0.13-μm CMOS Phase Shifters for X-, Ku-, and K-Band Phased Arrays

Two 4-bit active phase shifters integrated with all digital control circuitry in 0.13-mum RF CMOS technology are developed for X- and Ku-band (8-18 GHz) and K-band (18-26 GHz) phased arrays, respectively. The active digital phase shifters synthesize the required phase using a phase interpolation process by adding quadrature-phased input signals. The designs are based on a resonance-based quadrature all-pass filter for quadrature signaling with minimum loss and wide operation bandwidth. Both phase shifters can change phases with less than about 2 dB of RMS amplitude imbalance for all phase states through an associated DAC control. For the X- and Ku-band phase shifter, the RMS phase error is less than 10^o over the entire 5-18 GHz range. The average insertion loss ranges from to at 5-20 GHz. The input for all 4-bit phase states is typically at -5.4 plusmn1.3 GHz in the X- and Ku-band phase shifter. The K-band phase shifter exhibits 6.5-13 of RMS phase error at 15-26 GHz. The average insertion loss is from 4.6 to at 15-26 GHz. The input of the K-band phase shifter is at 24 GHz. For both phase shifters, the core size excluding all the pads and the output 50 Omega matching circuits, inserted for measurement purpose only, is very small, 0.33times0.43 mm² . The total current consumption is 5.8 mA in the X- and Ku-band phase shifter and 7.8 mA in the K-band phase shifter, from a 1.5 V supply voltage.     

A Ku‐Band 5‐Bit Phase Shifter Using Compensation Resistors for Reducing the Insertion Loss Variation

This paper describes the performance of a Ku‐band 5‐bit monolithic phase shifter with metal semiconductor field effect transistor (MESFET) switches and the implementation of a ceramic packaged phase shifter for phase array antennas. Using compensation resistors reduced the insertion loss variation of the phase shifter. Measurement of the 5‐bit phase shifter with a monolithic microwave integrated circuit demonstrated a phase error of less than 7.5° root‐mean‐square (RMS) and an insertion loss variation of less than 0.9 dB RMS for 13 to 15 GHz. For all 32 states of the developed 5‐bit phase shifter, the insertion losses were 8.2 ± 1.4 dB, the input return losses were higher than 7.7 dB, and the output return losses were higher than 6.8 dB for 13 to 15 GHz. The chip size of the 5‐bit monolithic phase shifter with a digital circuit for controlling all five bits was 2.35 mm × 1.65 mm. The packaged phase shifter demonstrated a phase error of less than 11.3° RMS, measured insertion losses of 12.2 ± 2.2 dB, and an insertion loss variation of 1.0 dB RMS for 13 to 15 GHz. For all 32 states, the input return losses were higher than 5.0 dB and the output return losses were higher than 6.2 dB for 13 to 15 GHz. The size of the packaged phase shifter was 7.20 mm × 6.20 mm.     

2.4 GHz continuously variable ferroelectric phase shifters using all-pass networks

Continuously variable ferroelectric (BST on sapphire) phase shifters based on all-pass networks are presented. An all-pass network phase shifter consists of only lumped LC elements, and thus the total size of the phase shifter is kept to less than 2.2 mm /spl times/ 2.6 mm at 2.4 GHz. The tunability (C/sub max//C/sub min/) of a BST interdigital capacitor is over 2.9 with a bias voltage of 140 V. The phase shifter provides more than 121/spl deg/ phase shift with the maximum insertion loss of 1.8 dB and the worst case return loss of 12.5 dB from 2.4 GHz to 2.5 GHz. By cascading two identical phase shifters, more than 255/spl deg/ phase shift is obtained with the maximum insertion loss of 3.75 dB. The loss figure-of-merit of both the single- and double-section phase shifters is over 65/spl deg//dB from 2.4 GHz to 2.5 GHz.     

An X-band 22.5°/45° digital phase shifter based on switched filter networks

The design approach and performance of a 22.5°/45°digital phase shifter based on a switched filter network for X-band phased arrays are described. Both the MMIC phase shifters are fabricated employing a 0.25μm gate GaAs pHEMT process and share in the same chip size of 0.82×1.06 mm². The measurement results of the proposed phase shifters over the whole operating frequency range show that the phase shift error is less than 22.5°±2.5°, 45°±3.5°, which shows an excellent agreement with the simulated performance, the insertion loss is within the range of 0.9-1.2 dB for the 22.5°phase shifter and 0.9-1.4 dB for the 45°phase shifter, and the input/output return loss is better than -12.5 and -11 dB respectively. They also achieve the similar P_1dB continuous wave power handing capability of 24.8 dBm at 10 GHz. The phase shifters show a good phase shift error, insertion loss and return loss in the X-band (40%), which can be employed into the wide bandwidth multi-bit digital phase shifter.     

Design and performance of a Ka-band monolithic phase shifterutilizing nonresonant FET switches

This paper describes design consideration and performance of a Ka-band monolithic phase shifter utilizing nonresonant FET switches. The switches show broad-band on/off characteristics up to 60 GHz without using inductors; thus, robust circuit design is possible for a switched-line phase shifter. To determine circuit topology, we introduce a schematic design approach. As a result, desired phase shift as well as good matching characteristics can be realized. The developed 4-bit monolithic phase shifter demonstrates an overall phase deviation less than 5° rms and an insertion loss variation less than 0.65 dB rms from 33 to 35 GHz. For all 16 states, the insertion loss is measured to be 13.1±1.1 dB and the VSWR is less than 1.6. The chip size of the monolithic phase shifter is 2.5 mm×2.2 mm     

基于GaN HEMT工艺的高功率宽带6 bit数字移相器

基于GaN HEMT工艺研制了一款8～12.5 GHz宽带6 bit数字移相器.通过采用优化的宽带拓扑和集总元件,以及在片上集成GaN并行驱动器,提高了移相精度,缩小了芯片的尺寸,减少了控制端数量.测试结果表明,在8～12.5 GHz频带内,全部64个移相状态下,插入损耗小于11 dB,输入回波损耗小于-14 dB,输出回波损耗小于-16 dB,移相均方根误差小于1.8°,幅度变化均方根误差小于0.5 dB.在8 GHz频率下,1 dB压缩点输入功率高达33 dBm.芯片尺寸为5.05 mm×2.00 mm×0.08 mm.     

一种S频段反射型可调模拟移相器的设计

设计了一种应用于S频段卫星通信相控阵系统的反射型可调模拟移相器。该移相器利用三分支线定向耦合器扩展了带宽,改善了工作频段内驻波;采用传输线和变容二极管构成的L型反射负载扩大了相移量。测试结果表明,在上行频段1.98～2.01 GHz内,相移量达到191°±1°,在下行频段2.17～2.2 GHz内,相移量达到186°±0.1°;插入损耗优于3.3 dB且插入损耗波动小于1 dB,回波损耗在整个电压调谐范围内均大于20 dB。该移相器结构简单、便于调节且价格低廉,在卫星通信领域有一定的应用价值。     

Analysis and numerical simulation of a Ku-band analog reflection phase shifter based on radio-frequency microelectromechanical varactors

The topology of a Ku-band reflection phase shifter with microelectromechanical varactors as tunable elements is presented. The phase shifter dimensions are 4 × 4.85 mm. Its calculated operating frequency is 14 GHz, the 1-dB-loss bandwidth is 700 MHz, and the phase shift over the bandwidth is no less than 145 deg.     

Millimeter-Wave Reflective-Type Phase Shifter in CMOS Technology

The design and measurement of a compact, wide-band reflective-type phase shifter in 90 nm CMOS technology in V-band frequency is presented. This phase shifter has a fractional bandwidth of 26% and an average insertion loss of 6 dB over all phase states. The chip area is only 0.08 mm $^{2}$. Measurement results show that the developed phase shifter provides 90$^{circ}$ continuous phase shift over the frequency range of 50–65 GHz. The measured return loss is greater than 12 dB at 50 GHz. The output power is linear up to at least 4 dBm input power.      

一种6~18 GHz宽带高精度有源移相器

设计了一种6 bit 6~18 GHz工作频段的宽带高精度有源移相器。片上集成了输入无源巴伦、逻辑编码器、RC多相滤波器、矢量合成单元、数控单元等。该移相器的设计采用55 nm CMOS工艺实现,芯片尺寸为1.29 mm×0.9 mm,移相器核心尺寸为1.02 mm×0.58 mm。后仿结果表明,在6~18 GHz频率范围内,增益误差RMS值小于1 dB,相位误差RMS值小于0.75°,输入回波损耗、输出回波损耗分别小于-8.5 dB、-8.9 dB,芯片总功耗为20.7 mW。该6 bit移相器的相对带宽为100%,覆盖C、X和Ku波段,适用于雷达探测等领域。     

A low-cost 8 to 26.5 GHz phased array antenna using a piezoelectrictransducer controlled phase shifter

A new phased array antenna of wide bandwidth and good beam scanning angle has been developed using a low cost multiline phase shifter controlled by a piezoelectric transducer (PET) and a stripline fed Vivaldi antenna array. The multiline progressive PET phase shifter has a low perturbation loss of less than 2 dB and a total loss of less than 4 dB up to 40 GHz with a maximum phase shift of 480°. The proposed phased array antenna consists of four E- or H-plane Vivaldi antennas, a PET phase shifter, and a power divider. The phased array shows a wide beam scanning capability of ±27° over a wide bandwidth from 8 to 26.5 GHz covering X, Ku, and K bands     

An MMIC active phase shifter using a variable resonant circuit [andMESFETs]

This paper describes a monolithic-microwave integrated-circuit (MMIC) active phase shifter using a variable resonant circuit with a large amount of variable phase. We first propose a novel active phase-shifter configuration that uses a variable resonant circuit with second-order all-pass network characteristics. Phase can be changed with a constant amplitude by varying the capacitance or the inductance of the resonant circuit. Next, an experimental MMIC active phase shifter with input active matching is presented. A phase shift of over 100° and an insertion loss of 4±1 dB are obtained from 2.2 to 2.8 GHz. The chip size is less than 1.0 mm². Finally, an experimental 360° MMIC active phase shifter is presented. Over the bandwidth of 40 MHz at 2.44 GHz, the insertion gain is 2.0±0.7 dB and the phase error is within ±4° when measured in 30° steps     

开关线型四位数字MEMS移相器

介绍了一种基于射频微机械串联开关设计的开关线型四位数字微机电系统(M icro-e lectrom echan ica lSystem s以下简称M EM S)移相器。该移相器集成了16个RF M EM S开关,使用了13组四分之一波长传输线和M IM接地耦合电容,有效地使开关的驱动信号和微波信号隔离,串联容性开关设计有效地降低了开关的启动电压。使用低温表面微机械工艺在360μm厚的高阻硅衬底上制作移相器,芯片尺寸4.8 mm×7.8 mm。移相器样品在片测试结果表明,频点10.1 GH z,22.5°相移位的相移误差为±0.4,°插损2.8 dB;45°位的相移误差为±1.1,°插损2.0 dB;在X波段,对16个相移态的测试结果表明,移相器的插入损耗小于4.0 dB,驻波比小于2.4,开关驱动电压为17~20 V。     

A hybrid phase shifter circuit based on TlCaBaCuO superconductingthin films

A superconductor-semiconductor hybrid reflection-type phase shifter circuit has been designed, fabricated, and characterized for 180° phase bit with center frequency of 4 GHz and bandwidth of 0.5 GHz for operation at 77 K. All of the passive components of the phase shifter circuit such as input/output feed lines, 3 dB Lange coupler, impedance matching networks, and transmission lines consisted of thallium based superconducting TlCaBaCuO thin films of 4000 Å thickness on lanthanum aluminate substrate. Metal-Schottky field-effect-transistors (MESFET's) on GaAs semiconductor were used as active devices for switching action (on-state and off-state) in the phase shifter circuit. The phase shift and insertion losses were investigated as a function of frequency from 3.6 to 4.6 GHz at 77 K. The circuit exhibited a fairly flat response of 180° phase shift with a maximum deviation of less than 2° and a maximum insertion loss of 2 dB for on-state and 2.2 dB for off-state conditions over 0.5 GHz bandwidth at 4 GHz. The insertion losses were also fairly flat within the bandwidth. The insertion losses were constant between 50 and 80 K, giving the circuit a large range of operation at or below 77 K. The performance of this circuit as compared to a gold microstrip-semiconductor circuit designed identically was superior by a factor of 1.5, and may be due to lower conductor losses and lower surface resistance in the superconducting microstrips     

Optimum field theory design of broad-band E-plane branchguide phase shifters and 180° couplers

Optimum rectangular waveguide E-plane branch guide phase shifters and 180° branch guide couplers are designed with the rigorous method of field expansion into normalized eigenmodes. The design includes both the higher order mode interaction between the step discontinuities and the finite step and branch heights. The phase shifter design applies the Schiffman principle to branch guide couplers where two ports are short-circuited. The 180° coupler design combines the advantage of the broadband potential of multiple-branch couplers with the low-insertion-loss qualities of E-plane stub-loaded phase shifters. A computer-optimized phase shifter prototype for the waveguide Ku-band (12-18 GHz) shows a 90°±1° differential phase shift with reference to an empty waveguide within about 23% bandwidth. Five-branch three-stub coupler prototypes, designed for 3±0.2 dB coupling, for the waveguide Ku- and Ka-bands (26-40 GHz) achieve a 180°±1° differential phase shift at the output ports within about 19% bandwidth, as well as more than 30 dB isolation and return loss. The theory is verified by measured results     

Ultra compact, low loss, varactor tuned phase shifter MMIC atC-band

This paper presents a high yield, ultra compact, low loss phase shifter MMIC, realized with a commercial 0.6 μm GaAs MESFET process. Phase shift is enabled by varying the varactor capacitances of the lumped element equivalent of a transmission line. Continuously adjustable phase control over 90° is achieved from 4 GHz up to 6 GHz, with a loss of less than 2.2 dB. At 5.2 GHz, a loss of 1.2 dB and a loss variation of ±0.5 dB is measured. Phase and loss variations for several circuits from different wafers are within ±1° and ±0.1 dB, respectively, indicating low dependences on process variations. The phase shifter requires a circuit size of only 0.2 mm², which to our knowledge is the smallest size for a continuously adjustable passive phase shifter with comparable performance, reported to date     

毫米波RF-MEMS单片集成0/π移相器

介绍了一种毫米波RF-MEMS单片集成反射型0/Π移相器的设计、制造和测试.实测性能与设计结果吻合较好,达到的电性能指标为:在35GHz-38GHz频率范围内,电压驻波比小于1.8,参考态插入损耗为3.5±1.0dB,相移态插入损耗为2.0±0.6dB,相移为180°±6°.芯片尺寸:2.6mm×2.1mm×0.2mm.满足了插损低并具有电路拓扑的要求.     

A 4-bit CMOS Phase Shifter Using Distributed Active Switches

This paper presents a novel 4-bit phase shifter using distributed active switches in 0.18-mum RF CMOS technology. The relative phase shift, which varies from 0deg to 360deg in steps of 22.5deg, is achieved with a 3-bit distributed phase shifter and a 180deg high-pass/low-pass phase shifter. The distributed phase shifter is implemented using distributed active switches that consist of a periodic placement of series inductors and cascode transistors, thereby obtaining linear phase shift versus frequency with a digital control. The design guideline of the distributed phase shifter is presented. The 4-bit phase shifter achieves 3.5 plusmn 0.5 dB of gain, with an rms phase error of 2.6deg at a center frequency of 12.1 GHz. The input and output return losses are less than -15 dB at all conditions. The chip size is 1880 mum times 915 mum including the probing pads.     

A Full-360° Reflection-Type Phase Shifter With Constant Insertion Loss

A new reflection-type phase shifter with a full 360deg relative phase shift range and constant insertion loss is presented. This feature is obtained by incorporating a new cascaded connection of varactors into the impedance-transforming quadrature coupler. The required reactance variation of a varactor can be reduced by controlling the impedance ratio of the quadrature coupler. The implemented phase shifter achieves a measured maximal relative phase shift of 407deg, an averaged insertion loss of 4.4 dB and return losses better than 19 dB at 2 GHz. The insertion-loss variation is within plusmn0.1 and plusmn0.2 dB over the 360deg and 407deg relative phase shift tuning range, respectively.     

A new Millimeter-wave printed dipole phased array antenna using microstrip-fed coplanar stripline tee junctions

A new millimeter-wave printed twin dipole phased array antenna is developed at Ka band using a new microstrip-fed CPS tee junction, which does not require any bonding wires, air bridges, or via holes. The phased array used a piezoelectric transducer (PET) controlled tunable multitransmission line phase shifter to accomplish a progressive phase shift. A progressive phase shift of 88.8/spl deg/ is achieved with the 5 mm of perturber length when the PET has full deflection. Measured return loss of the twin dipole antenna is better than 10 dB from 29.5 to 30.35 GHz. Measured return loss of better than 15 dB is achieved from 30 to 31.5 GHz for a 1/spl times/8 phased array. The phased array antenna has a measured antenna gain of 14.4 dBi with 42/spl deg/ beam scanning and has more than 11 dB side lobe suppression across the scan.