碳纤维布加固已承受荷载的钢筋混凝土梁抗弯性能试验研究及抗弯承载力计算

进行了6根碳纤维布加固已承受荷载的钢筋混凝土梁和2根对比混凝土梁的抗弯性能试验研究,分析了碳纤维布加固已承受荷载的钢筋混凝土梁的破坏机理,研究了荷载历史对加固梁极限荷载的影响。试验结果表明,粘贴碳纤维布可以有效地提高加固梁的抗弯承载能力。无论荷载历史如何,只要梁承受的初始荷载相同,梁破坏时的极限荷载基本相同。梁端锚固对加固梁的极限荷载影响不明显。根据不同的破坏模式,提出了碳纤维布加固已承受荷载的钢筋混凝土梁的承载力计算方法,给出了工程实用计算公式。     

碳纤维布加固混凝土梁弯曲性能的试验研究

通过对4根矩形截面钢筋混凝土梁的静力加载试验,研究了碳纤维布对抗弯加固梁的破坏形态、刚度变化、极限承载力、变形能力和裂缝开展情况的影响,分析了碳纤维布粘贴层数和加固梁是否欲裂对碳纤维加固效果的影响.结果表明:碳纤维布可明显增强加固梁的极限承载力,改变加固梁的破坏形态,改善延性,延缓裂缝的发展,提高加固梁的整体刚度;同时碳纤维布粘贴层数越多,加固梁的极限承载力越大,但其提高程度并不与粘贴层数成正比;加固预裂梁后其极限承载力明显提高,但其延性降低.最后,针对现有的规范及理论研究结果,提出了抗弯加固梁的极限承载力计算公式,理论计算结果与试验值符合较好,满足工程实际要求.     

碳纤维布加固复合受力钢筋混凝土箱梁抗扭性能的非线性有限元分析

采用有限元方法对碳纤维布加固钢筋混凝土构件进行非线性分析,是对有限的试验研究的有效补充和进一步深入探讨。根据4根碳纤维布加固钢筋混凝土箱梁的试验研究结果,建立了合理的三维有限元模型,对碳纤维布加固钢筋混凝土箱梁在弯剪扭复合受力下的抗扭性能进行了非线性有限元分析。计算得到的扭矩-扭转角关系曲线、钢筋和碳纤维布的应变曲线以及界面粘接单元的恢复力曲线等与试验结果吻合较好,可以较好地模拟碳纤维布加固箱梁的受扭性能。进一步通过对7根数值梁的计算结果分析,提出碳纤维布加固钢筋混凝土箱梁在复合受力下的剪扭相关性符合直线方程。     

预应力碳纤维布材加固混凝土梁受弯性能非线性分析

根据平截面变形假定,考虑材料的非线性性质,用分级加应变的方法计算预应力碳纤维布加固的混凝土梁的荷载—挠度关系,得到的5根预应力碳纤维加固混凝土梁和4根非预应力加固混凝土梁的荷载-挠度曲线与试验结果吻合较好。并在此力学模型的基础上对预应力碳纤维布加固的受弯构件的二次受力性能进行了非线性分析,研究了碳纤维初始应变、截面高度、预应力大小对被加固梁受弯性能的影响。分析结果表明:预应力可有效发挥碳纤维高强性能,二次受力条件下预应力碳纤维布材的加固效果远好于非预应力碳纤维布材加固,可有效解决构件二次受力应力应变滞后问题。     

CFRP布端绕双杆自锁加固混凝土窄梁抗弯试验

为了抵抗粘贴碳纤维增强聚合物基复合材料（CFRP）加固钢筋混凝土结构中常见的剥离破坏,发明了将CFRP布端部以特定方式绕平行双杆实现自锁的方法。鉴于窄梁截面宽度有限,提出将CFRP布贴梁受拉底面布置后,用安装在梁侧面的双L形端锚装置固定双杆,形成侧锚底贴加固方案。完成了5根混凝土强度较低的矩形截面梁四点弯曲试验,其中4根采用上述锚固方式抗弯加固,检验了锚固效果,考察了CFRP布宽度及其沿全长与梁底面是否粘结对加固效果的影响。试验结果表明,采用本文方法进行加固后,端部剥离得以避免,中部剥离即使发生,或在无粘结加固梁受力后期,CFRP布仍能承担较大拉力,因此,极限荷载较对比梁有明显提高。比较而言,CFRP布与梁底有粘结时加固效果更好,CFRP布宽度加大也对提高承载力有益。     

混杂纤维布加固钢筋混凝土梁抗弯性能试验及理论研究

该文提出了碳/芳纶/玻璃三种纤维混杂思路,高强、高弹模碳纤维提高承载能力,高延伸率玻璃纤维改善延性,而芳纶纤维使应力从碳纤维向玻璃纤维平稳转移。通过对11根钢筋混凝土梁的抗弯试验,研究了不同混杂方式、混杂结构、纤维布层数对梁抗弯性能的影响。结果表明:如果应力转移不平稳,混杂纤维布将与混凝土发生局部剥离,导致混杂纤维布加固效果降低;在相同纤维布层数条件下,与单一碳纤维布加固梁相比,碳/芳纶/玻璃层间混杂纤维布加固梁的初裂、屈服、峰值和极限荷载分别降低了22%、12%、12%和16%,而位移延性系数提高了20%,表明碳/芳纶/玻璃层间混杂纤维布能够显著降低单一碳纤维布的脆性。在试验研究的基础上,采用弹塑性截面分析法计算了混杂纤维布加固梁的承载力,理论计算值与试验值吻合良好。     

纤维编织网增强地聚物砂浆加固钢筋混凝土梁受剪性能研究

为研究纤维编织网增强地聚物砂浆（TRGM）加固钢筋混凝土构件的可行性,首先通过双剪试验探讨了地聚物砂浆与碳纤维编织网在常温下和高温后的粘结性能,随后开展了地聚物砂浆粘贴不同层数（1层、2层、3层）碳纤维编织网抗剪加固钢筋混凝土梁的静载试验,并与未加固梁、环氧树脂粘贴碳纤维编织网抗剪加固混凝土梁进行了试验比较。试验结果表明,地聚物砂浆与碳纤维编织网的常温粘结强度达2.02 MPa,在温度不高于300℃时强度退化不显著;在未采取任何锚固措施的情况下,采用地聚物砂浆粘贴单层碳纤维编织网加固梁的抗剪承载力相比于未加固梁提高47.1%,提高幅度约为采用环氧树脂粘贴加固的一半;两层TRGM加固梁中的纤维作用发挥得最充分。最后,提出了TRGM抗剪加固梁斜截面承载力的简化计算模型,模型计算结果与试验结果吻合较好。     

钢筋混凝土梁力学试验研究

粘贴加固试验梁的加固效果随加固量的增加有明显提高,但是随着加固量的增加其结构承载力的提高是有限的。粘贴碳纤维布量与对试验梁承载力提高幅度不成线性比例关系,并且随着粘贴量的增加,加固材料(碳纤维布)不能充分发挥出其应有的强度。     

碳纤维布增强二次受力RC构件轴心抗拉试验研究

结合在役钢筋混凝土受拉构件承载力不足的特点,在8根钢筋混凝土构件轴拉试验基础上,对碳纤维布加固后预加载程度、持载程度对构件开裂荷载、极限荷载的影响进行分析,并提出受力构件的抗拉承载力计算式。研究表明,粘贴碳纤维布可以有效地提高二次受力钢筋混凝土轴拉构件极限承载力,限制裂缝宽度。所提公式与试验数据有较好的一致性,可供实际工程设计参考。该文研究成果对二次受力钢筋混凝土轴心受拉加固具有理论指导意义和工程应用价值。     

碳纤维布加固RC梁中粘结性能的非线性有限元分析

碳纤维布加固钢筋混凝土(RC)梁中,碳纤维布与梁底混凝土的剥离破坏使碳纤维布的强度不能得到充分发挥。分析碳纤维布与梁底混凝土的粘结应力,是研究碳纤维布加固剥离破坏承载力的基础问题。根据4根碳纤维布加固RC梁的试验研究结果,采用商业有限元程序MSC.Marc建立有限元模型,进行了非线性计算分析。通过分离总粘结应力中的局部粘结应力,得到粘结延伸长度范围内的锚固粘结应力分布,并结合试验数据对其分布规律进行了研究。根据分析和试验结果,引入了“有效锚固粘结长度”和“锚固粘结应力”的概念,给出了极限荷载下锚固粘结应力的计算建议。     

Structural behaviour of RC beams with external flexural and flexural–shear strengthening by FRP sheets

This paper presents experimental research on reinforced concrete (RC) beams with external flexural and flexural–shear strengthening by fibre reinforced polymer (FRP) sheets consisting of carbon FRP (CFRP) and glass FRP (GFRP). The work carried out has examined both the flexural and flexural–shear strengthening capacities of retrofitted RC beams and has indicated how different strengthening arrangements of CFRP and GFRP sheets affect behaviour of the RC beams strengthened. Research output shows that the flexural–shear strengthening arrangement is much more effective than the flexural one in enhancing the stiffness, the ultimate strength and hardening behaviour of the RC beam. In addition theoretical calculations are developed to estimate the bending and shear capacities of the beams tested, which are compared with the corresponding experimental results.     

Fatigue behaviour of the bond interface between carbon fibre‐reinforced polymer sheets and concrete

Externally bonded carbon fibre‐reinforced polymers (CFRPs) have been applied to retrofit and strengthen civil structures. In this study, four‐point bending beams were manufactured and tested to examine the fatigue behaviour of the CFRP–concrete interface. The results indicated that the specimens exhibited debonding failure in the concrete beneath the adhesive layer under static loading. However, when cyclic loads were imposed on the small beams, debonding failure may occur in the adhesive layer. Moreover, fitting expressions were proposed to predict the shear stress–slip relationship between the CFRP sheets and concrete and the flexural strength of the CFRP‐strengthened beams under static loads, and good agreement with the test data was obtained. Finally, a fatigue life prediction model was also presented to capture the fatigue life of the CFRP–concrete interface under cyclic loads. The calculation results showed that the fatigue strength of the CFRP–concrete bond interface was approximately 65% of the ultimate load capacity.     

预应力FRP加固混凝土结构技术研究与应用

介绍了笔者进行的预应力芳纶纤维布和碳纤维筋加固混凝土结构的一些主要研究成果,内容包括:预应力芳纶纤维布永久锚具的开发;预应力芳纶纤维布的应力松弛损失研究;预应力芳纶纤维布加固混凝土梁的受弯、受剪性能研究;温度对芳纶纤维布配套粘结材料的力学性能影响研究;体外预应力碳纤维筋局部加固混凝土梁的力学性能研究;碳纤维筋预应力粗纤维混凝土梁的抗震性能研究;预应力纤维布加固混凝土结构的工程应用等。     

CFRP布加固方案对RC梁剪切性能及尺寸效应影响分析EI北大核心CSCD

采用同时考虑混凝土材料非均质性、钢筋与混凝土之间的相互作用以及CFRP布与混凝土之间的相互作用影响的三维细观数值模拟方法,建立了CFRP布加固RC梁剪切破坏力学分析模型。在验证了细观数值方法合理性的基础上,设计并建立了12根CFRP布加固RC梁细观模型,探究相同CFRP配纤率(用布量)前提下,不同CFRP布加固方案对单调荷载作用下RC梁的剪切性能及尺寸效应的影响。结果表明:CFRP布应变分布与裂缝位置紧密相关,越靠近裂缝位置的CFRP布应变越大,提供的抗剪贡献越多;在CFRP配纤率一致的前提下,CFRP布宽度大厚度小的加固方案优于CFRP布厚度大宽度小的加固方案;CFRP布U型加固RC梁剪切强度存在尺寸效应现象,但相同CFRP配纤率下,不同CFRP布加固方案对名义抗剪强度尺寸效应的影响较小,可以忽略。     

Experimental investigations and verification of debonding strain of RHSC continuous beams strengthened in flexure with externally bonded FRPs

Although many in-situ RC beams are of continuous constructions, there has been very little research on the behavior of such beams with external reinforcement. This article presents an experimental program conducted to study the flexural behavior and redistribution of moment of reinforced high strength concrete (RHSC) continuous beams strengthened with carbon and glass-fiber-reinforced polymer (CFRP and GFRP) sheets. The program consists of six RHSC continuous (two-span) beams with overall dimensions equal to 250 × 150 × 6000 mm. One beam was not strengthened and was tested as a control beam. Five beams were strengthened with CFRP and GFRP in flexure along their sagging and hogging regions. The main parameters including type of FRP (GFRP or CFRP), the different ratios of CFRP sheet and effectiveness of end anchorage. The test results showed that the use of GFRP sheet in strengthening of continuous beam reduced loss in ductility and moment redistribution but it did not significantly increase the ultimate strength of them. The use of end anchorage in strengthened continuous beams increased the ultimate strength and moment redistribution. The moment enhancement ratio of the strengthened continuous beams was significantly higher than the ultimate load enhancement ratio in the same beam. Also existing international codes and model such as ACI, fib, JSCE, Teng and Toutanji for prediction of IC debonding strain or stress of strengthened continuous beams are verified. Verifications were carried out based on the test results in this research and the published literature on RC continuous beams strengthened with FRP.     

Experimental and analytical investigation of reinforced high strength concrete continuous beams strengthened with fiber reinforced polymer

Carbon and glass fiber reinforced polymer (CFRP and GFRP) are two materials suitable for strengthening the reinforced concrete (RC) beams. Although many in situ RC beams are of continuous constructions, there has been very limited research on the behavior of such beams with externally applied FRP laminate. In addition, most design guidelines were developed for simply supported beams with external FRP laminates. This paper presents an experimental program conducted to study the flexural behavior and redistribution in moment of reinforced high strength concrete (RHSC) continuous beams strengthened with CFRP and GFRP sheets. Test results showed that with increasing the number of CFRP sheet layers, the ultimate strength increases, while the ductility, moment redistribution, and ultimate strain of CFRP sheet decrease. Also, by using the GFRP sheet in strengthening the continuous beam reduced loss in ductility and moment redistribution but it did not significantly increase ultimate strength of beam. The moment enhancement ratio of the strengthened continuous beams was significantly higher than the ultimate load enhancement ratio in the same beam. An analytical model for moment–curvature and load capacity are developed and used for the tested continuous beams in current and other similar studies. The stress–strain curves of concrete, steel and FRP were considered as integrity model. Stress–strain model of concrete is extended from Oztekin et al.’s model by modifying the ultimate strain. Also, new parameters of equivalent stress block are obtained for flexural calculation of RHSC beams. Good agreement between experiment and prediction values is achieved.     

Flexural response predictions of reinforced concrete beams strengthened with prestressed CFRP plates

Existing experimental studies showed that the reinforced concrete (RC) beams strengthened with prestressed carbon fiber-reinforced polymer (CFRP) plates had three possible flexural failure modes (including the compression failure, tension failure and debonding failure) according to the CFRP reinforcement ratio. Theoretical formulas based on the compatibility of strains and equilibrium of forces were presented to predict the nominal flexural strength of strengthened beams under the three failure modes, respectively, and a limitation on the tensile strain level developed in the prestressed CFRP plate was proposed as the debonding failure occurred. In addition, the calculation methods for cracking moment, crack width and deflection of strengthened beams were provided with taking into account the contribution of prestressed CFRP plates. Experimental studies on five RC beams strengthened with prestressed CFRP plates and a nonlinear finite element parametric analysis were carried out to verify the proposed theoretical formulas. The available test results conducted by other researchers were also compared with the predicted values.     

Long-term behavior of existing low-strength reinforced concrete beams strengthened with carbon fiber composite sheets

This paper presents the results of an experimental study of the short- and long-term behavior of low-strength reinforced concrete (RC) beams strengthened with carbon fiber reinforced polymer (CFRP). A numerical analysis model was developed and verified for the calculation of the long-term deflection and maximum allowable long-term load of such RC beams. A parametric study was also conducted and it was found that the maximum allowable long-term load of a CFRP-strengthened beam was dominated by the deflection of RC beam when the cubic compressive strength of concrete was less than a certain value. For concrete of higher strength, the maximum allowable long-term load was dominated by the stress levels of the steel bars. It was also found that the yielding load of the strengthened beams increased significantly with areas strengthened by CFRP sheets and steel bars, while the maximum allowable long-term load only increased slightly.