication of graphene/single wall carbon nanotubes/polyaniline composite gels as binder-free electrode materials

A three-dimensional (3D) graphene-based hydrogels system containing one-dimensional (1D) carbon material-single wall carbon nanotubes (SWCNTs) and pseudocapacitor material-polyaniline (PANI) was prepared by combination of cross-linking, reduced and in situ polymerization. The polyaniline nanoparticles were combined with the reduced graphene sheet by π-π conjugation. The as-perpared composite gels could be directly used as electrode materials without binders. Due to the synergistic effect between SWCNTs, graphene sheet and PANI, the graphene/single wall carbon nanotubes/polyaniline (GH/SWCNTs/PANI) composite gel shows the enhanced electrochemical performances. The resultant GH/SWCNTs/PANI gel electroactive material shows a gravimetric specific capacitance of 145.4 F/g at 0.5 A/g and has improved 45% compared with initial graphene hydrogel (GH) at the same current density. And it keeps high retention of 98.8% of the initial capacity after 10,00 charge/discharge cycles at high current density of 10 A/g. The great cycle stability achieved is fundamentally attributed to the support of graphene sheet and single wall carbon nanotubes, which favors stress distribution and charge transfer during the longtime charge/discharge process. The graphene-based hydrogels could be a potential applicant for high rate charge/discharge applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 46948.