焊接电流对不锈钢焊条熔滴过渡及熔滴中夹杂物的影响

采用水中收集熔滴、光学显微分析、电子扫描能谱分析、计算机图象分析及平板堆焊等试验方法,研究了焊接电流对E308-16不锈钢焊条熔滴中夹杂物的影响.结果表明,焊接电流增大时,焊条的熔滴质量比和熔滴的平均质量减小 ,熔滴的过渡频率增高,熔滴中非金属夹杂物含量增大,焊缝中的气孔率与熔滴中夹杂物含量之间不存在严格的规律性对应关系;熔滴中非金属夹杂物是熔滴区化学反应的产物,属" 内生"性质.     

焊接电流对不锈钢焊条熔滴过度及熔滴中夹杂物的影响

采用水中收集熔滴、光学显微分析、电子扫描能谱分析、计算机图象分析及平板堆焊等试验方法,研究了焊接电流对Ｅ３０８－１６不锈钢焊条熔滴中夹杂物的影响,结果表明,焊接电流增大时,焊条的熔滴质量比和熔滴的平均质量减小,熔滴的过渡频率增高,熔滴中非金属夹杂物含量增大,焊缝中的气孔率与熔滴中夹杂物含量之间不存在严格的规律性对应关系;熔滴中非金属夹杂物是熔滴区化学反应的产物,属“内生”性质。     

活性剂对CO2气体保护焊焊缝成形及飞溅的影响

使用自制的活性焊丝,研究了活性剂对CO2气体保护焊焊缝成形及飞溅的影响。结果表明,使用活性剂可以使焊接飞溅率大大降低,焊缝熔深增加,熔宽增大,焊缝表面成形光滑。认为CO2气体保护焊飞溅降低的原因,是因为活性剂的加入在降低了混合气体的有效电离电压的同时显著增加了CO2电弧的导电能力,使电弧能量密度增加,从而使中等电流下的熔滴过渡方式由大颗粒过渡转变成细颗粒过渡。     

CO2气体保护焊短路过渡控制技术的研究现状与展望

CO2气体保护焊因成本低、生产率高等特点,广泛应用于制造业。随着制造业节能减排的需求日益增加及汽车轻量化概念的推广,制造业对薄板焊接的要求不断提高,传统的焊接方式已不能满足其要求。CO2短路过渡焊相对于传统的焊接方式(钨极氩弧焊、熔化极氩弧焊、激光焊等),具有高热稳定性、低热输入、低熔深等特点,但其焊接飞溅大、焊缝成形差,从而限制了其广泛应用。CO2短路过渡焊接过程是由燃弧阶段与短路阶段组成的复杂的非线性时变系统,熔滴过渡过程决定了焊接过程的稳定性与焊缝成形的优劣。燃弧阶段熔滴在电磁收缩力、表面张力、等离子流力、金属蒸发反作用力等多种力的共同作用下长大并与熔池接触短路,同时形成稳定液桥。短路阶段,液桥在表面张力、电磁收缩力和粘滞力的作用下形成缩颈并断开。燃弧阶段的熔滴尺寸、振荡特性,短路阶段熔池的振荡特性、峰值电流都对熔滴过渡稳定性有十分重要的影响。针对短路过渡焊飞溅产生机制的研究表明,熔滴、熔池的氧化还原反应、短路前期产生的瞬时短路和短路末期液桥电爆炸是导致焊接过程不稳定及产生飞溅的主要因素。国内外众多焊接研究者针对CO2短路过渡焊熔滴过渡过程及控制技术进行了大量的研究与探索,研究工作主要分为四个方向:焊接材料成分的优化,基于焊接电源输出电信号的熔滴过渡建模及控制,基于视觉传感技术的熔滴过渡控制和基于磁控技术的CO2短路过渡焊接技术。活性焊丝和药性焊丝的推广可有效降低焊接飞溅;波控技术及衍生的CMT技术在使用小电流参数焊接时取得了优异的焊接效果;中、小电流参数条件下,磁控焊接技术可有效解决焊接飞溅和成形差问题。本文从焊丝、电源、外加磁场形式和工艺四个方面综述了国内外CO2气体保护焊短路过渡控制技术的研究现状,首先分析了CO2短路过渡焊焊接飞溅的产生机理,其次介绍了典型的CO2气体保护焊短路过渡控制技术的原理、特点和局限性,分析了不同短路过渡控制技术的特点,最后阐述了目前短路过渡控制技术在研究和应用过程中存在的问题及解决办法,并对该领域下一步发展趋势进行了展望。     

减少短路过渡CO_2焊接飞溅新途径

利用诱导冲脉电流诱导熔滴过渡是减少CO_2短路过渡焊接飞溅的新方法。这个方法不仅明显地减少了金属飞溅,而且也使熔滴过渡规律化,增强了焊接过程的稳定性,改善了焊缝成形。本文详细地讨论和分析了这种熔滴过渡的特点及其减少飞溅的原因。     

脉冲参数对高强奥氏体焊丝MIG焊接熔滴过渡的影响

采用高速摄像技术和汉诺威弧焊分析仪研究了脉冲频率、基值电流、脉宽比以及脉冲波形对H08Cr18Ni27Mo6奥氏体焊丝MIG焊接熔滴过渡的影响,结果表明,脉冲频率、基值电流与脉宽比对熔滴过渡影响较大,而脉冲波形影响较小,采用较高脉冲频率、较小的脉宽比并结合适当的基值电流能够获得理想的熔滴过渡形式。     

粗丝CO_2气体保护焊熔滴过渡与潜弧机理的研究

本文详细分析了粗丝CO_2气体保护潜弧焊熔滴过渡的特点和潜弧机理。潜弧状态可以分为三种类型:半潜弧(熔滴主要以较大的颗粒形式过渡)、临界潜弧(熔滴主要以较小颗粒的射滴形式过渡)和深潜弧(熔滴以细小射滴与射流混和形式过渡)。大电流、低电压、粗焊丝、反极性和氧化性气氛是形成潜弧过程的必要条件,其中电流是最重要的条件。潜弧后弧柱气氛改变,焊丝端部的弧根由集中形态扩展为覆盖整个端部形态,使得熔滴尺寸变得细小,熔滴过渡形式发生变化。采用临界潜弧区域的焊接规范参数施焊,飞溅小,工艺过程稳定,焊缝成形优良。     

焊剂片约束电弧焊接三明治板熔滴过渡与熔池波动研究

针对焊剂片约束电弧(FBCA)焊接高强钢三明治板熔池研究难点,采用侧边贴敷耐高温石英玻璃片方法,采集焊接动态过程信息,实现熔池边缘曲线的提取与特征参数的计算,研究不同参数下熔滴过渡模式及熔池边缘曲线波动情况,分析熔池振荡角与焊接稳定性及焊缝成形之间的关系。结果表明：不同参数下FBCA焊接存在短路过渡、粗滴过渡、排斥过渡、细滴过渡、射滴过渡、弧桥并存过渡六种过渡方式,对芯板内熔池边缘波动的影响依次减弱;随着熔池振荡角变化,熔池边缘曲线形状存在混合U形、深U形及浅U形,电弧燃烧稳定性依次增强;当焊接处于弧桥并存过渡模式、熔池边缘曲线为浅U形时,电弧稳定燃烧,电弧力作用均匀,焊接过程稳定,焊缝质量最好。     

CMT能量输入特点与熔滴过渡行为

为分析CMT焊接方法的工艺特点,采用高速CCD摄像机建立了电弧形态和熔滴过渡视觉传感系统并且通过电流、电压传感器建立了波形采集系统,以此分析其能量输入特点和熔滴过渡行为.结果显示,CMT焊接波形控制呈现典型的直流脉冲特征,焊接时热输入较低;在CMT短路过渡过程中,熔滴尺寸随焊接电流的增加幅度不大,将熔滴尺寸控制在一定范围内可实现稳定的短路过渡.CMT短路过渡通过焊丝回抽,避免了大的电磁力,有效地消除了飞溅.当电流增大到一定值时,其过渡形式将转变为射滴过渡和短路过渡的混合过渡.     

不同脉冲、频率下的双丝匹配对焊缝的影响研究

目的 为提高双丝焊接质量,探究不同脉冲和频率下的双丝匹配对焊接质量的影响。方法 采用MIG焊接技术,在3 mm厚的不锈钢板上进行焊接实验,之后观察和分析焊缝表面形貌、电流波形、金相组织以及截面几何形状参数。结果 在同一频率下,前丝单脉冲组的熔深总是小于对应双脉冲组。随着双脉冲频率的增大,熔深、余高也随之增大,熔宽变化不大。结论 在频率为4 Hz时进行焊接能得到较为美观的焊缝。在双丝匹配时,前丝单脉冲会阻碍后丝双脉冲对基板的挖掘和熔滴对熔池的搅拌作用,且前后丝位置顺序对熔深、余高影响较大,对内部金相组织生长形态影响较小。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.