压下率对6.5%Si电工钢温轧板织构的影响规律

6.5%Si电工钢是一种优异的软磁材料,织构对其磁性能影响很大。利用温轧工艺对6.5%Si电工钢热轧板进行不同压下率轧制,研究了温轧板织构随压下率的变化规律。实验结果显示,随着压下率的增大,{100}〈110〉、{110}〈100〉和γ纤维织构在薄板表层中的强度先增强后减弱,当压下率达到75%时,沿板厚方向形成3个组织区域:表层细晶粒区({110}〈100〉取向为主)、过渡层({111}〈110〉和{111}〈112〉变形晶粒区)和中心层(以拉长的γ纤维织构和{100}〈110〉取向晶粒为主),这种组织和织构不均性对后期织构的发展有重大影响。     

Fe-6.5%Si高硅钢的性能及制备技术

Fe-6.5%Si高硅钢是一种具有高磁导率、低矫顽力和低铁损等优异软磁性能的合金,但是其室温脆性和低的热加工性能严重影响了其在工业领域的应用。综述了Fe-6.5%Si高硅钢的性能,评述了合金的改性法、特殊轧制法、快速凝固法、沉积扩散法、粉末冶金法等制备工艺。     

冷轧压下率及初始高斯晶粒取向度对超薄取向硅钢织构演变与磁性能的影响

以不同高斯取向度的取向硅钢成品板为初始原料,采用一次冷轧法制备0.06~0.12mm厚的取向硅钢薄带。利用EBSD取向成像技术研究冷轧压下率以及初始高斯晶粒取向度对超薄取向硅钢织构演变与磁性能的影响。结果表明:随着冷轧压下率增大和厚度减小,退火后再结晶织构增强,当压下率为70%时,再结晶织构中RD∥〈001〉织构最锋锐,磁性能最佳;初始样品高斯取向度越高,制备的薄带样品磁性能越好;因此,生产高性能的取向硅钢薄带应选用初始高斯晶粒取向度较高的成品板。     

异步轧制对硅钢极薄带三次再结晶的影响

分别采用同步和异步轧制将成品工业取向硅钢板冷轧到0.045～0.10mm,然后在纯氢气热处理炉中进行三次再结晶高温退火,研究轧制工艺参数对取向硅钢极薄带织构和磁性能的影响,探索异步轧制对硅钢极薄带三次再结晶行为影响机理.结果表明,采用异步轧制取向硅钢极薄带的磁性能优于同步轧制的;硅钢极薄带厚度愈薄,磁性能愈好,三次再结晶发展得越完善.     

PVD法制备6.5%Si高硅钢过程合金磁性能演化机理研究

PVD法制备Fe-6.5%Si(质量分数,下同)高硅钢过程基片预处理工艺以及Si渗入对合金的软磁性能均有显著影响。采用磁损耗分离的方法剖析铁硅合金磁性变化的内在机理。采用四探针方法测试合金的电阻率;采用基于热分析仪(DSC)配置永磁场技术测量热重(TG)曲线确定合金的居里温度;采用振动样品磁强计(VSM)测定了材料的饱和质量磁矩;采用直流测试装置和硅钢测试仪测试合金的直流交流软磁性能。PVD法制备6.5%Si高硅钢最大磁导率达到16 400,相比于初始态3%低硅钢基片,铁损值降低40%~50%。     

轧制法制备低铁损高磁感6.4%(质量分数)硅钢及其织构演变

采用轧制法制备出具有低铁损高磁感0.23mm厚6.4%(质量分数)Si高硅钢。沿轧制方向的最终磁性能为B8=1.474 T,B50=1.714 T;P10/50=0.30W/kg,P15/50=0.88W/kg。利用X射线衍射及背散射电子衍射(EBSD)技术分析了高硅钢在轧制及退火过程中的织构演变过程。结果表明,通过采用大压下率热轧,确保热轧板次表层中产生更多的高斯织构,随后进行遗传;温轧板中粗大的晶粒有利于冷轧剪切带的形成;冷轧板经脱碳退火后生成强{210}〈001〉织构及次表层较强的高斯织构是在轧向上获得高磁感的原因,归因于其在{111}〈112〉冷轧形变晶粒内的剪切带优先形核并长大;最终退火后虽出现了随机取向,但以{310}〈001〉织构为代表的η织构得以保留并且增强,进一步提高了磁感。随着退火温度的升高及保温时间的延长,高硅钢薄板晶粒尺寸不断增大,铁损明显降低。     

Fe-6.5％Si/Fe73.5Cu1Nb3Si13.5B9纳米晶复合磁粉芯的制备及其软磁性能研究

采用Fe-6.5%Si粉末复合Fe_(73.5)Cu_1Nb_3Si_(13.5)B_9纳米晶粉末制备了复合磁粉芯,并讨论了Fe-6.5%Si粉末复合量对复合磁粉芯磁性能的影响。结果表明,随着Fe-6.5%Si粉末的添加量从20%增加到80%,复合磁粉芯的密度几乎从5.46g/cm3线性增加到6.01g/cm3。复合磁粉芯的有效磁导率在20～500kHz的频率范围内具有良好的稳定性。随着Fe-6.5%Si粉末添加量从20%增加到80%,复合磁粉芯的有效磁导率几乎从33.7线性增加到38.3。复合磁粉芯的损耗随着Fe-6.5%Si粉末添加量的增加而增加。复合磁粉芯的直流偏置性能随着Fe-6.5%Si粉末添加量的增加而逐渐降低。当直流偏置场为7.96kA/m时,随着Fe-6.5%Si粉末添加量从0增加到80%,复合磁粉芯直流偏置性能从79.6%逐渐下降到62.2%。     

再结晶及低温时效对Fe-6.5wt%Si薄板磁性能的影响

观察了高硅钢温轧板再结晶及低温时效过程中轧向和横向磁性能的差异及变化,通过取向分布函数、光学显微及X射线慢速扫描分析了织构、晶粒尺寸以及有序相的析出对铁损及不同磁场下磁感应强度的影响。结果表明,高硅钢虽然具有低的磁晶各向异性,织构仍是决定磁感值的关键因素,优化织构还可降低铁损。D03有序相的析出可降低饱和磁致伸缩系数,有益于降低低频铁损值,但其作用相比晶粒尺寸较小。退火后慢冷过程中依次发生B2及D03有序化,磁感B50的降低应是慢冷导致B2有序化及其有序度升高所致。等温时效过程以D03有序化为主,由于D03相在B2相中析出,时效过程中磁感没有变化。     

烧结助剂对反应热压烧结B4C基复合材料性能的影响

以微米级B₄C粉体为原料,通过与TiO₂葡萄糖原位反应制备TiB₂颗粒增韧B₄C复合材料。研究了烧结温度和烧结助剂对材料烧结行为及力学性能的影响。在1950℃反应热压下获得了相对密度为97.7%的TiB₂/B₄C复合材料,断裂韧性达到5.3 MPa·m1/2。添加Al₂O₃和Si烧结助剂后,分别在1950℃和1900℃ 获得了接近致密的(TiB_2,Al₂O₃)/B₄C和(TiB_2,SiC)/B₄C复合材料,断裂韧性分别提高到7.09和6.35 MPa·m1/2。显微组织分析表明,增韧作用主要来自残余应力引起的裂纹偏转。     

超薄取向硅钢组织及织构与磁性能的关系

本工作旨在探讨超薄取向硅钢组织及织构与磁性能的关系,并从加工工艺角度揭示如何减少不利于磁性能的组织和织构的产生。利用电子背散射衍射(EBSD)技术和X射线衍射(XRD)技术对两种磁性能不同的商业超薄取向硅钢带材的显微组织和织构进行对比分析,结果发现,二者组织、织构差异均比较明显。磁性能差的带材样品的组织尺寸不一,均匀性较差,η线织构(〈100〉//RD)所占比例偏低,非η线取向晶粒所占比例高且晶粒尺寸大,其取向特征主要表现为{210}〈001〉、{411}〈148〉及{111}〈110〉。这些不利组织的产生可能与轧制、退火工艺控制不当有关。因此,晶粒尺寸及η线取向晶粒所占比例的不同是造成两种带材性能差异的主要原因,在高性能取向硅钢超薄带材制备过程中,应精准控制轧制、退火制度等相关工艺,以避免非η线取向晶粒形成、长大。     

Mechanical properties of

The ultimate values for compressive strength, Young's modulus, and toughness of cylindrical specimens of unitary aspect ratios and uniform grain-size distributions were extrapolated for hydroxyapatite (HAP) to 70 MPa, 9.2 GPa, and 0.36 J cm-3, and for tricalcium phosphate (TCP), to 315 MPa, 21 GPa, and 2.34 J cm-3. For total volume porosities of 50%, the corresponding values were determined: for HAP, 9.3 MPa, 1.2 GPa, 0.042 J cm-3, for TCP, 13 MPa, 1.6 GP, 0.077 J cm-3. Porosities of HAP specimens ranged from 3%–50%; TCP from 10%–70%. Two pore-size distributions were employed. Exponential dependencies of the mechanical properties were found upon porosity (p0.0001). No differences in measured mechanical properties, as determined in compression, could be attributed to pore size. The superiority of TCP increases with density and suggests that a larger or more selective pore-size distribution could be effectively employed in TCP biological implants. This work also suggests the dominant role of secondary calcium phosphates in increasing compressive strengths. © 1999 Kluwer Academic Publishers     

Flexural properties and dynamic mechanical properties of glass fibre-epoxy composites

The viscoelastic behaviour of glass fibre (GF)-epoxy composites was studied by flexural tests and dynamic mechanical measurements. In relation, the influence of surface treatment of GF on viscoelastic behaviour was also examined. Using the results of flexural tests under a variety of constant temperature and strain rate, master curves of flexural strength () and flexural strain () were obtained for matrix epoxy and GF composites. The magnitudes of the master curves were different between matrix epoxy and GF composites. The fracture mode was influenced by temperature, strain rate, and G F surface treatment. The magnitude of storage modulus and effectiveness of adhesion at the GF-matrix interface were also influenced by GF surface treatment. Relationship between the results of flexural strain and loss modulus were considered for GF composites.     

Effective thermal properties of viscoelastic composites having field-dependent constituent properties

This study introduces a micromechanical model for predicting effective thermal properties (linear coefficient of thermal expansion and thermal conductivity) of viscoelastic composites having solid spherical particle reinforcements. A representative volume element (RVE) of the composites is modeled by a single particle embedded in the cubic matrix. Periodic boundary conditions are imposed to the RVE. The micromechanical model consists of four particle and matrix subcells. Micromechanical relations are formulated in terms of incremental average field quantities, i.e., stress, strain, heat flux and temperature gradient, in the subcells. Perfect bonds are assumed along the subcell’s interfaces. Stress and temperature-dependent viscoelastic constitutive models are used for the isotropic constituents in the micromechanical model. Thermal properties of the particle and matrix constituents are temperature dependent. The effective coefficient of thermal expansion is derived by satisfying displacement and traction continuity at the interfaces during thermo-viscoelastic deformations. This formulation leads to an effective time–temperature–stress-dependent coefficient of thermal expansion. The effective thermal conductivity is formulated by imposing heat flux and temperature continuity at the subcells’ interfaces. The effective thermal properties obtained from the micromechanical model are compared with analytical solutions and experimental data available in the literature. Finally, parametric studies are also performed to investigate the effects of nonlinear thermal and mechanical properties of each constituent on the overall thermal properties of the composite.     

Free-volume properties of epoxy composites and its relation to macrostructure properties

Some characteristics of epoxy composites are discussed based on the results of positron annihilation lifetime spectroscopy (PALS), electrical and mechanical measurements. The effect of different types and wt% of fillers such as aluminium oxide (Al₂O₃), titanium oxide (TiO₂) and silicon carbide (SiC) on the epoxy structure and hence free volume, physical, electrical, and mechanical properties is presented. The results showed that the electrical properties are improved at high wt% of filler, while mechanical properties are improved at low wt% of filler. Furthermore, a similar trend is observed for all fillers but with a systematic shift to high influence when Sic added to cured epoxy. On the other hand, adding SiC as a filler on epoxy improved the resistance to water absorption.The role of PALS as a sensitive probe for changes in microstructure of epoxy composites is confirmed during the correlation between the free-volume parameters and the other measurements.     

Thermodynamic properties of n-pentane

Specific volumes and isobaric heat capacity measurements are reported for n-pentane. The measurements were made in the liquid and vapor phases at temperatures ranging from the triple point (173 K) to the onset of dissociation temperature (700 K) and pressures up to 100 MPa including a wide region around the critical point. We are able to fit our data, as well as those of a number of other authors, to a single equation of state with 30 constants. This equation yields the density of n-pentane in the temperature range from 280 to 650 K at pressures up to 80 MPa and the caloric properties up to 500 K. Additional experimental investigations of the thermodynamic properties are required for temperatures above 500 K. Interpolating equations for the caloric properties on the saturated line and in the critical region are also presented.     

磺化改性对聚醚砜力学性能和抗凝血性能的影响

对磺化改性后聚醚砜的力学性能和抗凝血性能进行了测试 ,结果表明 :磺化改性后聚醚砜材料的力学性能有一些改善 ,抗凝血性能也有一定提高     

Piezoelectric properties,hysteresis behaviour and dielectric properties of PMN-PZT ceramics

Ferroelectric and piezoelectric properties ofxPb(Mg_1/3Nb_2/3)O₃−(1−x)Pb (Zr_0·55Ti_0·45)O₃ system have been investigated. X-ray diffraction patterns indicate rhombohedral and cubic structures. Maximum dielectric constant and piezoelectric properties are exhibited by 0·5–0·5 PMN-PZT composition.P _r is high in 0·6–0·4 PMN-PZT composition.     

Thermodynamic properties of nickel

This work reviews and discusses the data and information on the thermodynamic properties of nickel available through May 1984. These properties include heat capacity, enthalpy, enthalpy of transition and melting, vapor pressure, and enthalpy of vaporization. The recommended values for heat capacity cover the temperature range from 1 to 3200 K. The recommended values for enthalpy, entropy, Gibbs energy function, and vapor pressure cover the temperature range from 298.15 to 3200 K.     

Antifouling properties of hydrogels

Abstract

Marine sessile organisms easily adhere to submerged solids such as rocks, metals and plastics, but not to seaweeds and fishes, which are covered with soft and wet ‘hydrogel’. Inspired by this fact, we have studied long-term antifouling properties of hydrogels against marine sessile organisms. Hydrogels, especially those containing hydroxy group and sulfonic group, show excellent antifouling activity against barnacles both in laboratory assays and in the marine environment. The extreme low settlement on hydrogels in vitro and in vivo is mainly caused by antifouling properties against the barnacle cypris.     

Thermodynamic properties of titanium

This work reviews and discusses the data and information on the thermodynamic properties of titanium available through May 1984. These properties include heat capacity, enthalpy, enthalpy of transition and melting, vapor pressure, and enthalpy of vaporization. The recommended values for heat capacity cover the temperature range from 1 to 3800 K. The recommended values for enthalpy, entropy, Gibbs energy function, and vapor pressure cover the temperature range from 298.15 to 3800 K.