WC颗粒增强镍基合金喷熔层腐蚀磨损行为及其人工神经网络预测分析

采用氧一乙炔焰喷熔工艺制备了碳化钨（WC）颗粒增强镍基合金喷熔层,研究了它的腐蚀磨损行为。结果表明：喷熔层耐腐蚀磨损性能随WC含量增加而提高,WC含量在20％～30％范围内,喷熔层耐腐蚀磨损性能最佳,超过30％时,其耐腐蚀磨损性能下降。载荷增加,腐蚀磨损率增大;速度增加,腐蚀磨损率下降。低速重载荷时,WC颗粒增强效果明显,且含30％WC喷熔层耐腐蚀磨损性能最好;高速轻载荷时,因WC原电池效应显著,WC颗粒增强效果减弱。基于人工神经网络的喷熔层腐蚀磨损行为预测与实验结果吻合较好,对喷熔层的应用具有重要指导作用。     

爆炸喷涂WC/12%Co涂层的干滑动磨损研究

主要研究了爆炸喷涂WC/12%Co陶瓷涂层与浸树脂石墨在干滑动摩擦条件下的磨损性能,并分析了其磨损机理。实验结果表明:在干滑动摩擦条件下,WC/12%Co涂层磨损率随载荷和速度的增大而增大,当载荷超过40 N时,出现磨损突变现象;同时发现,陶瓷材料磨损率随摩擦时间呈先减小后增大的趋势。其主要的磨损机理为粘着磨损和脆性断裂。     

38CrSi自配副的摩擦磨损性能

采用自制的销盘式摩擦磨损试验机研究了38CrSi自配副干滑动时的摩擦因数、磨损率随滑动速度和载荷的变化规律;利用SEM观察了磨损面的微观形貌,分析了摩擦磨损机理。结果表明:其摩擦因数随着载荷和速度的增加而减小;磨损率随着载荷的增加而增大,随着速度的增加先增大后减小,和常用材料的磨损率随速度增加而增大的规律不同;磨损机理为磨粒磨损和粘着磨损。     

38CrSi自配副的摩擦磨损性能

采用自制的销盘式摩擦磨损试验机研究了38CrSi自配副干滑动时的摩擦因数、磨损率随滑动速度和载荷的变化规律;利用SEM观察了磨损面的微观形貌,分析了摩擦磨损机理。结果表明：其摩擦因数随着载荷和速度的增加而减小;磨损率随着载荷的增加而增大,随着速度的增加先增大后减小,和常用材料的磨损率随速度增加而增大的规律不同;磨损机理为磨粒磨损和粘着磨损。     

Ni-Mo-P-Si3N4化学镀层的摩擦磨损性能研究

Q215碳素钢表面上制备一层Ni-Mo-P-Si3N4复合镀层,在MS-T3000摩擦磨损试验机上进行摩擦磨损试验,记录平均摩擦系数,测试磨痕宽度,计算磨损率,研究该化学镀层的摩擦磨损性能。分析结果表明:载荷不变时,平均摩擦系数和磨损率均随滑动速度的增大而增大;滑动速度不变时,平均摩擦系数和磨损率均随载荷的增大而增大;载荷和滑动速度不变时,平均摩擦系数和磨损率随镀层中Si3N4的体积分数先增大后减小。     

铜锡铅锌合金的摩擦磨损性能

利用MMU-200型摩擦磨损试验机研究了铜锡铅锌合金与GCr15钢对磨时的摩擦磨损特性,利用扫描电子显微镜对合金的磨损表面形貌进行了观察。结果表明:铜锡铅锌合金的磨损率随载荷和摩擦速度的增加而增大;其摩擦因数随摩擦速度的增加而减小,随载荷的增加先增大后减小;其磨损机制主要为磨粒磨损和粘着磨损;合金中的铅相起到了润滑作用,有利于提高合金的耐磨性能。     

WC/TiC层状陶瓷刀具与316L不锈钢间的干摩擦磨损性能研究

研究了在1 750℃下真空热压烧结而成的WC/TiC层状陶瓷刀具材料在干摩擦条件下与316L奥氏体不锈钢之间的摩擦磨损性能,并对磨损面进行了分析。结果表明:载荷和滑动速度对摩擦因数和磨损量的影响较大,随着载荷的不断增大,WC/TiC层状陶瓷刀具材料的摩擦因数和磨损量呈增大趋势;而随着滑动速度的增大,WC/TiC层状陶瓷刀具材料的摩擦因数先降后增,磨损量先增后降;在WC/TiC层状陶瓷刀具材料与316L奥氏体不锈钢的对磨过程中,材料的表面发生了犁削、颗粒及片层剥落现象,在磨损表面留有犁沟、凹坑、微裂纹和片层结构,其磨损机理为磨粒磨损和粘着磨损。     

载流条件下铬青铜/纯铜摩擦副摩擦磨损性能研究

在自制的销盘摩擦磨损试验机上,对铬青铜/纯铜摩擦副进行载流条件下的干滑动模拟试验,研究了电流、速度、载荷对铬青铜/纯铜摩擦磨损性能的影响规律。试验结果表明:电流是影响摩擦副摩擦磨损性能最显著的因素,摩擦因数和磨损率都随着电流的增大而增大;速度和载荷对摩擦因数和磨损率也有显著影响;电流的存在,摩擦副间产生了比无电流时更严重的粘着磨损和塑性变形,同时增加了电化学腐蚀,使磨损更加严重。     

铜碲硒铁合金的干摩擦磨损性能

利用环-盘式摩擦磨损试验机研究了铜碲硒铁合金的干摩擦磨损行为,分析了载荷和摩擦速度等参数对该合金摩擦磨损性能的影响,并用扫描电子显微镜对磨损形貌进行了观察.结果表明:铜碲硒铁合金的摩擦因数随载荷的增加变化不大,但随摩擦速度的增加而明显增大;合金的磨损率随载荷和摩擦速度的增加均增大;在轻载低速条件下,合金的磨损机制以犁削磨损和粘着磨损为主;在重载高速条件下,磨粒磨损和粘着磨损加剧.     

模拟体液环境下TAMZ合金的微磨粒磨损行为研究

采用TE66试验机对新型TAMZ钛合金的微磨粒磨损行为进行了研究.系统地考察了载荷、料浆浓度等因素对磨损率和摩擦因数的影响,建立了磨损机制图,并分析了磨损与腐蚀的协同作用.研究表明:在不同滑移距离时,TAMZ钛合金的磨损率均随载荷增加先减小后增大,随着料浆浓度的增加而增大.摩擦因数随着载荷增加呈现增大趋势,且在蒸馏水中摩擦因数的变化比在Hank's模拟体液中平稳.当料浆浓度较低时,磨损机制为二体磨损机制;随着料浆浓度增加、载荷增大,磨损机制向混合磨损和三体磨损转变.随着载荷增加,腐蚀与磨损的交互作用增强,而在交互作用中,微磨损所起的作用比腐蚀所起的作用要大.     

采煤机滑靴激光熔覆铁镍基涂层的抗磨性能*

为提高采煤机滑靴在无油工况下的耐磨性,采用激光熔覆技术在45钢为基体上分别制备FeNiMo和FeNiMoSi涂层,并对其物相组成及硬度等进行分析。结果发现：制备的涂层结构致密,与基底保持了良好的冶金结合;FeNiMoSi涂层的平均硬度为438HV,分别约为基体（153HV）的2.8倍以及FeNiMo涂层（385HV）的1.1倍。通过往复式摩擦磨损试验机研究涂层的干摩擦磨损性能,并探讨其磨损机制。结果表明：随着载荷和滑动速度的增大,涂层的摩擦因数均呈现出减小的趋势;随着载荷的增大,涂层的磨损率逐渐升高;随着滑动速度的增大,FeNiMo涂层的磨损率出现先下降后上升的趋势,而FeNiMoSi涂层的磨损率则逐渐下降;涂层的磨损机制主要为磨粒磨损、塑性变形以及轻微的氧化磨损。总体来说,FeNiMoSi涂层相比FeNiMo涂层表现出更好的耐磨性能,这是因为涂层中Si元素的添加,不仅起到细晶强化作用,而且促进了FeSi金属间化合物相的生成。     

Dry sliding friction and casing wear behavior of PCD reinforced WC matrix composites

The friction and casing wear properties of PCD reinforced WC matrix composites were investigated using a cylinder-on-ring wear-testing machine against N80 casing steel counterface under dry sliding conditions. The results indicate that the friction and casing wear rate of PCD reinforced WC matrix composites are the lowest among the materials. As the applied load and sliding speed steadily increase, the friction coefficients of PCD reinforced WC matrix composites decrease. In addition, the casing wear rates increase with increasing load, but decline with sliding velocity. The dominant wear mechanism of the PCD composite is the micro-cutting wear, accompanied by adhesive wear.     

铜镍锡合金干滑动磨损行为研究*

大型装备上的铜镍锡合金工件常常工作在润滑不足或者无润滑的工况条件下,因此有必要研究铜镍锡材料在干摩擦下的性能。采用CEF-I型销-盘式磨损试验机对铜镍锡合金在不同载荷与转速条件下进行干滑动摩擦磨损试验,采用扫面电子显微镜、能谱仪和轮廓检测仪对磨损表面进行检测,研究铜镍锡合金的干滑动磨损行为,并探讨其磨损机制。结果表明：在转速一定时,平均摩擦因数随载荷增大总体呈波动下降趋势,铜镍锡合金试件磨损量先缓慢增加,在较高载荷下快速增加;在载荷一定时,平均摩擦因数随转速增大先增大后减小,铜镍锡合金试件磨损量总体呈先减小后增大趋势;随着载荷的增大,铜镍锡合金的磨损机制由轻微黏着和剥层磨损到明显的黏着和剥层磨损,再到严重的黏着和疲劳磨损,随着转速的增大,铜镍锡合金的磨损机制由磨粒磨损转变为黏着磨损再到剥层磨损。在较低载荷下,随着转速的增大,铜镍锡合金摩擦磨损性能保持很好的稳定性,因此铜镍锡合金适用在高转速较低载荷的干摩擦工况下。     

载流条件下的1Cr18Ni9Ti/浸金属碳摩擦磨损性能研究

在销-盘摩擦磨损试验机上试验了载荷、速度、电流对1Cr18Ni9Ti/浸金属碳对磨时的摩擦因数、磨损量及磨损形貌的影响。试验结果表明,载荷对1Cr18Ni9Ti/浸金属碳摩擦副的摩擦因数和销试样的磨损率有显著影响:载荷越大,摩擦因数越大,磨损率越低;摩擦因数、磨损率与速度的关系受载荷的制约。当低载时,以电流影响为主。销试样的磨损表面出现了粘着磨损,氧化磨损和电弧烧蚀。     

Sliding wear behavior of Fe-Al and Fe-Al/WC coatings prepared by high velocity arc spraying

A comparative study was carried out to investigate the microstructure and tribological behavior of Fe-Al and Fe-Al/WC iron aluminide based coatings against Si₃N₄ under dry sliding at room temperature using a pin-on-disc tribotester. The coatings were prepared by high velocity arc spraying (HVAS) and cored wires. The effect of normal load on friction coefficient and wear rate of the coatings was studied. The microstructure and the worn surfaces of the coatings were analysed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersion spectroscope (EDS). The results showed that, the main phases in both coatings were iron aluminide (Fe₃Al and FeAl) and α. WC/W₂C particles were embedded in the matrix of the composite coating. With adding WC hard particles, the Fe-Al/WC composite coating exhibited higher wear-resistance than Fe-Al coating. But the friction coefficient of both coatings showed little difference. As the load increased, the friction coefficient decreases slightly due to a rise of friction contact temperature and larger areas of oxide film formation on the worn surface, which act as a solid lubricant. Increasing load causes the maximum shear stress occurring at the deeper position below the surface, thereby aggravating the wear. The coating surface is subjected to alternately tensile stress and compression stress during sliding, and the predominant wear mechanism of the coatings appears to be delamination.     

PCrNiMo材料摩擦磨损特性研究

采用自制的销盘式干滑动摩擦磨损试验机，研究了不同硬度炮钢材料PCrNiMo自配副时的摩擦磨损特性。研究结果表明：材料的磨损率随着速度、载荷的增加而增大，摩擦因数随着速度、载荷的增加而减小；低速低载条件下，接触表面以磨粒磨损为主，而在高速、高载条件下，接触表面以粘着磨损形式为主。     

Vibration monitoring in sliding wear of plasma sprayed ceramics

Dry frictional contact between two surfaces, one made of plasma sprayed ceramic coatings of Al₂O₃ and Al₂O₃---TiO₂ combination and the other made of steel, is analyzed. The experiments were conducted using a pin-on-disc set-up in the load range of 5–35 N and for sliding distances up to 14 km. The interactions between friction, wear and vibrations due to influence of normal load, sliding speed and system dynamics are investigated in the present paper. Two vibration parameters of pin in the load direction (vertical) are monitored, namely the r.m.s. acceleration and the kurtosis, which seem to be influenced considerably by the wear process and indicate correlation with wear mechanisms taking place such as stick-slip and grain pull-out, as evidenced by scanning electron microscopy of worn surfaces. The study shows that a range of frequency is to be utilized for vibration monitoring to include natural frequencis of the system consisting of pin in contact with disc. This could be estimated by a standard impulse hammer test. The pin acceleration decreases with increase in load and sliding distance, but with respect to sliding speed, the vibration level intially decreases but increases beyond the sliding speed of 1.5 m s⁻¹. Among the three ceramic coatings, TiO₂ is found to be most wear resistant, exhibiting the lowest friction coefficient and a low vibration level. Variation in kurtosis with run-in wear indicates smoothing of Al₂O₃ due to grain pull out.     

Tribological properties of flame sprayed Fe–Ni–RE alloy coatings under reciprocating sliding

Fe–Ni–RE self-fluxing alloy powders were flame sprayed onto 1045 carbon steel. The tribological properties of Fe–Ni–RE alloy coatings under dry sliding against SAE52100 steel at ambient conditions were studied on an Optimol SRV oscillating friction and wear tester in a ball-on-disc contact configuration. Effects of load and sliding speed on tribological properties of the Fe–Ni–RE coatings were investigated. The worn surfaces of the Fe–Ni–RE alloy coatings were examined with a scanning electron microscopy(SEM) and an energy-dispersive spectroscopy(EDS). It was found that the Fe–Ni–RE alloy coatings had better wear resistance than the SAE52100 steel. An adhered oxide debris layer was formed on the worn surface in friction. Area of the friction layer varied with variety of sliding speed, but did not vary with load. The oxide layer contributed to decreased wear, but increased friction. Wear rate of the material increased with the load, but dramatically decreased at first and then slightly decreased the sliding speed. The friction coefficient of the material was 0.40-0.58, and decreased slightly with the load, but increased with sliding speed at first, and then tended to be a constant value. Wear mechanism of the coatings was oxidation wear and a large amount of counterpart material was transferred to the coatings.     

载荷和转速对HDPE多元复合材料摩擦学性能的影响

为改善高密度聚乙烯(HDPE)的力学性能、自润滑性和耐磨性,以HDPE为基体,通过填充六钛酸钾晶须(PTW)、聚四氟乙烯(PTFE)和滑石粉制备一种HDPE复合材料.在MMW-1型摩擦磨损试验机上测试复合材料在不同载荷和转速下的摩擦因数、磨损率,采用扫描电镜(SEM)分析磨痕形貌,探讨HDPE复合材料的摩擦磨损规律.结...