Electrochemical characteristics of cobalt-substituted lithium nickel oxides synthesized from lithium hydro-oxide and nickel and cobalt oxides

LiNi_1−yCo_yO₂ (y=0.1, 0.3 and 0.5) were synthesized by solid state reaction method at 800 °C and 850 °C from LiOH·H₂O, NiO and Co₃O₄ as starting materials. The electrochemical properties of the synthesized LiNi_1−yCo_yO₂ were investigated. As the content of Co decreases, particle size decreases rapidly and particle size distribution gets more homogeneous. When the particle size is compared at the same composition, the particles synthesized at 850 °C are larger than those synthesized at 800 °C. LiNi_0.7Co_0.3O₂ synthesized at 850 °C has the largest intercalated and deintercalated Li quantity Δx among LiNi_1−yCo_yO₂ (y=0.1, 0.3 and 0.5). LiNi_0.7Co_0.3O₂ synthesized at 850 °C has the largest first discharge capacity (178 mAh/g), followed by LiNi_0.7Co_0.3O₂ (162 mAh/g) synthesized at 800 °C. LiNi_0.7Co_0.3O₂ synthesized at 800 °C has discharge capacities of 162 and 125 mAh/g at n=1 and n=5, respectively.     

Synthesis of spherical shape borate-based bioactive glass powders prepared by ultrasonic spray pyrolysis

Spherical shape borate-based bioactive glass powders with fine size were directly prepared by high temperature spray pyrolysis. The powders prepared at temperatures between 1200 and 1400 °C had mixed phase with small amounts of fine crystal and an amorphous rich phase. Glass powders with amorphous phase were prepared at a temperature of 1500 °C. The mean size of the glass powders prepared by spray pyrolysis was 0.76 μm. The glass powders prepared at a temperature of 1200 °C had two distinct exothermic peaks (T_c1 and T_c2) at temperatures of 588 and 695 °C indicating crystallization. The glass transition temperature (T_g) of the powders prepared at a temperature of 1200 °C was 480 °C. Phase-separated crystalline phases with spherical shape were observed from the surface of the pellet sintered at a temperature of 550 °C. Crystallization of the pellet was completely occurred at temperatures of 750 and 800 °C. The pellets sintered at temperatures below 700 °C had single crystalline phase of CaNa₃B₅O₁₀. The pellet sintered at a temperature of 800 °C had two crystalline phases of CaNa₃B₅O₁₀ and CaB₂O₄.     

Catalytic filamentous carbon: Structural and textural properties

Catalytic filamentous carbon (CFC) synthesized by the decomposition of methane over iron subgroup metal catalysts (Ni, Co, Fe or their alloys) is a new family of mesoporous carbon materials possessing the unique structural and textural properties. Microstructural properties of CFC (arrangement of the graphite planes in filaments) are shown to depend on the nature of catalyst for methane decomposition. These properties widely vary for different catalysts: the angle between graphite planes and the filament axis can be 0° (Fe-Co-Al₂O₃), 15° (Co-Al₂O₃), 45° (Ni-Al₂O₃), 90° (Ni-Cu-Al₂O₃). The textural properties of CFC depend both on the catalyst nature and the conditions of methane decomposition (T, °C). The micropore volume in CFC is very low, 0.001-0.022 cm³ g⁻¹ at the total pore volume of 0.26-0.59 cm³ g⁻¹. Nevertheless, the BET surface area may reach 318 m² g⁻¹. Results of the TEM (HRTEM), XRD, Raman spectroscopic, SEM and adsorption studies of the structural and textural properties of CFC are discussed.     

Conversions of Methane to Synthesis Gas over Co/γ-Al2O3 by CO2 and/or O2

The goal of the paper was to investigate the effect of the catalyst precursor on the catalytic activity. For this reason, the structure, the reducibility and the reaction behavior of -Al₂O₃-supported Co (24 wt%) catalysts as a function of calcination temperature (T _c) were investigated using X-ray diffraction, temperature-programmed reduction, CO chemisorption, pulse reaction with pure CH₄, and the catalytic reactions of methane conversion to synthesis gas. Depending on T _c, one, two, or three of the following Co-containing compounds, Co₃O₄, Co₂AlO₄, and CoAl₂O₄, were identified. Their reducibility decreased in the sequence: Co₃O₄>Co₂AlO₄>CoAl₂O₄. Co₃O₄ was generated as a major phase at a T _c of 500°C and Co₂AlO₄ and CoAl₂O₄ at a T _c of 1000°C. The reduced Co/-Al₂O₃ catalysts, obtained via the reduction of the 500 and 1000°C calcined catalysts, provided high and stable activities for the partial oxidation of methane and the combined partial oxidation and CO₂ reforming of methane. They deactivated, however, rapidly in the CO₂ reforming of methane. Possible explanations for the stability are provided.     

Carbon Deposition and Catalytic Deactivation during CO2 Reforming of CH4 over Co/γ-Al2O3 Catalysts

The reaction behavior and carbon deposition during the CO₂/CH₄ reforming reaction have been investigated over the γ-Al₂O₃-supported Co catalysts as a function of Co loading (between 2 and 20 wt%) and calcination temperature (T_c=500 or 1000°C). It was found that the stability of Co/γ-Al₂O₃ catalysts was strongly dependent on the Co loading and calcination temperature. For some loadings (6 wt% for T_c=500°C and 9 wt% for T_c=1000°C), stable activities have been achieved. However, over the catalysts with high Co loadings (>12 wt%), notable amounts of carbon were accumulated during reforming, and deactivation was observed. Moreover, severe deactivation was also noted over the 2 wt% catalysts, both when carbon deposition occurred (T_c=500°C) or was absent (T_c=1000°C). In the latter case, the oxidation of the metallic sites was responsible for the deactivation. Hence, there are two different deactivation mechanisms, namely, carbon deposition and oxidation of metallic sites. The activities were stable when a balance between carbon formation and its oxidation could be achieved.     

The phase structure and electric properties of low-temperature sintered (K,Na)NbO3-based piezoceramics modified by CuO

0.25 wt% CuO-doped (Li,K,Na)(Nb,Ta)O₃–AgSbO₃ lead-free piezoceramics with pure perovskite structure were successfully prepared at a sintering temperature below 1000 °C. The sintering temperature of KNN-based piezoceramics was effectively reduced by about 100 °C due to the enhanced densification process induced by the addition of CuO. Besides, the acceptable sintering temperature window was broadened by the addition of CuO. It is found that the CuO-doped samples show slightly higher tetragonal–orthorhombic phase transition point (T_T−O) but a lower Curie point (T_c), compared to undoped ones. The KNN-based piezoceramics became “hard” as CuO was added, supported by an increase of Q_m. Fairly good electrical properties of d₃₃^*=383 pm/V, ε_r=860, Q_m=188 and T_c=215 °C could be obtained in dense CuO-modified KNN-based piezoceramics sintered at 970 °C, demonstrating promising potential in practical applications.     

On the spinel formation in Co1 − xO/Co2TiO4 composites via reactive sintering, exsolution and oxidation

The formation mechanism and microstructural development of the spinel phases in the Co_1 − xO/Co₂TiO₄ composites upon reactive sintering the Co_1 − xO and TiO₂ powders (9:1 molar ratio) at 1450 °C and during subsequent cooling in air were studied by X-ray diffraction and analytical electron microscopy. The Co₂TiO₄ spinel occurred as inter- and intragranular particles in the matrix of Ti-doped Co_1 − xO grains with a rock salt-type structure during reactive sintering. The submicron sized Co₂TiO₄ particles were able to detach from grain boundaries in order to reach an energetically favorable parallel orientation with respect to the host Co_1 − xO grains via a Brownian-type rotation/coalescence process. Upon cooling in air, secondary Co₂TiO₄ nanoparticles were precipitated and the Ti-doped Co_1 − xO host was partially oxidized as Co_3 − δO₄ spinel by rapid diffusion along the {1 1 1} and {1 0 0}-decorated interphase interface and the free surface of the composites.     

One-step synthesis and improved electrochemical performance of Li(Ni1/3Co1/3Mn1/3)O2 by a modified radiated polymer gel method

We present the mechanism for the synthesis of a layered Li(Ni_1/3Co_1/3Mn_1/3)O₂ compound by a modified radiated gel method. Pure-phase Li(Ni_1/3Co_1/3Mn_1/3)O₂ material was achieved when the polymer gel was calcined at 900 °C between 15 and 30 h. The unit cell parameter c decreased, and a varied slightly with increased sintering time. Electrochemical characterization revealed that the optimized sample (25 h) had a high initial discharge capacity of 188 mAh/g (2.8-4.5 V, 20 mA/g), an excellent capacity retention of 90.1% after 30 cycles and a good rate performance.     

Thermal, spectroscopy, and morphological studies on polymorphic crystals in poly(heptamethylene terephthalate)

Polymorphism and its influential factors in poly(heptamethylene terephthalate) (PHepT) were probed using differential scanning calorimetry (DSC), Fourier-transform infrared (FTIR) spectroscopy, and wide angle X-ray diffraction (WAXD). PHepT exhibits two crystal types (α and β) upon crystallization at various isothermal melt-crystallization temperatures (T_cs) by quenching from different T_maxs (maximum temperature above T_m for melting the original crystals). Melt-crystallized PHepT with either initial α- or β-crystal by quenching from T_max lower than 110 °C leads to higher fractions of α-crystal, but crystallization from T_max higher than 140 °C leads to higher fractions of β-crystal. In addition to T_max, polymorphism in PHepT is also influenced by crystallization temperature (T_c = 25-75 °C). When PHepT is melt-crystallized from a high T_max = 150 °C (completely isotropic melt), it shows solely β crystal for higher T_c, and solely the α-crystal for T_c < 25 °C; in-between T_c = 25 and 35 °C, mixed fractions of both α- and β-crystals. However, by contrast, when PHepT is melt-crystallized from a lower T_max = 110 °C, it shows α-crystal only at all T_cs, high or low.     

Development of blue ceramic dyes from cobalt phosphates

In this study the development of blue ceramic dyes from compositions based on phosphate structures have been investigated. The replacement of cobalt by copper or iron to minimize the Co content have been considered. MFeO(PO₄) (M = Co, Cu) solid solutions have been obtained with Co_1−xCu_xFeOPO₄ (0 ≤ x ≤ 1) compositions prepared from gels and fired at 1000 °C/2 h. Co_1−xCu_xFeOPO₄ compositions are not indicated to minimize the Co content in ceramic dyes because they decompose in glazed samples and pinhole defect is obtained. From FeCoOPO₄–2FePO₄ compositions, Co₃Fe₄(PO₄)₆ structure introduces the Co²⁺ ions into glassy matrix and suitable blue materials are obtained. In the conditions of this study, optimal cobalt amount is about 10 wt% Co from Co_1−xFe_1+xO_1−x(PO₄)_1+x (x ≈ 0.6) compositions.     

High permeability Ni-Cu-Zn ferrites through additive-free low-temperature sintering of nanocrystalline powders

Nanocrystalline Ni-Cu-Zn ferrite powders Ni_0.20Cu_0.20Zn_0.62Fe_1.98O_3.99 were prepared by thermal decomposition of an oxalate precursor. The particle size is 6 nm and 350 nm, respectively, for powders obtained through calcinations at 350 °C or 750 °C. The shrinkage behavior significantly changes with particle size; the temperature of maximum shrinkage rate is T_MSR = 700 °C for particles of 6 nm size and increases to T_MSR = 880 °C for particles 350 nm in size. Dense samples with a permeability of μ = 780 are obtained by sintering at 900 °C for 2 h. Mixtures of nanocrystalline and sub-micron powders allow tailoring of the shrinkage behavior. A maximum permeability of μ = 840 is obtained after sintering of a 1:1-mixture at 900 °C. This demonstrates the potential of nanocrystalline ferrites for co-firing without additives at 900 °C and integration of ferrite inductors into LTCC modules.     

Effect of carbon nanotubes on sintering behavior of alumina prepared by sol–gel method

Alumina (Al2O3)/carbon nanotube (CNT) (99/1 by weight) composite was prepared by mixing CNT dispersion with AlCl₃-based gel, followed by high temperature sintering at a temperature up to 1150 °C in argon. Composite alumina precursor showed phase transition order from amorphous to γ-Al₂O₃ after sintered at 900 °C for 2 h, partially to θ-Al₂O₃ after sintered at 1000 °C for 2 h, and then partially to α-Al₂O₃ after sintered at 1150 °C for 2 h. By comparison, control alumina precursor directly transformed from amorphous to α-Al₂O₃ after sintered at a relatively low temperature of 600 °C for 2 h. Composite alumina showed porous structure with pore diameter ranging from 100 nm to 2 µm, whereas control alumina was relatively pore-free. The elevated alumina-crystal phase transition temperatures and the formation of porous structure were ascribed to the presence of CNTs in alumina precursor. The composite alumina sintered at 900 °C for 2 h containing only γ-Al₂O₃ had a BET surface area of 138 m²/g, which was significantly higher than that of control alumina sintered at 1150 °C for 2 h containing only α-Al₂O₃, ~15 m²/g.     

Role of interface on electrical conductivity of carbon nanotube/alumina nanocomposite

Interface of multiwalled carbon nanotube (MWCNT)/alumina (Al₂O₃) nanocomposites have been studied using TEM. At low sintering temperature (T_sin=1500 °C), a 3–5 nm thick amorphous interface region was noticed. Nanocomposite sintered at 1700 °C possessed a well-defined graphene layer coating on matrix grains as the interface between CNT and Al₂O₃. A mechanism of such layered interface formation has been proposed. No traceable chemical reaction product was observed at the interface even after sintering at 1700 °C. It was noticed that while DC electrical conductivity (σ_DC) of 1500 °C sintered 2.4 vol% MWCNT/Al₂O₃ nanocomposite was only~0.02 S/m, it raised to ~21 S/m when sintering was done at 1700 °C. Such 10³ times increase in σ_DC of present nanocomposite at a constant CNT loading was not only resulted from the exceptionally high electron mobility of CNT but the well-crystallized graphene interface on insulating type Al₂O₃ grains also significantly contributed in the overall increase of electrical performance of the nanocomposite, especially, when sintering was done at 1700 °C.     

SrCo0.8Fe0.2O3−δ sorbent for high-temperature production of oxygen-enriched carbon dioxide stream

Perovskite-type SrCo_0.8Fe_0.2O_3−δ (SCF) has been prepared by a liquid citrate method and used to produce O₂-CO₂ gas mixture for oxyfuel combustion. Oxygen is desorbed and an oxygen-enriched carbon dioxide stream is obtained when SCF is exposed in a carbon dioxide stream at high temperature. Oxygen is adsorbed when SCF is regenerated in an air stream. A carbonation-reaction mechanism for O₂-desorption has been identified with the evidences of XRD and TGA analysis. It is found that the theoretical oxygen sorption capacity decreases with the increase of temperature. The sorption kinetics over a temperature range of 700-900 °C has been examined by TGA experiment. Both desorption and sorption processes exhibit a high reaction rate in an initial stage followed by a slower rate in a second stage. It is difficult to reach the theoretical oxygen sorption capacity during the whole temperature range due to the slow oxygen desorption rate. Optimal temperatures for oxygen sorption and desorption processes are determined to be 900 and 850 °C, respectively. Multiple sorption and desorption cycles indicate that SCF sorbent has high reactivity and cyclic stability. Comparison with the reference La_0.1Sr_0.9Co_0.5Fe_0.5O_2.6 (LSCF) and Sr_0.5Ca_0.5Co_0.5Fe_0.5O_2.47 (SCCF) sorbents shows that SCF has faster carbonation reaction at high temperature, i.e., 850 and 900 °C, and much higher theoretical oxygen sorption capacities.     

Effects of PbO and SrO contents on crystallization and dielectric properties of PbO–SrO–Na2O–Nb2O5–SiO2 glass–ceramics system

PbO–SrO–Na₂O–Nb₂O₅–SiO₂ glass–ceramics were prepared via roll-quenching followed by controlled crystallization from 700 °C to 900 °C. The effects of PbO and SrO contents on crystallization and dielectric properties were investigated. The results show that Pb₂Nb₂O₇, Sr₂Nb₂O₇ and their solid solutions crystallize at 700 °C, NaNbO₃ is the primary phase at 800 °C, Pb₂Nb₂O₇ disappears and PbNb₂O₆ forms at 900 °C. The dielectric properties of the glass–ceramics formed through controlled crystallization has a strong dependence on the phase compositions that were developed during heat treatment. The highest dielectric constants (∼600) are found in samples with 6.0 mol% SrO annealed at 900 °C for 3 h. The dielectric–temperature characteristics of the samples show stability over the range from −60 °C to 180 °C, except the sample without SrO heated at 900 °C.     

Electroreduction of oxygen on Co-based catalysts: determination of the parameters affecting the two-electron transfer reaction in an acid medium

Co-based catalysts for the oxygen reduction reaction (ORR) in an acid medium have been prepared from cobalt acetate (CoAc) adsorbed on nine different carbons (previously enriched in surface nitrogen or not). The catalysts were obtained by heat-treating these materials at 900 °C in a reducing environment rich in NH₃. In this work, the emphasis was mainly placed on the electrochemical production of H₂O₂ as measured by the rotating ring-disk electrode (RRDE) technique. It is shown that all Co-based catalysts are active for ORR. The activity and specificity of the catalysts for peroxide production depend essentially on three factors: (i) the potential applied to the disk, (ii) the type of carbon support; and (iii) the concentration of the cobalt precursor. At identical Co loadings (2000 ppm), the percentage of peroxide produced at the disk (%H₂O₂) reaches a maximum in the 0.3-0.1 V versus SCE potential range and decreases for more negative potentials. When the potential is set at a constant value (100 mV versus SCE for instance), a strong effect of the carbon support on %H₂O₂ and on the ring current I_R is noticed, with lower values of %H₂O₂ and I_R corresponding to higher nitrogen content at the surface of the catalysts, while higher values of disk current I_D are obtained under the same conditions. A figure of merit for the electroreduction of oxygen to hydrogen peroxide was obtained for each catalyst by multiplying I_D (representing their activity for ORR) by %H₂O₂ (representing their specificity for H₂O₂ production). According to this figure of merit, the best catalysts for peroxide production are made with Ketjenblack, Black Pearls, Vulcan, and Norit carbon supports. For Co loadings higher than 2000 ppm, it is shown that increasing the loading by more than one order of magnitude (from 2000 to 50,000 ppm) has practically no effect on %H₂O₂ and I_R, while I_D decreases.     

AFM study of crystallization and melting of a poly(ethylene oxide) diblock copolymer containing a tablet-like block of poly{2,5-bis[(4-methoxyphenyl)oxycarbonyl]styrene} in ultrathin films

Crystallization and melting of a poly(ethylene oxide) (PEO) diblock copolymer containing a tablet-like block of poly{2,5-bis[(4-methoxyphenyl)oxycarbonyl]styrene} (PMPCS) in ultrathin films have been studied using atomic force microscopy (AFM) coupled with a hot stage. The PEO and PMPCS block possess the number-average molecular weights (M_n) of 5300 and 2100 g/mol, respectively. The ultrathin films on the mica and glow-discharged carbon surfaces were obtained by static dilute solution casting at room temperature. Isothermal melt crystallization from ultrathin films always leads to flat-on lamellae. Selective area electron diffraction (SAED) experiments have demonstrated that the PEO blocks crystallize with a monoclinic structure identical to that of homo-PEO and the chain direction is perpendicular to the substrate. At T_c<44 °C, the monolayer crystals are dendrites. At T_c>48 °C, square-shaped crystals are formed with the (100) and (020) planes as the crystal edges. At 44 °C≤T_c≤48 °C, an intermediate monolayer morphology is observed. The monolayer thickness increases monotonically with increasing T_c. At the same T_c, the monolayer lamellae with the top and bottom amorphous layers contacting with the atmosphere and the substrate possess a significantly larger overall thickness than the long period of the crystals in bulk. For the spiral terraces induced by screw dislocation, the thickness of each terrace is close to that of the monolayer formed at the same T_c, and their melting is mainly determined by the terrace thickness.     

Formation of LiNi0.5Co0.5VO4 nano-crystals by solvothermal reaction

LiNi_0.5Co_0.5VO₄ nano-crystals were solvothermally prepared using a mixture of LiOH·H₂O, Ni(NO₃)₂·6H₂O, Co(NO₃)₂·6H₂O and NH₄VO₃ in isopropanol at 150–200 °C followed by 300–600 °C calcination to form powders. TGA curves of the solvothermal products show weight losses due to evaporation and decomposition processes. The purified products seem to form at 500 °C and above. The products analyzed by XRD, selected area electron diffraction (SAED), energy dispersive X-ray (EDX) and atomic absorption spectrophotometer (AAS) correspond to LiNi_0.5Co_0.5VO₄. V–O stretching vibrations of VO₄ tetrahedrons analyzed using FTIR and Raman spectrometer are in the range of 620–900 cm⁻¹. A solvothermal reaction at 150 °C for 10 h followed by calcination at 600 °C for 6 h yields crystals with lattice parameter of 0.8252 ± 0.0008 nm. Transmission electron microscope (TEM) images clearly show that the solvothermal temperatures play a more important role in the size formation than the reaction times.