Lignin‐based polycondensation resins for wood adhesives

Lignin‐based wood adhesives are obtained that satisfy the requirements of relevant international standards for the manufacture of exterior‐grade wood particleboard. Formulations based on low molecular mass lignin and presenting an increase in the relative proportion of reactive points yield better results than the higher molecular mass lignin used in the past. These lignins allow a higher proportion of hydroxymethylation during preparation of methylolated lignins. These lignin‐based adhesives also yield acceptable results at particleboard pressing times that are sufficiently low to be of industrial significance. Lignin‐based wood adhesives, in which a nonvolatile nontoxic aldehyde (glyoxal) is substituted for formaldehyde in their preparation, are prepared and tested for application to wood panels such as particleboard. The adhesives yield good internal bond strength results for the panels, which are good enough to comfortably pass relevant international standard specifications for exterior‐grade panels. The adhesives also show sufficient reactivity to yield panels in press times comparable to that of formaldehyde‐based commercial adhesives. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1690–1699, 2007     

Lignin–phenol–formaldehyde resin adhesives prepared with biorefinery technical lignins

In this study, four biorefinery technical lignins were used to synthesize lignin–phenol–formaldehyde (LPF) resin adhesives with a proposed formulation that was designed based on accurate analysis of the active sites in lignin with ³¹P nuclear magnetic resonance (NMR). The properties of the LPF resin adhesives and the plywoods prepared with them were tested. The structural features and curing behavior of the LPF resin adhesives were thoroughly investigated by solution‐ and solid‐state ¹³C NMR. Results indicated that the proposed formulation exhibited favorable adaptability for all four of these technical lignins for synthesis of LPF resin adhesives. High‐performance plywood with low emissions of formaldehyde could be successfully prepared with the synthesized LPF resin adhesives. All the LPF resin adhesives exhibited similar structure and curing behavior with the commercial phenol–formaldehyde (CPF) resin adhesive. However, the LPF resin adhesives showed relatively higher curing temperatures as compared with the CPF resin adhesive. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42493.     

Evaluation of block shear properties of selected extreme‐pH structural adhesives by short‐term exposure test

Nine structural adhesives with varying pH were selected to examine the effect of adhesive pH on wood–adhesive bond quality. The adhesives evaluated included four highly alkaline phenol–formaldehyde, one intermediate pH phenol–resorcinol–formaldehyde, two acidic melamine–urea–formaldehyde, and two acidic melamine–formaldehyde resins. Block shear specimens were prepared using Douglas‐fir and black spruce wood. The adhesive performance was evaluated by measuring the shear properties (strength and wood failure) of the specimens tested at the dry and vacuum–pressure–redry (VPD) conditions. Adhesive pH, test condition, and wood species showed significant effects on shear properties. The different adhesives performed differently at the dry and VPD conditions. The high‐pH adhesives (phenol–formaldehyde and phenol–resorcinol–formaldehyde) showed similar high wood failures at both test conditions and performed better than the low‐pH adhesives (melamine–formaldehyde and melamine–urea–formaldehyde), especially after the VPD conditioning. The low‐pH adhesives showed high wood failure at the dry condition, but wood failure decreased significantly after VPD conditioning for both species, indicating that the low‐pH adhesives were less durable than the high‐pH adhesives. High‐pH adhesives did not have a negative impact on the strength of the bonded specimens. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Development and characterization of a wood adhesive using bagasse lignin

Bagasse is spent fiber left after extraction of sugar. It is mainly used as a fuel to concentrate sugarcane juice. In the present work, the possibility of preparing wood adhesives from bagasse has been explored. The parameters for the preparation of a lignin phenol formaldehyde (LPF) adhesive, (lignin concentration, formaldehyde to phenol molar ratio, catalyst concentration, reaction time and reaction temperature) have been optimized. It was found that up to 50% of phenol can be substituted by bagasse lignin to give LPF wood adhesive having better bonding strength in comparison to a control phenol formaldehyde (CPF) wood adhesive. Prepared resins were characterized using IR, DSC and TGA. IR spectra of LPF resin showed structural similarity with CPF resin. Thermal stability of LPF resin was found to be lower as compared to CPF resin. DSC studies reveal a lower curing temperature for LPF adhesive in comparison to CPF adhesive. A shelf-life study reveals that LPF exhibits consistent behavior as compared to CPF in respect to adhesive strength.     

Eucalyptus bark lignin substituted phenol formaldehyde adhesives: A study on optimization of reaction parameters and characterization

The major adhesive resin worldwide used in the manufacture of plywood is phenol formaldehyde resole (PF) resin. The raw material for this kind of adhesive is derived from petroleum oil. Because of rising prices of crude oil and the scarcity of petroleum products, their replacement by natural resource–based raw material has become a necessity. In the present work, the possibility of replacing phenol in PF resin with lignin was explored. The parameters for preparation of bark lignin substituted PF (LPF) adhesive, such as lignin concentration, formaldehyde to phenol molar ratio, catalyst concentration, reaction time, and reaction temperature, were optimized. It was found that up to 50 wt % of phenol can be substituted by lignin to give an LPF adhesive with better bonding strength compared to that of control PF resin. Prepared resins were characterized using IR, DSC, and TGA. IR spectra of LPF adhesive showed structural similarity with that of PF adhesives. Thermal stability of LPF adhesive was found to be lower compared to that of control PF (CPF) adhesive. DSC studies revealed a lower curing temperature for LPF resin than that for CPF resin. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3514–3523, 2004     

Synthesis and cure kinetics of liquefied wood/phenol/formaldehyde resins

Wood liquefaction was conducted at a 2/1 phenol/wood ratio in two different reactors: (1) an atmospheric three‐necked flask reactor and (2) a sealed Parr reactor. The liquefied wood mixture (liquefied wood, unreacted phenol, and wood residue) was further condensed with formaldehyde under acidic conditions to synthesize two novolac‐type liquefied wood/phenol/formaldehyde (LWPF) resins: LWPF1 (the atmospheric reactor) and LWPF2 (the sealed reactor). The LWPF1 resin had a higher solid content and higher molecular weight than the LWPF2 resin. The cure kinetic mechanisms of the LWPF resins were investigated with dynamic and isothermal differential scanning calorimetry (DSC). The isothermal DSC data indicated that the cure reactions of both resins followed an autocatalytic mechanism. The activation energies of the liquefied wood resins were close to that of a reported lignin–phenol–formaldehyde resin but were higher than that of a typical phenol formaldehyde resin. The two liquefied wood resins followed similar cure kinetics; however, the LWPF1 resin had a higher activation energy for rate constant k₁ and a lower activation energy for rate constant k₂ than LWPF2. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Properties of plywood panels bonded with ionic liquid-modified lignin–phenol–formaldehyde resin

The aim of this research was to investigate the physical and mechanical properties of plywood panels bonded with ionic liquid-modified lignin–phenol–formaldehyde (LPF) resin. For this purpose, soda bagasse lignin was modified by 1-ethyl-3-methylimidazolium acetate ([Emim][OAc]) ionic liquid, and then, various contents of modified lignins (10, 15, and 20 wt%) were added as a substitute of phenol in phenol–formaldehyde (PF) resin synthesis. The properties of the synthesized resin were compared with those of a control PF resin. The changes in curing behavior of the resins prepared were analyzed by differential scanning calorimetry (DSC). The physical properties of the resins prepared, as well as the water absorption, thickness swelling, shear strength, and formaldehyde emission of the plywood panels bonded with these adhesives, were measured according to standard methods. DSC analysis indicated that in comparison with PF resins, curing of the LPF resin occurred at lower temperatures. The physical properties of the synthesized resins indicated that viscosity and solid content increased, while gel time and density decreased by addition of treated lignin to the PF resin. Although the panels containing resins with modified lignin yielded low formaldehyde emission, their dimensional stability was worse than those bonded with a commercial PF adhesive. The plywood prepared using IL-treated lignin PF resins has shear strength, which satisfy the requirements of the relevant standards specifications and significantly better than that of panels prepared with the control PF resin. The mechanical properties of the panels could be significantly enhanced with increased percentage of treated lignin content from 0 to 20 wt%.     

Phenol Formaldehyde Resin Modification with Lignin

Abstract

Lignin (poly‐phenylpropane units) was precipitated from waste black liquor produced by paper manufacture from rice straw. The use of this lignin as partial substitution of phenol in phenol formaldehyde resin is investigated. The effect of different variables [e.g., lignin concentration, ratio of formaldehyde to phenol lignin (phenol + lignin), temperature, and polymerization time on the properties of the produced resin is studied]. The effect of the chemical modification of lignin by oxidation, reduction, and hydrolysis on the properties of the produced phenol lignin formaldehyde resin is also studied. Hydrolysis of lignin by hydrochloric acid increases the reactivity between lignin, formaldehyde, and phenol in producing resin with good properties more than untreated lignin. Also, the percent of replaced phenol with lignin in the resin can be increased by hydrolysis of lignin with hydrochloric acid. So, the reactivity of lignin toward resin formation has the following sequence: hydrolyzed lignin > oxidized lignin with dichromate > treated lignin with sodium hydrosulfite.     

Development and characterization of a lignin–phenol–formaldehyde wood adhesive using coffee bean shell

In the present study, the possibility of development of a wood adhesive using coffee bean shell lignin (Cbsl) has been explored. Cbsl-modified phenolic adhesive has been prepared by replacing phenol with lignin at different weight percents. The optimization of weight percent lignin incorporation was carried out with respect to mechanical properties. It was found that up to 50 wt% of phenol could be replaced by Cbsl to give lignin–phenol–formaldehyde adhesive (LPF) with improved bond strength in comparison to control phenol–formaldehyde (CPF). Optimized LPF and CPF adhesives were characterized by IR, DSC and TGA. The IR spectrum of LPF showed structural similarity to CPF. Thermal stability of LPF adhesive was found to be lower as compared to that of CPF. DSC studies revealed a higher rate of curing in the LPF adhesive.     

Influence of acrylamide copolymerization of urea–formaldehyde resin adhesives to their chemical structure and performance

To lower the formaldehyde emission of wood‐based composite panels bonded with urea–formaldehyde (UF) resin adhesive, this study investigated the influence of acrylamide copolymerization of UF resin adhesives to their chemical structure and performance such as formaldehyde emission, adhesion strength, and mechanical properties of plywood. The acrylamide‐copolymerized UF resin adhesives dramatically reduced the formaldehyde emission of plywood. The ¹³C‐NMR spectra indicated that the acrylamide has been copolymerized by reacting with either methylene glycol remained or methylol group of UF resin, which subsequently contributed in lowering the formaldehyde emission. In addition, an optimum level for the acrylamide for the copolymerization of UF resin adhesives was determined as 1%, when the formaldehyde emission and adhesion strength of plywood were taken into consideration. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Impact of curing condition on pH and alkalinity/acidity of structural wood adhesives

Nine formulations were selected for evaluating the effect of different curing methods on pH and alkalinity or acidity of various structural wood adhesives. These included four phenol–formaldehyde (PF) resins with high pH, one phenol–resorcinol–formaldehyde (PRF) resin with intermediate pH, two melamine–urea–formaldehyde (MUF) resins, and two melamine–formaldehyde (MF) resins with low pH. The four curing methods used in the study were: (1) curing at 102–105°C for 1 h (based on CSA O112.6‐1977), (2) four‐hour curing at 66°C followed by 1‐hour curing at 150°C (based on ASTM D1583‐01), (3) curing at room temperature overnight (based on ASTM D 1583‐01), and (4) cured adhesive squeezed out from glue lines of bonded shear block samples. The effect of the different methods on pH and alkalinity/acidity of the cured adhesive depended strongly on the individual adhesives. For the PF, the alkalinity was different for the different formulations in the liquid form, while in the cured form, the difference in the alkalinity depended on the curing method used. The MF and the MUF were the adhesives most affected by the method used. In particular, the MUF showed much higher cured film pH values when cured by method 2 compared to the other three methods, while both the cured MF and MUF exhibited quite variable acidity values when cured with the different methods. The PRF showed reasonably uniform cured film pH but varying acidity values when cured with the different methods. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Use of a methylolated softwood ammonium lignosulfonate as partial substitute of phenol in resol resins manufacture

The synthesis of lignin‐phenol‐formaldehyde (LPF) was studied to determine its optimum operating conditions. The lignin proposed as phenol substitute has been the softwood ammonium lignosulfonate. The resin synthesis was optimized by varying the methylolated lignosulfonate content, 18–52%; the sodium hydroxide to phenol‐modified lignosulfonate molar ratio, 0.3–0.94; and the formaldehyde to phenol‐modified lignosulfonate molar ratio, 1.1–3.5. The parameters employed in the characterization of LPF resins were free phenol, free formaldehyde, gel time, alkaline number, viscosity, pH, solid content, and chemical structure changes. The properties of LPF resin comply with the requirements for its utilization in plywood manufacture. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 643–650, 2004     

Waste liquors from cellulosic industries. IV. Lignin as a component in phenol formaldehyde resol resin

The lignin separated from the spent liquor of soda pulping of rice straw can replace a part of phenol in the condensation reaction with formaldehyde in a basic medium to form phenol lignin–formaldehyde (PL–F) resol resin. The production of phenol lignin–formaldehyde resol resin was carried out in two stages: First was the formation of the adduct (lignin phenol) using different lignin percentages; second was the condensation of the adduct with formaldehyde. Reaction variables, i.e., molar ratio of formaldehyde to phenol lignin, polymerization time, amount of sodium hydroxide as a catalyst, and polymerization temperature in the polymerization step were studied. Solubility of the produced resol resin in different solvents, its viscosity, and yield were determined. Lignin could replace up to 40% of phenol in the produced resin. Infrared spectra of the prepared resin were determined. Structural similarity of phenol–formaldehyde to phenol lignin–formaldehyde resin was shown. Also, relative absorbance of characteristic bands of the resins were calculated and claimed too much on the effect of reaction parameters on the prepared resins.     

Wood–phenol adhesives prepared from carboxymethylated wood. I

Preparation of carboxymethylated wood (CM wood)–phenol resin adhesives has been attempted by two methods, “kneading method” and “solvolysis method,” and their adhesion strength has been studied. The two preparation methods differ in the dissolution step. In the case of the kneading method, CM wood was dissolved in aqueous phenol by kneading at 100–120°C under shear, whereas, in the case of the solvolysis method, the dissolution was facilitated by phenolysis at 80°C in the presence of appropriate amounts of hydrochloric acid. The wood-based adhesive prepared by the solvolysis method revealed excellent and enhanced applicability compared with that of the adhesive prepared by the kneading method, although the latter can be used as an adhesive for wood. Adhesion strength of these adhesives was enhanced when poorly substituted CM wood and appropriate amounts of formaldehyde were used in the resin preparation. A crosslinking agent for carboxymethyl cellulose, that is, polymeric MDI, was also added just before application. The water-proof adhesion strength was higher than the JIS specification for phenol resin adhesives for this modification.     

Preparation and performance of lignin–phenol–formaldehyde adhesives

Steam explosion lignin phenol formaldehyde (SEL–PF) adhesives were prepared by ternary gradual copolymerization. The parameters for the phenolate of steam explosion lignin (SEL) and preparation of SEL–PF adhesives were optimized. Under the optimum phenolate conditions, the phenolic hydroxyl content of lignin increased by 130%, whilst the methoxyl content was reduced by 68%. The SEL–PF adhesives were used to prepare plywoods by hot-pressing. The pH value, viscosity, solid content, free phenol content and free formaldehyde content of SEL–PF adhesives were investigated. The bonding strengths of the plywoods glued with SEL–PF adhesives were determined. The maximum SEL replacement percentage of phenol reached 70 wt%, and the properties of adhesives and plywoods met the Chinese National Standard (GB/T 14732-2006) for first grade plywood.     

Microwave‐assisted hydrothermal liquefaction of lignin for the preparation of phenolic formaldehyde adhesive

This study aimed to produce phenolic formaldehyde (PF) adhesives using the liquefaction product of bagasse lignin (LPBL) as a partial substitute for petroleum‐based phenol. Lignin was extracted from bagasse using 93% acetic acid solution and was rapidly degraded in hot‐compressed water by microwave heating using oxalic acid as catalyst. The liquefaction yield reached 78.69% under the optimal reaction condition. Gas chromatography–mass spectrometry (GC/MS) analysis showed that the main chemical compounds of the liquefaction product included mono‐substituted and bis‐substituted phenols, such as 2,6‐dimethoxyphenol, 4‐hydroxybenzaldehyde, and so on. The LPBL was employed to replace a portion of phenol at varying ratios from 0 to 20 wt % in the preparation of PF adhesives. The molecular weight, viscosity, and adhesive strength of LPBL‐PF adhesives were found to be lower than those of pure PF adhesives. With the phenol replaced by LPBL up to 20%, the viscosity and adhesive strength of the resin were 4.046 Pa s and 1.017 MPa, respectively. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44510.     

Fast advancement and hardening acceleration of low‐condensation alkaline PF resins by esters and copolymerized urea

Low‐condensation phenol‐formaldehyde (PF) resins coreacted under alkaline conditions with up to 42% molar urea on phenol during resin preparation yielded PUF resins capable of faster hardening times than equivalent pure PF resins prepared under identical conditions and presented better performance than the latter. The water resistance of the PUF resins prepared seemed comparable to pure PF resins when used as adhesives for wood particleboard. Part of the urea was found by ¹³C‐NMR to be copolymerized to yield the alkaline PUF resin; whereas, especially at the higher levels of urea addition, unreacted urea was still present in the resin. Increase of the initial formaldehyde to phenol molar ratio decreased considerably the proportion of unreacted urea and increased the proportion of PUF resin. A coreaction scheme of phenolic and aminoplastic methylol groups with reactive phenol and urea sites based on previous model compounds work has been proposed, copolymerized urea functioning as a prebranching molecule in the forming, hardened resin network. The PUF resins prepared were capable of further noticeable curing acceleration by addition of ester accelerators; namely, glycerol triacetate (triacetin), to reach gel times as fast as those characteristic of catalyzed aminoplastic resins, but at wet strength values characteristic of exterior PF resins. Synergy between the relative amounts of copolymerized urea and ester accelerator was very noticeable at the lower levels of the two parameters, but this effect decreased in intensity toward the higher percentages of urea and triacetin. ¹³C‐NMR assignements of the relevant peaks of the PUF resins are reported and compared with what has been reported in the literature for mixed, coreacted model compounds and pure PF and urea‐formaldehyde (UF) resins. The relative performance of the different PUF resins prepared was checked under different conditions by thermomechanical analysis (TMA) and by preparation of wood particleboard, and the capability of the accelerated PUF resins to achieve press times as fast as those of aminoplastic (UF and others) resins was confirmed. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 359–378, 1999     

木材工业用胶粘剂的现状及发展趋势

主要介绍了脲醛树脂、酚醛树脂、三聚氰胺－ 甲醛树脂、木质素、单宁、异氰酸酯等木材工业用胶粘剂的研制状况及发展趋势。     

Solution‐state NMR analysis of hydroxymethylated resorcinol cured in the presence of crude milled‐wood lignin from Acer saccharum

Resorcinol‐formaldehyde adhesives can reinforce stress fractures that appear from wood surface preparation. Researchers have found that applying the resorcinol‐formaldehyde prepolymer, hydroxymethylated resorcinol, to the surface of wood improves the bond strength of epoxy and polyurethane adhesives to wood. Hydroxymethylated resorcinol is thought to plasticize lignin components and stabilize stress fractures through reactions with lignin subunits and hemicelluloses in wood. In this study, a dilute solution of hydroxymethylated resorcinol (HMR) is cured in the presence of a crude milled‐wood lignin (cMWL) from Acer saccharum and subsequently dissolved in dimethylsulfoxide‐d₆ to delineate reactivity with lignin and O‐acetyl‐(4‐O‐methylglucurono)xylan using solution‐state NMR spectroscopy. ¹H–¹³C single‐bond correlation NMR experiments revealed that the HMR only formed 4,4′‐diarylmethane structures with itself in the presence of the cMWL; the 2‐methylols that formed remained free and did not crosslink with resorcinol. Cured HMR resin formed both 4,4′‐ and 2,4‐diarylmethane structures, confirming that the presence of lignin and O‐acetyl‐(4‐O‐methylglucurono)xylan hinders crosslinking at the C‐2 position. No evidence of reactivity between HMR and lignin subunits was found. New peaks consistent with ester linkages were observed in ¹³C‐NMR spectra of the cMWL sample treated with HMR that may be attributable to HMR moieties condensing with glucuronic acid substituents. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45398.     

木质素在人造板胶黏剂中的应用

综述了木质素在酚醛树脂、脲醛树脂、三聚氰胺甲醛树脂3种人造板胶黏剂中的应用进展，指出了利用无毒、稳定、价廉、可再生的木质素代替不可再生且有毒的苯酚、甲醛制取工业用人造板胶黏剂是木材用胶黏剂领域的重要研究方向。