动物骨源羟磷灰石负载Co3O4用于N2O催化分解

通过焙烧猪骨和鸡骨获得羟磷灰石(nHAP)载体,并采用浸渍法制备Co3O4/nHAP催化剂。采用XRD、N2物理吸附-脱附、FT-IR和H2-TPR等对催化剂进行表征,在连续流动微反装置上考察催化剂催化分解N2O的性能。结果表明,相比于鸡骨源Co3O4/nHAP催化剂,以猪骨源HAP为载体的催化剂因其较大的比表面积以及较小的Co3O4粒径尺寸,提供了更多的活性位点。特别是猪骨源Co3O4/nHAP催化剂中适量的K、Na等元素促进了Co^3+到Co^2+的还原,削弱了Co-O键,使催化剂的催化活性显著提高。     

Potassium-doped Co3O4 catalyst for direct decomposition of N2O

Direct decomposition of nitrous oxide (N₂O) on K-doped Co₃O₄ catalysts was examined. The K-doped Co₃O₄ catalyst showed a high activity even in the presence of water. In the durability test of the K-doped Co₃O₄ catalyst, the activity was maintained at least for 12 h. It was found that the activity of the K-doped Co₃O₄ catalyst strongly depended on the amount of K in the catalyst. In order to reveal the role of the K component on the catalytic activity, the catalyst was characterized by XRD, XPS, TPR and TPD. The results suggested that regeneration of the Co²⁺ species from the Co³⁺ species formed by oxidation of Co²⁺ with the oxygen atoms formed by N₂O decomposition was promoted by the addition of K to the Co₃O₄ catalyst.     

Promotion effect of residual K on the decomposition of N2O over cobalt–cerium mixed oxide catalyst

A series of cobalt–cerium mixed oxide catalysts (Co₃O₄–CeO₂) with a Ce/Co molar ratio of 0.05 were prepared by co-precipitation (with K₂CO₃ and KOH as the respective precipitant), impregnation, citrate, and direct evaporation methods and then tested for the catalytic decomposition of N₂O. XRD, BET, XPS, O₂-TPD and H₂-TPR methods were used to characterize the catalysts. Catalysts with a trace amount of residual K exhibited higher catalytic activities than those without. The presence of appropriate amount of K in Co₃O₄–CeO₂ may improve the redox property of Co₃O₄, which is important for the decomposition of N₂O. When the amount of K was constant, the surface area became the most important factor for the reaction. The co-precipitation-prepared catalyst with K₂CO₃ as precipitant exhibited the best catalytic performance because of the presence of ca. 2 mol% residual K and the high surface area. We also discussed the rate-determining step of the N₂O decomposition reaction over these Co₃O₄–CeO₂ catalysts.     

沉淀方式对沉淀法制备Co_3O_4催化N_2O直接分解性能的影响

以Co(NO_3)_2·6H_2O为钴源,K_2CO_3为沉淀剂,采用沉淀法制备Co_3O_4催化剂,用于催化N_2O直接分解反应。利用N_2~-物理吸附、XRD、FT-IR、TEM、TPR和ICP等对其进行表征,考察沉淀方式对Co_3O_4催化剂结构及其催化性能的影响。结果表明,沉淀方式对制备的Co_3O_4催化剂织构性质、物相组成和晶粒尺寸等影响不大,但显著影响其K残留量和还原性能,进而决定催化剂直接催化分解N_2O的催化性能。反加法制得的催化剂中K残留量为1.43%,明显高于正加法,同时催化剂中Co~(3+)较正加法更易还原,因而表现出更高的催化性能。在空速10 000 h~(-1)和N_2O体积分数0.1%的条件下,反加法制备的催化剂可在280℃催化N_2O完全分解,较正加法低20℃。     

Co3O4/CeO2 composite oxides for methane emissions abatement: Relationship between Co3O4–CeO2 interaction and catalytic activity

Co₃O₄/CeO₂ composite oxides with different cobalt loading (5, 15, 30, 50, 70 wt.% as Co₃O₄) were prepared by co-precipitation method and investigated for the oxidation of methane under stoichiometric conditions. Pure oxides, Co₃O₄ and CeO₂ were used as reference. Characterization studies by X-ray diffraction (XRD), BET, temperature programmed reduction/oxidation (TPR/TPO) and X-ray photoelectron spectroscopy (XPS) were carried out.

An improvement of the catalytic activity and thermal stability of the composite oxides was observed with respect to pure Co₃O₄ in correspondence of Co₃O₄–CeO₂ containing 30% by weight of Co₃O₄. The combined effect of cobalt oxide and ceria, at this composition, strongly influences the morphological and redox properties of the composite oxides, by dispersing the Co₃O₄ phase and promoting the efficiency of the Co³⁺–Co²⁺ redox couple. The presence in the sample Co₃O₄(30 wt.%)–CeO₂ of a high relative amount of Ce³⁺/(Ce⁴⁺ + Ce³⁺) as detected by XPS confirms the enhanced oxygen mobility.

The catalysts stability under reaction conditions was investigated by XRD and XPS analysis of the used samples, paying particular attention to the Co₃O₄ phase decomposition. Methane oxidation tests were performed over fresh (as prepared) and thermal aged samples (after ageing at 750 °C for 7 h, in furnace). The resistance to water vapour poisoning was evaluated for pure Co₃O₄ and Co₃O₄(30 wt.%)–CeO₂, performing the tests in the presence of 5 vol.% H₂O. A methane oxidation test upon hydrothermal ageing (flowing at 600 °C for 16 h a mixture 5 vol.% H₂O + 5 vol.%O₂ in He) of the Co₃O₄(30 wt.%)–CeO₂ sample was also performed. All the results confirm the superiority of this composite oxide.     

Ultrasound-assisted co-precipitation synthesis of mesoporous Co3O4–CeO2 composite oxides for highly selective catalytic oxidation of cyclohexane

The one-step highly selective oxidation of cyclohexane into cyclohexanone and cyclohexanol as the essential intermediates of nylon-6 and nylon-66 is considerably challenging. Therefore, an efficient and low-cost catalyst must be urgently developed to improve the efficiency of this process. In this study, a Co₃O₄–CeO₂ composite oxide catalyst was successfully prepared through ultrasound-assisted co-precipitation. This catalyst exhibited a higher selectivity to KA-oil, which was benefited from the synergistic effects between Co³⁺/Co²⁺ and Ce⁴⁺/Ce³⁺ redox pairs, than bulk CeO₂ and/or Co₃O₄. Under the optimum reaction conditions, 89.6% selectivity to KA-oil with a cyclohexane conversion of 5.8% was achieved over Co₃O₄–CeO₂. Its catalytic performance remained unchanged after five runs. Using the synergistic effects between the redox pairs of different transition metals, this study provides a feasible strategy to design high-performance catalysts for the selective oxidation of alkanes.     

Catalytic decomposition of N2O over supported Rh catalysts: effects of supports and Rh dispersion

The study of catalytic decomposition of nitrous oxide to nitrogen and oxygen over Rh catalysts supported on various supports (USY, NaY, Al₂O₃, ZrO₂, FSM-16, CeO₂, La₂O₃) showed that the activities of Rh/Al₂O₃ and Rh/USY (ultrastable Y zeolite) catalysts were comparable to or higher than the other catalysts reported in the literatures. The catalytic activity of N₂O decomposition was sensitive not only to the Rh dispersion but also to the preparation variables such as the Rh precursors and the supports used. A pulsed N₂O experiment over a Rh/USY catalyst suggested that the catalytic N₂O decomposition occurs on oxygen-covered surface and that O₂ may be freed on collision of N₂O molecules with the adsorbed oxygen atoms.     

Selective catalytic reduction of N2O in industrial emissions containing O2, H2O and SO2: behavior of Fe/ZSM-5 catalysts

The catalytic behavior in N₂O reduction by propane in the presence of O₂, H₂O and SO₂ of Fe/ZSM-5 catalysts prepared by ion exchange and chemical vapour deposition (CVD) is reported. The catalyst prepared by CVD shows a lower dependence of the rate of selective N₂O reduction on the decrease in C₃H₈ to N₂O ratio in the feed and a higher resistance to deactivation by SO₂ in accelerated durability tests with high SO₂ concentration (500 ppm). This catalyst shows stable catalytic behavior in the presence of SO₂ for more than 600 h of time-on-stream. Characterization of the catalysts by UV–VIS–NIR diffuse reflectance indicates that the poor performances of the sample prepared by ion exchange could be related to the presence of highly clustered Fe³⁺ species, in this catalyst. On the other hand, Fe₂O₃ particles are not present in the sample prepared by CVD while mainly isolated Fe³⁺ ions and iron-oxide nanoclusters are present.     

NO removal by CH4 on Co-NaX-CO and Ag-NaX catalysts in a dual-bed system

NO removal using CH₄ as a reductant in a dual-bed system has been investigated with Co-NaX and Ag-NaX catalysts, which were prepared by Co²⁺-, Ag⁺-ion exchange into zeolite NaX, respectively, and activation for 5 h at 500 °C. The experimental result has been compared with that of a Co-NaX-CO catalyst, additionally pre-treated under CO flow for the Co-NaX catalyst. The cobalt crystal structure of a Co-NaX-CO catalyst is Co₃O₄, which promotes NO oxidation to NO₂ by excess O₂ at a low temperature (523 K). The mechanical mixture of Co-NaX-CO and Ag-NaX catalysts shows a synergy effect on NO reduction to N₂ by CH₄ in the presence of excess O₂ and H₂O, but the NO reduction decreases quickly as time passes. However, the NO reduction to N₂ in a deNO bed at 523 K and a deNO₂ bed at 423 K, which are relatively lower than the reaction temperatures for common SCR systems, still remained at 67% even in a H₂O 10% gas mixture after 160 min.     

NO decomposition and reduction by CH4 over Sr/La2O3

Both NO decomposition and NO reduction by CH₄ over 4%Sr/La₂O₃ in the absence and presence of O₂ were examined between 773 and 973 K, and N₂O decomposition was also studied. The presence of CH₄ greatly increased the conversion of NO to N₂ and this activity was further enhanced by co-fed O₂. For example, at 773 K and 15 Torr NO the specific activities of NO decomposition, reduction by CH₄ in the absence of O₂, and reduction with 1% O₂ in the feed were 8.3·10⁻⁴, 4.6·10⁻³, and 1.3·10⁻² μmol N₂/s m², respectively. This oxygen-enhanced activity for NO reduction is attributed to the formation of methyl (and/or methylene) species on the oxide surface. NO decomposition on this catalyst occurred with an activation energy of 28 kcal/mol and the reaction order at 923 K with respect to NO was 1.1. The rate of N₂ formation by decomposition was inhibited by O₂ in the feed even though the reaction order in NO remained the same. The rate of NO reduction by CH₄ continuously increased with temperature to 973 K with no bend-over in either the absence or the presence of O₂ with equal activation energies of 26 kcal/mol. The addition of O₂ increased the reaction order in CH₄ at 923 K from 0.19 to 0.87, while it decreased the reaction order in NO from 0.73 to 0.55. The reaction order in O₂ was 0.26 up to 0.5% O₂ during which time the CH₄ concentration was not decreased significantly. N₂O decomposition occurs rapidly on this catalyst with a specific activity of 1.6·10⁻⁴ μmol N₂/s m² at 623 K and 1220 ppm N₂O and an activation energy of 24 kcal/mol. The addition of CH₄ inhibits this decomposition reaction. Finally, the use of either CO or H₂ as the reductant (no O₂) produced specific activities at 773 K that were almost 5 times greater than that with CH₄ and gave activation energies of 21–26 kcal/mol, thus demonstrating the potential of using CO/H₂ to reduce NO to N₂ over these REO catalysts.     

Cu-Mn氧化物催化N_2O直接分解性能

分别以Cu(NO_3)_2·3H_2O和50%Mn(NO_3)_2水溶液为铜源和锰源,K_2CO_3为沉淀剂,采用沉淀法和共沉淀法制备单一Cu、Mn氧化物催化剂和Cu-Mn-O复合氧化物催化剂,用于催化N_2O直接分解反应,并利用N_2物理吸附-脱附、XRD、FT-IR和TPR等进行表征。结果表明,单一Cu和Mn氧化物分别以体相CuO和Mn2O_3物相形式存在,Cu-Mn-O复合氧化物中除形成CuMn_2O_4尖晶石物相外,还有一定量小晶粒CuO,较单一氧化物具有更加优异的还原性能,表现出较高的催化N_2O直接分解活性。在空速10 000 h~(-1)和N_2O体积分数0.1%条件下,Cu-Mn-O复合氧化物催化剂可在440℃催化N_2O完全分解,分别较单一Cu和Mn氧化物催化剂降低了40℃和60℃。     

Catalytic decomposition of nitrous oxide N 2O: a study for p-block-element lead in PbO—ZrO2/Al2O3 systems

PbO—ZrO₂ catalysts have been prepared by sequential impregnation/calcination onto Al₂O₃ support for high concentration N₂O (27.97 mol%) decomposition. The p-block-element involved material system has been investigated with GC, BET, DTA, XRD and catalytic activity evaluation. It is found that with an atomic ratio Pb:Zr = 1:6 the material system shows the best catalytic performance for the decomposition. The catalyst with this composition has a tetragonal phase of ZrO₂ over reaction temperatures. The catalytic activity observed can be attributed to the presence of Pb cations with mixed valence states in tetragonal ZrO₂ lattice. Doping gases such as H₂O, CO₂, and O₂ are also mixed into the N₂O and studied. It is found that N₂O adsorption is rate-limiting step for the decomposition reaction. The reaction can be described as first order with respect to partial pressure of N₂O, considering that decomposition product O₂ exhibits no inhibition effect on the reaction in high conversion region.     

Co-ZSM-5 catalysts for N2O decomposition

The catalytic properties of cobalt containing ZSM-5 zeolites prepared by various methods were compared. TPR, XRD, N₂-BET, XPS, FTIR and UV–vis spectroscopy were used for characterizing the samples. Well-dispersed cobalt oxide-like species and isolated Co²⁺ ions in charge compensation positions were found in the zeolite. Catalysts prepared using a single step cation exchange method showed high activity for N₂O decomposition in a temperature range 300–550°C, in the presence of 0–5% O₂, and high stability in the presence of 10% H₂O to the feed. UV–vis spectra and TPR experiments indicated the presence of some cobalt oxides, not detected by DRX, in a Co-ZSM-5 catalyst containing 3.76 wt% Co, prepared by a solid-state reaction procedure. The N₂O conversion over this catalyst was strongly affected by addition of both O₂ and H₂O to the feed.     

The role of lanthana loading on the catalytic properties of Pd/Al2O3-La2O3 in the NO reduction with H2

The role of La₂O₃ loading in Pd/Al₂O₃-La₂O₃ prepared by sol–gel on the catalytic properties in the NO reduction with H₂ was studied. The catalysts were characterized by N₂ physisorption, temperature-programmed reduction, differential thermal analysis, temperature-programmed oxidation and temperature-programmed desorption of NO.

The physicochemical properties of Pd catalysts as well as the catalytic activity and selectivity are modified by La₂O₃ inclusion. The selectivity depends on the NO/H₂ molar ratio (GHSV = 72,000 h⁻¹) and the extent of interaction between Pd and La₂O₃. At NO/H₂ = 0.5, the catalysts show high N₂ selectivity (60–75%) at temperatures lower than 250 °C. For NO/H₂ = 1, the N₂ selectivity is almost 100% mainly for high temperatures, and even in the presence of 10% H₂O vapor. The high N₂ selectivity indicates a high capability of the catalysts to dissociate NO upon adsorption. This property is attributed to the creation of new adsorption sites through the formation of a surface PdO_x phase interacting with La₂O₃. The formation of this phase is favored by the spreading of PdO promoted by La₂O₃. DTA shows that the phase transformation takes place at temperatures of 280–350 °C, while TPO indicates that this phase transformation is related to the oxidation process of PdO: in the case of Pd/Al₂O₃ the O₂ uptake is consistent with the oxidation of PdO to PdO₂, and when La₂O₃ is present the O₂ uptake exceeds that amount (1.5 times). La₂O₃ in Pd catalysts promotes also the oxidation of Pd and dissociative adsorption of NO mainly at low temperatures (<250 °C) favoring the formation of N₂.     

单分散Co3O4@SiO2核壳催化剂的制备及N2O催化分解性能

N₂O是一种重要的温室气体,且对臭氧层有很大的破坏作用,而直接催化分解法是除去N₂O最经济有效的方法之一。针对目前报道较多的钴氧化物催化剂活性较差的问题,将包覆型Co₃O₄核壳材料引入N₂O直接催化分解反应,利用核壳结构的限域特性与壳层的多孔孔道使Co₃O₄分散性增加,粒径减小,金属载体相互作用与接触反应界面增强,从而提高了催化剂在N₂O直接催化分解反应中的低温活性。此外,还制备了一系列不同金属含量的Co₃O₄@SiO₂球形核壳催化剂来研究包覆结构对催化剂性能的影响,通过X射线荧光光谱（XRF）、透射电镜（TEM）、X射线衍射（XRD）、N₂物理吸附、H₂-程序升温还原（H₂-TPR）等表征,证实在保证稳定单分散核壳结构的前提下,活性Co₃O₄位点越多,催化剂反应活性越好。     

Catalytic performance of Co3O4/CeO2 and Co3O4/CeO2–ZrO2 composite oxides for methane combustion: Influence of catalyst pretreatment temperature and oxygen concentration in the reaction mixture

The influence of catalyst pre-treatment temperature (650 and 750 °C) and oxygen concentration (λ = 8 and 1) on the light-off temperature of methane combustion has been investigated over two composite oxides, Co₃O₄/CeO₂ and Co₃O₄/CeO₂–ZrO₂ containing 30 wt.% of Co₃O₄. The catalytic materials prepared by the co-precipitation method were calcined at 650 °C for 5 h (fresh samples); a portion of them was further treated at 750 °C for 7 h, in a furnace in static air (aged samples).

Tests of methane combustion were carried out on fresh and aged catalysts at two different WHSV values (12 000 and 60 000 mL g⁻¹ h⁻¹). The catalytic performance of Co₃O₄/CeO₂ and Co₃O₄/CeO₂–ZrO₂ were compared with those of two pure Co₃O₄ oxides, a sample obtained by the precipitation method and a commercial reference. Characterization studies by X-ray diffraction (XRD), BET and temperature-programmed reduction (TPR) show that the catalytic activity is related to the dispersion of crystalline phases, Co₃O₄/CeO₂ and Co₃O₄/CeO₂–ZrO₂ as well as to their reducibility. Particular attention was paid to the thermal stability of the Co₃O₄ phase in the temperature range of 750–800 °C, in both static (in a furnace) and dynamic conditions (continuous flow). The results indicate that the thermal stability of the phase Co₃O₄ heated up to 800 °C depends on the size of the cobalt oxide crystallites (fresh or aged samples) and on the oxygen content (excess λ = 8, stoichiometric λ = 1) in the reaction mixture. A stabilizing effect due to the presence of ceria or ceria–zirconia against Co₃O₄ decomposition into CoO was observed.

Moreover, the role of ceria and ceria–zirconia is to maintain a good combustion activity of the cobalt composite oxides by dispersing the active phase Co₃O₄ and by promoting the reduction at low temperature.     

Co3O4 based catalysts for NO oxidation and NOx reduction in fast SCR process

Reaction activities of several developed catalysts for NO oxidation and NO_x (NO + NO₂) reduction have been determined in a fixed bed differential reactor. Among all the catalysts tested, Co₃O₄ based catalysts are the most active ones for both NO oxidation and NO_x reduction reactions even at high space velocity (SV) and low temperature in the fast selective catalytic reduction (SCR) process. Over Co₃O₄ catalyst, the effects of calcination temperatures, SO₂ concentration, optimum SV for 50% conversion of NO to NO₂ were determined. Also, Co₃O₄ based catalysts (Co₃O₄-WO₃) exhibit significantly higher conversion than all the developed DeNO_x catalysts (supported/unsupported) having maximum conversion of NO_x even at lower temperature and higher SV since the mixed oxide Co-W nanocomposite is formed. In case of the fast SCR, N₂O formation over Co₃O₄-WO₃ catalyst is far less than that over the other catalysts but the standard SCR produces high concentration of N₂O over all the catalysts. The effect of SO₂ concentration on NO_x reduction is found to be almost negligible may be due to the presence of WO₃ that resists SO₂ oxidation.     

M_(0.5)Co_(2.5)O_4(M=La,Ce,Pr,Nd)尖晶石型复合氧化物催化剂催化分解N_2O性能

采用共沉淀法制备了M_(0.5)Co_(2.5)O_4(M=La,Ce,Pr,Nd)钴基尖晶石型复合氧化物催化剂,运用XRD、SEM、H_2-TPR和O_2-TPD-TG等对催化剂物化性能进行表征,并在固定床微型反应器中评价催化剂催化分解N_2O性能。结果表明,稀土金属掺杂改性的钴基尖晶石型复合氧化物催化剂粒径明显减小,比表面积增加,氧化还原性能得到改善,催化分解N_2O活性提高,其中,M_(0.5)Co_(2.5)O_4催化剂催化分解N2O温度低,T10和T95分别为342℃和499℃。     

Co-Cu-Ce-Fe/γ-Al_2O_3催化剂催化分解N_2O的性能

以等体积浸渍法制备γ-Al_2O_3负载的Co、Cu、Ce和Fe氧化物催化剂,利用正交试验设计实验条件,采用XRD、BET和H_2-TPR等对催化剂进行表征,并考察活性组分对催化剂催化分解N_2O活性的影响。结果表明,催化剂具有尖晶石结构,其BET比表面积随着金属氧化物负载量增加而降低。催化剂中铜的氧化物可以降低还原峰温度,进而明显提高催化活性,Co和Fe的加入对活性有一定的提高,Ce对催化活性没有明显影响。     

Steam reforming of ethanol over Co3O4/CeO2 catalysts prepared by different methods

In this paper, Co₃O₄/CeO₂ catalysts for steam reforming of ethanol (SRE) were prepared by co-precipitation and impregnation methods. The catalysts prepared by co-precipitation were very active and selective for SRE. Over 10%Co₃O₄/CeO₂ catalyst, ethanol conversion was close to 100% and hydrogen selectivity was about 70% at 450 °C. The catalysts were characterized by X-ray diffraction, temperature-programmed reduction (TPR) and BET surface area measurements. The preparation method influenced the interaction between cobalt and CeO₂ evidently. The incorporation of Co ions into CeO₂ crystal lattice resulted in weaker interaction between cobalt and ceria on catalyst surface. In comparison with catalysts prepared by impregnation, more cobalt ions entered into CeO₂ lattice, and resulted in weaker interaction between active phase and ceria on surface of Co₃O₄/CeO₂ prepared by co-precipitation. Thus, cobalt oxides was easier to be reduced to metal cobalt which was the key active component for SRE. Meanwhile, the incorporation of Co ions into CeO₂ crystal lattice was beneficial for resistance to carbon deposition.