熔盐中电解钛铁矿制备TiFe合金

通过在CaCl2熔盐中电解钛铁矿制备TiFe合金,研究了熔盐电解钛铁矿的反应过程,分析了电解产物的成分及电解效率。结果显示,钛铁矿的还原经历了优先生成Fe到逐步形成TiFe2、TiFe的合金化历程,中间产物包括 CaTiO3、Fe2TiO4、TiO。反应最先生成的合金是TiFe2合金,通过Ti和TiFe2的互扩散最终转变成TiFe合金, 说明扩散是反应的控制步骤。相同电解条件下,钛铁矿较混合氧化物难电解。这是由于钛铁矿颗粒较大,其杂质是固溶到钛酸铁中的,脱氧更难,电解效率较低     

金属热还原法制备钛铝中间合金

以TiO_2为原料,KClO_3为发热剂,Al为还原剂和合金化剂,Ca为深度还原剂,通过金属热还原法制备钛铝中间合金,考察了单位质量热效应、造渣剂配比和还原剂加入量及组成对反应过程稳定性、合金成分及收率的关系。研究表明:用Ca和Al作为还原剂时,体系绝热温度分别是2426和1806 K,反应制得的钛铝中间合金由Ti Al、Ti_3Al和少量的Al_2O_3夹杂相组成,化学分析合金中Ti、Al、O质量分数分别为58.36%、40.19%和1.41%。     

Effect of Ilmenite Component and AIR on Element Distribution of Titanium Slag Smelted by DC Arc Furnace

助化学平衡计算法,对冶炼过程中钛、碳及伴生元素的分配行为进行了研究,并用生产结果加以验证,计算结果与实验结果较吻合。结果表明:钛铁矿中Ti O2和Fe O含量的增加,增加了作为微量元素和用于还原Fe O和Ti O2的C量,提高了钛渣中总的Ti O2和Ti2O3的量,同时降低了用于还原Fe2O3的C量,降低了钛渣中Fe O的含量。当钛渣中Fe2O3含量由12%增加到20%时,作为微量元素C和用于还原Fe2O3的C量分别降低了0.006 mol和0.348 mol,钛渣中总的Ti O2和Ti2O3的量分别降低了8.34%和2.37%,而用于还原Fe2O3的C量增加了约0.36 mol,Fe O的质量分数增加了8.94%。其他成分对钛渣中总的Ti O2量的影响程度由大到小排序为:Si O2>Mg O>Al2O3>Ca O。对钛渣还原冶炼过程中元素分配行为的研究,可实现对工艺的更好控制、提高钛渣品位。     

熔盐电解制备低成本Ti12LC钛合金的研究

采用熔盐电解法由混合氧化物成功制备出了低成本Ti12LC合金,并对脱氧过程机理进行分析。结果显示:脱氧反应过程首先生成CaTiO3、低价氧化物Ti6O、Ti2O和Ca2Al2O5;其次随脱氧时间的进行钛的低价氧化物含量逐步增加,再其次出现金属钼,最后生成Ti12LC合金相。由于MoO2的理论电压低于TiO2、Al2O3,因此钼优先还原,且钼在-Ti中能固溶,所以最终钼是以固溶体形式存在于钛中,而Fe2O3虽然理论分解电位更低,但由于含量低,而没有检测到铁的单质还原。通过对电解产物表面的背散射电子像分析,发现电解制备出的产物其形貌和Ti12LC合金的组织相似。     

熔盐电解法制备铝-钪合金电解质体系电化学性质研究

熔盐体系的电化学性质对熔盐电解过程有很大影响,通过选用铝电解工业通用的冰晶石-氧化铝体系作为熔盐电解制取铝钪合金的基本电解质体系,采用循环伏安法、线性伏安法和稳态极化法对Sc3+在冰晶石熔盐体系中铝电极上的电化学还原过程及氧化钪在石墨电极上的分解电压进行研究.结果表明,Sc3+在熔盐中电解还原过程为一步获得三个电子的简单电荷传递过程.     

Al-Mg-Sc中间合金的制备

在非真空条件下用氟化物熔盐体系镁 (铝 )热还原法制备了Al Mg Sc中间合金 ,讨论了金属还原剂的选择及还原温度、时间等工艺条件对钪收率的影响 ,并研究制定了氧化钪固相氟化制备氟化钪熔盐工艺。采用Al Mg合金熔体为还原剂经二次还原后钪收率 >80 %,制备的Al Mg Sc中间合金铸锭中钪含量 >1.9%,最佳的还原反应温度为 110 0K ,还原时间 40min .。氟化钪还原产生的初生态钪与铝作用形成稳定的Al3 Sc化合物 ,促进了还原的进行 ,使钪收率得到了大幅度提高。     

金属热还原法制备V-Ti-Fe中间合金(英文)

采用金属热还原热法制备V-Ti-Fe中间合金,考察V2O5与TiO2的加入比例、用铝量和Al-Mg合金用量对金属回收率和合金成分的影响。结果表明:最佳工艺参数为原料中V2O5和TiO2的质量比为0.5:1,实际用铝量为理论值的95%,Al-Mg合金用量为铝量的1/3。能谱分析结果表明,合金中的V和Fe元素分布比较均匀,Ti则存在一定偏析。为降低合金中Al和O的杂质含量,进行喷吹造渣精炼。精炼后,合金中的铝含量由4.27%降为1.86%,氧含量由2.10%降为0.91%。     

铝热还原法制备Al-Ti中间合金

在温度为1150～1300℃的冰晶石熔体中,以TiO2为原料、Al为还原剂,制得了含Ti为7.83%～11.80%(质量百分数)的Al-Ti中间合金。讨论了温度、Al2O3加入量及搅拌等参数对Al-Ti合金中Ti含量的影响。研究发现,在石墨坩埚内还原的Al-Ti中间合金,Ti主要以TiAl3和TiC的形式存在;冰晶石熔体中TiO2的添加量相对于金属Al过剩时,会产生爬壁现象。     

铝热还原制备高钛铁的热力学和动力学

对金红石、钛铁矿、铝粉体系热力学进行了计算.结果表明:以Al、Ca、Mg、Ba、Li、Na等金属做还原剂是可行的,标态下反应的吉布斯自由能变化都很负,可以选用这些金属的合金作为复合还原剂.DSC动力学分析结果表明:Al还原TiO2、Fe2O3在1 000 ℃左右开始进行,而Al还原TiO2、Fe2O体系中添加CaO,反应滞后,在1 236 ℃左右发生反应.     

Al-Ti合金的相组成以及硅对合金组织的影响

前言本研究用金相法及X射线衍射研究了Al-Ti合金的相组成,以及硅对Al-Ti合金组织的影响. Al-2～4%Ti合金,由Al-Ti平衡图可知,其组织为A1 Al_3Ti.在以铝热还原二氧化钛制取Al-Ti合金的情况下,二氧化钛是否充分还原而形成金属化合物Al_3 Ti,本研究作了一些探讨. 在工业纯铝中,杂质硅的含量为0.13～1.0%(特一号铝——三号铝,GB1196-75).因此,用工业纯铝炼制的Al-Ti合金,杂质硅是不可避免的.Al-Ti合金中存在的杂质硅,其分布形态以及对组织的影响是冶金工     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

THERMODYNAMICS STUDY ON THE DECOMPOSITION OF CHROMITE WITH KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

INFLUENCE OF HEAT TREATMENT ON DAMPING BEHAVIOUR OF THE MAGNESIUM WROUGHT ALLOY AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.