工艺参数及稳定剂抗坏血酸对电沉积NiFeW合金镀层的影响（英文）

为获得性能良好的镍铁钨合金镀层,研究了镀液pH值、温度、电流密度、稳定剂抗坏血酸浓度对镍铁钨合金镀层成分和镀层沉积速率、显微硬度的影响。结果表明:镀液pH值对镀层W含量和镀层沉积速率影响较大;镀液温度对镀层沉积速率、镀层成分和镀层硬度影响均较大;随抗坏血酸浓度增加,镀层沉积速率逐渐降低,镀层表面形貌更加粗糙。在镀液pH=4,温度60℃,电流密度4A/dm~2,抗坏血酸浓度3 g/L时,镀层沉积速率和镀层的显微硬度较高,表面光亮致密,耐蚀性好。     

工艺参数及稳定剂抗坏血酸对电沉积NiFeW合金的影响

为获得性能良好的镍铁钨合金镀层,研究了镀液pH 值、温度、电流密度、稳定剂抗坏血酸浓度对镍铁钨合金镀层成分和镀层沉积速率、显微硬度的影响。结果表明: 镀液pH 值对镀层W含量和镀层沉积速率影响较大;镀液温度对镀层沉积速率、镀层成分和镀层硬度影响均较大;随抗坏血酸浓度增加,镀层沉积速率逐渐降低,镀层表面形貌更加粗糙。在镀液pH = 4,温度60 ℃,电流密度4 A/dm2,抗坏血酸浓度3 g /L 时,镀层沉积速率和镀层的显微硬度较高,表面光亮致密,耐蚀性好。     

汽车轮毂用铝合金表面镍镀层的耐蚀性能研究

在汽车轮毂用的铝合金表面上电镀镍。研究镀液pH值、电流密度、镀液温度等因素对镀层耐蚀性能的影响。用线性扫描伏安法研究镍镀层在3.50%NaCl溶液中的耐蚀性能,用SEM和XRD表征了镍镀层的形貌和结构。结果表明,电镀的最佳工艺条件为:镀液pH为4.2,电流密度为30mA/cm2,镀液温度为58℃;在该条件下获得的镍镀层有很好的耐蚀性能,其结构为立方晶系。     

直流电沉积Ni-W-P镀层研究

采用直流电沉积法,在低碳钢表面成功沉积Ni-W-P镀层。应用X射线荧光(XRF)、扫描电子显微镜(SEM)、俄歇电子能谱(AES)、X射线衍射(XRD)仪等方法,研究电流密度、镀液pH值和镀液温度对Ni-W-P镀层成分、表面形貌和结构的影响。结果表明,电流密度和镀液pH值的变化对Ni-W-P镀层成分的影响很大,而电流密度、镀液pH值和温度对镀层厚度的影响较小。电流效率随着电流密度和镀液温度的增大分别降低和升高,而随着镀液pH值的变化,在pH=7.0时有极大值。镀液pH值对Ni-W-P镀层结构有较大影响,在pH=8.0时,镀层呈现明显的Ni(111)峰,此时镀层硬度达到极大值7130MPa。在此基础上,对Ni-W-P镀层的电沉积机制做了进一步探讨。     

工艺参数对连续碳纤维表面电磁搅拌化学镀镍的影响

目的解决连续碳纤维在镀覆过程中易出现黑心现象以及无法完全浸泡于镀液中的问题,制备镀层均匀的连续碳纤维镍镀层。方法引入外加电磁搅拌对连续碳纤维进行化学镀镍,研究了施镀时间、镀液温度、镀液pH值以及电磁搅拌转速对连续碳纤维表面微观形貌及镀层沉积速率的影响规律。结果当搅拌转速一定时,随着施镀时间、镀液温度、镀液pH值的不断增加,碳纤维表面镀层逐渐变得均匀完整,且镀层厚度逐渐增大。但当施镀时间超过20 min,镀液温度超过75℃,镀液pH值超过8时,镀层表面沉积了大量形状不一的胞状镍颗粒,形成粗糙的表面形貌。镀层的沉积速率随着镀液温度、镀液pH值的升高而增大。当搅拌转速由200 r/min增加到300 r/min时,镀层的沉积速率随着搅拌转速的增加而不断增大;当搅拌转速由300 r/min增加到400 r/min时,镀层的沉积速率随着搅拌转速的增加而不断减小。结论电磁搅拌辅助连续碳纤维化学镀镍的最佳施镀工艺参数为:施镀时间15~20 min,镀液温度75℃,镀液pH为8,搅拌转速200~250 r/min。采用此工艺参数能获得表面致密、均匀完整的镍镀层。     

工艺参数对石墨表面化学镀铜的影响

采用化学镀法在石墨增强体表面镀覆铜层,以改善石墨/Cu的润湿性。研究了镀液成分、石墨装载量、施镀温度对镀层的影响。结果表明:含锌粉的镀液成分简单不易分解、反应温度较低、环保无污染,且镀铜层均匀致密;石墨装载量为7.96 dm2/L时,铜镀覆层最致密;施镀温度为30℃时镀层最佳。     

MLCC三层镀中甲基磺酸镀锡体系工艺条件对锡镀层性能影响的研究

研究了片式多层陶瓷电容器(MLCC)三层镀中甲基磺酸镀纯锡体系pH值、温度、电流密度等工艺条件及杂质金属离子对镀液稳定性、镀层结构和性能等方面的影响。从电流效率、沉积速度及锡镀层表面的扫描电镜等方面,对比了不同pH值、温度、电流密度以及锡镀液中掺杂Cu2+、Ni2+后对锡镀层结构和性能的影响。研究结果给出了电镀工艺中最佳的pH值为3.5±0.2、温度为(23±2)℃、电流密度可以有较宽的范围,当镀液中掺有镍、铜等杂离子会对镀层产生负面影响,在给出的工艺参数下电镀,可以确保镀出最佳的纯锡镀层。     

Ni-W-B-WC复合镀层制备及性能研究

以镀层硬度和镀层外观为指标,研究电流密度、镀液中WC的含量、pH值、沉积温度对考察指标的影响.利用正交试验确定了电沉积最佳工艺条件:在超声振荡下,控制电流密度为7 A/cm2,施镀温度50℃,镀液中WC的含量为20 g/L,镀液pH值为5.0时,镀层硬度和镀层外观最佳,同时对Ni-W-B镀层、Ni-W-B-WC镀层的硬度、抗高温氧化性、耐腐蚀性能、表面形貌、镀层结构与成分等进行了测试.结果表明,Ni-W-B-WC复合镀层的综合性能要高于Ni-W-B合金镀层.     

化学镀法制备SiCp-Ni复合粉体

研究了酸性化学镀在SiCp陶瓷粉末表面涂覆Ni-P合金,考察了镀液的温度、pH值及粉末粒度对镀液稳定性和镀层性能的影响.结果表明,粉体越细,稳定施镀温度越低;合理选择工艺参数可使粒径从200μm～10μm的SiCp粉末得到均匀镀层;镀层P含量随pH值升高而降低,镀层结构为非晶态.     

环氧树脂表面化学镀镍层制备及结合力评价

采用化学镀的方法在环氧树脂表面制备镍镀层。观察了镀层表面和横截面形貌,研究了温度对镀层的表面形貌、沉积速率和结合力的影响,以及镀液pH值对镀层质量和沉积速率的影响,并对镀层与基体的结合力进行了评价。结果表明,环氧树脂化学镀镍的沉积速率随温度的升高而增大,但温度不宜太高,温度太高会增大镀层内部应力,降低镀层结合力。最佳施镀温度为35℃,镀液的最佳pH值为10,制备的镀层表面平整、均匀致密,镀层沉积速率为12μm/h,镀层与基体的结合力可达22.06 N。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

THERMODYNAMICS STUDY ON THE DECOMPOSITION OF CHROMITE WITH KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

INFLUENCE OF HEAT TREATMENT ON DAMPING BEHAVIOUR OF THE MAGNESIUM WROUGHT ALLOY AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.