Pasting,Thermal, Hydration,and Functional Properties of Annealed and Heat-Moisture Treated Starch of Sword Bean (Canavalia gladiata)

The effects of annealing (ANN) and heat-moisture treatments (HMT) on the physicochemical and functional properties of Sword bean starches were investigated. The pasting properties differ significantly among the starches, with peak viscosity ranging from 399.17 RVU to 438.33 RVU; however, all the starches exhibited ‘Type C’ class with restricted swelling. The HMT starches had the highest gelatinization temperature, while change in enthalpy of gelatinization, ΔH_gel of the native starch, was higher (13.82 J/g) than that of the modified starches (1.39–6.74 J/g). The solubility and swelling power of all the starches increased as the temperature increased. The oil and water absorption capacity of the starches ranges between 3.24–3.91 g/g and 2.42–3.35 g/g, respectively. HMT (at 25 and 30% moisture level) changes the X-ray diffraction pattern of the starch from Type ‘B’ to Type ‘C’. The Scanning electron micrograph results revealed the starch granules with smooth ellipsoids and indentation in their centre, hydrothermal modification showed little effect on the morphology and size of the granules. Hydrothermal modification improved the physicochemical and functional properties of the starch without destroying the granule of the starch.     

Characterization of amorphous granular starches prepared by high hydrostatic pressure (HHP)

Amorphous granular starches (AGS) and non-granular amorphous starches (non-AGS) of corn, tapioca and rice were prepared using high hydrostatic pressure (HHP) treatment with ethanol and water washing, respectively and their physicochemical properties were investigated. Water holding capacity and apparent viscosity of AGS and non-AGS were higher than those of native one in all starches. In RVA pasting properties, AGS and non-AGS showed higher pasting temperature and lower peak viscosity than those of native one. Furthermore, non-AGS showed distinctively lower peak viscosity compared to that of AGS possibly due to its non-granular structure. Apparent viscosity of non-AGS revealed relatively lower than commercial pre-gelatinized starch because of heat and pressure-induced gelatinization. Maintaining granular structure in HHP treated pre-gelatinized starch provide a distinctive physicochemical characteristics compared to native starch and preparation of gelatinized starch with different gelatinization and washing methods could cause big differences in their physicochemical properties.     

Physico-chemical properties of flour and starch from jackfruit seeds (Artocarpus heterophyllus Lam.) compared with modified starches

Jackfruit (Artocarpus heterophyllus Lam.) is one of the most popular tropical fruits grown in Asia. The objective of this study was to compare physico‐chemical properties of native flour and starch from jackfruit seeds (A. heterophyllus) to commercially modified starches (Novation 2300 and Purity 4). The colour of jackfruit seed starch was lighter than the Novation 2300 starch but darker than the Purity 4 starch. The jackfruit seed starch had a narrower gelatinization temperature range than Purity 4 and required less gelatinization energy compared with modified starches. The peak viscosity of jackfruit seed starch was lower than commercially modified starches. Likewise, setback viscosity, swelling power and solubility of jackfruit seed starch showed similar trends. Results from this study suggest that native starch from jackfruit seed could be used as an alternative for modified starches in a system needing starch with a high thermal and/or mechanical shear stability.     

Preparation and Aqueous Properties of Starch‐grafted Polyacrylamide Copolymers

In the present work, starch‐grafted polyacrylamide copolymers were prepared and their rheological properties, either in water or in water‐based muds, were investigated. The advantages in using starches as substrates to prepare additives which are suited for improving stability and the rheological properties of water‐based muds, lie in their low cost, and their lower biodegradability than native starches. Thus, various copolymer series were prepared by free‐radically grafting acrylamide (AM) onto starch using ceric ammonium sulphate (CAS) as initiator. It is shown that the intrinsic viscosity and the molecular weight of the grafted starches are controlled by the initiator and monomer concentrations. Furthermore, to predict the behaviour of the samples under oil‐well conditions, the aqueous solution properties of the copolymers such as water solubility, viscosity, shear rate, were determined as function of temperature, salt concentration and type, and aging time. The knowledge of these properties is a prerequisite for the use of the copolymers in drilling fluids. The data indicate that starch‐grafted polyacrylamide copolymers as compared to the non‐modified starch, behave as shear‐thinning, are salt resistant, and their rheological properties are stable with time. The grafted starches as prepared above were also added to water‐based mud and the rheological properties of the resulting muds were determined under oil‐well conditions. Grafted starches, having high AM contents, are more efficient in decreasing the filtrate volume, and increasing the plastic viscosity of the muds, when compared to PAC‐L, a modified cellulosic polymer used in the filtration control of most water‐based muds. Such improvements in the rheological properties of the muds were found to result from the behaviour and/or properties of the grafted starches in water.     

Morphological,physicochemical, and pasting properties of modified water chestnut (Trapabispinosa) starch

Selected physicochemical properties of native and modified water chestnut starch (Trapabispinosa) were studied. Single- and dual-modifications were carried out by pregelatinization, acetylation and acid-thinning methods. Chemical modification created unevenness on the surface of starch granule. Swelling power, solubility, and water retention capacity were improved by all modification techniques used. The peak viscosity was reduced in all modified starches as compared to native water chestnut starch. The setback value which is an indication of retrogradation (re-association of starch molecules) tendency in the starch paste was reduced after pregelatinization and acid-thinning but increased by acetylation.     

Preparation and physicochemical properties of modified jackfruit starches

Modifications of jackfruit starch, extracted from the cotyledons of Artocarpus heterophyllus Lam. (Thong Prasert cultivar), were carried out to obtain a pregelatinized starch, three (m-, n- and i-) carboxymethyl starches, a hydroxypropyl starch and a phosphate cross-linked starch. Physicochemical properties of native and modified jackfruit starches were comparatively investigated. Pregelatinized, hydroxypropyl, and cross-linked starches were insoluble or partially soluble in water at room temperature, while carboxymethyl starches were soluble with good overall water uptake. Scanning electron microscopic images revealed that granules of most modified jackfruit starches retained the native appearance and crystal structure, with the exception of pregelatinized starch and two (n- and i-) carboxymethyl starches, which showed significant breakage of granules. X-ray diffraction patterns corroborated to suggest the loss of crystallinity in these modified starches. Thermal analysis showed a significant decrease in the gelatinization temperature of hydroxypropyl starch with no change in enthalpy, while higher gelatinization temperature and less enthalpic value were observed for pregelatinized starch. Pregelatinized and hydroxypropyl starches showed temperature-dependent improvement on swelling and solubility, while cross-linked starch exhibited less solubility. Aqueous solution of m-carboxymethyl starch yielded the highest apparent viscosity with improved heating-cooling stability.     

Hydrothermal Modifications of Tropical Tuber Starches. 1. Effect of Heat‐Moisture Treatment on the Physicochemical,Rheological and Gelatinization Characteristics

Cassava, sweet potato and arrowroot starches have been subjected to heat‐moisture treatment (HMT) under different conditions using a response surface design of the variables. A comparative study was performed on the pasting properties, swelling behaviour and the gelatinization properties of the modified starches and also on the rheological and textural properties of their pastes. X‐ray diffraction studies have shown that cassava starch exhibited a slight decrease in crystallinity, whereas sweet potato and arrowroot starches showed an increase in crystallinity after HMT at 120ºC for 14 h with 20% moisture. The swelling volume was reduced and the solubility was enhanced for all three starches after HMT, but both effects were more pronounced in the case of arrowroot starch. The decrease in paste clarity of the starch after HMT was higher in the case of cassava and sweet potato starches. Viscosity studies showed that the peak viscosity of all three starches decreased after HMT, but the paste stability increased as seen from the reduced breakdown ratio and setback viscosity. Studies on rheological properties have shown that storage and loss moduli were higher for the starches heat‐moisture treated at higher moisture and lower temperature levels than the corresponding native starches. Storage of the gel at ‐20ºC resulted in a significant increase in storage modulus for all the three starches. All the textural parameters of the gels were altered after the treatment which depended on the nature of the starch and also the treatment condition.     

Characterization of Phosphate Monoester Resistant Starch

The properties and structures of corn, wheat, and potato native starches and their phosphate monoester resistant starches were tested and compared. The results indicated that the resistant starch content, light transmittance, and freeze-thaw stability of the phosphate monoester resistant starch increased after modification. The native starches exhibited much higher peak viscosities compared with resistant starch (RS) and phosphate monoester resistant starches. The phosphate monoester resistant starch from corn and wheat starch exhibited a higher peak and final viscosity and lower gelatinization temperatures compared with the resistant starch, while the peak and final viscosity of the potato phosphate monoester resistant starch samples were lower than that of potato resistant starch. In the FT-IR graph, a new peak at 1244 cm^?1 (P=O bond) was observed for all kinds of phosphate monoester resistant starch.     

两种大米淀粉及其磷酸酯淀粉理化特性的比较研究

对比分析2种大米(籼米和粳米)的全粉、淀粉和取代度均为0.068的磷酸酯淀粉的理化特性.粳米的全粉、淀粉和磷酸酯淀粉的膨胀力分别为7.5,10.7,21.6 g/g,分别高于籼米的全粉、淀粉和磷酸酯淀粉的膨胀力(5.8,8.9,17.4 g/g).2种大米淀粉经磷酸酯化后透光率增高,相应淀粉的透光率次之,全粉的透光率最低,籼米的全粉、淀粉和磷酸酯淀粉的透光率分别低于粳米的全粉、淀粉和磷酸酯淀粉的透光率.经快速黏度分析仪测定的糊化特性结果表明,淀粉或变性淀粉膨胀力高,其峰值黏度和崩解值也高,此外,蛋白质含量和直链淀粉含量也极大的影响了淀粉的糊化特性.使用动态流变仪测定的流变特性表明,在相同的温度下,籼米的全粉、淀粉和变性淀粉的储能模量(G')分别比粳米的全粉、淀粉和变性淀粉的储能模量(G')高,对于相同的大米品种,全粉的储能模量(G')最高,变性淀粉的储能模量(G')最低.     

酸解和乙酰化改性对木薯淀粉性质的影响

以木薯淀粉为原料,对酸解淀粉、乙酰化淀粉及酸解乙酰化淀粉的糊性质进行了研究,并用扫描电子显微镜、X射线衍射仪和傅里叶变换红外光谱仪对改性淀粉的形貌和结构进行了分析。结果表明:木薯淀粉经酸解改性改善了糊的透明度,膨胀度有所降低,糊化温度升高,峰值黏度显著降低,凝沉性有所改善;乙酰化改性增加了淀粉糊的透明度,膨胀度提高,降低了糊化温度,峰值黏度增加,糊的抗凝沉性增强但热糊稳定性差;酸解乙酰化复合改性显著提高了淀粉糊的透明度,降低淀粉的膨胀度及糊化温度,峰值黏度显著降低,抗凝沉性明显增强,冷、热糊稳定性提高。扫描电镜、X衍射数据及红外图谱表明,3种变性处理均没有改变木薯淀粉的晶型和基本结构,颗粒形貌也没有发生显著变化。     

改性玉米淀粉的物理化学研究

对天然玉米淀粉和五种化学改性玉米淀粉的糖化性质进行了比较。改性玉米淀粉包括下列五种,磷酸淀粉,交联磷酸淀粉,醋酸淀粉A,醋酸淀粉B和羟丙基淀粉。使用差热扫描量热计测定了糊化的热力学参数,同时用显微镜观察了糊化过程。研究表明,五种改性玉米淀粉的糊化热都比天然的玉米淀粉小,测量冷的淀粉糊的流动性质表明只有羟丙基玉米淀粉比天然玉米淀粉的帖度高。     

Influence of prior acid treatment on physicochemical and structural properties of acetylated sorghum starch

Influence of prior acid treatment on acetylation of starch isolated from an Indian sorghum cultivar was investigated. The starch was acid thinned (AT) using 0.1, 0.5, and 1 M HCl for 1.5 h and then acetylated (Ac) with acetic anhydride (8% w/w). The acid thinning and subsequent acetylation appeared to reduce the percentage acetylation as indicated by degree of substitution. Ac‐AT starches exhibited significantly different physicochemical, thermal, pasting, and gel textural properties from those of AT and Ac starches. Starches after dual modification showed higher solubility, lower AM content, gelatinization temperatures, retrogradation, peak viscosity, and gel hardness than native starch. Enthalpy and range of gelatinization were observed to be higher in dual modified starches than native starch. However, no significant changes in granule morphology or crystalline pattern of Ac‐AT starches were observed compared with native starch.     

Hydroxypropylation of pigeon pea (Cajanus cajan) starch: Preparation, functional characterizations and enzymatic digestibility

Hydroxypropyl starch derivatives were prepared from pigeon pea starch (NPPS) which is an unconventional starch source. Functional parameters and characterization of both native and modified starches were carried out. The starch granules appeared oval or elliptical in shape with sizes ranging from 7 to 40 μm in width and 10 − 30 μm in length. Hydroxypropylation did not alter the shape of the starch granules in a pronounced way. Generally, the x-ray diffractograms of native pigeon pea starch showed the “A” pattern. However, slight reductions in the diffraction intensity of starches after modification were observed. At all temperatures studied (30-90 °C), swelling and solubility of hydroxypropylated starches were higher than the NPPS. Progressive increases in swelling capacity and solubility were observed as the molar substitution (MS) increased among the hydroxypropylated starches. Hydroxypropylation reduced starch paste turbidity on storage. Also, studies showed that syneresis reduced after hydroxypropylation. In addition, syneresis reduced as the MS of the hydroxypropyl starches increased. The results indicate that pasting temperature and peak temperature reduced after modification but peak viscosity increased in hydroxypropylated starch derivatives compared with the native starch. Setback reduced in hydroxypropylated starches compared with the native starch. Enthalpy of gelatinization and percentage retrogradation reduced after hydroxypropylation and progressive reductions were observed as the MS increased among the starch derivatives. Hydroxypropylation increased enzymatic digestibility.     

干热处理对藜麦淀粉结构和理化性质的影响

以高筋小麦粉为原料添加酵母制作面团,在温度28℃、湿度80%条件下发酵1～6 h,提取小麦淀粉。研究发酵时间对小麦直链淀粉含量、损伤淀粉含量、粒径、颗粒表面结构、糊化及消化特性的影响。结果表明：面团发酵1 h后直链淀粉含量和损伤淀粉含量均显著低于原淀粉(P<0.05)。快速黏度分析结果表明,发酵1 h的小麦淀粉峰值黏度、热浆黏度和冷浆黏度最低。发酵处理后淀粉的粒径均小于原淀粉,其中发酵5 h的平均粒径最小。扫描电镜结果表明,发酵6 h的小麦淀粉颗粒表面出现破裂现象。体外消化实验表明,发酵5 h和6 h小麦淀粉的消化速率最高,发酵后抗性淀粉含量低于原淀粉,而慢消化淀粉含量高于原淀粉(P<0.05)。     

Effect of ionic gums and dry heating on physicochemical,morphological, thermal and pasting properties of water chestnut starch

Starch from water chestnuts (Trapa natans) was isolated and modified by dry heating and hydrocolloids [carboxy methyl cellulose (CMC) and sodium alginate]. Native and modified starches were evaluated for their physicochemical, pasting, thermal and morphological properties. Pasting and thermal properties were studied using Rapid Visco Analyzer (RVA) and Differential Scanning Calorimeter (DSC) respectively. Morphological properties were studied by Scanning Electron Microscopy (SEM). Modification of the starch by dry heating with and without gums reduced paste clarity and increased the water and oil binding capacity; solubility and swelling power decreased. Dry heating of native starch increased peak viscosity; however, with addition of CMC, peak viscosity decreased. Starch modified with CMC and 4 h heating exhibited lowest gelatinization temperature (T₀). Pasting characteristics of native water chestnut starch were largely affected by the addition of gums and/or heat treatment. Overall onset gelatinization temperature reduced with heat treatment and addition of gums. Morphological studies revealed no significant variation in starch granule size. Starch granules were seen agglomerated because of leaching of amylose and granule interspacing decreased with addition of gums.     

Influence of Heat‐Moisture Treatment and Acid Modifications on Physicochemical,Rheological, Thermal and Morphological Characteristics of Indian Water Chestnut (Trapa natans) Starch and its Application in Biodegradable Films

Water chestnut starch was subjected to acid modification and heat‐moisture treatment. Hydrochloric acid was used for acid modification at three different concentrations (0.25 M, 0.5 M and 1 M) for 2 h. Modifications did not alter the granule morphology. Heat‐moisture treatment (HMT) resulted in slight reduction in the granular size of the starch granules. Acid modification lowered the amylose content, swelling power, water‐ and oil‐binding capacity but improved the solubility of starch to a considerable level. Light transmittance of acid‐modified (AM) starches improved significantly. A significant reduction in peak, trough, final and setback viscosity was observed by acid‐thinning. In case of heat‐moisture treated starch the final viscosity (F_v) was found to be even higher than the peak viscosity (P_v). Native water chestnut starch exhibited a lower onset temperature (T_o) and peak temperature (T_p) of gelatinization than the corresponding acid‐treated starches. Starch films prepared from native starch exhibited excellent pliability, whereas those prepared from AM and HMT starches showed good tensile strength. Starch films prepared from acid‐treated starches provided better puncture and tensile strength.     

瓜尔胶和黄原胶对马铃薯淀粉及其变性淀粉糊化和流变性质的影响

研究瓜尔胶和黄原胶对马铃薯淀粉、马铃薯磷酸酯淀粉和马铃薯阳离子淀粉糊化和流变性质的影响。糊化性质实验表明瓜尔胶增加了3种淀粉的峰值黏度和成糊温度,降低了淀粉糊的热稳定性。黄原胶降低了马铃薯淀粉和马铃薯磷酸酯淀粉的峰值黏度并提高了糊的热稳定性和成糊温度,但对马铃薯阳离子淀粉起相反作用。动态流变实验表明加入黄原胶显著提高了3种淀粉的GO`、GO`O`值,降低了损耗角正切值tanδ,黄原胶对马铃薯阳离子淀粉动态流变学性质的影响最大,瓜尔胶对3种淀粉的动态流变学性质的影响不显著。静态流变实验表明加入瓜尔胶和黄原胶后的淀粉糊仍为假塑性流体,滞后环面积减少,稳定性提高,两种胶对马铃薯淀粉和马铃薯磷酸酯淀粉的作用比对马铃薯阳离子淀粉作用明显,并且黄原胶比瓜尔胶对淀粉作用更为显著。研究发现胶体与淀粉之间的电荷相互作用对复配体系的糊化性质和流变学性质起重要的作用。     

Effects of annealing on the physicochemical properties and enzymatic susceptibility of rice starches with different amylose contents

This study investigated the effects of annealing (ANN) on the properties of rice starches with high, medium and low-amylose contents. The starches were heated with excess water at 45 °C, 50 °C and 55 °C for 16 h. The swelling power, solubility, pasting properties, enzymatic susceptibility, morphology and X-ray crystallinity of the starches were evaluated. Annealing reduced the swelling power and solubility of the starches. ANN at 55 °C increased the pasting temperature and decreased the peak viscosity of the high-amylose rice starch. However, annealing decreased the peak viscosity of the low-amylose starch. The annealed rice starches presented a lower final viscosity and setback than did the native starches, with the exception of the low-amylose starch, which showed an increase in setback. Annealing increased the starches’ susceptibilities to α-amylase and promoted a reduction in their relative crystallinity.     

Physicochemical,crystallinity, pasting and thermal properties of heat‐moisture‐treated pinhão starch

The effect of heat‐moisture treatment (HMT) on the properties of pinhão starches under different moisture and heat conditions was investigated. The starches were adjusted to 15, 20 and 25% moisture levels and heated to 100, 110 and 120°C for 1 h. The X‐ray diffractograms, swelling power, solubility, gel hardness, pasting properties and thermal properties of the native and HMT pinhão starches were evaluated. Compared to native starch, there was an increase in the X‐ray intensity and gel hardness of HMT starches, with the exception of the 25% moisture‐treated and 120°C heat‐treated starch. HMT reduced the swelling power and solubility of the pinhão starches when compared to native starch. There was an increase in the pasting temperature, final viscosity and setback and a decrease in the peak viscosity and breakdown of HMT pinhão starches compared to native starch. HMT increases the gelatinisation temperature of native pinhão starch and reduces gelatinisation enthalpy.     

Thermal properties of new varieties of yam starches

Starches isolated from yam varieties of Dioscorea alata and Dioscorea cayenensis‐rotundata species were prepared at different time–temperature conditions and characterised by DSC, amperometric iodine titration, light microscopy and rheology and compared to native and chemical modified tapioca starches. The observation by light microscopy showed different morphologies of the granules when heated above 100°C and the tendency for disintegration decreased in the order native tapioca starch > yam starch > modified tapioca starch. Differences between yam and tapioca starches were also revealed by DSC. Yam starch enthalpy is higher than tapioca starch, but the peak temperature is low. However, the significant differences between yam and the other tested starches were found in terms of their rheological behaviour. The viscosity of yam starch was very stable at high temperatures on the viscograph. With this property, yam starch can be used as thickening and gelling agent in food.