Surfactant-free microwave hydrothermal synthesis of SnO2 nanosheets as an anode material for lithium battery applications

SnO₂ nanosheets were synthesized using microwave hydrothermal method without using a surfactant and organic solvents. Formation of pure nanocrystalline rutile phase of SnO₂ sample was confirmed by X-ray diffraction (XRD) results and the average crystallite size of SnO₂ sample calculated using Scherrer's formula and XRD data is found to be 6 nm. HR-TEM, SAED and EDX results showed the formation of agglomerated nanosize sheets like morphology with high porous structured SnO₂ powder. Further, the formation of high porous structured SnO₂ powder was confirmed from BET surface area results (59.28 m² g^?1). The electrochemical performance of the lithium-ion battery made up of SnO₂ nanosheets, as an anode, was tested through the cyclic voltammetry and galvanostatic charge-discharge measurements. The galvanostatic charge-discharge results of the lithium-ion battery showed good discharge capacity of 257.8 mAh g^?1 after 50 cycles at a current density of 100 mA g^?1. The improved electrochemical properties may be due to the formation of a unique nanosize sheets type morphology with high porous structured SnO₂ powder. High porous structured nanosize sheets type morphology of SnO₂ can help to reduce the diffusion length and sustain the volume changes during the charging-discharging process.Hence, high porous structured nanosize sheets morphology of SnO₂ prepared using the microwave hydrothermal method without using a surfactant and organic solvents can be a better anode material for lithium ion battery applications.     

Enhanced gas sensing properties to NO2 of SnO2/rGO nanocomposites synthesized by microwave-assisted gas-liquid interfacial method

The detection of nitrogen dioxide (NO₂) is essential for the environment and human health. Tin dioxide (SnO₂) based sensors have demonstrated capabilities to detect NO₂, while their response, response/recover speed and selectivity are not good enough for their practical applications. To address these issues, the SnO₂ nanoparticles doped with reduced graphene oxides (rGO) have been synthesized by using a facile microwave-assisted gas-liquid interfacial solvothermal method in this work. The NO₂ sensing performances have been greatly enhanced after the doping of rGO due to the improved electronic conductivity and the formation of the p-n junction in the as-synthesized SnO₂/rGO nanocomposites. Moreover, our results demonstrate that the sensors based on the SnO₂/(0.3%)rGO nanocomposites (with an average diameter about 10–15 nm) exhibit the best overall performance with the high response of 247.8 to 10 ppm NO₂, fast response/recovery speed (39 s/15 s) and the excellent selectivity at the working temperature of 200 ℃. Remarkably, the SnO₂/(0.3%)rGO sensors still exhibit a good gas sensing performance to NO₂ even at room temperature.     

Properties of a single SnO2:Zn2SnO4 – Functionalized nanowire based nanosensor

Tin oxide nanowires (SnO₂ NWs) exhibit large potential for applications in sensor and detector technology. Using a flame transport synthesis method, high-quality single crystalline SnO₂ nanowires (NWs) with Zn₂SnO₄ dots functionalized surface were synthesized on a large scale. The individual SnO₂:Zn₂SnO₄ nanowire based ultraviolet photodetector and ethanol vapors nanosensors were fabricated by contacting an individual nanowire to pre-patterned Au electrodes via a FIB/SEM system. The photodetector structure exhibited excellent photoconductive performance in terms of high response to the 375 nm ultraviolet light irradiation, ultra-fast response and recovery time at different temperatures (25–300 K). It also showed a long term stability and reliability. The n-type semiconducting behavior of the SnO₂:Zn₂SnO₄, forms an excellent material for fabricating highly sensitive and rapid responding sensors, which will enable the development of high-performance multi-functional devices.     

Preparation of meso-porous SnO2 fibers with enhanced sensitivity for n-butanol

Meso-porous SnO₂ fibers were synthesized using a solvothermal method with metaplexis fruit as the bio-template. The products were characterized by powder X-ray diffraction, high resolution scanning electron microscopy, transmission electron microscopy and nitrogen adsorption/desorption measurements. Results show that SnO₂ fibers present a high specific surface area of 73.665 m²/g and a meso-porous structure with the pore size of 7.821 nm, and the crystal size of SnO₂ is about 6.5 ± 0.5 nm. The gas sensing performance of the prepared SnO₂ fibers toward several volatile organic compounds was investigated. The results show that the meso-porous SnO₂ fibers were highly sensitive and selective to n-butanol.     

LaFeO3 ceramics as selective oxygen sensors at mild temperature

In this study, an investigation about the oxygen sensing properties of lanthanum orthoferrite (LaFeO₃) ceramics is reported. LaFeO₃ nanoparticles were synthesized by using tartaric sol-gel route and annealed in air at different temperatures (500, 700 and 900 °C). The samples have been characterized by using thermal analysis (TA), BET surface area and porosity, Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, X-ray diffraction (XRD), and scanning electron microscopy (SEM). Results of sensing tests indicate that LaFeO₃ nanoparticles exhibit good response to oxygen at mild temperatures (300–450 °C). The effect of annealing temperature on gas sensing performance was investigated, demonstrating that LaFeO₃ ceramics obtained after annealing at 500 °C display better characteristics with respect to others. The oxygen sensor developed shows also high stability in humid environment and excellent selectivity to oxygen over other interfering gases such as CO, NO₂, CO₂, H₂ and ethanol.     

Improved ethanediol sensing with single Yb ions doped SnO2 nanobelt

Yb-doped SnO₂ nanobelts (Yb–SnO₂ NBs) and pure SnO₂ nanobelts (SnO₂ NBs) are successfully synthesized by thermal evaporation method and their composition and morphology are characterized. The single nanobelt device is fabricated by dual-ion beam deposition system, and the gas sensing performance to ethanediol, methanal, ethanol and acetone is investigated. The results show that the best working temperature of single Yb–SnO₂ NB sensor to ethanediol is 190 °C, which is lower than that of pure counterpart and the highest sensitivity is 10.5 to 100 ppm of ethanediol. In addition, it is found that the response/recovery time is short and the sensor exhibits excellent selectivity and stability. The sensing performance of SnO₂ NB is actually improved by Yb.     

Structural,photocatalytic, biological and catalytic properties of SnO2/TiO2 nanoparticles

TiO₂ and SnO₂/TiO₂ nanoparticles with different SnO₂ contents (0–20 wt%) were synthesized via surfactant-assisted sol-gel method using a cationic surfactant (cetyltrimethylammonium bromide, CTAB). The effects of SnO₂ content on the structural, optical, and catalytic activity of TiO₂ have been studied by X-ray diffraction (XRD), Transmission electron microscope (TEM), Scanning electron microscope (SEM), Fourier transformer infrared (FTIR) and UV–vis diffuse reflection spectroscopy (DRS). The total surface acidity of the prepared samples was measured by nonaqueous titration of n-butylamine in acetonitrile and the types of Brönsted and Lewis acid sites were distinguish using FTIR spectra of chemisorbed pyridine. XRD patterns analysis indicates that the crystallite size reduced remarkably and the transformation of anatase-to-rutile phase accelerated greatly with increasing the SnO₂ content. TEM images exhibit a spherical shape with an average particle size varying in the range 10–24 nm and high-resolution TEM images (HRTEM) show lattice fringes with interplanar spacing 0.35 nm and 0.32 nm which corresponding to anatase and rutile phases, respectively. SEM images show the amount of SnO₂ on the TiO₂ surface increases with increasing the SnO₂ content and the particles of SnO₂ were aggregated on TiO₂ surface with increasing SnO₂ content to 20% wt. The catalytic activity was tested by various applications: Photodegradation of Methylene Blue (MB) and Rhodamine B (RhB) under UV–vis irradiations and synthesis of xanthene (14-phenyl-14H-dibenzo [a,j] xanthene). Antibacterial and antioxidant activities were also studied. The antibacterial property test was carried out via agar disc diffusion method, and the results indicated that the prepared catalysts showed moderate antibacterial activity.     

Nanocomposites of SnO2 and g-C3N4: Preparation,characterization and photocatalysis under visible LED irradiation

Tin dioxide nanoparticles were prepared in the presence of graphitized carbon nitride (g-C₃N₄) forming nanocomposites with different contents of SnO₂ up to 40 %. G-C₃N₄ was synthetized by heating of melamine at 550 °C in the open air and Sn²⁺ ions were precipitated by sodium hydroxide in g-C₃N₄ aqueous dispersions. Resulting mixtures were dried by freezing at ?20 °C and calcined at 450 °C to obtain SnO₂/g-C₃N₄ nanocomposites.The nanocomposites were characterized by common characterization methods in solid state and in their aqueous dispersions using dynamic light scattering (DLS) analysis and photocatalysis. SnO₂ nanoparticles in the nanocomposites were found to have an average size of 4 nm, however, those precipitated without g-C₃N₄ had an average size of 14 nm. Separation of photoinduced electron and holes via heterojunction between SnO₂ and g-C₃N₄ was demonstrated by photocatalytic decomposition of Rhodamine B (RhB) under LED visible irradiation (416 nm) and photocurrent measurements. The most photocatalytically active nanocomposite contained 10 % of SnO₂. Graphitized carbon nitride was assumed to serve as a template structure for the preparation of SnO₂ nanoparticles with a narrow size distribution without using any stabilizing additives.     

In2O3 nanosheets array directly grown on Al2O3 ceramic tube and their gas sensing performance

Arrayed In₂O₃ nanosheets were synthesized directly via a two-step solution approach on an Al₂O₃ ceramic tube. Their morphology and structure were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), UV–Vis absorption spectroscopy, and scanning electron microscopy (SEM). The results reveal that the length of each nanosheet is about 1 µm, the width of the bottom of nanosheet is about 200 nm. Importantly, the In₂O₃ nanosheets with large specific surface area possess highly sensing performance for ethanol detection. The response value to 100 ppm ethanol is about 45 at an operating temperature of 280 °C, and the response and recovery time are extremely short. It is expected that the directly grown In₂O₃ nanosheets with large specific surface area and excellent sensing properties will become a promising functional material in monitoring and detecting ethanol.     

Highly sensitive acetone sensor based on Eu-doped SnO2 electrospun nanofibers

In this study, a series of undoped and Eu-doped SnO₂ nanofibers were synthesized via a simple electrospinning technique and subsequent calcination treatment. Field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were carefully used to characterize the morphologies, structures and chemical compositions of these samples. The results reveal that the as-prepared nanofibers are composed of crystallite grains with an average size of about 10 nm and Eu³⁺ ions are successfully doped into the SnO₂ lattice. Compared with pure SnO₂ nanofibers, Eu-doped SnO₂ nanofibers demonstrate significantly enhanced sensing characteristics (e.g., large response value, short response/recovery time and outstanding selectivity) toward acetone vapor, especially, the optimal sensor based on 2 mol% Eu-doped SnO₂ nanofibers shows the highest response (32.2 for 100 ppm), which is two times higher than that of the pure SnO₂ sensor at an operating temperature of 280 °C. In addition, the sensor exhibits a good sensitivity to acetone in sub-ppm concentrations and the detection limit could extend down to 0.3 ppm, making it a potential candidate for the breath diagnosis of diabetes.     

Annealing impact on the structural and optical properties of electrospun SnO2 nanofibers for TCOs

Tin oxide (SnO₂) nanofibers were fabricated by electrospinning technique and subsequent annealed at different temperatures. The structure, morphology and optical properties of the annealed samples were characterized by X-ray diffraction (XRD), Raman, scanning electron microscopy/energy dispersive spectroscopy (SEM/EDS), transmission electron microscopy (TEM), Fourier transformed infrared (FTIR),and optical absorption techniques. The phase of SnO₂ of all samples is rutile (tetragonal), and at higher annealing temperatures, good crystallinity and lower absorption were obtained. Annealing of the samples at 600 °C caused the lower absorption and higher optical band gap, and the decrease of the absorption was probably because the fiber structure changed from solid to hollow structure. From PL spectra, it was observed that the SnO₂ hollow nanofibers annealed at 600 °C revealed green emission at 530 nm.     

H2 response characteristics for sol–gel-derived WO3-SnO2 dual-layer thin films

This paper describes the deposition of SnO₂ and WO₃ thin films and WO₃-SnO₂ dual-layer thin films using the sol-gel process. The microstructure and morphology of these three thin films were analyzed with FE-SEM and X-ray diffraction. The H₂ response characteristics, including response magnitude, time and transients of the three samples, were investigated at different operation temperatures and H₂ gas concentrations. Although the maximum response magnitude of 29.31 towards 1000 ppm H₂ gas appeared at 225 °C,the WO₃-SnO₂ dual-layer films still had a response magnitude of 24.23 at 175 °C, which is much higher than those of the SnO₂ (4.19) and WO₃ (6.73) thin films. The linear response magnitude profile of the WO₃-SnO₂ dual-layer thin films toward H₂ gas concentration was obtained. The mechanism of the enhanced gas response characteristics was explained by the band bending theory.     

Enhanced gas sensing properties of hierarchical SnO2 nanoflower assembled from nanorods via a one-pot template-free hydrothermal method

Well-defined three-dimensional (3D) hierarchical tin dioxide (SnO₂) nanoflowers with the size of about 200 nm were successfully synthesized by a simple template-free hydrothermal method. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and N₂ adsorption-desorption analyses were used to characterize the structure and morphology of the products. The as-synthesized full crystalline and large specific surface area SnO₂ nanoflowers were assembled by one-dimensional (1D) SnO₂ nanorods with sharp tips. A possible self-assembly mechanism for the formation the SnO₂ nanoflowers was speculated. Moreover, gas sensing investigation showed the sensor based on SnO₂ nanoflowers to exhibit high response and fast response-recovery ability to detect acetone and ethanol at an operating temperature lower than 200 °C. The enhancement of gas sensing properties was attributed to their 3D hierarchical nanostructure, large specific surface area, and small size of the secondary SnO₂ nanorods.     

The control of abnormal grain growth in low-voltage SnO2 varistors by microseed addition

In this research, the addition effects of three different quantities of micron-sized seeds (microseeds) to a SnO₂ varistor prepared from nanomaterials on the microstructure and electrical properties were studied. Moreover, surge-withstanding capability of low-voltage SnO₂ varistors was investigated. The X-ray diffraction pattern disclosed a single phase SnO₂ for microseed grains. The morphological features of samples were characterized using scanning electron microscopy. The abnormal distribution of grain size with elongated grains of SnO₂ in fine grains matrix was observed in sintered samples without microseeds. The low content of microseed addition (0.3 wt%) had not controlled abnormal grain growth, however, it increased mean grain size to 37 µm. Although the high content of microseeds (7.5 wt%) stopped abnormal grain growth, it had a negative effect on relative density and mean grain size. The normal grain size distribution with maximum mean grain size (45 µm) was obtained in samples containing 1.5 wt% microseeds. These samples showed the lowest breakdown field (240 V/cm) and the highest surge-withstanding capability (1.5 kA/cm²). Furthermore, the standard deviation of the electrical parameters of these samples was improved due to normal grain-size distribution.     

Hierarchical heterostructure of porous NiO nanosheets on flower-like ZnO assembled by hexagonal nanorods for high-performance gas sensor

A novel hierarchical heterostructure consisting of porous NiO nanosheets and flower-like ZnO assembled by hexagonal nanorods was successfully fabricated by a simple two-step hydrothermal approach. Flower-like ZnO was obtained by the first step hydrothermal method. Through the second step hydrothermal method, porous NiO nanosheets grew on the surface of flower-like ZnO to realize integration of ZnO and NiO, so the p-n heterostructure between ZnO and NiO formed. The samples were investigated by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and energy dispersive X-ray (EDX). Gas sensing test results showed that the sensor based on NiO/ZnO composite exhibited superior sensing properties to acetone. The sensor response to 100 ppm acetone was about 205.14 at the optimum working temperature of 240 °C, and the response and recovery times were about 7 and 20 s, respectively. The enhanced response might be attributed to heterojunction and larger specific surface area provided by attached porous NiO nanosheets. The rapid response and recovery characteristics and improved selectivity attributed to the porous structure and good catalytic actions of NiO nanosheets.     

Experiments and transient finite element simulation of γ-Y2Si2O7/B2O3-Al2O3-SiO2 glass coating on porous Si3N4 substrate under thermal shock

A dense γ-Y₂Si₂O₇/B₂O₃-Al₂O₃-SiO₂ glass coating was fabricated by slurry spraying method on porous Si₃N₄ ceramic for water resistance. Thermal shock failure was recognized as one of the key failure modes for porous Si₃N₄ radome materials. In this paper, thermal shock resistance of the coated porous Si₃N₄ ceramics were investigated through rapid quenching thermal shock experiments and transient finite element analysis. Thermal shock resistance of the coating was tested at 700 °C, 800 °C, 900 °C and 1000 °C. Results showed that the cracks initiated within the coating after thermal shock from 800 °C to room temperature, thus leading to the reduction of the water resistance. Based on the finite element simulation results, thermal shock failure tended to occur in the coating layer with increasing temperature gradient, and the critical thermal shock failure temperature was measured as 872.24 °C. The results obtained from finite element analysis agree well with that from the thermal shock tests, indicating accuracy and feasibility of this numerical simulation method. Effects of thermo-physical properties for the coating material on its thermal shock resistance were also discussed. Thermal expansion coefficient of the coating material played a more decisive role in decreasing the tangent tensile stress.     

Enhanced NO2 sensing properties of Zn2SnO4-core/ZnO-shell nanorod sensors

Zn₂SnO₄-core/ZnO-shell nanorods were synthesized using a two-step process: synthesis of Zn₂SnO₄ nanorods the thermal evaporation of a mixture of ZnO, SnO₂, and graphite powders, followed by atomic layer deposition (ALD) of ZnO. The nanorods were 50–250 nm in diameter and a few to a few tens of micrometers in length. The cores and shells of the nanorods were face-centered cubic-structured single crystal Zn₂SnO₄ and wurtzite-structured single crystal ZnO, respectively. The multiple networked Zn₂SnO₄-core/ZnO-shell nanorod sensors showed a response of 173–498% to NO₂ concentrations of 1–5 ppm at 300 °C. These response values are 2–5 times higher than those of the Zn₂SnO₄ nanorod sensor over the same NO₂ concentration range. The NO₂ sensing mechanism of the Zn₂SnO₄core/ZnO-shell nanorods is discussed.     

Influence of Pd-loading on gas sensing characteristics of SnO2 thick films

Nanocrystalline pristine and 0.5, 1.5 and 3.0 wt% Pd loaded SnO₂ were synthesized by a facile co-precipitation route. These powders were screen-printed on alumina substrates to form thick films to investigate their gas sensing properties. The crystal structure and morphology of different samples were characterized by using X-ray diffraction, scanning electron microscopy and transmission electron microscopy techniques. The 3.0 wt% Pd:SnO₂ showed response of 85% toward 100 ppm of LPG at operating temperature of 250 °C with fast response (8 s) and quick recovery time (24 s). The high response toward LPG on Pd loading can be attributed to lowering of crystallite size (9 nm) as well as the role of Pd particles in exhibiting spill-over mechanism on the SnO₂ surface. Also selectivity of 3.0 wt% Pd:SnO₂ toward LPG was confirmed by measuring its response to other reducing gases like acetone (CH₃COCH₃), ethanol (C₂H₅OH) and ammonia (NH₃) at optimum operating temperature.     

Synthesis of graphene/α-Fe2O3 nanospindles by hydrothermal assembly and their lithium storage performance

Nanocomposite of graphene/α-Fe₂O₃ (G/α-Fe₂O₃) nanospindles was synthesized by a simple hydrothermal assembly method followed by thermal treatment. The α-Fe₂O₃ nanospindles were evenly enwrapped by the graphene nanosheets. When evaluated as an anode for Li-ion batteries (LIBs), the G/α-Fe₂O₃ nanocomposite showed enhanced cycling performance and rate capability compared to pure α-Fe₂O₃. G/α-Fe₂O₃ retained a reversible capacity of 607 mAh g^?1 after 100 cycles at 100 mA g^?1-, which is far higher than that (160 mAh g^?1) of α-Fe₂O₃. The superior electrochemical performance of G/α-Fe₂O₃ can be attributed to the protection effect of graphene nanosheets to accommodate the volume change of α-Fe₂O₃ during lithiation/delithiation.     

Fabrication and performance of dielectric tape based on CaO-B2O3-SiO2 glass/Al2O3 for LTCC applications

A non-aqueous tape-casting process for fabricating CaO-B₂O₃-SiO₂ glass/Al₂O₃ dielectric tape for LTCC applications was investigated. An isopropanol/ethanol/xylene ternary solvent-based slurry was developed by using castor oil, poly(vinyl butyral), and dibutyl phthalate as dispersant, binder, and plasticizer, respectively. The effects of dispersant concentration, binder content, plasticizer/binder ratio, and solid loading, on the properties of the casting slurry and resultant tape were systematically investigated. The results showed that the optimal values for the dispersant and binder contents, plasticizer/binder ratio, and solid loading were 2.0 wt%, 7.5 wt%, 0.6, and 62 wt%, respectively. The resultant flexible and uniform, 120-μm-thick CaO-B₂O₃-SiO₂ glass/Al₂O₃ tape had a density of 1.90 g/cm^?3, tensile strength of 1.66 MPa, and average surface roughness of 310 nm. Laminated tapes sintered at 875 °C for 15 min exhibited excellent properties: relative density of 97.3%, ε_r of 7.98, tan δ of 1.3 × 10^?3 (10 MHz), flexural strength of 205 MPa, and thermal expansion coefficient of 5.47 ppm/°C. The material demonstrated good chemical compatibility with Ag electrodes, indicating a significant potential in LTCC applications.