Morphology of epoxy resin modified with silyl‐crosslinked urethane elastomer

Silyl‐crosslinked urethane elastomer modifying epoxy resin has drawn much interest. Here the triethoxysilyl‐terminated polycaprolactone elastomer (PCL‐TESi) modifying diglycidylether of bisphenol A epoxy resins (DGEBA) system was chosen, and then the effect of the type of curing agent on the phase structure of the studied epoxy resin system was investigated. The modified systems were obtained with different phase structures by varying the formulations of the curing agent. It was experimentally shown that with the addition of aminosilane (KBE‐9103), the crosslinked density was greatly increased. The cured system also showed from SEM and TEM analysis that addition of KBE‐9103 increased the compatibility between the PCL‐TESi and DGEBA, which made the ductility of the system decrease, but also indicated from TEM that addition of much KBE‐9103 made the reacted silicone particles coagulate each other. The state of phase separation from TEM in the cured system was theoretically explained. These would serve the deeper studies of the mechanism of silyl‐crosslinked urethane elastomer modifying epoxy resin in the future. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 611–619, 2005     

Preparation and properties of soybean oil–based curing agents for epoxy resin

In order to improve the flexibility properties of conventional epoxy resin, two novel soybean oil–based curing agents were synthesized. The curing agent obtained from the reaction between epoxy soybean oil and ethylene diamine was named EEDA, and another curing agent derived from epoxy soybean oil and isophorone diamine was named EIPDA. Several techniques were used to systematically investigate the effects of the structure and content of the two curing agents on the properties of the cured products. The Fourier transform infrared analysis demonstrated that epoxy resin reacted with soybean oil–based curing agents. The differential scanning calorimetry analysis showed that the curing process between diglycidyl ether of bisphenol‐A (DGEBA) and soybean oil–based curing agents only had an exothermic peak. Thermogravimetric analysis indicated that the cured DGEBA/EIPDA system was more stable than the DGEBA/EEDA system below 300 °C. Mechanical tests and Shore D hardness tests suggested that excessive EEDA greatly enhanced the toughness of cured products because of the introduction of aliphatic chains.© 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44754.     

Influence of rubber on the curing kinetics of DGEBA epoxy and the effect on the morphology and hardness of the composites

The influence of the end groups of two liquid rubbers on curing kinetics, morphology, and hardness behavior of diglycidyl ether of bisphenol-A based epoxy resin (DGEBA) has been studied. The rubbers are silyl-dihydroxy terminated (PDMS-co-DPS-OH) and silyl-diglycidyl ether terminated (PDMS-DGE). Crosslinking reactions, investigated by shear rheometry, ranged 90–110 °C, using a constant concentration (5 phr) of liquid rubbers and 1,2-Diamino cyclohexane (1,2-DCH) as hardener agent. The gel time, t _gel, of the neat epoxy significantly decreased when adding the elastomers, more so for the silyl-dihydroxy terminated elastomer; at 110 °C the reaction was nearly complete before rheological test started. The results suggest that the elastomers induced a catalytic effect on the curing reaction. Scanning electron microscopy revealed phase separation of the elastomer during the curing reaction with rubber domains about 5 μm size. However, the DGEBA/dihydroxy terminated elastomer composite cured at 110 °C exhibited a homogenous morphology, that is, the rapid reaction time would not allow for phase separation. Water contact angle tests evidenced either more hydrophilic (silyl-diglycidyl ether terminated rubber) or more hydrophobic (silyl-dihydroxy terminated rubber) behavior than the neat epoxy. The latter effect is attributed to the presence of aromatic rings in the backbone structure of PDMS-co-DPS-OH. Microindentation measurements show that the elastomers significantly reduced the hardness of the epoxy resin, the DGEBA/ether terminated composite exhibiting the lowest hardness values. Moreover, hardness increased as reaction temperature did, correlating with a reduction of microdomains size thus enabling the tuning of mechanical properties with reaction temperature.     

Preparation and Application of a New Curing Agent for Epoxy Resin

A new curing agent based on palmitoleic acid methyl ester modified amine (PAMEA) for epoxy resin was synthesized and characterized. Diglycidyl ether of bisphenol A (DGEBA) epoxy resins cured with different content of PAMEA along with diethylenetriamine (DETA) were prepared. The mechanical properties, dynamic mechanical properties, thermal properties, and morphology were investigated. The results indicated that the PAMEA curing agent can improve the impact strength of the cured epoxy resins considerably in comparison with the DETA curing agent, while the modulus and strength of the cured resin can also be improved slightly. When the PAMEA/epoxy resin weight ratio is 30/100, the comprehensive mechanical properties of the cured epoxy resin are optimal; at the same time, the crosslinking density and glass transition temperature of the cured epoxy resin are maximal.     

用DTA研究环氧树脂固化反应动力学

本文用ＤＴＡ和ＦＩＲ研究双酚Ａ二缩水甘油醚型环氧树脂与２－乙基－４－甲基咪唑固化反应动力学,探讨了固化反应的机理。结果表明：此固化反应是分步进行的。第一步是加成反应,第二步是催化聚合反应,由此确定适宜采用分段固化工艺。通过ＤＴＡ曲线推得固化工艺温度,并计算固化反应各步活化能：Ｅ１＝３６８ｋＪ．ｍｏｌ－１,Ｅ２＝５３９ｋＪ．ｍｏｌ－１     

Curing kinetics and properties of epoxy resin-fluorenyl diamine systems

Diglycidyl ether of bisphenol fluorene (DGEBF), 9,9-bis-(4-aminophenyl)-fluorene (BPF) and 9,9-bis-(3-methyl-4-aminophenyl)-fluorene (BMAPF) were synthesized to introduce more aromatic structures into the epoxy systems, and their chemical structures were characterized with FTIR, NMR and MS analyses. The curing kinetics of fluorenyl diamines with different epoxy resins including DGEBF, cycloaliphatic epoxy resin (TDE-85) and diglycidyl ether of bisphenol A (DGEBA) was investigated using non-isothermal differential scanning calorimetry (DSC), and determined by Kissinger, Ozawa and Crane methods. The thermal properties of obtained polymers were evaluated with dynamic mechanical thermal analysis (DMTA) and thermogravimetric analysis (TGA). The results show that the values of activation energy (E_a) are strongly dependent on the structures of epoxy resin and curing agent. The curing reactivity of epoxy system is restrained by the introduction of rigid fluorene into chain backbone and flexible methyl into side groups. The cured DGEBF/fluorenyl diamine systems exhibit remarkably higher glass transition temperature, better thermal stability and lower moisture absorption compared to those of DGEBA/fluorenyl diamine systems, and display approximate heat resistance and much better moisture resistance relative to those of TDE-85/fluorenyl diamine systems.     

Preparation of a light color cardanol-based curing agent and epoxy resin composite: Cure-induced phase separation and its effect on properties

A light color cardanol-based epoxy curing agent (MBCBE) was synthesized from cardanol butyl ether, formaldehyde and diethylenetriamine. In comparison, a phenalkamine with a similar structure was also prepared. The chemical structures were confirmed by GC–MS and FTIR. The cure behaviors of diglycidyl ether of bisphenol A (DGEBA) with these two curing agents was studied by differential scanning calorimetry (DSC). The morphology, mechanical properties, thermal properties of the cured epoxies were also investigated. The DSC results indicated that MBCBE is less reactive than the phenalkamine. The morphology of the cured MBCBE/DGEBA consisted of cavities dispersed within a continuous epoxy matrix. The cavities markedly improved the lap shear strength and impact strength of the cured resin. Both the two cured resins indicated a two-stage decomposition mechanism. Compared with PKA/DGEBA, the weight loss of MBCBE/DGEBA at the first stage was mainly resulted from the dispersed phase in the epoxy matrix.     

Porous epoxy monolith prepared via chemically induced phase separation

Macroporous epoxy monolith was prepared via chemically induced phase separation using diglycidyl ether of bisphenol A (DGEBA) as a monomer, 4,4′-diaminodiphenylmethane (DDM) as a curing agent, and epoxy soybean oil (ESO) as a solvent. The morphology of the cured systems after removal of ESO was examined using scanning electron microscopy, and the composition of epoxy precursors/solvent for phase inversion was determined. The phase-separation mechanism was deduced from the optic microscopic images to be spinodal decomposition. The pore structure of the cured monolith was controlled by a competition between the rates of curing and phase separation. The ESO concentration, content of curing agent, and the curing temperature constituted the influencing factors on the porous morphology. The average pore size increased with increasing ESO concentration, increasing curing temperature, and decreasing the content of curing agent.     

用DTA研究环氧树脂固化反应动力学

本文用DTA和FIR研究双酚A二缩水甘油醚型环氧树脂与2-乙基-4-甲基咪唑固化反应动力学,探讨了固化反应的机理。结果表明,此固化反应是分步进行的。第一步是加成反应,第二步是催化聚合反应,由此确定适宜采用分段固化工艺。通过DTA曲线推得固化工艺温度,并计算固化反应各步活化能：E1＝36．8kJ．mol-1,E2＝53．gkJ·mol-1。     

Curing of epoxy–urethane copolymers in a heated mold: Effect of the curing conditions on the phase‐separation process

The curing process of an epoxy–urethane copolymer in a heated mold was studied. The epoxy resin (DGEBA, Araldyt GY9527; Ciba Geigy), was coreacted with a urethane prepolymer (PU, Desmocap 12; Bayer) through an amine that acted as crosslinking agent (mixture of cycloaliphatic amines; Distraltec). The study focused on the effect of the curing condition and PU concentration on time–temperature profiles measured in the mold and the consequent final morphologies obtained. As the PU concentration increases, the maximum temperature reached in the mold decreases as a result of the dilution effect of the elastomer on reaction heat, whereas the T_g of the piece also decreases. Phase separation is a function of conversion and temperature reached in the curing part and was analyzed using experimental data and a mathematical model that predicts temperature and conversion throughout the thickness of the mold. Scanning electron microscopy and atomic force microscopy were used to determine the characteristics of the dispersed phase for the different formulations and conditions of curing. It was shown that the size of the dispersed phase increased with the initial PU concentration, whereas there were practically no differences in the separated phase as a function of position or temperature of curing (in the range of 70 to 100°C studied). The superposition of the phase diagrams with the conversion–temperature trajectories during cure provided an explanation of the morphologies generated. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 889–900, 2001     

Rubber modified epoxy resin. II: Phase separation behavior

DGEBA (diglycidyl ether of bisphenol A)–ATBN (amine terminated butadiene acrylonitrile copolymer) blends exhibited upper critical solution temperature (UCST) behavior. Triethylene tetramine (TETA) was introduced as an amine curing agent of epoxy. The real-time phase separation behavior of ATBN-added epoxy system during cure was investigated using laser light scattering. SEM (scanning electron microscopy) and optical microscopy were also employed to observe the morphology of the epoxy blends. Since the DGEBA–ATBN blends showed UCST behavior, the degree of phase separation when cured at low temperature was higher than that when cured at high temperature. The domain correlation length increased as the curing temperature was lowered. Dynamic mechanical analysis (DMA) results indicated that the phase inversion occurred above 20 wt% of ATBN composition.     

硅氧烷封端星形有机低聚物/环氧树脂复合材料的性能研究

通过溶胶-凝胶技术,利用合成的硅氧烷封端星形有机低聚物对环氧树脂进行改性,并固化试样。研究了硅氧烷封端星形有机低聚物/环氧树脂复合材料的拉伸强度和耐热性能,并利用SEM分析了拉伸样断面的微观结构。结果表明:硅氧烷封端星形有机低聚物改性环氧树脂固化后,复合材料的拉伸强度、断裂伸长率明显提高。随着偶联剂(KBE-9103 )的加人,试样的拉伸强度、断裂伸长率上升。复合材料中由于引人Si-O-Si网络结构,其热稳定性能也明显提高。     

新型环氧树脂增韧稀释剂的性能研究

采用国产669环氧稀释剂与聚氨酯预聚物反应合成了含有端环氧基聚醚氨酯的环氧树脂增韧稀释剂(U669)。将该化合物与环氧树脂(E51)共混,并分别采用氰乙基化己二胺和593#固化,通过力学性能测试,研究了U669含量对固化物性能的影响,并采用扫描电镜观察了断面微观结构。结果发现:其固化物具有海岛结构;2种固化体系的剪切强度在E51/U669质量比为60/40时达到极值,分别为21.91MPa和16.21MPa;采用593#作固化剂,在E51/U669质量比为80/20时,共混固化物的拉伸强度和弯曲强度达到最大值62.63MPa和97.37MPa;采用氰乙基化己二胺固化的体系的断裂伸长率和冲击性较593#固化体系好,其最大断裂伸长率达120.98%,当U669质量分数大于50%时,固化物具有弹性体的特征。     

Loss of Curing Agent During Thin Film (Droplet) Curing of Thermoset Material

Recently, it has been reported by our group and others^1.2 that loss of curing agent is encountered during the curing of small droplets or thin films of amine cured epoxies. In our earlier study³ results were reported on loss of curing agent in small droplets used in conducting the rnicrobond, single fiber test for determination of interfacial shear strength (ISS). It was reported that use of a volatile curing agent (meta-phenylene diamine (m-PDA) with DGEBA resin) resulted in increasing amounts of curing agent being lost (as measured by T₈ of the cured droplets) with decreasing droplet size during the processing procedure. Droplets smaller than 150 micrometers were seen to lose up to 40% of the curing agent leading to alteration of the mechanical properties of the droplet and, therefore, causing measured values of ISS to be exceedingly low. Use of a less volatile curing agent (Jeffamine 700, a polyether diamine, Texaco Specialty Chemicals) in combination with DGEBA resin produced results which indicated that loss of curing agent was not occuring. This study was undertaken to show the relationships between film (or droplet) size and the amount of curing agent lost (during the processing) for three different aminecured epoxy systems.     

Synthesis and characterization of diphenylsilanediol modified epoxy resin and curing agent

A series of diphenylsilanediol modified epoxy resins and novel curing agents were synthesized. The modified epoxy resins were cured with regular curing agent diethylenetriamine (DETA); the curing agents were applied to cure unmodified diglycidyl ether of bisphenol A epoxy resin (DGEBA). The heat resistance, mechanical property, and toughness of all the curing products were investigated. The results showed that the application of modified resin and newly synthesized curing agents leads to curing products with lower thermal decomposition rate and only slightly decreased glass transition temperature (T_g), as well as improved tensile modulus and tensile strength. In particular, products cured with newly synthesized curing agents showed higher corresponding temperature to the maximum thermal decomposition rate, comparing with products of DGEBA cured by DETA. Scanning electron microscopy micro images proved that a ductile fracture happened on the cross sections of curing products obtained from modified epoxy resins and newly synthesized curing agents, indicating an effective toughening effect of silicon–oxygen bond.     

甲基丙烯酸改性环氧树脂改进环氧胶膜性能研究

甲基丙烯酸(MAA)和环氧树脂(EP)进行反应后,添加偶氮二异丁腈(AIBN)和丙烯酸异辛酯,合成的含有丙烯酸树脂链段的环氧树脂作为增韧剂,制备成环氧胶膜。改性后的环氧树脂胶膜剪切强度及剥离强度明显提高,DSC测试显示体系的耐热性能损失不大,用红外光谱分析了固化过程及其改性过程中的反应情况。结果表明,改性后的EP制备出的树脂固化物具有良好的力学及耐热性能。     

Microstructure and thermal properties of silyl-terminated polycaprolactone–polysiloxane modified epoxy resin composites

With a direct nucleophilic addition between  OH groups of polydiol and  NCO of a silane, a blend of silyl-terminated polycaprolactone PCL-Si and silyl-terminated polydimethylsiloxane PDMS-Si oligomer, PCS-2Si, were firstly prepared, and then blended with a commercial epoxy resin (diglycidyl ether of bisphenol-A, DGEBA) to form a ternary composite. The formed ternary composites of different content of DGEBA were cured using a polyamidoamine as a curing agent and a sol–gel process at ambient temperature. The microstructures and properties of the cured composites were investigated by SEM, TGA, and energy dispersive spectroscopy. The results showed the compatibility between DGEBA and PDMS increased with increasing content of PCS-2Si, but higher content of PCS-2Si resulted in a slight enrichment of silicon in the surface of the cured film. TGA showed that incorporating PCS-2Si into epoxy resin altered the composites' thermal stability and degradation characteristics. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

聚双胍/环氧树脂体系潜伏性固化过程

用己二胺与双氰胺熔融缩聚, 合成了一种新型潜伏性环氧树脂固化剂, 并研究了其与环氧树脂的固化过程。用FTIR、XPS、¹H NMR分析了固化剂的结构;用DSC分析得到了固化剂与环氧树脂的适宜配比、固化体系的适宜固化温度及固化动力学参数;通过XRD分析了固化物的相结构;通过TG分析了固化物的热稳定性。结果表明, 与双氰胺环氧树脂固化体系相比, 固化温度降低近70℃, 同时潜伏性能良好, 30 d内固化度少于10%, 热稳定性能良好, 热分解温度超过300℃。     

Transmission electron microscopy study of room temperature cured PMMA grafted natural rubber toughened epoxy/layered silicate nanocomposite

Abstract

A morphological study was conducted on ternary systems containing epoxy, poly(methyl methacrylate) grafted natural rubber and organic chemically modified montmorillonite (Cloisite 30B), using TEM. The following four materials were prepared at room temperature: cured unmodified epoxy, cured toughened epoxy, cured unmodified epoxy/Cloisite 30B nanocomposites and cured toughened epoxy/Cloisite 30B nanocomposites. Mixing process was performed by mechanical stirring. Poly(etheramine) was used as the curing agent. The detailed TEM images revealed cocontinuous and dispersed spherical rubber in the epoxy–rubber blend, suggesting a new proposed mechanism of phase separation. High magnification TEM analysis showed good interactions between rubber and Cloisite 30B in the ternary system. In addition, it was found that rubber particles could enhance the separation of silicate layers.     

Phase Separation of Poly(ether sulfone imide) Modified Epoxy Resins

Amine terminated poly(ether sulfone imide) (PESI) with various imide and ethersulfone contents but similar polymer molecular weights were blended with diglycidyletherbisphenol-A (DGEBA) and cured with diaminodiphenylsulfone (DDS). The imide group, a tertiary amine, is a catalyst of the curing reaction of DGEBA with DDS, but it is poorly compatible with uncured epoxy resin. The ethersulfone group is not a catalyst of the curing reaction of DGEBA with DDS, but it has a similar chemical structure as DDS and is compatible with epoxy resin while it is at a low degree of curing. Since PESIs used in this study had similar molecular weights, increasing imide content of PESI would reduce ethersulfone content. The influence of imide and ethersulfone contents of PESI on the phase separation and curing reaction of DGEBA/DDS/PESI blend was investigated using differential scanning calorimetry (DSC), time-resolved light scattering (TRLS), and polarized optical microscopy (POM). Though the imide group has a catalysis effect on the curing reaction of DGEBA with DDS, however, its poor compatibility with epoxy resin retards the curing reaction. Our experimental results revealed the morphology of the cured blends and the curing behavior was a compromise result of catalysis and compatibility of PESI with epoxy resin.