同轴撞击流浓缩器的浓缩性能研究

从实验和理论上对撞击流浓缩器(ISC)进行了研究。实验主要研究了空气进口温度、空气进口流量、液滴加速管的长度对ISC容积蒸发系数的影响。研究结果表明:ISC的容积蒸发系数随空气进口流量的增加、空气进口温度的升高而增大;并证明,宜使用较短的加速管。在理论分析的基础上建立了ISC浓缩溶液的理论模型,借助基于该模型的数值计算,模拟了ISC内液滴的蒸发过程,通过与实验值的比较证明了模型的正确性。     

回路热管微通道换热器蒸发冷却实验

采用微通道换热器作为数据中心回路热管冷却换热器,在微通道冷凝器侧进行了蒸发冷却实验。实验利用焓差平台测量了不同因素对采用蒸发冷却技术的微通道冷凝器换热影响,并分析了室内外不同温差、室外不同湿度条件下采用蒸发冷却的微通道冷凝器及蒸发器的进出口空气温差。实验结果表明：采用蒸发冷却可使冷凝器入口空气温度实现大幅温降,并增加冷凝器及蒸发器的进出口空气温度差值,喷淋后可使流经热管空气降温0.3～1.9℃,增大2%～20%的系统换热量,冷凝器换热效率得以提升,并可扩大回路热管换热器使用地区,延长回路热管年利用时间。     

Application of an Air‐Operated Impinging Streams Contactor in Liquid‐Liquid Extraction

An experimental study was conducted on the liquid‐liquid extraction of isobutyric acid by means of cumene from its aqueous solutions in an air‐operated impinging streams contactor (AOISC) with spray nozzles. Aqueous and organic streams may or may not contact one another inside the spray nozzles depending on the modes of operation. The overall volumetric mass transfer coefficient, K_La, determined enabled us to evaluate the performance capability of the contactor. The effects of air and solution flow rates, contactor length and diameter, impingement zone as well as modes of operation have been investigated. These experimental results verify the capability of the method of impinging streams in liquid‐liquid extraction.     

同轴撞击流浓缩器浓缩溶液的理论研究

根据撞击流原理设计开发了一种新型溶液浓缩设备——撞击流浓缩器,在理论分析的基础上推导出撞击流浓缩器浓缩溶液的数学模型,运用实验结果验证了模型的正确性;基于该模型的数值计算结果,得到了浓缩器内气、液温度和速度及液滴浓度和累积蒸发量等沿轴向位移的变化。     

溴化锂溶液除湿器性能的实验研究

对逆流、散装填料、LiBr溶液的除湿器进行实验研究,实验过程中溶液流量为800～1600 L.h-1,入口溶液浓度为49%～54%,温度为28～41℃,空塔气速为0.39～0.96 m.s-1,入口空气湿度为10～21 g.kg-1。采用除湿量和体积传质系数来描述除湿性能,分析了溶液和空气入口参数对除湿性能的影响,得出平均体积传质系数为1.0 kg.m-3.s-1,液气比为2.5～3时可获到较好的除湿效果。比较了不同填料的除湿性能,鲍尔环填料除湿效果较好。同时对除湿过程进行了能量守恒分析,表明实验测量数据的准确性。实验结果为溶液除湿系统的性能分析及设计提供了依据。     

两种常用液体吸湿剂传质性能的比较

分析比较了溴化锂溶液（LiBr）、氯化锂溶液（LiCl）这两种常用的吸湿盐溶液与湿空气之间的传质性能,二者比较的基准是：溶液温度与表面蒸气压分别对应相等。相同状态时,LiBr溶液的密度约是LiCl溶液的1.2倍,比热容约是LiCl溶液的0.8倍,即当LiBr和LiCl溶液的体积流量相同时,二者的热容量大致相等。通过对热质交换过程解析解的分析,得到影响溶液与空气传质效果的核心参数为：空气与溶液的热容量比和传质单元数。在实验测试分别采用LiBr和LiCl溶液的除湿、再生工况性能的基础上,拟合出了传质系数随着空气与溶液进口参数的变化规律。在实验工况范围内,当LiBr与LiCl溶液的体积流量相同时,采用LiBr溶液的传质性能稍优于LiCl溶液,但二者差异不大。     

Heat and Mass Transfer between Air and Liquid Desiccant in Cross‐flow Contact Systems

In this paper, an analytical solution of the coupled heat and mass transfer process in a cross‐flow liquid‐desiccant dehumidifier/regenerator is developed. By the use of reliable assumptions, the government equations for the system are solved by an analytical method. The results of the present analytical solution are compared with experimental data from the literature, and they show good agreement. The maximum error produced by the presented analytical solution is less than 12 %. The effect of the operating parameters is considered using the presented analytical solution. The results show that air inlet humidity, air flow rate, desiccant inlet temperature, and desiccant inlet concentration have more influence on the moisture removal rate in the cross‐flow dehumidifier. Also, air inlet humidity, desiccant inlet temperature, desiccant inlet concentration and desiccant flow rate have more effect on the moisture removal rate in the cross‐flow regenerator. The effect of the Lewis number on the performance of the dehumidifier/regenerator is investigated. As the results show, by the use of Le = 1.08 in the dehumidification process and Le = 0.96 in the regeneration process, instead of the value of unity, better results are obtained. The benefit of the present study is a simplified application for the evaluation of the outlet parameters of the cross‐flow air dehumidifier/regenerator.     

无霜空气源热泵系统冬季除湿性能初步实验

通过对比现有的空气源热泵空调系统的优缺点，提出了一种新型无霜空气源热泵空调系统。该热泵系统最大的新颖之处在于热交换塔实现了“一塔三用”，不仅冬季可以无霜高效运行与再生，夏季蒸发冷却后性能也有所提升。通过搭建该系统实验平台研究了溶液塔入口空气温湿度、空气流量、溶液入口温度、溶液流量、溶液质量分数对除湿性能及空气出口温度与溶液出口温度的影响，结果表明：出口空气与溶液温度随入口空气温湿度、流量、溶液温度、质量分数的升高,溶液流量的下降而升高；溶液塔的除湿效率主要受风量和溶液流量的影响，而入口空气温湿度、入口溶液温度、溶液质量分数影响很小，溶液塔的除湿量随着室外空气湿度的升高、入口溶液温度的降低、空气流量和溶液流量的升高而升高。     

DIRECT CONTACT HEAT TRANSFER BETWEEN TWO IMMISCIBLE LIQUIDS

Direct-contact heat transfer between two immiscible liquids in turbulent pipe flow is studied under non-boiling conditions. The salt water and BP-Transcal 65 heat transfer oil are used as immiscible liquids. The diameter and the length of the pipe are 1.33 cm. and 304 cm., respectively. The effects of oil volume fraction, inlet salt water concentration, average liquid velocity, inlet oil temperature and pipe length on the over-all volumetric heat transfer coefficient are investigated.     

DIRECT CONTACT HEAT TRANSFER BETWEEN TWO IMMISCIBLE LIQUIDS

Direct-contact heat transfer between two immiscible liquids in turbulent pipe flow is studied under non-boiling conditions. The salt water and BP-Transcal 65 heat transfer oil are used as immiscible liquids. The diameter and the length of the pipe are 1.33 cm. and 304 cm., respectively. The effects of oil volume fraction, inlet salt water concentration, average liquid velocity, inlet oil temperature and pipe length on the over-all volumetric heat transfer coefficient are investigated.     

直接接触式冰浆生成器的单气泡传热特性

冰浆生成器是直接接触法冰浆制取系统的关键设备之一,而体积传热系数作为衡量冰浆生成器性能的重要参数受诸多因素影响。基于单个气泡在连续相中的上升特性,定性分析了各种因素对体积传热系数的影响。实验结果表明:进气温度下降、进气质量流量增加、水柱高度下降、喷嘴直径减小均导致体积传热系数增加。     

填料塔中哌嗪二胺吸收低浓度SO_2的传质性能

为满足有机胺法脱硫设计开发的需要,采用动态吸收法测定了填料塔中哌嗪二胺(PA-A)水溶液吸收低浓度SO2的体积总传质系数KGa,考察了吸收工艺参数如吸收液中的PA-A浓度和初始pH值、液相流率、吸收温度、进气SO2浓度及流速等对KGa的影响。结果表明:KGa随着吸收液中的PA-A浓度和初始pH值、液相喷淋密度的增加而增大;随着吸收温度、气相流率及进气SO2浓度的增加而减小。通过实验结果分析得到体积总传质系数KGa与气液相流率比(qG/qL)之间符合指数关系式,该经验关系可用于工程设计计算。     

Effects of Contaminants on the Mass‐Transfer Characteristics of a Two‐Impinging‐Streams Gas‐Liquid Reactor

The mass‐transfer characteristics of a new type of two‐impinging‐streams reactor (TISR) was studied by means of sodium sulfite solution as the liquid phase and air as the gas phase, in the presence and absence of various types of surface‐active agents (SAAs). The influences of anionic, cationic, and nonionic SAAs on the specific interfacial area and overall volumetric mass‐transfer coefficient obtained in the TISR were investigated. It was found that the presence of a little amount of the above‐mentioned contaminants increases the specific interfacial area and decreases the overall volumetric mass‐transfer coefficient. On the basis of the experimental results obtained for various types of SAAs, correlations were derived for the interfacial area as well as the Sherwood number for the liquid phase in terms of Froude, Reynolds, Schmidt, and Morton numbers.     

采用填料强化的鼓泡塔直接接触换热性能研究

以正戊烷-水为物系,进行了采用填料强化的鼓泡塔直接接触蒸发换热实验。实验采用顺流操作,考察了分散相流量、温差以及分布器孔径对体积换热系数和汽化高度的影响。实验得出：在戊烷流量为23.868 L/h,分布器孔径为2.5 mm时加填料的鼓泡塔的体积换热系数约为未加填料的2倍;在一定的操作条件下,加填料的鼓泡塔中汽化高度随分散相流量和分布器孔径的增大而增加,随温差的增大而减小;加填料的鼓泡塔中体积换热系数随分散相流量的增加而增加,随分布器孔径的增大而减小,与温差成负幂指数关系。     

Mathematical Model of Fixed-Bed Drying and Strategies for Crumb Rubber Producing STR20

The objectives of this research were to investigate empirical and diffusion models for thin-layer crumb rubber drying for producing STR20 rubber using hot air temperatures of 110–130°C and to study the effect of drying parameters such as inlet drying temperature, volumetric flow rate, and initial moisture content on the quality of dried rubber. Finally, a mathematical drying model for predicting the drying kinetics of crumb rubber was developed using inlet air flow rates of 300–600 m³/min-m³ of crumb rubber (equivalent to 1.8–5.0 m/s) with the crumb rubber thickness fixed at 0.25 m. The average initial moisture content of samples was in the ranges of 40 and 50% dry basis while the desired final moisture content was below 5% dry basis. The results showed that the drying equation of crumb rubber was highly related to the inlet air temperature, while the drying constant value was not proportional to the initial moisture content. Consequently, the experimental data were formulated using nine empirical models and the analytical solution of moisture ratio equation was developed by Fick's law of diffusion. The result showed that the simulated data best fitted the logarithmic model and was in reasonable agreement to the experimental data. The effective diffusion coefficient of crumb rubber was in the range of 1.0 × 10^?9 to 2.15 × 10^?5 m²/s corresponding to drying temperatures between 40 and 150°C, respectively. The effects of air recirculation, inlet drying temperature, initial moisture contents, air flow rate, and drying strategies on specific energy consumption and quality of samples were reported. The experiments were conducted using two different drying strategies as follows: one-stage and two-stage drying conditions. The results showed that initial moisture content and air flow rates significantly affected the specific energy consumption and quality of rubber, while the volumetric air flow rate acted as dominant effect to the specific energy consumption. The simulated results concluded that the percentage of recycled air between 90 and 95% provided the lowest specific energy consumption as compared to the others.     

回转窑供风管参数对窑内热工状况的影响

以2.3 m×55 m的炭素回转窑作为研究对象,应用流体模拟软件Fluent 和Matlab 分别对其气体空间和物料料层内的传热过程进行了研究。通过改变二、三次供风管的长度和供风管入口处的空气吹向,得到了相应条件下窑内的温度分布,并进行了比较和分析。结果表明：二、三次供风管的长度对窑内温度场的影响较小,实践中可以采用无管供风措施,以解决供风管道烧损问题;当二、三次供风管在某一长度下窑内煅烧带温度较高时,其窑内剩余的可燃气体较低;二、三次供风管入口处空气均吹向窑头时,窑尾处剩余可燃气体浓度较大,但其煅烧带温度较高,煅烧带长度较长;当二、三次供风管入口处空气均吹向窑尾时,窑尾处剩余可燃气体浓度较小,但其煅烧带温度较低,煅烧带长度较短。     

对撞流干燥的实验与理论研究

The experiments of one-stage semi-circular and two-stage semi-circular impinging stream drying as well as the vertical and semi-cricular combined impinging stream drying were carried out.The velocity distribution and the mean residence time of particles,and the influence of various factors on drying characteristics were studied.A mathematical model of granular material drying in a semi-circular impinging stream dryer was proposed,in which the flow characteristics as well as the heat and mass transfer mechanisms were considered.Reasonable numerical methods were used to solve the equations.Under various conditons,the calculated results of drying rate and moisture content versus time were obtained.The results indicate that constant drying rate period does not exist in a semi-circular impinging stream dryer.Appropriate semi-cricular stage number and curvature radius,flow-rate ratio,air velocity,and higher inlet air temperature should be used for enhancing the drying process.     

撞击流混合器微观混合性能的研究

撞击流混合器是一种新型的微观混合器,今研究了T型直流对撞(IS)、锥形对撞(CIS)、直流旋撞(VS)和二次旋流旋撞(TVS)四种结构的撞击流混合器的微观混合性能。然后以Villermauxu/Dushman快速平行竞争反应测定混合器的离集指数Xs,并考察了流体流速、流体流速比和混合器结构对离集指数的影响。混合器混合效果用离集指数来衡量,离集指数越小混合效果越好。结果表明:其余工艺条件相同的情况下,流体流速越大,离集指数Xs愈小;两股流体流速比越小,离集指数Xs愈小;喷嘴进口管道直径越小,离集指数Xs愈小。锥形的比直线形的、旋流比直接撞击流混合效果要好,而且旋流使物料在混合器中的停留时间延长;根据实验数据模拟计算,T形撞击流微混合器的微观混合时间在1 ms数量级;用Fluent 6.2.1商业软件模拟计算了混合器内的流场分布情况,发现模拟计算结果和实验结果基本吻合。     

基于热质传递解耦特性的溶液除湿过程传热传质系数(Ⅱ)实验与Le-hD分离测量法应用

对采用规整波纹填料结构的溶液除湿器除湿过程进行了实验研究,空气与溶液流型组织形式为叉流,基于Le-hD分离测量法得到空气入口流量、温度、含湿量以及溶液入口质量分数、温度对耦合传质系数的影响,并采用数据回归的方法对传质系数与Lewis数进行拟合,得到该类结构除湿器除湿过程的传质系数与Lewis数的关联式,并进行了74组稳态实验对该关联式进行误差分析与验证,结果表明根据关联式计算得到的进出口参数变化与实验进出口参数变化之间相对误差很小,进出口空气温度变化、含湿量变化误差分别仅在6%、10%以内,进出口溶液温度变化相对误差不超过12%,表明Le-hD分离测量法的准确性和可接受性。     

基于热质传递解耦特性的溶液除湿过程传热传质系数(Ⅱ)实验与Le-hD分离测量法应用

对采用规整波纹填料结构的溶液除湿器除湿过程进行了实验研究,空气与溶液流型组织形式为叉流,基于Le-h_D分离测量法得到空气入口流量、温度、含湿量以及溶液入口质量分数、温度对耦合传质系数的影响,并采用数据回归的方法对传质系数与Lewis数进行拟合,得到该类结构除湿器除湿过程的传质系数与Lewis数的关联式,并进行了74组稳态实验对该关联式进行误差分析与验证,结果表明根据关联式计算得到的进出口参数变化与实验进出口参数变化之间相对误差很小,进出口空气温度变化、含湿量变化误差分别仅在6％、10％以内,进出口溶液温度变化相对误差不超过12％,表明Le-h_D分离测量法的准确性和可接受性。