DMFCs用磺化聚醚醚酮/磺化酚酞型聚醚砜共混质子交换膜

A sulfonated poly(ether ether ketone) (SPEEK) membrane with fairly high degree of sulfonation (DS) swells excessively and even dissolves at high temperature. To solve these problems, sulfonated phenolphthalein poly(ether sulfone) (SPES-C, DS 53.7%) is blended with the SPEEK matrix (DS 55.1%, 61.7%) to prepare SPEEK/SPES-C blend membrane. The decrease in swelling degree and methanol permeability of the membrane is dose-dependent. Pure SPEEK (DS 61.7%) membrane dissolves completely in water at 70ºC, whereas the swelling degree of the SPEEK (DS 61.7%)/SPES-C (40%, by mass) membrane is 29.7% at 80ºC. From room temperature to 80ºC, the methanol permeability of all SPEEK (DS 55.1%)/SPES-C blend membranes is about one order of magnitude lower than that of Nafion®115. At higher temperature, the addition of SPES-C polymer increases the dimensional stability and greater proton conductivity can be achieved. The SPEEK (DS 55.1%)/SPES-C (40%, by mass) membrane can withstand temperatures up to 150ºC. The proton conductivity of SPEEK (DS 55.1%)/SPES-C (30%, by mass) membrane approaches 0.16 S•cm－1, matching that of Nafion115 at 140ºC and 100% RH, while pure SPEEK (DS 55.1%) membrane dissolves at 90ºC. The SPEEK/SPES-C blend membranes are promising for use in direct methanol fuel cells because of their good dimensional stability, high proton conductivity, and low methanol permeability.     

Sulfonated polyether sulfone‐poly(vinylidene fluoride) blend membrane for DMFC applications

Direct methanol fuel cell (DMFC) proton exchange membranes were prepared by blending poly (vinylidene fluoride) (PVDF) with sulfonated poly(ether sulfone) (SPES). Using a diffusion cell and gas chromatographic technique, the effects of PVDF content on methanol permeability in the blended membranes were investigated. The thermal resistance and proton conductivity of the membranes were also determined by using a thermal gravimetric analysis (TGA) and an impedance analysis technique respectively. The presence of sulfonic acid groups in SPES was confirmed by Fourier transform infrared (FTIR). It was found that the methanol permeability in the blended membranes decreased with PVDF content at the expense of proton conductivity. Blended membranes show methanol permeability values much lower than that of Nafion 115, whereas the proton conductivities of the membranes are comparable with that of Nafion. The thermal stability of these blended membranes is above 250°C, which is sufficiently high for use in DMFC. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Modified Sulfonated Poly(ether ether ketone) Based Mixed Matrix Membranes for Direct Methanol Fuel Cells

Mixed matrix membranes based on zeolite 4A‐methane sulfonic acid (MSA)‐sulfonated poly(ether ether ketone) (SPEEK) are evaluated as a potential polymer electrolyte membrane (PEM) for direct methanol fuel cells (DMFCs). Ion‐exchange capacity, sorption of water, and water–methanol mixture, proton conductivity, and methanol permeability for the mixed‐matrix membranes have been extensively investigated. The mixed‐matrix membranes are also characterized for their cross‐sectional morphology, mechanical, and thermal properties. DMFCs employing SPEEK‐MSA (20 wt.%) blend, zeolite 4A (4 wt.%)‐SPEEK‐MSA (20 wt.%) mixed matrix membranes deliver peak power densities of 130 and 159 mW cm^–2, respectively; while a peak power density of only 95 mW cm^–2 is obtained for the DMFC employing pristine SPEEK membrane at 70 °C. The results showed that these SPEEK based mixed matrix membranes exhibit higher DMFC performance and lower methanol permeability in comparison to Nafion‐117 membrane.     

Sulfonated poly(ether ether sulfone) copolymers for proton exchange membrane fuel cells

Novel aromatic sulfonated poly(ether ether sulfone)s (SPEESs) with tert‐butyl groups were synthesized by aromatic nucleophilic polycondensation of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenylsulfone (SDCDPS), 4,4′‐dichlorodiphenylsulfone (DCDPS), and tert‐butylhydroquinone (TBHQ). The resulting copolymers showed very good thermal stability and could be cast into tough membranes. The morphology of the membranes was investigated with atomic force microscopy. The proton conductivity of SPEES‐40 membranes increased from 0.062 S/cm at 25°C to 0.083 S/cm at 80°C, which was higher than the 0.077 S/cm of Nafion 117 under the same testing conditions. These copolymers are good candidates to be new polymeric electrolyte materials for proton exchange membrane fuel cells. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1443–1450, 2007     

Proton exchange membranes based on poly(vinylidene fluoride) and sulfonated poly(ether ether ketone)

Blend membranes were obtained by solution casting from poly(vinylidene fluoride) (PVDF) and sulfonated poly(ether ether ketone) (SPEEK) in N,N-dimethylacetamide (DMAc). DSC and XRD were used to characterize the structure of the blend membranes. The effect of PVDF content on the membrane properties was investigated. The methanol permeability, water uptake and the swelling ratio of blend membranes decreased with the increase of PVDF content. Though the proton conductivity decreased upon the addition of PVDF, they were still comparable to that of Nafion^® 117 membrane. Higher selectivities were also found for most blend membranes in comparison with Nafion^® 117 membrane. The effect of methanol concentration on solution uptake, swelling ratio and methanol permeability of the blend membranes was also studied.     

Methanol permeability and properties of DMFC membranes based on sulfonated PEEK/PVDF blends

Proton exchange membranes for a direct methanol fuel cell were prepared by blending poly(vinylidene fluoride) [PVDF] with sulfonated poly(etheretherketone) [SPEEK]. The effects of PVDF content on methanol permeability in the blend membranes were investigated by using a diffusion cell and gas chromatography technique. The thermal resistance and proton conductivity of the membranes were also determined by using a thermal gravimetric analysis (TGA) and an impedance analysis technique, respectively. It was found that methanol permeability in the blend membranes decreased with PVDF content at the expense of proton conductivity. The methanol permeability values of the blend membranes are much lower than that of Nafion 115, whereas proton conductivities of the membranes are comparable to that of Nafion. The thermal stability of these blend membranes are above 250°C which is sufficiently high for use in DMFC. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5941–5947, 2006     

Crosslinked monosulfonated poly(arylene ether) using cyclodimerization of trifluorovinyl ether groups for fuel cell applications

A crosslinker and crosslinkable sulfonated poly(arylene ether)s with trifluorovinyl ether groups were synthesized via reaction of 4‐trifluorovinyloxyphenol for application in fuel cells. Crosslinked poly(arylene ether) membranes were prepared by thermal irradiation, and the cyclodimerization of the trifluorovinyl ether groups in the polymers as well as the crosslinker was confirmed using differential scanning calorimetry and infrared measurements. These crosslinked membranes showed a low swelling ratio, comparable to that of Nafion 112. The proton conductivity of the crosslinked membranes was 0.17 and 0.3 S cm^?1 at 30 and 80 °C, respectively, much higher than that of Nafion 112 under the same conditions. The excellent dimensional stability and high conductivity of the crosslinked membranes can be attributed to this new type of crosslinking system (end‐group crosslinking) as well as the chemical structure of crosslinked (multi‐block) polymers. Copyright © 2011 Society of Chemical Industry     

Preparation and characterizations of direct methanol fuel cell membrane from sulfonated polystyrene/poly(vinylidene fluoride) blend compatibilized with poly(styrene)‐b‐poly(methyl methacrytlate) block copolymer

This work concerned a development of sulfonated polystyrene (SPS)/poly(vinylidene fluoride) (PVDF) blend membrane for use as an electrolyte in a direct methanol fuel cell. The aim of this work was to investigate effects of the blend ratio on properties of the blend membranes. The partially SPS with various degrees of substitution were prepared by using propionyl sulfate as a sulfonating agent. After that, the optimum SPS was selected for further blending with PVDF, at various blend ratios. Poly(styrene)–poly(methyl methacrytlate) block copolymer (PS‐b‐PMMA), used as a compatibilizer, was synthesized via a controlled radical polymerization through the use of an iniferter. Thermal behaviors, water uptake, proton conductivity, and methanol permeability of various blend membranes were determine by using TGA, gravimetry, impedance analyzer, and gas chromatography, respectively. From the results, it was found that, water uptake and methanol permeability of the blend membranes tended to increase with the weight ratio of SPS. It was also found that the blend membranes were incompatible, especially those containing more than 40 wt % of the SPS. However, by adding 5 wt % of the block copolymer, the blend became more compatible. Mechanical strength, proton conductivity, and resistance to methanol crossover of the blend membrane remarkably increased after the compatibilization. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Solution‐blown SPEEK/POSS nanofiber–nafion hybrid composite membranes for direct methanol fuel cells

This study aims to develop novel hybrid composite membranes (NHMs) by impregnating Nafion solution into the porous sulfonated poly(ether ether ketone)/polyhedral oligomeric silsesquioxanes (SPEEK/POSS) nanofibers (NFs). The composite membrane was prepared by solution blowing of a mixture of SPEEK/POSS solution. The characteristics of the SPEEK/POSS NFs and the NHMs, including morphology, thermal stability, and performance of membrane as PEMs, were investigated. The performance of NHMs was compared with that of Nafion117 and SPEEK/Nafion composite membranes. Results showed that the introduction of POSS improved the proton conductivity, water swelling, and methanol permeability of membranes. A maximum proton conductivity of 0.163 S cm^?1 was obtained when the POSS content was 6 wt % at 80°C, which was higher than that of Nafion117 and SPEEK/Nafion. NHMs could be used as proton exchange membranes (PEMs) for fuel cell applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42843.     

Partially Sulfonated Poly(vinylidene fluoride) Induced Enhancements of Properties and DMFC Performance of Nafion Electrolyte Membrane

Partially sulfonated poly(vinylidene fluoride) (SPVdF) has been prepared by incorporation of sulfonic acid groups within poly(vinylidene fluoride), using chlorosulfonic acid as the sulfonating agent. The degree of sulfonation (DS) has been varied by modulating the duration of the sulfonation reaction. Blending of SPVdF (having DS = 36.78%) with Nafion at a constituent wt.% ratio of SPVdF:Nafion = 70:30 has resulted in the fabrication of polymer electrolyte membrane with superior properties compared to pristine Nafion‐117 membrane. This particular blend composition exhibited a proton conductivity value of 3.6 × 10⁻² S cm⁻¹ (i.e. ∼12.5% increase over Nafion‐117), a methanol permeability value of 6.81 × 10⁻⁷ cm² s⁻¹ at 6M methanol concentration (i.e. ∼99.31% decrease from Nafion‐117) and a corresponding membrane selectivity value of 5.29 × 10⁴ Ss cm⁻³ (i.e. an increase of approximately two‐orders of magnitude over Nafion‐117) at 20 °C. In addition, this blend composition has also exhibited (a) better heat stability at temperatures as high as 160 °C by virtue of it possessing higher glass transition temperature, (b) higher storage modulus, (c) higher stress relaxation at high angular frequency and (d) superior DMFC performance at high methanol feed concentration in presence of humidified, as well as, non‐humidified air as the catholyte, compared to Nafion‐117 membrane.     

Sulfonated poly(ether ether ketone)/zirconium tricarboxybutylphosphonate composite proton-exchange membranes for direct methanol fuel cells

Sulfonated poly(ether ether ketone) (SPEEK) is a very promising alternative membrane material for direct methanol fuel cells. However, with a fairly high degree of sulfonation (DS), SPEEK membranes can swell excessively and even dissolve at high temperature. This restricts membranes from working above a high tolerable temperature to get high proton conductivity. To deal with this contradictory situation, insolvable zirconium tricarboxybutylphosphonate (Zr(PBTC)) powder was employed to make a composite with SPEEK polymer in an attempt to improve temperature tolerance of the membranes. SPEEK/Zr(PBTC) composite membranes were obtained by casting a homogeneous mixture of Zr(PBTC) and SPEEK in N,N-dimethylacetamide on a glass plate and then evaporating the solvent at 60°C. Many characteristics were investigated, including thermal stability, liquid uptake, methanol permeability and proton conductivity. Results showed significant improvement not only in temperature tolerance, but also in methanol resistance of the SPEEK/Zr(PBTC) composite membranes. The membranes containing 30 wt-% ∼ 40 wt-% of Zr(PBTC) had their methanol permeability around 10⁻⁷ cm²·s⁻¹ at room temperature to 80°C, which was one order of magnitude lower than that of Nafion?115. High proton conductivity of the composite membranes, however, could also be achieved from higher temperature applied. At 100% relative humidity, above 90°C the conductivity of the composite membrane containing 40 wt-% of Zr(PBTC) exceeded that of the Nafion?115 membrane and even reached a high value of 0.36 S·cm⁻¹ at 160°C. Improved applicable temperature and high conductivity of the compositemembrane indicated its promising application inDMFC operations at high temperature. __________ Translated from Acta Polymerica Sinica, 2007, (4): 337–342 [译自:高分子学报]     

Sulfonated poly(ether ether ketone)/epoxy/phenol novolac blend proton‐exchange membranes with low methanol permeability

A crosslinked epoxy [4,4′‐diglycidyl‐(3,3′,5,5′‐tetramethylbiphenyl) epoxy resin (TMBP)], cured by phenol novolac (PN), was introduced into a sulfonated poly(ether ether ketone) (SPEEK) membrane (ion‐exchange capacity = 2.0 mequiv/g) with a casting‐solution, evaporation, and heating crosslinking method to improve the mechanical properties, dimensional stability, water retention, and methanol resistance. By Fourier transform infrared analysis, the interactions between the sulfonic acid groups and hydroxyl groups in the blend membranes were confirmed. The microstructure and morphology of the blend membranes were investigated with atomic force microscopy. As expected, the blend membranes showed excellent mechanical properties, good thermal properties (thermal stability above 200°C), lower swelling ratios (1.4% at 25°C and 7.0% at 80°C), higher water retention (water diffusion coefficient = 9.8 × 10^?6 cm²/s), and a lower methanol permeability coefficient (3.6 × 10^?8 cm²/s) than the pristine SPEEK membrane. Although the proton conductivity of the blend membranes decreased, a higher selectivity (ratio of the proton conductivity to the methanol permeability) was obtained than that of the pristine SPEEK membrane. The results showed that the SPEEK/TMBP/PN blend membranes could have potential use as proton‐exchange membranes in direct methanol fuel cells. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Properties of Sulfonated Poly(Arylene Ether Sulfone)/Functionalized Carbon Nanotube Composite Membrane for High Temperature PEMFCs

Composite membranes are prepared using sulfonated poly (arylene ether sulfone) (SPAES) copolymers and the incorporation of functionalized multiwall carbon nanotubes (CNTs) for high temperature (120 °C) proton exchange membrane fuel cells (PEMFCs). The CNT is functionalized with sulfonated groups that are expected to support the improvement of water absorption and mechanical properties. The SPAES copolymers are synthesized with sulfonation degree (DS) = 0.5 and the sulfonated CNT (s‐CNT) is dispersed into the SPAES copolymers in varying ratios to fabricate the composite membranes. In this study, the proton conductivity, water uptake, and single cell test of the composite membrane are investigated for verifying the effects of the enhancement at high temperature and low humidity. The composite membrane containing 0.2 wt.% s‐CNT increases proton conductivity approximately 45% at 120 °C and 50% relative humidity and enhances the tensile strength by about 1.3 times compared to the pristine membrane. However, the proton conductivity and water absorption shows a decline when more than 0.2 wt.% s‐CNT is added in the composite membrane, due to the aggregation of the s‐CNT, which serves as a proton barrier. For the single cell test, the developed composite membrane with 0.2 wt.% s‐CNT exhibits a notable performance for high temperature PEMFC.     

EB‐crosslinked Polymer Electrolyte Membranes Based on Highly Sulfonated Poly(ether ether ketone) and Poly(vinylidene fluoride)/Triallyl Isocyanurate

In this study, crosslinked polymer electrolyte membranes for polymer electrolyte membrane fuel cell (PEMFC) applications are prepared using electron beam irradiation with a mixture of sulfonated poly(ether ether ketone) (SPEEK), poly(vinylidene fluoride) (PVDF), and triallyl isocyanurate (TAIC) at a dose of 300 kGy. The gel‐fraction of the irradiated SPEEK/PVDF/TAIC (95/4.5/0.5) membrane is 87% while the unirradiated membrane completely dissolves in DMAc solvent. In addition, the water uptake of the irradiated membrane is 221% at 70 °C while that of the unirradiated membrane completely dissolves in water at above 70 °C. The ion exchange capacity and proton conductivity of the crosslinked membrane are 1.57 meq g⁻¹, and 4.0 × 10⁻² S cm⁻¹ (at 80 °C and RH 90%), respectively. Furthermore, a morphology study of the membranes is conducted using differential scanning calorimetry and X‐ray diffractometry. The cell performance study with the crosslinked membrane demonstrates that the maximum power density is 518 mW cm⁻² at 1036 mA cm⁻² and the maximum current density at applied voltage of 0.4 V is 1190 mA cm⁻².     

Effect of PES on the morphology and properties of proton conducting blends with sulfonated poly(ether ether ketone)

Development of alternate materials to Nafion, based on ionically conducting polymers and their blends is important for the wider applications of proton exchange membrane fuel cells. In this work, blends of sulfonated poly(ether ether ketone) (SPEEK) with poly(ether sulfone) (PES) are investigated. SPEEK with various ion exchange capacity (IEC) was prepared and blended with PES, which is nonionic and hydrophobic in nature. A comparative study of the water uptake, proton conductivity, and thermo‐mechanical characteristics of SPEEK and the blend membranes as a function of the IEC is presented. Addition of PES decreases the water uptake and conductivity of SPEEK. Chemical and thermal stability and mechanical properties of the membrane improve with the addition of PES. The effect of water content on the thermo‐mechanical properties of membranes was also studied. The morphology of blend membranes was studied using SEM to understand the microstructure and miscibility of the components. On the basis of the results, a plausible microstructure of the blends is presented, and is shown to be useful in understanding the variation of different properties with blending. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

DMFCs用SPEEK/SiOx-S复合质子交换膜

A sulfonated poly(ether ether ketone) (SPEEK) membrane with a fairly high degree of sulfonation (DS) can swell excessively and even dissolve at high temperature. To solve these problems, insolvable functionalized silica powder with sulfonic acid groups (SiOx-S) was added into the SPEEK matrix (DS 55.1%) to prepare SPEEK/ SiOx-S composite membranes. The decrease in both the swelling degree and the methanol permeability of the membranes was a dose-dependent result of addition of the SiOx-S powder. Pure SPEEK membrane swelled 52.6% at 80°C, whereas the SPEEK/SiOx-S (15%, by mass) membrane swelled only 27.3% at the same temperature. From room temperature to 80℃, all SPEEK/SPEEK/SiOx-S composite membranes had methanol permeability of about one order of magnitude lower than that of Nafion115. Compared with pure SPEEK membranes, the addition of the SiOx-S powder not only leads to higher proton conductivity, but also increases the dimensional stability at higher temperatures, and greater proton conductivity can be achieved at higher temperature. The SPEEK/SiOx-S (20%, by mass) membrane could withstand temperature up to 145°C, at which in 100% relative humidity (RH) its proton conductivity exceeded slightly that of Nafion115 membrane and reached 0.17 S•cm－1, while pure SPEEK mem-brane dissolved at 90°C. The SPEEK/SiOx-S composite membranes are promising for use in direct methanol fuel cells because of their good dimensional stability, high proton conductivity, and low methanol permeability.     

Sulfonated poly(ether sulfone)/phosphotungstic acid/attapulgite composite membranes for direct methanol fuel cells

Novel composite sulfonated poly(ether sulfone)(SPES)/phosphotungstic acid (PWA)/attapulgite (AT) membranes were investigated for direct methanol fuel cells (DMFCs). Physical–chemical properties of the composite membranes were characterized by FTIR, DSC, TGA, SEM‐EDX, water uptake, tensile test, proton conductivity, and methanol permeability. Compared with a pure SPES membrane, PWA, and AT doping in the membrane led to a higher thermal stability and glass transition temperature (T_g) as revealed by TGA and DSC. Tensile test indicated that lower AT content (3%) in the composite can significantly increase the tensile strength, while higher AT loading demonstrated a smaller contribution on strength. Proper PWA and AT loadings in the composite membranes can increase the proton conductivity and lower the methanol cross‐over. The proton conductivity of the SPES‐P‐A 10% composite membrane reached 60% of the Nafion 112 membrane conductivity at room temperature while the methanol permeability was only one‐fourth of that of Nafion 112 membrane. This excellent performances of SPES/PWA/AT composite membranes could indicate a potential feasibility as a promising electrolyte for DMFC. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and properties of bisphenol A‐based sulfonated poly(arylene ether sulfone) proton exchange membranes for direct methanol fuel cell

Novel bisphenol A‐based sulfonated poly(arylene ether sulfone) (bi A‐SPAES) copolymers were successfully synthesized via direct copolymerization of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenylsulfone, 4,4′‐dichlorodiphenylsulfone, and bisphenol A. The copolymer structure was confirmed by Fourier transform infrared spectra and ¹H NMR analysis. The series of sulfonated copolymers based membranes were prepared and evaluated for proton exchange membranes (PEM). The membranes showed good thermal stability and mechanical property. Transmission electron microscopy was used to obtain the microstructures of the synthesized polymers. The membranes exhibit increased water uptake from 8% to 66%, ion exchange capacities from 0.41 to 2.18 meq/g and proton conductivities (25°C) from 0.012 to 0.102 S/cm with the degree of sulfonation increasing. The proton conductivities of bi A‐SPAES‐6 membrane (0.10–0.15 S/cm) with high‐sulfonated degree are higher than that of Nafion 117 membrane (0.095–0.117 S/cm) at all temperatures (20–100°C). Especially, the methanol diffusion coefficients of membranes (1.7 × 10^?8 cm²/s–8.5 × 10^?7 cm²/s) are much lower than that of Nafion 117 membrane (2.1 × 10^?6 cm²/s). The new synthesized copolymer was therefore proposed as a candidate of material for PEM in direct methanol fuel cell. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Fluorenyl‐containing Quaternary Ammonium Poly(arylene ether sulfone)s for Anion Exchange Membrane Applications

A series of anion exchange membranes (AEM) based on block quaternary ammonium poly(arylene ether sulfone) (QA‐bPAES) were successfully synthesized from 9,9′‐bis(4‐hydroxyphenyl) fluorene, 4,4′‐(hexafluoroisopropylidene) diphenol and 4,4′‐difluorodiphenyl sulfone via block polymerization, chloromethylation, quaternization, alkalization and solution casting. Properties of the obtained QA‐bPAES membranes, including ion exchange capacity (IEC), water uptake, swelling ratios, methanol permeability and ion conductivity were investigated. The obtained QA‐bPAES membranes showed low water uptakes, high ion conductivities and good physical and chemical stability. For example, the membrane of QA‐bPAES(20/10)‐1.34 with IEC of 1.34 mmol g⁻¹ exhibited swelling ratios of 5.0% and 5.1% in in‐plane and through‐plane direction, respectively, and ion conductivity of 15.6 mS cm⁻¹ in water at 60 °C with low methanol permeability of 1.06 × 10⁻⁷ cm² s⁻¹ (25 °C). All the results indicated that this type of block membranes had good potentials for alkaline anion exchange membrane fuel cell applications.     

Sulfonated poly(arylene ether ketone)s prepared by direct copolymerization as proton exchange membranes: Synthesis and comparative investigation on transport properties

Sulfonated poly(aryl ether ketone)s (SPAEK) copolymers were synthesized by aromatic nucleophilic polycondensation from 3,3′, 5,5′‐tetramethyl‐4, 4′–biphenol, 1,4‐bis(4‐fluorobenzoyl) benzene, and disulfonated difluorobenzophenone. The SPAEK membranes did not exhibit excessive swelling in hot water and at the same time show the proton conductivities in the range of 0.030 S/cm to 0.099 S/cm at 80°C. The methanol diffusion coefficients of the SPAEK membranes were in the range of 4.7 × 10^?7 to 8.1 × 10^?7cm²/s measured at 25°C. The transport properties of this series of SPAEK copolymers were compared to poly(aryl ether ether ketone)s (SPEEK), poly(aryl ether ether ketone ketone)s (SPEEKK), and Nafion® membranes. It was found that the transport properties (including proton conductivity and methanol permeability) follows the trend of SPEEKK‐60 < SPAEK‐60 < SPEEK‐60 < Nafion® 117, the order of which is also attributed to the differences in the chemical structure of the polymers and the membrane morphology. In general, this novel series of SPAEK membranes possess various advantages, such as low cost of the initial monomers, high thermal and mechanical stability, and low methanol permeability while simultaneously possessing sufficient proton conductivity, which makes them notably promising as proton exchange membrane (PEM) materials in direct methanol fuel cell (DMFC) applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008