Investigation on pumping oxygen characteristics of (Bi2O3)0.73(Y2O3)0.27 solid electrolyte

(Bi2O3)0.73(Y2O3)0.27 fine powders prepared by wet chemical precipitation method were cold isostatically pressed to form solid electrolyte tubes, and sintered at 900 ℃ for 10 h in the air. Their pumping oxygen characteristics in non-dehydrated Ar gas were investigated, where a ZrO2 (Y2O3 stabilized) oxygen sensor was used to measure the oxygen partial pressure Po2. The results showed that the Po2 value reached magnitudes of 1×10-20-1×10-10 Pa at the applied pumping oxygen voltage of 0.5 V, 1×10-37-1×10-27 Pa at 1.0 V and 1×10-53-1×10-47 Pa at 2.0 V within the temperature range from 550 to 650 ℃. Moreover, no cracks were found in the tested solid electrolyte tubes. Thus, the Bi2O3-Y2O3 system might be used in solid electrolyte oxygen pump for purifying gases.     

Growth of CeO2, Y2O3 Buffer Layers for YBCO Coated Conductor

The liquid citrate method was used to synthesize perovskite-type SrCe0.9 Y0.1O3-α powder. SrCe09Y01O3-α membranes were prepared from the powder by sintering at 1450℃ for 10 h. The reactions in the process of the heat treatment were studied by XRD and DSC/TG. The microstructure of the powder and the membrane was observed by SEM. The results indicate that the perovskite-type SrCe0.9Y0.1 O3-α can be synthesized at 1100℃. The particle size of the synthesized SrCe0.9Y0.1O3-α powder is less than 1μm. The powder can be densified at 1450℃.     

Catalytic Reduction of SO2 on CeO2-La2O3 Rare Earth Mixed Compounds

Adding rare earth oxide CeO2 with variable valences to La2O3 formed a mixture of rare earth oxides. By means of dipping CeO2, La2O3 and their mixture, whose carriers were all γ-Al2O3, were used as the catalyst for the reduction of SO2 by CO. The activation process of this catalyst and the impact of temperature and reactant concentration on the activation process were investigated. Using X-ray diffraction, the structure characteristics of catalyst before and after reaction were analyzed to reveal the change of phase structure. The result shows that the rare earth oxide mixtures composing of CeO2 and La2O3, as the catalyst for the reduction of SO2 by CO, diminish activation temperature 50～100℃ less and have higher activity than a single oxide CeO2 or La2O3. The reason possibl is that La2O3 goes into in the lattice of CeO2 to form solid phase complex CeO2-La2O3 and increases the capability of CeO2-La2O3/γ-Al2O3 catalyst to store oxygen, which supplies the redox of CeO2 reaction with a better condition. At the same time, elemental sulfur formed in the redox reaction impels La203 to be transformed to activation phase La2O2S in a lower temperature, which can be explained with the synergism between redox reaction and COS intermediate mechanism reaction.     

Optical Spectroscopy of Er^3＋ and Er^3＋/Yb^3＋ Co-doped Bi2O3-GeO2-B2O3-ZnO Glasses

The （60 - x）Bi2O3 - xGeO2-30B2O3-10ZnO （x = 5, 10, 20, 30 molar percent） glasses doped with Er^3＋ and Er^3＋/Yb^3＋ were fabricated using the melting method. The thermal stability of the glasses was studied with their DTA curves. The results show that the difference between the glass transition temperature and the crystallization onset temperature increases with the increase of GeO2 content, indicating that the thermal stability of the glass has become better. The absorption spectra were recorded and the stimulated emission cross sections were calculated using the McCumber theory. The Ω2, O4, and Ω6 parameters,the transition probability, the radiative lifetime, and the fluorescence branch ratio of Er^3＋ for optical transition were calculated from their absorption spectra in terms of reduced matrix U^（t）（λ = 2, 4, 6） character for optical transitions. The infrared emission of Er^3＋ was measured upon excitation with 970 nm light and the full width at half-maximum （FWHM） was estimated from the emission spectra. The pumping efficiency and the intensity of the emission at the 1.54 μm band of Er^3＋ were enhanced considerably by co-doping Yb^3＋ .     

Study on UV Excitation Properties of Eu^3＋ at S6 Site in Bulk and Nanocrystalline Cubic Y2O3

Increases of emission intensities for Eu^3 at the S6 site relative to that at the C2 site were observed as UV excitation wavelength decreases from 300 nm to 200 nm in both bulk and nanocrystalline cubic Y2O3:Eu^3 . Decomposition of excitation spectra shows that the charge transfer band of Eu^3 at the S6 site lies in the high-energy side of that at the C2 site, resulting in that the energy transfer from the host prefers to the S6 site. Detailed emission and excitation spectral characteristics were analyzed and discussed. In addition, spectral red-shift were found in both charge transfer bands in nanocrystalline Y2O3: Eu^3 compared to the bulk material. The number ratio of S6 sites to C2 sites is also smaller in nanocrystalline Y2O3:Eu^3 than that in the bulk one.     

Solid Phase Synthetic Reaction of Sodium Pyroxene for Na2 CO3-Fe （OH） 3-H2 SiO3 System

In order to explore synthetic method of pure sodium pyroxene,the pure chemical reagents of Na2CO3,Fe(OH)3 and H2SiO3were used as raw materials,and the possible solid phase reactions for Na2CO3-Fe(OH)3-H2SiO3system in heating process had been studied by means of differential thermal analysis(DTA)and X-ray diffraction(XRD). The influencing factors of sodium pyroxene(NaFeSi2O6)synthetic reaction,such as sintering temperature and holding time,had also been studied.The results show that sodium pyroxene can be largely synthesized at 737℃;it is helpful for synthesis of sodium pyroxene to increase sintering temperature appropriately,and the best temperature should be controlled at 900℃or so,because it will melt and decompose at temperatures higher than 900℃.In those influencing factors of sodium pyroxene synthesis the most important is temperature.The results will be helpful for providing pure NaFeSi2O6for further research on the formation of SFCA for NaFeSi2O6-KAlSi2O3-CaO-Fe2O3-CaF2 system in the sintering process of Bayan-obo iron ore.     

Defect structure and electrical properties of LaSr_3Fe_3O_(10-δ)

As a mixed conductor,LaSr3Fe3O10-δ with triple layer perovskite intergrowth structure can be used as an oxygen separation membrane material and cathode material in solid oxide fuell cells.LaSr3Fe3O10-δ was synthesized via citrate acid route.Iodine titration method was used to determine the average valence of transition metal Fe and oxygen nonstoichiometry δ.Conductivities of LaSr3Fe3O10-δ were measured in the oxygen partial pressure range from 10-2×105 to 1×105 Pa,by Ac four probe method.Seebeck coefficient...     

Low-temperature electrochemical synthesis and characterization of ultrafine Y（OH）_3 and Y_2O_3 nanoparticles

Ultrafine Y(OH)3 nanoparticles were successfully deposited from an additive-free 0.005 mol/L YCl3 low-temperature bath on the steel cathode at the current density of 0.5 mA/cm2 and bath temperature of 10 oC. Heat treatment of the prepared Y(OH)3 nanoparticles at 600 oC in air led to the formation of Y2O3 nanoparticles. Thermal behavior and phase transformation during the heat treatment of Y(OH)3 were investigated by differential scanning calorimetry (DSC) and thermogramimetric analysis (TGA). The morphologies, crystal structures and compositions of the prepared materials were examined by means of scanning and transmission electron microscopy (SEM and TEM) as well as X-ray diffraction (XRD) and FT-IR spectroscopy. The results showed that the prepared Y(OH)3 nanoparticles was essentially amorphous and composed of well dispersed ultrafine particles with size of 4 nm. After heat treatment, the obtained oxide product was well crystallized cubic phase of Y2O3 nanoparticles with the grain size of around 5 nm. It was concluded that low-temperature cathodic electrodeposition offered a facile and feasible way for preparation of ultrafine Y(OH)3 and Y2O3 nanoparticles.     

Structures and oxygen storage capacities of CeO2-ZrO2-Al2O3 ternary oxides prepared by a green route： supercritical anti-solvent precipitation

CeO2-ZrO2-Al2O3 ternary oxides were successfully prepared by a green route of supercritical anti-solvent precipitation with supercritical CO2 as anti-solvent and methanol as solvent.The structures and oxygen storage capacities of these ternary oxides were characterized by XRD,Raman spectra and oxygen storage capacity measurements.It was found that Al 3+ and Zr 4+ inserted into CeO2 lattice,forming CeO2-ZrO2-Al2O3 solid solution.The concentration of aluminium isopropoxide in the solution affected the concentration of oxygen vacancy and the distortion of oxygen sublattice which were responsible for the oxygen storage capacity.The rapidest oxygen uptake/release rate and maximum total oxygen storage capacity(122.0 mmolO2/molCeO2)were obtained with the aluminium isopropoxide concentration at 0.2 wt.% in the solution.     

Study on Sulfation of CeO2/γ-Al2O3 Sorbent in Simulated Flue Gas

It is well known that sulfur dioxide(SO2) , morethan50%of which arise fromcombustion of fossil fu-els ,are precursors of acidrain andtheir emission pos-es a global threat tothe atmosphere .Environmental a-gencies have ,therefore ,regulated emissions of SO…     

Phase control of magnetron sputtering deposited Gd2O3 thin films as high-κ gate dielectrics

Gd2O3 thin films as high-κ gate dielectrics were deposited directly on Si（001） substrates by magnetron sputtering at a pressure of 1.3 Pa and different temperatures. X-ray diffraction results revealed that all the films grown from 450 to 570 ℃ were crystalline, and the Gd2O3 thin films consisted of a mixture of cubic and monoclinic phases. The growth temperature was a critical parameter for the phase constituents and their relative amount. Low temperature was favorable for the formation of cubic phase while higher temperature gave rise to more monoclinic phase. All the Gd2O3 thin films grown from different temperatures exhibited acceptable electrical properties, such as low leakage current density （JL） of 10-5 A/cm^2 at zero bias with capacitance equivalent SiO2 thickness in the range of 6-13 nm. Through the comparison between films grown at 450 and 570 ℃, the existence of monoclinic phase caused an increase in JL by nearly one order of magnitude and a reduction of effective dielectric constant from 17 to 9.     

Paramagnetic Anisotropy of CdGd2（WO4） 4-δ Single Crystal

CdGd2 （WO4）4 -δ single crystal was grown using the Czochralski＇s method. The crystal structure was tetragonal seheelite with lattice parameters a = b = 0.5203 nm and c = 1. 1359 nm. There were vacancies of （WO4）^2- , therefore, there were some Gd^2＋ ions. Langevin paramagnetism and anisotropy were observed from the δ-T curves at room temperature. The susceptibility X//was 3.5018×10^-3, and X⊥ was 3.4403× 10^-2. The anisotropy was also observed in the electron spin resonance （ESR） experiments. The anisotropic Land6 factors were g//= 2. 1333 and g~ = 2. 8411. The direction of easy magnetization was in the α-b plane. Anisotropic paramagnetic Curie constants C//and C⊥ were not only related to macroscopic a that was observed through the experiment, but were also related to J⊥ and J//, which were the microscopic quantum numbers of the Gd^2＋ and Gd^3｜ ions. Based on the detailed analyses, the proportion of 36.8% of Gd^3＋ ions to 63.2% of Gd^2＋ ions in the Gd ions of the CdGd2（WO4）4-δ crystal was calculated, and δ was 0.638 in the single crystal.     

Characterization of Y2O2S： Eu^3＋, Mg^2＋, Ti^4＋ Long-Lasting Phosphor Synthesized by Flux Method

Long-lasting phosphor Y₂O₂S: Eu³⁺, Mg²⁺, Ti⁴⁺ was synthesized by a flux method and their luminescence properties were investigated. The result indicates that the unit cell parameter c is linearly increased with the increase of Eu₂O₃ content in Y₂O₂S: Eu_x³⁺ (0.01 ≤ x ≤ 0.10). On the other hand, the change of unit cell parameter a is not linear dependence. In the Y₂O₂S: Eu³⁺ crystal structure, Eu³⁺ ions only replaced Y³⁺ ions' places in which it posited center position of c axis. With the increase of Eu₂O₃ content, the position of the strongest emission peak changed from 540 nm (⁵D₁→⁷F₂ transition) to 626 nm (⁵D₀→⁷F₂ transition), and the maximum intensity was obtained when x = 0.09 in Y₂O₂S: Eu_x³⁺ (0.01 ≤ x ≤ 0.10). This is due to the environment of trivalent europium in the crystal structure of Y₂O₂S. Doping with Mg²⁺ or Ti⁴⁺ ions alone cannot get the good long-lasting afterglow effect, whereas co-doping with Mg²⁺ and Ti⁴⁺ ions and excited with 365 nm ultraviolet light, a strong thermoluminesence peak appeared, red and orange long-lasting phosphorescence (LLP) was also observed and the phosphorescence lasted nearly 3 h in the light perception of the dark-adapted human eye (0.32 mcd · m⁻²). Thus the LLP mechanism was analyzed.     

Vacuum ultraviolet excited photoluminescence properties of Gd2O2CO3：Eu^3＋ phosphor

The Gd2O2CO3：Eu^3＋ with type-Ⅱ structure phosphor was successfully synthesized via flux method at 400 ℃ and their photoluminescence properties in vacuum ultraviolet （VUV） region were examined. The broad and strong excitation bands in the range of 153-205 nm owing to the CO3^2- host absorption and charge transfer （CT） of Gd^3＋-O2^- were observed for Gd2O2CO3：Eu^3＋. Under 172 nm excitation, Gd2O2CO3：Eu^3＋ exhibited strong red emission with good color purity, indicating Eu^3＋ ions located at low symmetry sites and the chromaticity coordination of luminescence for Gd2O2CO3：Eu^3＋ was （x=0.652, y=0.345）. The photoluminescence quenching concentration of Eu^3＋ excited by 172 nm for Gd2O2CO3：Eu^3＋ was about 5%. Gd2O2CO3：Eu^3＋ would be a potential VUV-excited red phosphor applied in mercury-free fluorescent lamps.     

Thermochemical Study on Ternary Solid Complex of La(Gly)2 (Ala)3 Cl3 ·2H2O (s)

The complex of lanthanum chloride with Glycine and Alanine, La(Gly)₂(Ala)₃Cl₃ · 2H₂O, was synthesized and characterized by IR, elementary analysis, thermogravimetric analysis, and chemical analysis. The dissolution enthalpies of LaCl₃ · 7H₂O(s), 2Gly(s) + 3Ala(s) and La(Gly)₂(Ala)₃Cl₃ · 2H₂O(s) were determined in 2 mol · L⁻¹ HCl by a solution-reaction isoperibol calorimeter. By designing a thermochemical cycle in terms of Hess' Law and through calculation, the reaction enthalpy of lanthanum chloride seven-hydrate with Glycine and Alanine was obtained: Δ_rH^θ_m(298.15 K) = (29.652 ± 0.504) kJ · mol⁻¹, and the standard enthalpy of formation of La(Gly)₂(Ala)₃Cl₃ · 2H₂O(s) Δ_fH^θ_m[La(Gly)₂ (Ala)₃Cl₃ · 2H₂O, s, 298.15 K] = −4467.6 ± 8.3 kJ · mol⁻¹.     

Removal of molybdenum from MnSO4 solution with freshly precipitated “nascent” Mn3O4

The scavenging of molybdenum from MnSO₄ solution with freshly precipitated “nascent” Mn₃O₄ is reported. Firstly, nascent Mn₃O₄ was prepared from MnSO₄ solution by adding NaOH and aerating. The aeration time had a significant influence on the preparation of nascent Mn₃O₄, but other factors such as pH and ageing time had little effect. SEM, XRD, particle size and surface area analysis were used to characterize nascent Mn₃O₄. A study was then carried out on the effects of time, concentration of Mn, initial pH, temperature and dosage of nascent Mn₃O₄ on the adsorption of Mo from MnSO₄ solution. The results showed that the concentration of Mo in 70–200 g L^− 1 MnSO₄ at pH 1–3 could be reduced from about 1 mg L^− 1 to less than 0.015 mg L^− 1 in 30 min at 80 °C by the addition of about 0.3 g L^− 1 nascent Mn₃O₄ in suspension. Accordingly, the removal capacity of nascent Mn₃O₄ can reach 4.42 mg Mo/g Mn₃O₄. This Mo removal exceeds the requirement for special electrolytic MnO₂ used in the production of alkaline zinc–manganese batteries.     

Synthesis of ZrO2-HfO2-Y2O3-Sc2O3 Nano-Particles by Sol-Gel Technique in Aqueous Solution of Alcohol

Zirconium dioxide is a significant material withgood physicochemical characteristics . It is used inmanyfields such as energysources ,material and envi-ronment . Cubic phase zirconium dioxide doped withyttria (YSZ) is alreadyin wide use in solid oxygenfu-…     

Stability of 3CaO · Al2O3 · 6H2O in KOH + K2CO3 + H2O system for chromate production

In the novel clean chromate production process, the alkali liquor recycled to decompose the chromite ore mainly consists of KOH and K₂CO₃ which accumulates aluminium impurity and affects the quality of the product greatly. Aluminium impurity can be removed by adding CaO to precipitate as 3CaO · Al₂O₃ · 6H₂O (C₃AH₆). A study of the effects of various parameters, such as KOH concentration, K₂CO₃ concentration and temperature on the behaviour of C₃AH₆ show that C₃AH₆ is decomposed to 3CaO · Al₂O₃ · CaCO₃ · 11H₂O and CaCO₃ below 150 g L^− 1 KOH, and decomposed to Ca(OH)₂ above 150 g L^− 1 KOH. With K₂CO₃ concentration increasing, C₃AH₆ decomposes significantly, which results in more CaCO₃ or 3CaO · Al₂O₃ · CaCO₃ · 11H₂O produced. Temperature has a large positive effect on the decomposition of C₃AH₆ at 45 g L^− 1 KOH but has no significant effect at 150 g L^− 1 KOH. The optimal condition for removing aluminium impurity in the KOH + K₂CO₃ + H₂O system is 150 g L^− 1 KOH, 50 g L^− 1 K₂CO₃ and 80 °C.     

Electrochemical Behavior of Dissolved Fe2O3 in Molten CaCl2-KF

The electrochemical behavior of dissolved Fe2O2 in 82.5CaCl2-17.5KF （mole percent, %） was studied using cy clic voltammetry, chronoamperometry, and galvanostatic electrolysis at 827 ℃, and the deposits were characterized by XRD and SEM. Pure iron was deposited on a rotating cylinder （210 r/min） with a cell voltage less than -- 1.0 V. Deposition rate was controlled by diffusion on a molybdenum electrode. The diffusion coefficient of iron species Fe（ Ⅲ ） in the melt at 827 ℃ was found to be 9.7×10^-5 cm^2/s.