共查询到20条相似文献,搜索用时 46 毫秒
1.
2.
3.
4.
采用添加去极化剂的方法,对液体钽电解电容器工作电解质的配方进行改性,通过正交实验,研制出了一种新型的电解电容器电解质,用其装配成规格100V/100μF的液钽电容器,高低温性能测试结果表明,以CuS04为去极化剂,电容器的漏电流较小、容量变化小;以Fe2(S04)3作为去极化剂,电容器损耗较小,低温阻抗小,两种去极化剂都在一定程度上使电容器的高低温特性得到了改进. 相似文献
5.
采用聚四氟乙烯(PTEF)溶液对已形成钽氧化膜(Ta2O5)的Ta多孔体阳极表面进行预处理,在钽阳极微孔内形成具有许多通孔的非导电性高分子互穿网络结构,然后采用化学氧化聚合法,在互穿网络结构的通孔中原位聚合聚3,4-亚乙基二氧噻吩(PEDT)导电高分子聚合物,从而在Ta阳极体表面形成导电性高分子复合柔性固态电解质层。实验结果表明,采用20%体积浓度的PTEF水性分散液,原位聚合PEDT可以在钽阳极表面形成高机械强度的复合固态电解质层,用其制作的钽电解电容器,平均漏电流15μA,产品的平均等效串联电阻(ESR)值50mΩ。 相似文献
6.
研究在传统固体钽电解电容器多孔阳极体微孔内表面原位化学聚合制备PEDT导电聚合物薄膜的方法,通过对比所制有机固体钽电解电容器等效串联电阻(ESR)值的变化,讨论了采用化学原位聚合被膜过程中,受限空间里高分子链形成机理以及在受限条件和开放平面条件下被覆的聚合物薄膜导电性能的变化,采用SEM、AFM、X射线能谱对所制样品表面形貌变化以及多孔阳极体内部聚合物薄膜的被覆情况进行了研究。结果表明,在受限的空间里化学聚合反应生成的聚合物薄膜电导率会由于受限能的影响而降低,其影响程度相似于聚合溶液浓度的变化对聚合物薄膜电导率的影响。 相似文献
7.
8.
研究了导电聚合物PEDT作为阴极材料的有机片式固体钽电解电容器的制备工艺,通过调整隔离材料、掺杂剂等参数有效改善了有机片式固体钽电容器的性能.重点研究了阻隔剂、掺杂剂含量等参数对有机片式固体钽电容器电容、等效串联电阻、漏电流等性能的影响.结果表明,当隔离材料体积分数为0.5%~1.5%时,薄膜具有较好的耐压性能,电容器的漏电流较小(<5μA);当掺杂剂质量分数为1.5%~2%时,掺杂剂可以有效地进入PEDT主链进行掺杂,PEDT薄膜的电导率较高,从而使电容器获得较低的等效串联电阻. 相似文献
9.
研究了两种去极化剂对液体钽电容器高频电性能的影响.实验表明在100V/100μ F的液体钽电容器的电解质中加入去极化剂Fe2(SO4)3可以改善电容器在高频电路中的电性能,使之获得较低的ESR和较高的电容量C. 相似文献
10.
11.
A method is proposed for estimating the parameters of a mixture of exponential and Weibull distributions for which the accuracy of preliminary estimates obtained by graphical analysis is refined in accordance with the criterion of maximum likelihood. The efficiency of the proposed method is supported by the results of statistical modeling. 相似文献
12.
Liebert A Wabnitz H Grosenick D Möller M Macdonald R Rinneberg H 《Applied optics》2003,42(28):5785-5792
A novel method for the determination of the optical properties of tissue from time-domain measurements is presented. The data analysis is based on the evaluation of the first moment and the second centralized moment, i.e., the mean time of flight and the variance of the measured distribution of times of flight (DTOF) of photons injected by short (picosecond) laser pulses. Analytical expressions are derived for calculation of absorption and of reduced scattering coefficients from these moments by application of diffusion theory for infinite and semi-infinite homogeneous media. The proposed method was tested on experimental data obtained with phantoms, and results for absorption and reduced scattering coefficients obtained by the proposed method are compared with those obtained by fitting of the same data with analytical solutions of the diffusion equation. Furthermore, the accuracy of the moment analysis was investigated for a range of integration limits of the DTOF. The moment analysis may serve as a comparatively fast method for evaluating optical properties with sufficient accuracy and can be used, e.g., for on-line monitoring of optical properties of biological tissue. 相似文献
13.
14.
An approximate analytical expression is derived for the velocity of the front of the wave of change of boiling modes on a
rod and on a plate. The impact of the Thomson effect and of the heater orientation in the gravity field is included. Adequate
agreement is demonstrated between the derived relations and experimental data. 相似文献
15.
Conventional methods for summation of direct measurement errors are considered. Conditions under which these methods provide consistent results are stated. It is proposed to utilize for characteristic of the total error, its interval estimator or the half-sum of the value obtained by adding up its arithmetic and geometric random errors.Translated from Izmeritel'naya Tekhnika, No. 4, pp. 10–12, April, 1995. 相似文献
16.
由于空压机进气侧轴承箱蜗壳温度探头密封效果不好,使空压机及其后续管道受到油污染。后将温度探头的O形圈密封改为骨架油封,杜绝了轴承箱漏油问题。文章简介空压机的结构和技术参数,详细介绍了骨架油封的制作和优点。 相似文献
17.
M. M. Gadenin 《Inorganic Materials》2013,49(15):1352-1356
It is shown that conditions of attainment of marginal states in the material of structural components are formulated on the basis of analysis of force and deformation criteria of formation and development of destruction. The parameters of these criteria are data on types of structural materials, standard and special characteristics of their mechanical properties, structural forms of considered elements of the equipment, and their operating stress loading. In this case, the construction of a system of state equations for describing interrelation of current damage, external actions, and responses to them is based on the concept of calculating variations in properties of materials at all stages of the design life cycle. 相似文献
18.
V. T. Kornienko 《Strength of Materials》1991,23(7):760-765
The article suggests a method of evaluating the microstructural inhomogeneity of deformation of metals by modeling. The method includes the measurement of deformations of metal according to meshes of a dividing grid with small base and the calculation of the distribution parameters of microdeformations in model representation. It is shown that the modeling method makes it possible objectively to evaluate the microinhomogeneity of deformation of metals independently of the chosen mesh size of the dividing grid. New structural characteristics are introduced: the base and wave of variation expressing the degree of crumbling or amalgamation of metal grains by inhomogeneity of deformation.Translated from Problemy Prochnosti, No. 7, pp. 40–44, July, 1991. 相似文献
19.
20.
水三相点是开尔文热力学温度的唯一基准点,也是ITS-90国际温标重要的定义固定点。因此,水三相点不确定度分析对整个温标的建立、温度量值传递起着至关重要的作用。近3年来,中国计量科学研究院研制出一系列高质量的水三相点容器,加强了水三相点的研究,为不确定度的分析提供了更为可靠的实验依据。同时,不确定度的分析也是客观评价新研制容器性能的一个重要指标。因此,根据实验结果对新研制容器所复现的水三相点进行了不确定度评定。评定结果表明,其扩展不确定度为0.16mK(k=2.69,P=0.99)。 相似文献