ECR-PECVD方法低温制备多晶硅薄膜

采用ECR-PECVD低温沉积方法,以质量分数为5%的SiH4(配Ar气,SiH4:Ar=1:19)和H2为反应气体,在普通玻璃和单晶硅片衬底上直接沉积多晶硅薄膜,以期寻找到适合大规模工业化生产的方法.当衬底温度为500℃时,即能沉积高质量的多晶硅薄膜.沉积前,H2等离子体的清洗时间和流量对多晶薄膜的质量有较大的影响.通过与其他反应气体相比较,我们制备的多晶硅薄膜不含杂质.     

用SiH2Cl2沉积MEMS中的多晶硅薄膜研究

用SiH2Cl2在3种温度下进行了多晶硅薄膜的沉积,根据膜厚计算出了沉积速率,用SEM、XRD和薄膜应力测试仪对薄膜进行测试分析.证明用SiH2Cl2在950℃时可以快速沉积用于MEMS的多晶硅.     

镀铜玻璃衬底上柱状多晶硅薄膜的制备

采用热丝化学气相沉积方法在镀铜玻璃衬底上制备了柱状多晶硅薄膜.使用XRD、Raman光谱、扫描电子显微镜(SEM)和原子力显微镜(AFM)等测试手段研究了灯丝与衬底间距(5～10 mm)、灯丝温度(1 800～1 500℃)以及对应的衬底温度(在320～200℃变化)对多晶硅薄膜的微观形貌、结晶性及晶体学生长方向的影响规律.研究结果表明:在镀铜玻璃衬底上金属诱导生长的多晶硅薄膜具有较高的晶化率,较低的晶化温度,同时铜过渡层影响多晶硅薄膜的晶体学生长方向.     

热丝化学气相沉积制备多晶硅薄膜的研究

采用热丝化学气相沉积技术制备了多晶硅薄膜。利用Raman、XRD、SEM等检测手段,系统研究了沉积气压、衬底温度、衬底与热丝间距离、衬底种类等实验参数对多晶硅薄膜晶态比、晶面择优取向、晶粒尺寸的影响。得出优化条件:沉积气压42 Pa,衬底温度250℃,衬底与热丝间距离48 mm,在玻璃衬底上制备出晶态比Xc>90%,择优取向为(111),横向晶粒尺寸为200~500 nm,纵向晶粒尺寸为30 nm左右的优质多晶硅薄膜。     

用ECR-PECVD低温沉积多晶硅薄膜

在自行设计研制的先进的电子回旋共振（ECR）等离子体增强化学气相沉（PECVD）装置上,采用ECR-PECVD可控活化低温外延技术,以SiH4＋H2为气源,硅和普通玻璃为衬底,低温（小于等于550℃）制备多晶硅（poly-Si）薄膜。利用反射高能电子衍射、透射电子显微镜和原子力显微镜研究了SiH4流量、H2流量和衬底温度等工艺参数的改变对薄膜晶化的影响。通过分析薄膜结构和形貌,得出适宜低温生长多晶硅薄膜的工艺参数。     

多晶硅薄膜的高温压阻效应

利用LPCVD制备重掺杂多晶硅薄膜,在0～560℃温度范围内对薄膜的压阻效应进行研究,同时对多晶硅薄膜应变系数随温度的变化,以及薄膜的淀积温度与薄膜厚度对应变系数的影响进行了相关的实验研究.结果表明,利用多晶硅材料制作的压敏电阻,其最高工作温度可以达到560℃以上.     

多晶硅薄膜的高温压阻效应

利用LPCVD制备重掺杂多晶硅薄膜,在0～560℃温度范围内对薄膜的压阻效应进行研究,同时对多晶硅薄膜应变系数随温度的变化,以及薄膜的淀积温度与薄膜厚度对应变系数的影响进行了相关的实验研究.结果表明,利用多晶硅材料制作的压敏电阻,其最高工作温度可以达到560℃以上.     

表面处理对低成本多晶硅太阳电池性能的影响

通过沉积SiNx薄膜和H2退火表面处理工艺对低成本多晶硅太阳电池进行了处理,对表面处理前后的电池效率进行了对比测试,详细地研究了这两种表面处理工艺对电池的短路电流、开路电压、填充因子和转换效率的影响。实验发现,沉积了SiNx薄膜的低成本多晶硅太阳电池的效率在原有基础上提高了1.8%左右;而经过H2退火后的电池效率则出现了效率衰减。与此同时,对成本相对高的太阳能级多晶硅电池也进行了H2退火,与低成本多晶硅电池相比,其效率增加明显,与低成本太阳电池呈现了相反的现象。最后分析了两种表面处理工艺对电池性能造成影响的原因。     

纳米多晶硅薄膜压力传感器制作及特性

给出一种纳米多晶硅薄膜压力传感器,采用LPCVD法在衬底温度620℃时制备纳米多晶硅薄膜,基于MEMS技术在方形硅膜不同位置制作由4个薄膜厚度为63.0nm的掺硼纳米多晶硅薄膜电阻构成惠斯通电桥结构,实现对外加压力的检测. 实验结果表明,当硅膜厚度75μm时,纳米多晶硅薄膜压力传感器在恒压源5.0V供电时,满量程（160kPa）输出为24.235mV,灵敏度为0.151mV/kPa,精度为0.59%F.S,零点温度系数和灵敏度温度系数分别为-0.124%/℃和-0.108%/℃.     

纳米多晶硅薄膜压力传感器制作及特性

给出一种纳米多品硅薄膜压力传感器,采用LPCVD法在衬底温度620℃时制备纳米多晶硅薄膜,基于MEMS技术在方形硅膜不同位置制作由4个薄膜厚度为63.0nm的掺硼纳米多晶硅薄膜电阻构成惠斯通电桥结构,实现对外加压力的检测.实验结果表明.当硅膜厚度75μm时,纳米多晶硅薄膜压力传感器在恒压源5.0V供电时,满量程(160kPa)输出为24.235mV,灵敏度为0.151mV/kPa,精度为0.59%F.S,零点温度系数和灵敏度温度系数分别为-0.124%/℃和-0.108%/℃.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Nanoimprint Lithography -A Next Generation High Volume Lithography Technique

IntroductionNanoimprint Lithography is a well-acknowl-edged low cost, high resolution, large area pattern-ing process. It includes the most promising methods,high-pressure hot embossing lithography (HEL) [2],UV-cured imprinting (UV-NIL) [3] and micro contactprinting (m-CP, MCP) [4]. Curing of the imprintedstructures is either done by subsequent UV-lightexposure in the case of UV-NIL or by cooling downbelow the glass transition temperature of the ther-moplastic material in case of HEL…     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

Influence of PVK ： NPB hole transporting layer on the characteristics of organic light-emitting devices

A doping system consisting of NPB and PVK is employed as a composite hole transporting layer （CHTL）. By adjusting the component ratio of the doping system, a series of devices with different concentration proportion of PVK ： NPB are constracted. The result shows that doping concentration of NPB enhances the competence of hole transporting ability, and modifies the recombination region of charge as well as affects the surface morphology of doped film. Optimum device with a maximum brightness of 7852 cd/m^2 and a power efficiency of 1.75 lm/W has been obtained by choosing a concentration proportion of PVK ： NPB at 1：3.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.     

Analysis of error performance on Turbo coded FDPIM

Due to variable symbol length of digital pulse interval modulation（DPIM）, it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation（FDPIM） method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.