非掺半绝缘磷化铟晶片的制备及其均匀性

对高温退火非掺磷化铟(InP)制备的半绝缘晶片的电学性质和均匀性进行了研究.非掺低阻N型磷化铟晶片分别在纯磷气氛和磷化铁气氛下进行930℃、80h退火均可获得半绝缘材料.但在这两种条件下制备的两种50mm半绝缘晶片却呈现出不同的电学性质和均匀性.纯磷气氛下制备的磷化铟片的电阻率和迁移率分别达到106Ω·cm和1800cm2/(V·s);而在磷化铁气氛下退火获得的半绝缘片的电阻率和迁移率分别高达107Ω*cm和3000cm2/(V*s)以上.对这两种半绝缘片和原生掺铁磷化铟半绝缘片的PL-Mapping结果进一步比较表明:在磷化铁气氛下退火获得的半绝缘材料的均匀性最好,而在纯磷气氛下制备的半绝缘磷化铟的均匀性较差.     

非掺半绝缘磷化铟晶片的制备及其均匀性

对高温退火非掺磷化铟(InP)制备的半绝缘晶片的电学性质和均匀性进行了研究.非掺低阻N型磷化铟晶片分别在纯磷气氛和磷化铁气氛下进行930℃、80h退火均可获得半绝缘材料.但在这两种条件下制备的两种50mm半绝缘晶片却呈现出不同的电学性质和均匀性.纯磷气氛下制备的磷化铟片的电阻率和迁移率分别达到106Ω·cm和1800cm2/(V·s);而在磷化铁气氛下退火获得的半绝缘片的电阻率和迁移率分别高达107Ω*cm和3000cm2/(V*s)以上.对这两种半绝缘片和原生掺铁磷化铟半绝缘片的PL-Mapping结果进一步比较表明:在磷化铁气氛下退火获得的半绝缘材料的均匀性最好,而在纯磷气氛下制备的半绝缘磷化铟的均匀性较差.     

高温退火非掺杂磷化铟制备半绝缘材料

对液封直拉(LEC)非掺磷化铟(InP)进行930℃ 80h的退火可重复制备直径为50和75mm的半绝缘 (SI)衬底.退火是在密封的石英管内纯磷(PP)或磷化铁(IP)两种气氛下进行的.测试结果表明IP-SI InP衬底具有很好的电学性质和均匀性,而PP-SI的均匀性和电学参数都很差.在IP-SI样品的PL谱中出现与深缺陷有关的荧光峰.光激电流谱的测量结果表明:在IP气氛下退火获得的半绝缘磷化铟中的缺陷明显比PP-SI磷化铟的要少.并对退火后磷化铟中形成缺陷的机理进行了探讨.     

高温退火非掺杂磷化铟制备半绝缘材料

对液封直拉(LEC)非掺磷化铟(InP)进行930℃ 80h的退火可重复制备直径为50和75mm的半绝缘 (SI)衬底.退火是在密封的石英管内纯磷(PP)或磷化铁(IP)两种气氛下进行的.测试结果表明IP-SI InP衬底具有很好的电学性质和均匀性,而PP-SI的均匀性和电学参数都很差.在IP-SI样品的PL谱中出现与深缺陷有关的荧光峰.光激电流谱的测量结果表明:在IP气氛下退火获得的半绝缘磷化铟中的缺陷明显比PP-SI磷化铟的要少.并对退火后磷化铟中形成缺陷的机理进行了探讨.     

退火对LEC SI GaAs单晶性能的影响

本文报道了退火对非掺LEC SI GaAs晶片的电学性能和均匀性的影响。在850℃以上退火,晶片横截面上的平均迁移率由原生晶体的2.64×10~3cm~2/V·s提高到5.72×10`3cm~2/V·s,其中某些测量点达6.68×10~3cm~2/V·s,横向不均匀性由32％减少到6％,电阻率不均匀性由30％减少到10％。观察到晶片退火时间过长,性能反而下降。 基于上述实验结果,对退火改善晶体性能的机理进行了分析和讨论。     

空位和填隙缺陷对半绝缘InP单晶性质的影响

利用电学测试、正电子寿命谱和X射线衍射技术研究了原生和退火处理后InP单晶的空位和填隙缺陷.在原生掺铁半绝缘InP单晶中含有空位缺陷,这些空位产生深能级电学补偿缺陷,降低材料的电学性能.经高温磷化铁气氛下退火处理非掺InP制备的半绝缘材料,空位被充分抑制,却含有一定浓度填隙缺陷.根据实验结果分析了填隙和空位缺陷对掺铁半绝缘InP单晶材料电学性质和热稳定性的影响.     

空位和填隙缺陷对半绝缘InP单晶性质的影响

利用电学测试、正电子寿命谱和X射线衍射技术研究了原生和退火处理后InP单晶的空位和填隙缺陷.在原生掺铁半绝缘InP单晶中含有空位缺陷,这些空位产生深能级电学补偿缺陷,降低材料的电学性能.经高温磷化铁气氛下退火处理非掺InP制备的半绝缘材料,空位被充分抑制,却含有一定浓度填隙缺陷.根据实验结果分析了填隙和空位缺陷对掺铁半绝缘InP单晶材料电学性质和热稳定性的影响.     

退火对掺钒半绝缘4H-SiC晶片质量影响的研究

通过物理气相传输(PVT)法成功地生长出直径大于7.62 cm的掺钒半绝缘4H-SiC晶体。抛光后的掺钒半绝缘4H-SiC晶片在真空且温度1 600℃～2 000℃条件下进行退火处理,利用高分辨X-ray衍射仪、显微拉曼光谱仪、非接触电阻率测试仪和应力仪对退火前后的晶片进行了测试与分析,研究了退火工艺对掺钒半绝缘4H-SiC晶片应力的影响,并且得到了合适的退火工艺。结果表明:合适的退火处理有利于进一步提高晶片的质量。     

N-Al共掺ZnO薄膜的p型传导特性

利用直流反应磁控溅射技术制得N-Al共掺的p型ZnO薄膜，N2O为生长气氛．利用X射线衍射（XRD），Hall实验，X射线光电子能谱（XPS）和光学透射谱对共掺ZnO薄膜的性能进行研究．结果表明，薄膜中Al的存在显著提高了N的掺杂量，N以N-Al键的形式存在．N-Al共掺ZnO薄膜具有优良的p型传导特性.当Al含量为0.15wt%时，共掺ZnO薄膜的电学性能取得最优值，载流子浓度为2.52e17cm－3，电阻率为57.3Ω·cm，Hall迁移率为0.43cm2/(V·s)．N-Al共掺p型ZnO薄膜具有高度c轴取向，在可见光区域透射率高达90%．     

半绝缘InP中Si~++P~+双注入的电学特性

研究了在200℃热靶条件下经Si~+单注入和S~++P~+双注入的半绝缘InP常规热退火和快速热退火后的电学特性。热退火后,双注入样品中的电学性能优于单注入样品。采用快速热退火后,双注入的效果更加显著。Si~+150keV,5×10~(14)cm~(-2)+P~+160keV,5×10~(14)cm~(-2)双注入样品经850℃、5秒快速效退火后,最高载流子浓度达2.6×10~(19)cm~(-3),平均迁移率为890cm~2/V·s。     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Nanoimprint Lithography -A Next Generation High Volume Lithography Technique

IntroductionNanoimprint Lithography is a well-acknowl-edged low cost, high resolution, large area pattern-ing process. It includes the most promising methods,high-pressure hot embossing lithography (HEL) [2],UV-cured imprinting (UV-NIL) [3] and micro contactprinting (m-CP, MCP) [4]. Curing of the imprintedstructures is either done by subsequent UV-lightexposure in the case of UV-NIL or by cooling downbelow the glass transition temperature of the ther-moplastic material in case of HEL…     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

Influence of PVK ： NPB hole transporting layer on the characteristics of organic light-emitting devices

A doping system consisting of NPB and PVK is employed as a composite hole transporting layer （CHTL）. By adjusting the component ratio of the doping system, a series of devices with different concentration proportion of PVK ： NPB are constracted. The result shows that doping concentration of NPB enhances the competence of hole transporting ability, and modifies the recombination region of charge as well as affects the surface morphology of doped film. Optimum device with a maximum brightness of 7852 cd/m^2 and a power efficiency of 1.75 lm/W has been obtained by choosing a concentration proportion of PVK ： NPB at 1：3.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.     

Analysis of error performance on Turbo coded FDPIM

Due to variable symbol length of digital pulse interval modulation（DPIM）, it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation（FDPIM） method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.