Visual study of flow patterns during condensation inside a microfin tube with different tube inclinations

In this paper, flow patterns and their transitions for refrigerant R-134a condensing in a microfin tube are visually observed and analyzed. The microfin tube has been provided with different tube inclination angles of the direction of fluid flow from horizontal, α. The experiments were performed for seven different tube inclinations, α, in a range of − 90° to + 90° and refrigerant mass velocities in a range of 53 to 212 kg/m²s for each tube inclination angle during condensation of R-134a vapor. From analysis of acquired data, it was found that the tube inclination strongly influenced the vapor and condensate liquid distribution. Annular flow was the dominant flow pattern for vertical downward flow, α = − 90°. Annular flow, semi annular flow and stratified flow were observed for α = − 60°and − 30°. Annular flow, wavy-annular flow and stratified-wavy flow exist in sequence for horizontal tube. Annular flow and wavy-annular flow were observed for α = + 30°and + 60°. Annular flow, annular-wavy flow, churn flow and slug flow occurred for α = + 90°.     

Unsteady steam condensation flow patterns inside a miniature tube

Unsteady steam condensation inside a single miniature tube has been studied. The visualization of different instantaneous and periodically two-phase flow is conducted for different experimental conditions. The two-phase flow characterization is obtained using the image processing. Annular, slug bubbly, spherical bubbly, and wavy flows are observed by varying the steam inlet pressure and cooling heat transfer. The cycle of the periodically flows are compared. It is shown that increasing the cooling heat flow rate reduces the number of the instabilities and the injected bubbles. The axial vapor velocity decreases during the waves growth. The local distribution of the condensate film thickness is analyzed. It is shown that the liquid film becomes thinner near the meniscus-like interface because of the surface tension effect. The reverse annular flow is observed at the end of each periodic flow when the bubbles leave the channel. It can be concluded from experimental results that the stratification effect is not significant during the condensation inside the miniature tube. The capillary pressure evolution is measured. The maximum values are obtained in the waves locations and near the meniscus of the annular flow.     

Flow pattern of boiling in micro-channel by numerical simulation

Boiling flows of R-134a and R-22 fluids in a 0.50 mm circular channel have been simulated to analyze bubbly flow, bubbly/slug flow, slug flow and slug/semi-annular flow depending on bubble evolution. The vapor–liquid interface was captured using VOF method. We studied the behavior of bubble growth and coalescence related to flow pattern transitions (bubbly/slug flow to slug flow, slug flow to slug/semi-annular flow) and analyzed the effect of fluid properties on transition lines. Some parameters, including heat flux, mass velocity, ONB point, vapor velocity, bubble lifting diameter, growth rate and generation frequency, have been analyzed in detail. The results show that bubble growth and coalescence are important factors for flow pattern transitions. The flow patterns at the micro-channel outlet predicted by simulation were in agreement with phenomena observed in experiments for bubbly/slug flow, slug flow and slug/semi-annular flow. In addition, the peak bubble frequency at the outlet was predicted and the general shape of the bubble frequency distribution at the outlet from simulation was found to be consistent with the achieved experimental results.     

Experiment of flow regime map and local condensing heat transfer coefficients inside three dimensional inner microfin tubes

INTRODUCTIONSince1980s,thestudyofthein-tubecondensingheattransferenhancementhasbecomeimportant.Thetwodimensionalinnerfintubes,twodimensionalinnermicrofintubes(inthefollowingsimplycalled2Dtubes)andinserterswerepaidattentiontoforthein-tubecondensinghea...     

Experimental study of condensation heat transfer of R-134a flow in corrugated tubes with different inclinations

This experimental study is performed to investigate condensation heat transfer coefficient of R-134a flow inside corrugated tube with different inclinations. Different inclinations of test condenser ranging from − 90^° to + 90^° and various flow mass velocities in the range of 87 to 253 [kg/m²s] are considered in this study. Data analysis showed that change in the tube inclination had a significant effect on condensation heat transfer behavior. At low mass velocities, and low vapor qualities, the highest condensation heat transfer coefficient was obtained for α = + 30^° which was 1.41 times greater than the least one obtained for α = − 90^°. The results also showed that at all mass velocities, the highest average heat transfer coefficients were achieved for α = + 30^°. Based on the experimental results, a new empirical correlation is proposed to predict the condensation heat transfer coefficient of R134a flow in corrugated tubes with different inclinations.     

An experimental study of flow pattern and pressure drop for flow boiling inside microfinned helically coiled tube

In this paper, flow patterns and their transitions for refrigerant R134a boiling in a microfinned helically coiled tube are experimentally observed and analyzed. All the flow patterns occurred in the test can be divided into three dominant regimes, i.e., stratified-wavy flow, intermittent flow and annular flow. Experimental data are plotted in two kinds of flow maps, i.e., Taitel and Dukler flow map and mass flux versus vapor quality flow map. The transitions between various flow regimes and the differences from that in smooth straight tube have also been discussed. Martinelli parameter can be used to indicate the transition from intermittent flow to annular flow. The transition from stratified-wavy flow to annular or intermittent flow is identified in the vapor quality versus mass flux flow map. The flow regime is always in stratified-wavy flow for a mass flux less than 100 kg/m² s.The two-phase frictional pressure drop characteristics in the test tube are also experimentally studied. The two-phase frictional multiplier data can be well correlated by Lockhart–Martinelli parameter. Considering the corresponding flow regimes, i.e., stratified and annular flow, two frictional pressure drop correlations are proposed, and show a good agreement with the respective experimental data.     

The effect of tube diameter on vertical two-phase flow regimes in small tubes

Flow boiling flow patterns in four circular tubes with internal diameters of 1.10, 2.01, 2.88 and 4.26 mm were investigated in the present project. The experiments were conducted in vertical upward two-phase flow using R134a as the working fluid. The observed flow patterns include dispersed bubble, bubbly, confined bubble, slug, churn, annular and mist flow. The flow characteristics in the 2.88 and 4.26 mm tubes are similar to those typically described in normal size tubes. The smaller diameter tubes, 1.10 and 2.01 mm, exhibit strong “small tube characteristics” as described in earlier studies. The sketched flow maps show that the transition boundaries of slug-churn and churn-annular depend strongly on diameter. On the contrary, the dispersed bubble to churn and bubbly to slug boundaries are less affected. The transition boundaries are compared with existing models for normal size tubes showing poor agreement.     

Two-phase flow pattern in small diameter tubes with the presence of horizontal return bend

This study provides a qualitatively visual observation of the two-phase flow patterns for air-water mixtures inside 6.9, 4.95, and 3 mm smooth diameter tubes with the presence of horizontal return bend. The influence of the return bend on the two-phase flow patterns are investigated. For D=6.9 mm and at a mass flux of 50 kg m⁻² s⁻¹ having a quality less than 0.1, no influence on the flow patterns is seen at a larger curvature ratio of 7.1. However, were the curvature ratio reduced to 3, the flow pattern in the recovery region is temporarily turned from stratified flow into annular flow. The temporary flow pattern transition phenomenon from stratified flow to annular flow is not so pronounced with the decrease of tube diameter. It is likely that this phenomenon is related to the influence of surface tension and the reduction of developing length of the swirl flow. Based on the present flow visualization, three flow pattern maps are proposed to describe the effect of return bend on the transition of two-phase flow pattern.     

Condensation heat transfer of R-134a inside a microfin tube with different tube inclinations

Experimental heat transfer studies during condensation of pure R-134a vapor inside a single microfin tube have been carried out. The microfin tube has been provided with different tube inclination angles of the direction of fluid flow from horizontal, α. The data are acquired for seven different tube inclinations, α, in a range of −90 to +90° and three mass velocities of 54, 81, and 107 kg/m²-s for each inclination angle during condensation of R-134a vapor. The experimental results indicate that the tube inclination angle of, α, affects the condensation heat transfer coefficient in a significant manner. The highest heat transfer coefficient is attained at inclination angle of α = +30°. The effect of inclination angle, α, on heat transfer coefficient, h, is more prominent at low vapor quality and mass velocity. A correlation has also been developed to predict the condensing side heat transfer coefficient for different vapor qualities and mass velocities.     

Transition from annular flow to plug/slug flow in condensation of steam in microchannels

A visualization study has been conducted to investigate the transition from annular flow to plug/slug flow in the condensation of steam in two different sets of parallel microchannels, having hydraulic diameters of 90 μm and 136 μm, respectively. The steam in the parallel microchannels was cooled on the bottom by forced convection of water and by natural convection of air from the top. It is found that the location, where the transition from annular flow to plug/slug flow takes place, depends on mass flux and cooling rate of steam. The effects of mass flux and cooling rate on the occurrence frequency of the injection flow in a single microchannel, having a hydraulic diameter of 120 μm and 128 μm, respectively, are investigated. It is found that two different shapes of injection flow occur in the smooth annular flow in microchannels: injection flow with unsteady vapor ligament occurring at low mass flux (or high cooling rate) and injection flow with steady vapor ligament occurring at high mass flux (or low cooling rate). It is also found that increase of steam mass flux, decrease of cooling rate, or decrease of the microchannel diameter tends to enhance instability of the condensate film on the wall, resulting in occurrence of the injection flow further toward the outlet with an increase in occurrence frequency.     

Experimental study for the stratified to slug flow regime transition mechanism of gas-oil two-phase flow in horizontal pipe

Theoretical relations that predict the transition from a stratified pattern to a slug pattern, including a onedimensional wave model that contains less empiricism than the commonly used Taitel-Dukler model, and the ideal model for stratified flow for the gas-liquid flow in horizontal pipes are presented. Superficial velocities of each phase, as the onset of slugging occurs, were predicted, and theoretical analysis was conducted on the stratified to slug flow regime transition. The friction, existing between the fluid and pipe wall, and on the interface of two phases, was especially taken into account. A theoretical model was applied to an experiment about air-oil two-phase flow in a 50 mm horizontal pipe. The effect of pipe diameter on the transition was also studied. The results show that this approach gives a reasonable prediction over the whole range of flow rates, and better agreement has been achieved between predicted and measured critical parameters. __________ Translated from Journal of Shanghai Jiaotong University, 2006, 40(10): 1782–1785, 1789 [译自: 上海交通大学学报]     

Heat transfer and flow characteristics of flow boiling of CO2‐oil mixtures in horizontal smooth and micro‐fin tubes

Experiments were carried out on the flow pattern, heat transfer, and pressure drop of flow boiling of pure CO₂ and CO₂‐oil mixtures in horizontal smooth and micro‐fin tubes. The smooth tube is a stainless steel tube with an inner diameter of 3.76 mm. The micro‐fin tube is a copper tube with a mean inner diameter of 3.75 mm. The experiments were carried out at mass velocities from 100 to 500 kg/(m²·s), saturation temperature of 10 °C, and the circulation ratio of lubricating oil (PAG) was from 0 to 1.0 mass%. Flow pattern observations mainly showed slug and wavy flow for the smooth tube, but annular flow for the micro‐fin tube. Compared with the flow patterns in the case of pure CO₂, an increase in frequency of slug occurrence in the slug flow region, and a decrease in the quantity of liquid at the top of the tube in the annular flow region were observed in the case of CO₂‐oil mixtures. With pure CO₂, the flow boiling heat transfer was dominated by nucleate boiling in the low vapor quality region, and the heat transfer coefficients for the micro‐fin tube were higher than those of the smooth tube. With CO₂‐oil mixtures, the flow boiling heat transfer was dominated by convective evaporation, especially in the high vapor quality region. In addition, the heat transfer coefficient decreased significantly when the oil circulation ratio was larger than 0.1 mass%. For the pressure drop characteristics, in the case of pure CO₂, the homogeneous flow model agreed with the experimental results within ±30% for the smooth tube. The pressure drops of the micro‐fin tube were 0–70% higher than those predicted with the homogeneous flow model, and the pressure drops increased for the high oil circulation ratio and high vapor quality conditions. The increases in the pressure drops were considered to be due to the increase in the thickness of the oil film and the decrease in the effective flow cross‐sectional area. © 2010 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20287     

Condensation flow patterns in silicon microchannels

A simultaneous visualization and measurement experiment was carried out to investigate condensation flow patterns of steam flowing through an array of trapezoidal silicon microchannels, having a hydraulic diameter of 82.8 μm and a length of 30 mm. The degassed and deionized water steam flowing in the microchannels was cooled by flowing water of 8 °C from the bottom. The silicon microchannels were covered with a thin transparent pyrex glass from the top which enabled the visualization of flow patterns. Experiments were performed at different inlet pressures ranging from 4.15 × 10⁵ Pa to 1.25 × 10⁵ Pa (with corresponding mass fluxes decreasing from 47.5 g/cm² s to 19.3 g/cm² s) while the outlet pressure was maintained at a value of 10⁵ Pa. Different condensation flow patterns such as fully droplet flow, droplet/annular/injection/slug-bubbly flow, annular/injection/slug-bubbly flow, and fully slug-bubbly flow were observed in the microchannels. At a given inlet pressure and mass flux, the flow pattern depended on both the location and time. Of particular interest is that the vapor injection flow, consisting of a series of bubble growth and detachment activities, appeared and disappeared periodically. During the disappearance period of injection flow, the slug-bubbly flow at downstream changed to the single-phase liquid flow due to the reversed flow of outlet condensate, while the annular flow at upstream changed to the vapor flow due to the effect of incoming vapor. Therefore, two-phase flow and single-phase flow appeared alternatively in the microchannels, causing large fluctuations of wall temperatures as well as other measurements. It was also found that the occurrence of vapor injection flow moved from the outlet toward the inlet as the mass flux was decreased. The vapor injection flow and its induced condensation instabilities in microchannels are reported here for the first time.     

Two-phase co-current flow in inclined pipe

Data are presented on horizontal and slightly inclined flows at +5 and −5° for a 0.058 m inner diameter (i.d.) pipe with the co-current air–water system.The prediction capabilities of existing flow regime maps were shown to be inadequate. However, the transitions for stratified ripple to role wave, for slug to blow-through-slug, for film plus droplet to stratified, and the modified maps for stratified type to slug flows all gave good prediction performance with horizontal and slightly inclined flows.The largest liquid hold-up occurred in upward flow except at high gas rates and low liquid rates where the downflow condition gave the highest liquid hold-up. The lowest liquid hold-up occurred in downward flow at low gas flow rates and horizontal flow at high gas flow rates. Hold-up prediction proved to be flow regime dependent.The inclined total average pressure drop data crossed over the horizontal data from higher to lower values with increasing gas rate at a gas rate of just under V?_SG = 10 m s⁻¹.Below this gas rate the horizontal pipe gave the lowest pressure drop while above this gas rate the upwardly inclined pipe gave the lowest pressure drop. A pressure loss minimum occurred at V?_SG = 10 m s⁻¹ for upward flows. Below V?_SG = 10 m s⁻¹ the pressure loss for downward flow was virtually independent of gas rate being mainly due to hydrostatic head. As the gas flow approached V?_SG = 50 m s⁻¹ there was very little effect of inclination on the pressure loss.Pressure drop was successfully predicted although the accompanying hold-up prediction was not always reliable.     

一种基于差压波动图的段塞流识别方法

在内径为80mm的大型水平实验环道上进行了广泛的空气一水两相流实验,将采集的一定时间长度的分层、段塞、环状流型的差压波动信号,显示成二维图像。通过对30组差压波动数据分析发现：段塞流的信号区和背景区面积之比平均为0．026,分层流为0,53,环状流为0．35。段基流信号区占整个图像面积的比值远小于其他流型,因此该比值可以作为判别段塞流型的一个特征参数。该方法能有效利用于段塞流流型的快速自动检测。     

Experimental analysis of the unit cell approach for two-phase flow dynamics in curved flow channels

Flow behavior of gas–liquid mixtures in thin channels has become increasingly important as a result of miniaturization of fluid and thermal systems. The present empirical study investigates the use of the unit cell or periodic boundary approach commonly used in two-phase flows. This work examines the flow patterns formed in small tube diameter (<3 mm) and curved geometry flow systems for air–water mixtures at standard conditions. Liquid and gas superficial velocities were varied from 0.1 to 7.0 (～±0.01) m/s and 0.03 to 14 (～±0.2) m/s for air and water respectively to determine the flow pattern formed in three geometries and dispersed bubble, plug, slug and annular flow patterns are reported using high-frame rate videography. Flow patterns formed were plotted on the generalized two-phase flow pattern map to interpret the effect of channel size and curvature on the flow regime boundaries. Relative to a straight a channel, it is shown that a ‘C shaped’ channel that causes a directional change in the flow induces chaotic advection and increases phase interaction to enhance gas bubble or liquid slug break-up thus altering the boundaries between the dispersed bubble and plug/slug flow regimes as well as between the annular and plug/slug flow regimes.     

Improved flow pattern map for accurate prediction of the heat transfer coefficients during condensation of R-134a in smooth horizontal tubes and within the low-mass flux range

This paper presents an improved flow pattern map for predicting the heat transfer coefficients during condensation of R-134a inside a smooth horizontal tube. Experimental tests were conducted over the low-mass flux range of 75–300 kg/m² s, at a nominal saturation temperature of 40 °C, and with the test section vapour qualities ranging from 0.76 down to 0.03. This represents points within the annular, intermittent and stratified flow regimes. The results were used to modify the Thome–El Hajal flow pattern map to include a transition region between the stratified-wavy and annular or intermittent flow regimes. The revised flow pattern-based heat transfer correlation predicted the experimental data to a mean deviation of less than 6%.     

Study on Characteristics of Steady Flow Condensation Heat Transfer in a Fube Under Zero—Gravitation

ＳｔｕｄｙｏｎＣｈａｒａｃｔｅｒｉｓｔｉｃｓｏｆＳｔｅａｄｙＦｌｏｗＣｏｎｄｅｎｓａｔｉｏｎＨｅａｔＴｒａｎｓｆｅｒｉｎａＴｕｂｅｕｎｄｅｒＺｅｒｏ－ＧｒａｖｉｔａｔｉｏｎＱｎＷｅｉ（ＨａｒｂｉｎＩｎｓｔｉｔｕｔｅｏｆＴｅｃｈｎｏｌｏｇｙ，Ｈａｒｂｉ...     

Experimental study for the stratified to slug flow regime transition mechanism of gas-oil two-phase flow in horizontal pipe

Theoretical relations that predict the transition from a stratified pattern to a slug pattern, including a one-dimensional wave model that contains less empiricism than the commonly used Taitel-Dukler model, and the ideal model for stratified flow for the gas-liquid flow in horizontal pipes are presented. Superficial velocities of each phase, as the onset of slugging occurs, were predicted, and theoretical analysis was conducted on the stratified to slug flow regime transition. The friction, existing between the fluid and pipe wall, and on the interface of two phases, was especially taken into account. A theoretical model was applied to an experiment about air-oil two-phase flow in a 50 mm horizontal pipe. The effect of pipe diameter on the transition was also studied. The results show that this approach gives a reasonable prediction over the whole range of flow rates, and better agreement has been achieved between predicted and measured critical parameters.     

Mapping of horizontal refrigerant two-phase flow patterns based on clustering of capacitive sensor signals

A capacitive void fraction sensor was developed to study the objectivity in flow pattern mapping of horizontal refrigerant two-phase flow in macroscale tubes. Sensor signals were gathered with R410A and R134a in a smooth tube with an inner diameter of 8 mm at a saturation temperature of 15 °C in the mass velocity range of 200–500 kg/m² s and vapour quality range from 0 to 1 in steps of 0.025. A visual classification based on high speed camera images is made for comparison reasons. A statistical analysis of the sensor signals shows that the average, the variance and a high frequency contribution parameter are suitable for flow regime classification into slug flow, intermittent flow and annular flow by using the fuzzy c-means clustering algorithm. This soft-clustering algorithm predicts the slug/intermittent flow transition very well compared to our visual observations. The intermittent/annular flow transition is found at slightly higher vapour qualities for R410A compared to the prediction of Barbieri et al. (2008) [20]. An excellent agreement was obtained with R134a. This intermittent/annular flow transition is very gradual. A probability approach can therefore better describe such a transition. The membership grades of the cluster algorithm can be interpreted as flow regime probabilities. Probabilistic flow pattern maps are presented for R410A and R134a in an 8 mm ID tube.