Migration analysis,antioxidant, and mechanical characterization of polypropylene-based active food packaging films loaded with BHA,BHT, and TBHQ

Polypropylene (PP) based active composite films were prepared by adding butylated hydroxy anisole (BHA), butylated hydroxytoluene (BHT), and tertiary butylated hydroquinone (TBHQ) antioxidants using the extrusion molding process. All concentrations of BHT, 2% to 3% BHA, and 3% TBHQ significantly increased the tensile strength (TS) of the composite films compared with control films. Increasing antioxidant concentration decreased TS values for BHT films, whereas an opposite trend was observed for BHA and TBHQ films. BHA at < 2%, BHT at > 2%, and TBHQ at all added concentrations significantly reduced elongation at break (E_b) of the composite films compared to control films. Water vapor permeability (WVP) of 1% BHT film was not significantly different from control. However, other antioxidants especially at increased concentrations significantly increased WVP values. TBHQ films with 300% to 662% increase had the highest WVP and BHT films with 5% to 81% increase had the lowest WVP among composite films. All three antioxidants had a negative effect on the transparency of the films; however the effect of BHA at higher concentrations was greater. The antioxidants did not change the color attributes of the films. Films containing all antioxidants showed 2,2-diphenyl-1-picrylhydrazyl radical-scavenging activity, which increased with increase in their concentration, especially for those containing 3 wt.% BHT and TBHQ. Overall, incorporating BHA and BHT into a PP matrix improved mechanical, barrier, antioxidant properties, and film appearance and consequently were proposed for the development of antioxidant active PP films. TBHQ film is not recommended for food packaging because of its weak mechanical properties (lower E_b and TS values, higher WVP, and greater migration).     

Determination of Four Synthetic Phenolic Antioxidants in Edible Oils by High-Performance Liquid Chromatography with Cloud Point Extraction Using Tergitol TMN-6

A cloud-point extraction (CPE) method using Tergitol TMN-6 (TMN-6) non-ionic surfactant was developed for the extraction and preconcentration of propyl gallate (PG), tertiary butyl hydroquinone (TBHQ), butylated hydroxyanisole (BHA), and butylated hydroxytoluene (BHT) in edible oils. The optimum conditions of CPE were 1.5 % (v/v) Tergitol TMN-6, 1 % (w/v) NaCl, ultrasound-assist 15 min at 49 KHz, 20 min equilibrated at 45 °C, and centrifugation for 10 min at 3,000 rpm. The surfactant-rich phase was then analyzed by reversed-phase high-performance liquid chromatography (HPLC) with ultraviolet detection at 280 nm, under gradient separation, using methanol and 1.5 % (v/v) acetic acid. Under the study conditions, four synthetic phenolic antioxidants (SPAs) were successfully separated within 24 min. Limits of detection in the studied edible oils were in the range of 1.6 to 9.0 ng mL^?1. The high recoveries of the spiked edible oils were obtained in the range 90–98 %. The CPE method has been shown to be a potentially useful methodology for the preconcentration of the target analytes, with a preconcentration factor of 25. This method was compared with cloud point extraction (using Triton X-114) and liquid–liquid extraction (using methanol).     

气相色谱--质谱法测定XO酱中BHA、BHT和TBHQ

采用气相色谱—质谱(全扫描方式)测定XO酱中丁基羟基茴香醚(BHA)、二丁基羟基甲苯(BHT)和叔丁基对苯二酚(TBHQ)。样品用甲醇振荡萃取，以DB—5MS为分析柱。3种组分的回收率在85％～99％之间，相对标准偏差小于8．4％；样品中BHA、BHT和TBHQ的检测限分别为0．05、0．05和0．10(mg／kg)。该法简单、快速、准确，可用于XO酱等基质复杂的富油食品中BHA、BHT和TBHQ的检测和确证。     

Quantification of aristolochic acids I and II in herbal dietary supplements by ultra-high-performance liquid chromatography–multistage fragmentation mass spectrometry

A rapid, selective and sensitive ultra-high-performance liquid chromatography–multistage fragmentation mass spectrometry (UHPLC-MS³) method was developed and evaluated for the determination of aristolochic acids I and II (AA I and II) in herbal dietary supplements. A hybrid triple quadrupole/linear ion-trap mass spectrometry was used to monitor MS³ ion transitions m/z 359.2 > 298.1 > 268.0 and m/z 329.2 > 268.2 > 238.0 to detect AA I and II, respectively. The extraction and clean-up of target analytes from dry powdered samples was performed using the quick, easy, cheap, effective, rugged and safe (QuEChERS) procedure. Herbal liquid extracts were analysed directly. Average recoveries ranged from 89% to 112%, with relative standard deviations (RSDs) ranging from 3% to 16%. Limits of quantification (LOQs) estimated for three selected matrices were as follows (AA I/II): 5/10 ng g^?1 (tablets); 25/50 ng g^?1 (capsules); and 2.5/5.0 ng ml^?l (liquid herbal extract). The method was applied in a limited survey of 30 herbal products marketed in the United States via the Internet. AA I and II were detected in 20% and 7%, respectively, of tested samples.     

Simultaneous determination of five quinoxaline-1,4-dioxides in animal feeds using an immunochromatographic strip

An immunochromatographic (ICG) strip was developed for the simultaneous quantitative determination of five quinoxaline-1,4-dioxides in animal feed. For this purpose, polyclonal antibodies (PcAb) with group-specific quinoxaline-1,4-dioxides were conjugated to colloidal gold particles as the detection reagent for ICG strips to test for quinoxaline-1,4-dioxides. This method achieved semi-quantitative detection of quinoxaline-1,4-dioxides within 5–10 min. The visual lower detection limits of the strip for quinocetone, cyadox, carbadox, mequindox and olaquindox were 10, 15, 15, 20 and 20 ng ml^?1, respectively. Using an ICG strip reader, the 50% inhibitions (IC₅₀ values) were calculated to be 9.1, 13.5, 16.6, 20.2 and 21.3 ng ml^?1 for quinocetone, cyadox, carbadox, mequindox and olaquindox, respectively. When used to analyse samples of animal feed, acceptable recovery rates of 77.5–99.5% and coefficients of variation (CVs) of 4.3–10.7% were obtained. Levels measured with the ICG strip for 10 spiked samples were confirmed by HPLC with a high correlation coefficient of 0.9965 (n = 10). In conclusion, the method was rapid and accurate for simultaneous determination of five quinoxaline-1,4-dioxides antibiotics in animal feed.     

Terbium-sensitised luminescence screening method for fluoroquinolones in beef serum

Enrofloxacin and danofloxacin are the only fluoroquinolone antibiotics approved for use in cattle in the United States. Microbial screening methods commonly used for monitoring veterinary drug residues are not sensitive or selective for fluoroquinolones. In this work, a luminescence-based screening assay was developed to detect fluoroquinolones in beef serum. This approach takes advantage of the DNA-enhanced luminescence signal of a fluoroquinolone–Tb⁺³ complex. In this method, serum samples were extracted with acidified acetonitrile in the presence of magnesium sulfate. After centrifugation, evaporation of the supernatant was followed by dissolution of the residue in buffer and filtration. Addition of Tb⁺³ and DNA then allowed a reading of the luminescence signal. The technique was illustrated using enrofloxacin, and provided good recoveries (73–88%) at 25, 50 and 100 ng ml^?1, with reasonable RSDs averaging at 11%. The LOD was 2.5 ng ml^?1 based on the variability of response of control serum samples from 18 different steers. The method provided no false-positive or false-negative results while screening blind samples for enrofloxacin and was demonstrated to be quantitative over a range of 0–100 ng ml^?1.     

Synthesis,characterisation and analytical application of Fe3O4@SiO2@polyaminoquinoline magnetic nanocomposite for the extraction and pre-concentration of Cd(II) and Pb(II) in food samples

This work describes a novel Fe₃O₄@SiO₂@polyaminoquinoline magnetic nanocomposite and its application in the pre-concentration of Cd(II) and Pb(II) ions. The parameters affecting the pre-concentration procedure were optimised by a Box–Behnken design through response surface methodology. Three variables (extraction time, magnetic sorbent amount and pH) were selected as the main factors affecting the sorption step, while four variables (type, volume and concentration of the eluent, and elution time) were selected as main factors in the optimisation study of the elution step. Following the sorption and elution of analytes, the ions were quantified by flame atomic absorption spectrometry (FASS). The limits of detection were 0.1 and 0.7 ng ml^?1 for Cd(II) and Pb(II) ions, respectively. All the relative standard deviations were less than 7.6%. The sorption capacities of this new sorbent were 57 mg g^?1 for Cd(II) and 73 mg g^?1 for Pb(II). Ultimately, this nanocomposite was successfully applied to the rapid extraction of trace quantities of these heavy metal ions from seafood and agricultural samples and satisfactory results were obtained.     

Determination of caramel colorants’ by-products in liquid foods by ultra-high-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS)

2-Methylimidazole, 4-methylimidazole (2-MI and 4-MI), 2-acetyl-4-(1,2,3,4-tetrahydroxybutyl) imidazole (THI) and 5-hydroxymethylfurfural (5-HMF) are neo-formed compounds generated during the manufacture of caramel colours and are transferred to the processed food. These contaminants are known to have a toxicological profile that may pose health risks. Hence, to characterise THI, 2- and 4-MI and 5-HMF levels in liquid foods, an ultra-high-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) method was developed and sample preparation was divided into two analytical strategies depending on the concentration range expected in the type of foods targeted. For the determination of the imidazole substitutes (THI, 2- and 4-MI), a sample enrichment and clean-up step by strong cation solid-phase extraction was developed. This method is capable of quantifying over a range of 5 ng ml^–1 (LOQ) to 500 ng ml^–1 with recoveries of 75.4–112.4% and RSDs of 1.5–15%. For determination of 5-HMF, a standard addition method was applied covering the linear range of 0.25–30 µg ml^–1 with RSDs from 2.8% (for intraday precision) to 9.2% (for intermediate precision). The validated analytical methods were applied to 28 liquid food samples purchased from local markets. THI was found only in the beer samples at levels up to 141.2 ng ml^–1. For 2-MI, non-quantifiable traces were observed for all samples, while 4-MI was observed in all samples with large concentration variations (from < LOQ to 563.9 ng ml^–1). 5-HMF was found at expected concentrations, except for a sherry vinegar sample (113 µg ml^–1), which required a high level of dilution before following the standard addition protocol.     

Vortex-Assisted Liquid–Liquid Microextraction Combined with HPLC for the Simultaneous Determination of Five Phthalate Esters in Liquor Samples

A vortex-assisted liquid–liquid microextraction (VALLME) method using hexanoic acid as extractant followed by high-performance liquid chromatography–diode array detection was developed for the extraction and determination of five phthalate esters (PAEs) including bis-methylglycol ester (DMEP), benzyl butyl phthalate (BBP), dicyclohexyl phthalate (DCHP), di-n-butyl phthalate (DBP), and di-n-octyl phthalate (DNOP) from liquor samples. In this method, hexanoic acid was employed as extraction solvent, because its density is lower than water. And vortex mixing was utilized as a mild emulsification procedure to reduce emulsification time and improve the effect of extraction. Under the studied conditions, five phthalate esters were successfully separated within 20 min and the limits of detection were 2.3 ng mL^?1 for DMEP, 1.1 ng mL^?1 for BBP, 1.9 ng mL^?1 for DCHP, 1.2 ng mL^?1 for DBP, and 1.5 ng mL^?1 for DNOP, respectively. Recoveries of the PAEs spiked into liquor samples were ranged from 89 to 93 %. The precisions of the proposed method were varied from 1.6 to 2.6 % (RSD). The VALLME method has been proved to have the potential to be applied to the preconcentration of the target analytes. Moreover, the method is simple, high sensitivity, consumes much less solvent than traditional methods and environmental friendly.     

PSE-HPLC 法测定食品中叔丁基羟基茴香醚和2,6- 二叔丁基羟基甲苯

目的：建立测定食品中抗氧化剂叔丁基羟基茴香醚(BHA)和2,6- 二叔丁基羟基甲苯(BHT)加压溶剂萃取-高效液相色谱法(PSE-HPLC 法)。方法：采用正交试验对影响PSE 萃取效率的温度、压力、萃取溶剂、萃取时间进行优化,联合HPLC 进行测定,并确定分别以BHA 提取量、BHT 提取量以及总量为评价指标的最优条件。结果：PSE-HPLC 法测定BHT 和BHA 的相对标准偏差(RSD)为0.5%～3.1%,并且在1.0～200.0μg/mL 范围内色谱峰面积与组分质量浓度均有很好的线性相关性(r ≥ 0.9997),检出限为0.05μg/mL,在最优条件下的回收率为92.60%～97.80%。结论：PSE-HPLC 法简便、快速、效率高,方法的重现性、线性相关性以及检出限理想,适用于食品中BHT 和BHA 含量及两者总量的同时快速检测。     

Escherichia coli O157: H7 Growth in Laboratory Media as Affected by Phenolic Antioxidants

Five strains of Escherichia coli O157:H7 with ATCC 11775 E. coli were grown in brain heart infusion (BHI) broth (pH 5.8, adjusted with citric acid) and treated with butylated hydroxyanisole (BHA), butylated hy-droxytoluene (BHT), tertiary butylhydroquinone (TBHQ), and propyl gallate (PG) individually or combined. Additives ranged from 100–400 ppm with inocula levels between 5 and 104 CFU/mL in tissue culture plates or in flasks; samples were incubated at 4°C or 37°C for 24 hr. Additive antimicrobial efficacy varied with inoculum level and incubation temperature. BHA at <200 ppm was bactericidal on all strains. Poly-hydroxyl additives (TBHQ, PG) were less effective at 4°C. BHA-BHT combinations were synergistic at 4°C.     

Headspace solid-phase microextraction coupled to gas chromatography-tandem mass spectrometry for the determination of haloanisoles in sparkling (cava and cider) and non-sparkling (wine) alcoholic beverages

A highly sensitive analytical method was developed to determine 2,4,6-trichloroanisole (TCA), 2,3,4,6-tetrachloroanisole (TeCA), 2,4,6-tribromoanisole (TBA) and 2,3,4,5,6-pentachloroanisole (PCA) in sparkling alcoholic beverages. The method was based on the use of headspace solid-phase microextraction (HS-SPME) using a polydimethylsiloxane (PDMS) fibre. It was coupled to gas chromatography-triple quadrupole tandem mass spectrometry (GC-QqQ-MS/MS) for the detection and quantification of the target haloanisoles. The method was fully automated and no sample preparation was needed. The method was validated for alcoholic beverages. The influence of CO₂ on the extraction efficiency was also evaluated for the studied sparkling drinks (cava and cider). All the calibration curves showed good linearity (R² > 0.98) within the tested range (1–50 ng l^?1). Recoveries were evaluated at three different levels (1, 5 and 50 ng l^?1) and were always between 71% and 119%. Precision was expressed as relative standard deviation (RSD), and was evaluated as intra- and inter-day precisions, with values ≤ 22% in both cases. Limits of quantitation (LOQs) were ≤ 0.91 ng l^?1, which are below the sensory threshold levels for such compounds in humans. The validated method was applied to commercial samples, 10 cavas and 10 ciders, but it was also used for the analysis of nine red wines and four white wines, demonstrating the further applicability of the proposed method to non-sparkling beverages. TCA was detected in most samples at up to 0.45 ng l^?1.     

Kinetics of Growth and Inhibition of Listeria monocytogenes in the Presence of Antioxidant Food Additives

Listeria monocytogenes strain Scott A in Tryptose Broth was treated with 100-300 ppm butylated hydroxyanisole (BHA), 300-700 ppm butylated hydroxytoluene (BHT) and 10-30 ppm tertiary butylhydroquinone (TBHQ). Resulting growth curves were fitted using the logistic model, and growth parameters [lag period (LP), generation time (GT), and maximum growth (MG)] were calculated. BHA and BHT inhibited Listeria monocytogenes by increasing LP and GT and decreasing MG. Extent of inhibition was concentration-dependent for cultures with BHA, but not with BHT. TBHQ at 10-30 ppm increased LP but did not affect other parameters. LP increased exponentially with increased BHA or TBHQ in Listeria culture. Concentrations of additive required to increase LP by one order of magnitude were 240 ppm for BHA and 26 ppm for TBHQ.     

Aspergillus and aflatoxin in groundnut (Arachis hypogaea L.) and groundnut cake in Eastern Ethiopia

This study was conducted to assess major Aspergillus species and aflatoxins associated with groundnut seeds and cake in Eastern Ethiopia and evaluate growers’ management practices. A total of 160 groundnut seed samples from farmers’ stores and 50 groundnut cake samples from cafe and restaurants were collected. Fungal isolation was done from groundnut seed samples. Aspergillus flavus was the dominant species followed by Aspergillus parasiticus. Aflatoxin analyses of groundnut seed samples were performed using ultra performance liquid chromatography; 22.5% and 41.3% of samples were positive, with total aflatoxin concentrations of 786 and 3135 ng g^?1 from 2013/2014 and 2014/2015 samples, respectively. The level of specific aflatoxin concentration varied between 0.1 and 2526 ng g^?1 for B₂ and B₁, respectively. Among contaminated samples of groundnut cake, 68% exhibited aflatoxin concentration below 20 ng g^?1, while as high as 158 ng g^?1 aflatoxin B₁ was recorded. The study confirms high contamination of groundnut products in East Ethiopia.     

Development of a novel controlled-release nanocomposite based on poly(lactic acid) to increase the oxidative stability of soybean oil

A poly(lactic acid) (PLA)-based nanocomposite active packaging was developed for the controlled release of tert-butylhydroquinone (TBHQ) antioxidant. The PLA-based active films were loaded with only TBHQ (3% wt) or a mixture of modified cellulose nanofibre (MCNF) (8% wt) and TBHQ (3% wt) to obtain active and nanocomposite active films, respectively. Release studies indicated that the release rate of TBHQ in 95% ethanol simulant was significantly decreased by the addition of MCNF. Moreover, the presence of MCNF diminished the increasing effect of temperature on the release rate as when storage temperature increased from 4°C to 40°C. The diffusion coefficient (D) for PLA-TBHQ and PLA-MCNF-TBHQ films increased from 6.75 and 4.34 × 10^?8 cm² s^?1 to 19.85 and 8.49 × 10^?8 cm² s^?1, respectively. Diffusion of TBHQ to soybean oil was enough to delay the induction of the oxidation of soybean oil stored for 6 months in contact with PLA-based films. Antioxidative activity of PLA-based active films considerably increased with increasing storage time as indicated by the increase in 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging activity and the oxidative stability index (p < 0.05). This study demonstrates that effective controlled release antioxidant packaging could be obtained by using MCNF nanofiller, which leads to prolonged activity and an extended shelf-life in fatty foods.     

Simultaneous Determination of TBH<Subscript>2</Subscript>Q and BHA Antioxidants in Food Samples Using Eosin Y Film Modified Electrode

A glassy carbon electrode (GCE) was modified with eosin Y that was electrodeposited on GCE via continuous cycling between ??1.6 and 1.5 V (vs Ag/AgCl). This electrode was characterized by scanning electron microscopy and electrochemical impedance spectra. The resulting electrode exhibited excellent electrocatalytic activity toward the oxidation of butylated hydroxyanisole (BHA) and tert-butyl hydroquinone (TBH₂Q); in addition, the oxidation products of BHA and TBH₂Q were found to be the same, which was studied by CV and in situ FT-IR spectroelectrochemistry. Under the optimized condition, the oxidation peak currents were linear to BHA/TBH₂Q in the range from 0.10 to 7.00 μg mL^?1 with the detection limits of 0.01 μg mL^?1 (S/N?=?3) for BHA and 0.015 μg mL^?1 (S/N?=?3) for TBH₂Q, respectively. Moreover, the reproducibility and repeatability of the electrode were determined. The proposed method was successfully applied in the simultaneous determination of BHA and TBH₂Q in several edible oil samples, and satisfactory results when compared with those obtained using high-performance liquid chromatography.     

Quantification of malachite green in fish feed utilising liquid chromatography-tandem mass spectrometry with a monolithic column

The purpose of this study was to develop a rapid and sensitive method for the quantification of malachite green (MG) in fish feed using LC-ESI-MS/MS with a monolithic column as stationary phase. Fish feed was cleaned using ultrasonic assisted liquid–liquid extraction. The separation was achieved on a Chromolith^® Performance RP-18e column (100 × 4.6 mm) using gradient mobile phase composition of methanol and 0.1% formic acid at the flow rate of 1.0 ml min^–1. The analyte was ionised using electrospray ionisation in positive mode. Mass spectral transitions were recorded in selected reaction monitoring (SRM) mode at m/z 329.78 → m/z 314.75 with a collision energy (CE) of 52% for MG. The system suitability responses were calculated for reproducibility tests of the retention time, number of theoretical plates and capacity factor. System validation was evaluated for precision, specificity and linearity of MG. The linearity and calibration graph was plotted in the range of 15.0–250 ng ml^?1 with the regression coefficient of >0.997. The lower limits of detection and quantification for MG were 0.55 and 1.44 ng ml^?1, respectively, allowing easy determination in fish feed with accuracy evaluated as a percentage recovery of 92.1% and precision determined as % CV of < 5. The method was also extended to the determination of MG in an actual fish feed. The sensitivity and selectivity of LC-ESI-MS/MS using monolithic column offers a valuable alternative to the methodologies currently employed for the quantification of MG in fish feeds.     

Simultaneous detection of sulfamethazine and sulfaquinoxaline using a dual-label time-resolved fluorescence immunoassay

A dual-label time-resolved fluoroimmunoassay (TRFIA) was introduced for the simultaneous quantification of sulfamethazine (SM₂) and sulfaquinoxaline (SQX). Lanthanide (Eu³⁺ and Sm³⁺)-labelled antibodies were used because lanthanides have higher stabilities and narrower emission spectra than most fluorescent dyes. The sensitivity of the TRFIA for SM₂ was 0.02 ng ml^?1, and the average recoveries and the intra- and inter-assay CVs were 77.2–107.6%, 5.4–10.5%, and 6.0–11.2%, respectively. The sensitivity of the TRFIA for SQX was 0.04 ng ml^?1; and the average recoveries and the intra- and inter-assay CVs were 74.1–102.8%, 4.6–10.9%, and 8.7–11.2%, respectively. The method was used to analyse chicken tissue and egg samples, and the results agreed well with the results of HPLC and enzyme-linked immunosorbent assay (ELISA) analyses, with correlation coefficients (R²) of 0.9415–0.9724. The TRFIA developed is a simple, fast and sensitive method for the high-throughput simultaneous screening of SM₂ and SQX in edible animal tissues.     

Fusarium species identification and fumonisin production in maize kernels from Shandong Province,China, from 2012 to 2014

A total of 225 maize kernel samples were collected from Shandong Province in China from 2012 to 2014 and analysed for contamination with Fusarium spp. and fumonisins (FBs) using molecular methods and high-performance liquid chromatography with fluorescence detection. The results showed that the average incidences of Fusarium spp. in 2012, 2013 and 2014 were 23.3%, 37.1% and 36.5%, respectively, Fusarium verticillioides being the predominant species. In 2012, the average contamination level of FBs was 3071 ng g^?1, which was higher than that in 2014 (2913 ng g^?1) and 2013 (2072 ng g^?1). Of all samples, 13% and 19% had FB contamination levels higher than 2000 and 4000 ng g^?1, which are the maximum limits as set by the Food and Drug Administration of the United States and the European Commission, respectively. Therefore, efforts should be taken to minimise the potential risk of FBs to the health of humans and animals.     

Antimicrobial effects of butylated hydroxyanisole alone or in combination with potassium sorbate on quality changes in palm oil co-inoculated with Aspergillus flavus and Bacillus spp

Palm oil was sterilised and subjected to different concentrations (0.2 to 1.0 g litre⁻¹) of butylated hydroxyanisole (BHA) alone or in combination with potassium sorbate (KS) and co- inoculated with Aspergillus flavus and Bacillus species, the most prevalent organisms isolated from the palm oil. A dramatic increase of c3.43, 3.16 or 1.83 log₁₀ cfu ml⁻¹ microbial populations occurred in control samples or those treated with 0.2 or 1.0 g litre⁻¹ of BHA alone respectively. On the contrary, populations lower by approximately 1.0–1.3 log₁₀ cfu ml⁻¹ occurred in samples subjected to the combination treatment. Bi-phasic minima-extended-lag-phases were observed in the samples treated with BHA + KS. Mycelial growth was markedly inhibited in samples preserved with BHA + KS, being more apparent at concentrations of between 0.4 and 0.8 g litre⁻¹ of BHA in combination with potassium sorbate. Similarly, significantly (P = 0.05) lower free fatty acid content was observed in samples subjected to the combination treatment particularly at concentrations ranging from 0.6 litre⁻¹. Changes in pH were minimal suggesting less microbial activity, but significantly lower values occurred in samples treated with BHA alone after 14 days of ambient (30(±3) °C) storage. Better sensory qualities (less ‘separation’ i.e enhanced stability and aroma) were exhibited by samples preserved with the combination of BHA with KS. These various induced changes demonstrate the importance of concentration, residence time and synergism in relation to the effectiveness of antimicrobial agents. The benefits of the application of combination treatments have been shown and could be exploited by palm oil processors and importers. However, samples treated with the low concentrations are more likely to present potential hazards to consumers. © 1999 Society of Chemical Industry