共查询到20条相似文献,搜索用时 390 毫秒
1.
2.
介绍了悬浮法PVC树脂聚合生产工艺技术、PVC浆料汽提生产工艺技术,通过分析温度、压力、停留时间对PVC浆料汽提效果的影响因素,结合汽提塔工艺计算的具体数据,对汽提系统浆料管线配管、汽提塔配管的设计方面提出改进方法和建议,并对今后PVC浆料汽提过程设计中应注意的问题进行论证并提出注意事项和意见。 相似文献
3.
4.
将锦石化供排水厂含硫污水汽提塔与单塔加压侧线抽出汽提工艺相比较 ,指出其存在的问题 ,进而提出改造设计 ,并指出单塔加压侧线抽出汽提工艺是发展方向。 相似文献
5.
依据常减压蒸馏装置减压深拔现状及研究动态,结合8.0 Mt/a常减压蒸馏装置设计实例,分析了为实现减压深拔目标减压系统所采用的工艺技术,包括较高的加热炉出口温度、减压炉防结焦、减压塔塔顶高真空度和全塔低压降、微湿式带汽提操作、减压塔塔底防结焦等工艺,并重点讨论了过气化油流程设置对减压深拔的影响。 相似文献
6.
《化工科技》2016,(6)
酸性水汽提装置是炼油厂重要的环保装置,随着装置大型化与进口原料油硫含量的逐步升高及环保标准的逐步严格,酸性水处理和利用日益受到重视。介绍了中国石油吉林石化公司炼油厂利用单塔加压侧线汽提工艺对酸性水综合利用的方法,单塔加压侧线汽提工艺的工艺原理、工艺流程、消耗定额,汽提塔塔顶酸性气送至硫磺回收装置进行硫磺回收利用,汽提塔侧线得到的粗氨焚烧后放空。经过单塔加压侧线汽提工艺处理所得的净化水COD降到300mg/L以下,氨氮、硫化氢质量分数都在40μg/g以下,净化水回用率达到52%以上,净化污水的排放达到环保要求,利用单塔加压侧线汽提工艺炼油厂酸性水实现了综合利用。 相似文献
7.
运用Aspen Plus流程模拟软件,对单塔加压、侧线抽出工艺的酸性水汽提塔进行模拟,通过热进料位置、冷进料比例、侧线抽出位置及侧线抽出量的分析,确定汽提塔操作参数,对汽提塔设计提供指导。 相似文献
8.
文章通过分析茂石化各蒸馏装置减压深拔的现状,指出影响减压拔出率的主要因素是加热炉出口温度及减压塔汽化段真空度,指出了提高装置设计水平和工艺操作水平是提高减压深拔的关键。设计上町通过增加抽真空级数.并增加急冷油,降低塔底温度,以及通过减压炉管逐级扩径,减小转油线温降等方法,尽可能提高减捱炉出口温度实现深拔;工艺操作上可通过调整炉管注汽和塔底吹汽,调整各回流降低塔顶温度,调整冷却水降最降低冷后温度,适当提高常压炉温度减少减压负荷,从而达到提高减压拔出率的目的。 相似文献
9.
催化剂汽提器内气固传质特性的研究 总被引:13,自引:0,他引:13
采用氧气示踪的方法在f 486×8000mm的有机玻璃床内对普通流化床汽提器和盘环形挡板汽提器进行了系统的气固相传质冷态模拟实验,得出了不同汽提线速和催化剂质量流率下上述两种催化剂汽提器内油气浓度轴向分布的变化规律。根据其油气浓度轴向分布的特点,结合鼓泡流化床两相理论以及一系列的假设,提出了针对这两种汽提器的一维传质模型。由实验结果待定了一维传质模型的模型参数,获得了计算两种汽提器轴向油气浓度分布的半经验的指数关联式。该关联式和实验数据比较吻合,相对误差均在10%以内。由该关联式可进一步计算出汽提器的汽提效率,可以为工业汽提器工艺参数的优化以及工程设计提供参考。 相似文献
10.
分析了影响尿素装置氨汽提塔汽提效率的因素,并结合实际生产总结经验,优化操作,改善氨汽提塔工况,提高汽提效率。 相似文献
11.
以正丙醇-异丙醇体系为例,研究了带有侧线采出回流的部分透热精馏操作。在该操作中,精馏段侧线采出气相,经塔外冷凝后回流至塔内采出板上方;提馏段某塔板被同轴的夹套式中间再沸器环绕,侧线采出该板处的气相回流至塔内采出板上方。通过单因素分析和响应面法对精馏段和提馏段操作的相关工艺参数分别进行了模拟优化,并对相应操作的热力学性能和分离性能的变化进行了分析。最终优化结果表明:达到规定的分离效果,带有侧线采出回流的部分透热精馏相较于绝热精馏有效能损失降低了26.5%。带有侧线采出回流的部分透热精馏操作通过合理分配能量、降低对热剂和冷剂的品位要求和提高能量利用率,最终达到节能目的。 相似文献
12.
Sour water containing hydrogen sulfide, carbon dioxide, hydrogen cyanide, and ammonia is mainly purified by steam stripping.
Increased concern in recent times over effluent water quality and energy saving has caused sour water stripping to attract
considerable attention. However, the development of the operation methodology and structure of this process has not been systemic,
leading to inefficiencies in the systems commonly used. In this paper, the characteristics of a sour water stripping column
are investigated by using an industrial-scale simulation. From these results, we propose several guidelines (high feed temperature,
low composition of CO2 in the feed, need of rectifying section, low mass flow rate of the second recycle stream, high reflux ratio, and modified
structure using a pump-around side cooler) for improving stripper performance through changes in the operating condition and
process structure. The proposed structure and guidelines can be applied not only to reduce steam consumption and lower the
ammonia concentration in the effluent water but also to operate the system stably. 相似文献
13.
Treating Methanol‐to‐Olefin Quench Water by Minihydrocyclone Clarification and Steam Stripper Purification 下载免费PDF全文
In the chemical industry, methanol‐to‐olefin (MTO) technology is a novel process for producing ethylene and propylene from naphtha thermal cracking. The process of recovering MTO quench water by minihydrocyclone and steam stripping treatment was successfully applied in industrial plants. The fine catalyst in the quench water is removed by the two‐stage minihydrocyclone separation. The method and equipment for this system present various advantages: the quench water can be recycled in the cooling system and prevents heat loss in heat transfer systems; and the stripping tower can be blocked by the catalyst. Maintenance activities are reduced and a stable operation cycle is extended. The proposed treatment process improves the economic efficiency of the MTO device. 相似文献
14.
15.
16.
Leland M. Vane Franklin R. Alvarez Yu Huang Richard W. Baker 《Journal of chemical technology and biotechnology (Oxford, Oxfordshire : 1986)》2010,85(4):502-511
BACKGROUND: The energy demand of distillation‐based systems for ethanol recovery and dehydration can be significant, particularly for dilute solutions. An alternative separation process integrating vapor stripping with a vapor compression step and a vapor permeation membrane separation step, termed membrane assisted vapor stripping (MAVS), has been proposed. The hydrophilic membrane separates the ethanol–water vapor into water‐rich permeate and ethanol‐enriched retentate vapor streams from which latent and sensible heat can be recovered. The objective of this work was to demonstrate experimentally the performance of a MAVS system and to compare the observed performance with chemical process simulation results using a 5 wt% ethanol aqueous feed stream as the benchmark. RESULTS: Performance of the steam stripping column alone was consistent with chemical process simulations of a stripping tower with six stages of vapor liquid equilibria (VLE). The overhead vapor from the stripper contained about 40 wt% ethanol and required 6.0 MJ of fuel‐equivalent energy per kg of ethanol recovered in the concentrate. Introduction of the vapor compressor and membrane separation unit and recovery of heat from both membrane permeate and retentate streams resulted in a retentate ethanol concentrate containing ca 80 wt% ethanol, but requiring only 2.2 MJ fuel kg?1 ethanol, significantly less than steam stripping alone. CONCLUSION: Performance of the experimental unit with a 5 wt% ethanol feed liquid corroborated chemical process simulation predictions for the energy requirement of the MAVS system, demonstrating a 63% reduction in the fuel‐equivalent energy requirement for MAVS compared with conventional steam stripping or distillation. Published 2009 by John Wiley & Sons, Ltd. 相似文献
17.
水力喷射空气旋流器(water-sparged aerocyclone,WSA)是一种利用液体射流在气体旋流场中雾化强化气液传质的新型传质设备,可广泛用于废水、废气处理等环境工程中。为了改进水力喷射空气旋流器结构,提高其气液传质性能,本文通过废水氨氮吹脱实验研究了进气口轴向位置以及底部挡板的设置对气液传质性能的影响。实验结果表明,进气位置与底部挡板对水力喷射空气旋流器的气液传质性能存在影响。在相同工作条件下,气相进口沿轴向下移对WSA内气液传质性能作用较小,但能够使其气相压降降低约为10%。在WSA主筒体底部液封区域设置挡板,能够强化WSA底部气液两相的混合,进而提高低液相循环流量下WSA内的气液传质性能,且随进气速度的增加,其效果越显著,研究结果可为设计传质性能良好的WSA提供设计依据。 相似文献
18.
针对传统的精馏法、结晶法及刮膜蒸发法脱酚工艺存在的诸多弊端,有必要对新的脱酚工艺进行研究,以制备超低游离酚质量分数的聚碳级双酚A。鉴于双酚A-苯酚物系高沸点、热敏性特性,文中以降膜蒸发脱除大部分苯酚、获得的粗双酚A为原料,采用向真空填料塔通入过热水蒸气进行气提的方法,研究制备超低游离酚质量分数聚碳级双酚A的脱酚工艺。研究结果表明:气提塔的操作压力、水蒸气温度和流量对脱酚效果有很大的影响。操作压力越低,组分间相对挥发度增大,脱酚效果越好。但过低的压力对脱酚效果的改善将不明显,带来的负面影响是设备投资的增加;水蒸气温度越高,塔内物料温度也随之升高,苯酚的饱和蒸汽压增大,脱酚效果越好;水蒸气流量越大,在操作压力不变的情况下,苯酚的气相分压就越低,脱酚效果越好。适宜的工艺条件是:操作压力为4.0—5.0 kPa;气提水蒸气温度185—190℃,流量为处理量的2%。 相似文献
19.
为了降低空气低温分离过程的设备投资和能耗,在分析空分体系的热力学性质及流程特点的基础上,提出了一种新型的隔壁式空分精馏塔流程。应用Aspen Plus模拟软件,对空气分离的传统流程和隔壁塔流程进行了模拟对比,考察了隔壁式空分精馏塔各结构参数与操作参数对其年总成本的影响,并分析比较了空分传统流程和隔壁式空分精馏塔流程的热力学效率。结果表明,隔壁式空分精馏塔的建模合理可行,通过年总成本优化得到了该隔壁塔的最优结构参数与操作参数,分别为:液氧流量为3 kmol/h,气相分配比(体积比)为0.05,精馏段理论板数为33,侧线精馏段理论板数为30,公共提馏段理论板数为22。与传统空分流程相比,隔壁式空分精馏塔流程的有效能损失降低并且在热力学效率方面高出4.7%。 相似文献