Minimal Realization of Linear Graph Models for Multi-physics Systems

An engineering system may consist of several different types of components,belonging to such physical"domains"as mechanical,electrical,fluid,and thermal.It is t...     

Quantum Cooperative Robotics and Autonomy

The intersection of Quantum Technologies and Robotics Autonomy is explored in the present paper.The two areas are brought together in establishing an interdisci...     

考虑进油孔有限长滑动轴承油膜力的近似解析解

针对具有进油孔的有限长滑动轴承油膜力求解问题,采用变分原理和分离变量法,求得了有限长滑动轴承油膜压力分布的近似解析表达式。将油膜压力分布的近似解析表达式在油膜存在区域上进行积分,即得到了油膜力。将提出的计算有限长滑动轴承油膜力方法与无限长轴承模型、有限元方法的计算结果进行了比较,发现了提出的方法与有限元方法的计算结果很接近。最后,研究了进油孔位置和进油压力对油膜存在区域、油膜力等的影响,研究结果表明进油孔位置和进油压力对油膜存在区域和油膜力有较大的影响。     

三绕组变压器的双绕组等效建模及在Matpower中的应用

针对实际电网存在着大量的三绕组变压器,但国际上一些著名商业软件,如BPA仿真软件、Matpower这一权威潮流计算开源软件,均只提供双绕组变压器模型,限制了其在具有三绕组变压器的电力系统中的应用的问题,潮流计算是自主开发的电力系统各种应用软件的核心模块,因此依托国际权威开源程序进行二次开发,是一种较好的选择。对Matpower要求的数据格式进行了归纳,对变压器的一般的等值电路及带理想变压器的等值电路和带标幺值的等值电路进行了分析研究,提出了三绕组变压器转换为双绕组等效模型的建模方法,使得原先只适应双绕组变压器的潮流计算软件可以适用于三绕组变压器电网的潮流计算;最后以Matpower软件为例进行了案例计算,并用PSASP仿真软件进行对比验证。研究结果证明,所提出的建模方法是有效的。     

On the Relation of Load to Average Gap in the Contact Between Surfaces with Longitudinal Roughness

A computer simulation model for the contact between longitudinally-oriented rough surfaces has been formulated. This model closely duplicates the actual surf ace contact deformation behavior by taking into account the elastic interactions between the asperities. There were no assumptions made about the shapes, or any deformation behavior of the asperities, except for their obeying the laws of elasticity. The plastic deformations on the high asperity peaks were taken into account by setting a ceiling on their contact pressures at the material hardness value. The simulations used real surface profiles which were digitized from unworn circumferentially ground steel surfaces. Each pair of these profiles was mathematically combined to form an equivalent rough profile pressing against an infinitely rigid flat and having the appropriately adjusted elastic modulus. A total of 28 different pairs of profiles were used in the simulations. Each contacting pair was subjected to 30 different load levels and the local contact pressures and deformations were calculated. The contact simulations yielded some important mathematical relationships between parameters, such as the real area of contact, average gap, and average asperity load through statistical curve fitting. Two analytical functions were generated to relate the average load to average gap and the real area of contact to load.     

Fifth International Summer School on Screw-Theory Based Methods in Robotics

正3-11 September,2014University of Bologna,Bologna,Italy www.summerscrews.org summerscrews2014.ing.unibo.it SUMMER 20SCREWS 14In 2014,our screw-theory school comes to the world's oldest university.In early September,Summer Screws'14 will gather six experts in the application of screw theory in robotics and up to 40 participants at the University of Bologna,Bologna,Italy.The school will teach attendees how to apply existing methods and empower them to develop new ones in their own research.The basic theoretical notions will be introduced in a rigorous manner,emphasizing examples,applications,and exercises.Scholarships are available.     

电站锅炉模糊风险评价方法研究与应用

针对电站锅炉风险等级评价问题,将模糊综合评价技术应用到电站锅炉风险等级评价中。开展了电站锅炉失效影响因素及模糊评价因素的重要程度分析,建立了一套科学合理适于在线评价的电站锅炉风险评价体系,提出了模糊综合评价技术与改进的模糊层次分析法相结合的模糊风险评价方法,利用改进的模糊层次分析法计算了指标体系中各层指标权重。对某一台电站锅炉的实际运行工况影响子因素进行了模糊风险评价,采用模糊合成算子进行模糊综合运算得到电了站锅炉运行工况影响子因素的评价向量。研究结果表明:电站锅炉的运行工况影响子因素的风险评价等级为第6级,失效可能性等级为小,该电站锅炉运行工况良好。     

INDUSTRIAL ENGINEERING AND VISUALISATION-A PRODUCT DEVELOPMENT PERSPECTIVE

Taking the actual project of teaching and researching process for example, the relationship between the industrial engineering and product development is discussed. And use the novel visualization technology to support the industrial engineering and product development. How to use the new computer modeling and simulating technologies to support the product development and industrial engineering, is introduced especially. The support includes both domestic products and industrial systems. The visualization and computer technologies take a very important role in some system or multi-direction modeling, those technologies mentioned above can help the industrial engineers study the effect of design on the whole life circle, including the producing steps. So the engineers can avoid making the wrong decision which may cause bad effects on the whole industrial engineering.     

Non-monotonic material contrast in scanning ion and scanning electron images

30 keV Ga⁺ focused ion beam induced secondary electron (iSE) imaging was used to determine the relative contrast between several materials. The iSE signal compared from C, Si, Al, Ti, Cr, Ni, Cu, Mo, Ag, and W metal layers does not decrease with an increase in target atomic number Z₂, and shows a non-monotonic relationship between contrast and Z₂. The non-monotonic relationship is attributed to periodic fluctuations of the stopping power and sputter yield inherent to the ion–solid interactions. In addition, material contrast from electron-induced secondary electron (eSE) and backscattered electron (BSE) images using scanning electron microscopy (SEM) also shows non-monotonic contrast as a function of Z₂, following the periodic behavior of the stopping power for electron–solid interactions. A comparison of the iSE and eSE results shows similar relative contrast between the metal layers, and not complementary contrast as conventionally understood. These similarities in the contrast behavior can be attributed to similarities in the periodic and non-monotonic function defined by incident particle–solid interaction theory.     

Application of Feature Extraction through Convolution Neural Networks and SVM Classifier for Robust Grading of Apples

This paper proposes a novel grading method of apples,in an automated grading device that uses convolutional neural networks to extract the size,color,texture,an...     

分布动态载荷识别的抗噪处理

针对正交多项式频域法在用多种响应对矩形薄板进行载荷识别中抗噪性较差的问题,综合运用平均法、矩阵预处理和奇异值截断法等方法对之进行改善,并引入空间映射的思想,将该方法的应用范围拓展为复杂的模型.利用仿真算例,证实了该方法具有较好的抗噪性.     

基于MELTAC-N平台的核电厂安全级DCS环网研究与测试

针对工程实践中环网通讯相关问题的处理缺乏理论基础及国产化安全级DCS平台的开发缺乏成熟经验借鉴问题,对基于MELTAC-N平台核电厂安全级DCS环网的软硬件实现进行了研究。提出了安全级DCS环网双环网冗余设计、光切换开关设计等硬件设计方法,以及以RPR协议为基础,采用全数据收发策略的软件设计方法。在CPR1000安全级DCS平台上对安全级DCS环网的可靠性及实时性进行了评价,并进行了容错能力、响应时间及响应时间稳定性测试验证实验。结果表明,基于MELTAC-N平台安全级DCS环网软硬件设计具有较好的容错能力及响应时间稳定性。     

钒和铜对11Cr-2W低活化马氏体钢组织和高温力学性能的影响

研究了钒含量和0.22%铜对11Cr-2W低活化马氏体钢组织以及650℃下拉伸、蠕变性能的影响。结果表明:钒含量和0.22%的铜对钢的组织和M23C6相的尺寸没有明显影响,当钒的质量分数为0.105%时,基体中弥散分布的MX相最多且最为细小;当钒的质量分数从0.105%增加到0.203%时,试验钢的抗拉强度从325.2 MPa降低为289.4 MPa,蠕变寿命从370h缩至251h;添加0.22%的铜可以提高试验钢的蠕变寿命。     

凸轮轴加工的误差在线测量方法研究

提出了基于小波零相位滤波、三次样条插值对测试数据进行预处理,通过对预处理后数据与标准凸轮轮廓数据进行长信号相关法分析,进而实现相位角等关键参数和误差的在线提取方法.该方法能较好抵抗表面质量差和局部畸变等带来的测量风险,实现更高精度的测量.可通过机床改造升级植入,融入加工机床中,实现产品的质量在线检测和质量控制.     

Power system state estimation solution using modified models of PSO algorithm: Comparative study

The objective of all power system state estimation (PSSE) is to determine, by statistical projections, the best estimate of state variables represented by the voltage magnitudes and voltage angles of all the buses. Due to the complexity and non-linearity of the power system (PS), it is necessary to use more advanced methods for its analysis and control in real-time environment. This research discusses the application and the comparison of hybrid models of one of the algorithm using artificial intelligence (AI) technique (particle swarm optimisation ‘PSO’) in minimising the raw measurement errors in order to estimate the optimal point of the PS when certain sensitive data are incomplete. The effectiveness of the hybrid models are demonstrated and compared with the original PSO, artificial bee swarm optimisation (ABSO) algorithm and genetic algorithm (GA) using IEEE 14, 30, 118 and 300 bus test systems. Newton-Raphson load flow solution is taken as benchmark. Two different objective function formulations assessed by PSWV (Particle swarm without velocity equation), EPSOWP (Enhanced particle swarm optimiser incorporating a weighted particle), PSO-RF (PSO with repulsion factor) and CLPSO (Comprehensive learning PSO). The first formulation is the Weighted Least Square (WLS) and the second one is the Weighted Least Absolute Value (WLAV).     

基于PXIe总线的高速数据采集程控系统

针对单粒子撞击测试中窄脉冲信号的长时间检测问题,提出了一种基于PXIe总线以及数据采集卡的高速数据采集程控系统,实现了高速数据采集存储、实时脉冲数量统计、数据回放、远程控制仪器等方面功能,采用NI-PXI-5122数据采集卡实现了4通道、50 MSPS/Ch采样率、14 bit采样精度的同步采样,采用NI-HD-8265磁盘阵列实现了380 Mbyte/s以上数据流量1 h的连续流盘存储,应用Lab VIEW开发了系统软件,对采集流盘和程控仪器进行控制,利用模拟实验平台产生脉冲信号对系统的采集存储能力进行了测试。研究结果表明,该系统能以高采样率进行多通道的长时间数据采集,能够实现实时脉冲数量统计、数据回放、计算机远程控制等多项功能。     

Research on network integration technology of observation stations

According to the phenomenon of "four more"and"four low "problems in the observation stations,the surface-based meteorological observing system can't adapt to the change of the adaptive observation equipment and reduce of business intensification. A station integrated system is proposed,w hich can be configured,connected and extended to all kinds of observation equipment. And the integrated processor is designed,supporting a variety of communication interface standards. Flexible configuration,connection and expansion betw een conventional and new type of meteorological observation equipment are supported. It is capable for online calibration and maintenance of observation equipment. The effectiveness of automatic observation equipment is totally achieved to provide basic information support for disaster prevention and mitigation and national economic development.     

交通荷载作用下桥梁结构参数识别方法

应用动力节点加载法,将作用在桥梁上的交通荷载转化为等效节点荷载,再用两步构造法识别结构物理参数.第1步,用Newmark-β方法变换结构运动方程,并用结构的加速度响应求得变换空间内的位移、速度和加速度响应;第2步,基于最小二乘原理,构造出变换空间内求解结构参数的递推式,进行结构物理参数识别.数值模拟结果表明,在交通荷载作用下,该方法能够快速、准确地进行桥梁结构参数识别.     

The laboratory simulation of abrasive wear

Abrasive wear has long been recognised as one of the most potentially serious tribological problems facing the operators of many types of plant and machinery; several industrial surveys have indicated that wear by abrasion can be responsible for more than 50% of unscheduled machine and plant stoppages. Locating the operating point of a tribological contact in an appropriate operational ‚map’︁ can provide a useful guide to the likely nature and origins of the surface degradation experienced in use, though care must be exercised in choosing the most suitable parameters for the axes of the plot. Laboratory testing of materials and simulations of machine contacts are carried out for a number of purposes; at one level for the very practical aims of ranking candidate materials or surface hardening treatments in order of their wear resistance, or in an attempt to predict wear lives under field conditions. More fundamentally, tests may be aimed at elucidating the essential physical mechanisms of surface damage and loss, with the longer term aim of building an analytical and predictive model of the wear process itself. In many cases, component surface damage is brought about by the ingress of hard, particulate matter into machine bearing or sealing clearances. These may be running dry although, more usually, a lubricant or service fluid is present at the interface. A number of standardised wear test geometries and procedures have been established for both two- and three-body wear situations, and these are briefly described. Although abrasive wear is often modelled as following an ‚Archard’︁ equation (i.e. a linear increase in material loss with both load and time, and an inverse dependence on specimen hardness) both industrial experience and laboratory tests of particularly lubricated contacts show that this is not always the case: increasing the hardness differential in an abrasively contaminated lubricated pair may not always reduce the rate of damage to the harder surface.     

APPLICATION OF WAVELET TRANSFORM ON DIAGNOSIS AND PREDICTION OF MILLING CHATTER

In order to avoid the accuracy deterioration or tool damage caused by milling chatter, it is necessary to have an efficient and reliable diagnosis system that can on-line predict/detect the occur-rence of chatter. The diagnosis/predicting system proposed is to on-line process and analysis the vi-bration signals of the milling machine measured by accelerometers. According to the analysis results, the system will be able to detect/predict the occurrence of the chatter. The diagnosis algorithm is, first, collecting both the normal signals and chatter signals from milling processes, and then, converting the signals through wavelet transform and fast Fourier transform (FFT). Since the converted chatter sig-nals exhibit different characteristics from the normal signals, through defining the characteristic val-ues, such as root-mean-square value, max value, and ratio of peak value to root-mean-square value, etc, a diagnosis reference library that contains the distribution of these characteristic values is built for diagnosis. When a diagnosis is executing, the characteristic value of the measured signals is con-trasted with the diagnosis reference. The approach index which shows the possibility of occurrence of milling chatter will, then, be calculated through the diagnosis system. Cutting experiments are con-ducted to verify the proposed diagnosis system. The results show the success of early chatter detecting for the system.