A Voltage Scalable 0.26 V, 64 kb 8T SRAM With V$_{min}$ Lowering Techniques and Deep Sleep Mode

A voltage scalable 0.26 V, 64 kb 8T SRAM with 512 cells per bitline is implemented in a 130 nm CMOS process. Utilization of the reverse short channel effect in a SRAM cell design improves cell write margin and read performance without the aid of peripheral circuits. A marginal bitline leakage compensation (MBLC) scheme compensates for the bitline leakage current which becomes comparable to a read current at subthreshold supply voltages. The MBLC allows us to lower ${rm V}_{min}$ to 0.26 V and also eliminates the need for precharged read bitlines. A floating read bitline and write bitline scheme reduces the leakage power consumption. A deep sleep mode minimizes the standby leakage power consumption without compromising the hold mode cell stability. Finally, an automatic wordline pulse width control circuit tracks PVT variations and shuts off the bitline leakage current upon completion of a read operation.      

1-V 100-MHz embedded SRAM techniques for battery-operatedMTCMOS/SIMOX ASICs

Multithreshold-voltage CMOS (MTCMOS) has a great advantage of lowering physical threshold voltages without increasing the power dissipation due to large subthreshold leakage currents. This paper presents the embedded SRAM techniques for high-speed low-power MTCMOS/SIMOX application-specified integrated circuits (ASICs) that are operated with a single battery cell of around 1 V. In order to increase SRAM operating frequency, a pseudo-two stage pipeline architecture is proposed. The address decoder using a pass-transistor-type NAND gate and a segmented power switch presents a short clocked wordline selection time. The large bitline delay in read operations is greatly shortened with a new memory cell using extra low-V_th nMOSs. The small readout signal from memory cells is detected with a high-speed MTCMOS sense amplifier, in which a pMOS bitline selector is merged. The wasted power dissipation in writing data is reduced to zero with a self-timed writing action. A 8 K-words×16-bits SRAM test chip, fabricated with a 0.35-μm MTCMOS/SIMOX process (shortened effective channel length of 0.17 μm is available), has demonstrated a 100-MHz operation under the worst power-supply condition of 1 V. At a typical 1.2 V, the power dissipation during the standby time is 0.2-μW and that of a 100-MHz operation with a checkerboard test pattern is 14 mW for single fan-in loads     

A bitline leakage compensation scheme for low-voltage SRAMs

A bitline leakage current of an SRAM, induced by leakage current of the transmission transistors in the cells that are associated with the bitline, increases as the threshold voltage (V_TH) of the transistors is reduced for high performance at low power-supply voltage (V_DD). The increased bitline leakage causes slow or incorrect read/write operation of an SRAM because the leakage current acts as noise current for a sense amplifier. In this paper, the problem has been solved from a circuitry point of view, and the scheme which detects the bitline leakage current in a precharge cycle and compensates for it during a read/write cycle is proposed. Employing this scheme, the SRAM with 360-μA bitline leakage current can perform a read/write operation at the same speed as one that has no bitline leakage current. This enables a 0.1-V reduction in V_TH, and keeps the V_TH and delay scalability of a high-performance SRAM in technology progress. An experimental 8-Kb SRAM with 256 rows is fabricated in a 0.25-μm CMOS technology, which demonstrates the effectiveness of the scheme     

Design and analysis of a 32 nm PVT tolerant CMOS SRAM cell for low leakage and high stability

A novel nine transistor (9T) CMOS SRAM cell design at 32 nm feature size is presented to improve the stability, power dissipation, and delay of the conventional SRAM cell along with detailed comparisons with other designs. An optimal transistor sizing is established for the proposed 9T SRAM cell by considering stability, energy consumption, and write-ability. As a complementary hardware solution at array-level, a novel write bitline balancing technique is proposed to reduce the leakage current. By optimizing its size and employing the proposed write circuit technique, 33% power dissipation saving is achieved in memory array operation compared with the conventional 6T SRAM based design. A new metric that comprehensively captures all of these figures of merit (and denoted to as SPR) is also proposed; under this metric, the proposed 9T SRAM cell is shown to be superior to all other cell configurations found in the technical literatures. The impact of the process variations on the cell design is investigated in detail. HSPICE simulation shows that the 9T SRAM cell demonstrates an excellent tolerance to process variations comparing with the conventional SRAM cells.     

A low leakage SRAM macro with replica cell biasing scheme

For mobile applications of SRAMs, there is a need to reduce standby current leakages while keeping memory cell data. For this purpose, we propose a replica cell biasing scheme which controls the cell bias voltage by self-tuning using replica cells. This scheme minimizes the cell leakage regardless of the process fluctuations and the environmental conditions. In addition, leakage reduction in row decoder circuits is also desirable, because standby current leakages in peripheral circuits are dominated by row decoders. We also propose a row decoder circuit which can reduce both the off-leakage and the gate-leakage in the row decoders. We fabricated a 90-nm 512-Kb low-leakage SRAM macro to verify the proposed leakage reduction techniques. With these techniques, 88% reduction of the standby leakage in the sleep mode and 40% reduction of the leakage compared with the conventional diode clamp scheme are realized.     

A 6-GHz 16-kB L1 cache in a 100-nm dual-V/sub T/ technology using a bitline leakage reduction (BLR) technique

This work describes an aggressive SRAM cell configuration using dual-V/sub T/ and minimum channel length to achieve high performance. A bitline leakage reduction technique is incorporated into an L1 cache design using the new cell in a 100-nm dual-V/sub T/ technology to eliminate impacts of bitline leakage on performance and noise margin with minimal area overhead. Bitline delay is 23% better than the best conventional design, thus enabling 6-GHz operation at with 15% higher energy.     

Circuit techniques for a 1.8-V-only NAND flash memory

Focusing on internal high-voltage (V_pp) switching and generation for low-voltage NAND flash memories, this paper describes a V _(pp) switch, row decoder, and charge-pump circuit. The proposed nMOS V_pp switch is composed of only intrinsic high-voltage transistors without channel implantation, which realizes both reduction of the minimum operating voltage and elimination of the V _pp leakage current. The proposed row decoder scheme is described in which all blocks are in selected state in standby so as to prevent standby current from flowing through the proposed V_pp switches in the row decoder. A merged charge-pump scheme generates a plurality of voltage levels with an individually optimized efficiency, which reduces circuit area in comparison with the conventional scheme that requires a separate charge-pump circuit for each voltage level. The proposed circuits were implemented on an experimental NAND flash memory. The charge pump and V_pp switch successfully operated at a supply voltage of 1.8 V with a standby current of 10 μA. The proposed pump scheme reduced the area required for charge-pump circuits by 40%     

A channel-erasing 1.8-V-only 32-Mb NOR flash EEPROM with a bitlinedirect sensing scheme

A 1.8-V-only 32-Mb NOR flash EEPROM has been developed based on the 0.25-μm triple-well double-metal CMOS process. A channel-erasing scheme has been implemented to realize a cell size of 0.49 μm² , the smallest yet reported for 0.25-μm CMOS technology. A block decoder circuit with a novel erase-reset sequence has been designed for the channel-erasing operation. A bitline direct sensing scheme and a wordline boosted voltage pooling method have been developed to obtain high-speed reading operation at low voltage. An access time of 90 ns at 1.8 V has been realized     

用于SRAM的低功耗位线结构

提出了一种用于SRAM的低功耗位线结构,通过两种途径来实现低位线电压.在写操作时,利用单边驱动结构来抑制位线上充电电压的过大摆动;在读写操作时,改进预充结构来使位线电压保持较低.仿真表明,该结构使功耗大大节省.     

A replica technique for wordline and sense control in low-powerSRAM's

With the migration toward low supply voltages in low-power SRAM designs, threshold and supply voltage fluctuations will begin to have larger impacts on the speed and power specifications of SRAM's. We present techniques based on replica circuits which minimize the effect of operating conditions' variability on the speed and power. Replica memory cells and bitlines are used to create a reference signal whose delay tracks that of the bitlines. This signal is used to generate the sense clock with minimal slack time and control wordline pulsewidths to limit bitline swings. We implemented the circuits for two variants of the technique, one using bitline capacitance ratioing in a 1.2-μm 8-kbyte SRAM, and the other using cell current ratioing in a 0.35-μm 2-kbyte SRAM. Both the RAM's were measured to operate over a wide range of supply voltages, with the latter dissipating 3.6 mW at 150 MHz at 1 V and 5.2 μW at 980 kHz at 0.4 V     

A 90-nm CMOS 1.8-V 2-Gb NAND flash memory for mass storage applications

A 1.8-V 2-Gb NAND flash memory has been successfully developed on a 90-nm CMOS STI process technology, resulting in a 141-mm/sup 2/ die size and a 0.044-/spl mu/m/sup 2/ effective cell. For the higher level integration, critical layers are patterned with KrF photolithography. The device has three notable differences from previous generations. 1) The cells are organized in a single (16K+512) column and 128K row array by adopting a one-sided row decoder in order to minimize the die size. 2) The bitline precharge level is set to 0.9 V in order to increase on-cell current. 3) During the program operations, the string select line, which connects the NAND cell strings to the bitlines, is biased with sub-V/sub CC/ in order to avoid program disturbance issues.     

Measurement of transient effects in SOI DRAM/SRAM accesstransistors

Bitline-induced transient effects in access transistors pose a problem in SOI DRAM and SRAM cells. The floating-body potential is affected by the bitline so changes in the bitline potential may upset the charge stored in the memory cell. Transient effects in SOI access transistors are measured versus the time the bitline is at high voltage, and V_DD for fully- and partially-depleted SOI devices. Bulk devices show no bitline-induced transient effects. Measurements show that the magnitude of the charge upset can be large enough to disturb the charge stored in DRAM and SRAM cells. Measurements also show that for any substantial upsets to occur, the time the bitline has to be at high voltage is on the order of milliseconds. Although the effect of bitline transitions is cumulative, the amount of charge upset when the bitline switches rapidly (i.e., millisecond periods) is shown to be negligible. Thus, proper design of SRAM upset-charge protection and DRAM refresh time should circumvent this problem     

90% write power-saving SRAM using sense-amplifying memory cell

This paper describes a low-power write scheme which reduces SRAM power by 90% by using seven-transistor sense-amplifying memory cells. By reducing the bitline swing to V/sub DD//6 and amplifying the voltage swing by a sense-amplifier structure in a memory cell, the charging and discharging component of the power of the bit/data lines is reduced. A 64-kb test chip has been fabricated and correct read/write operation has been verified. It is also shown that the scheme can also have the capability of leakage power reduction with small modifications. Achievable leakage power reduction is estimated to be two orders of magnitude from SPICE simulation results.     

A 4.0 GHz 291 Mb Voltage-Scalable SRAM Design in a 32 nm High-k + Metal-Gate CMOS Technology With Integrated Power Management

This paper introduces a high-performance voltage-scalable SRAM design in a 32 nm strain-enhanced high-k + metal-gate logic CMOS technology. The 291 Mb SRAM design features a 0.171 ?m² six-transistor bitcell that supports a broad range of operating voltages for low-power and high-frequency embedded applications. The tileable 128 kb SRAM subarray achieves 72% array efficiency with 4.2 Mb/mm² bit density, and consumes 5 mW of leakage power at the supply voltage of 1 V. The design provides 4 GHz and 2 GHz of operating frequencies at the supply voltages of 1.0 V and 0.8 V, respectively. The integrated power management scheme features close-loop memory array leakage control, floating bitline, and wordline driver sleep transistor, resulting in a 58% reduction in subarray leakage power consumption.     

A 16-Mb 400-MHz loadless CMOS four-transistor SRAM macro

We have used a 5-metal 0.18-μm CMOS logic process to develop a 16-Mb 400-MHz loadless CMOS four-transistor SRAM macro. The macro contains: (1) end-point dual-pulse drivers for accurate timing control; (2) a wordline-voltage-level compensation circuit for stable data retention; and (3) an all-adjoining twisted bitline scheme for reduced bitline coupling capacitance. The macro is capable of 400-MHz high-speed access at 1.8-V supply voltage and is 66% the size of a conventional six-transistor SRAM macro. We have also developed a higher-performance 500-MHz loadless four-transistor SRAM macro in a CMOS process using 0.13-μm gate length     

A current-based reference-generation scheme for 1T-1C ferroelectric random-access memories

A reference generation scheme is proposed for a 1T-1C ferroelectric random-access memory (FeRAM) architecture that balances fatigue evenly between memory cells and reference cells. This is achieved by including a reference cell per row (instead of per column) of the memory array. The proposed scheme converts the bitline voltage to current and compares this current against a reference current using a current-steering sense amplifier. This scheme is evaluated over a range of bitline lengths and cell sizes in a 16-Kb test chip implemented in a 0.35-/spl mu/m FeRAM process. The test chip measures an access time of 62 ns at room temperature using a 3-V power supply.     

一种基于位交错结构的亚阈值10管SRAM单元

提出了一种基于位交错结构的亚阈值10管SRAM单元,实现了电路在超低电压下能稳定地工作,并降低了电路功耗。采用内在读辅助技术消除了读干扰问题,有效提高了低压下的读稳定性。采用削弱单元反馈环路的写辅助技术,极大提高了写能力。该10管SRAM单元可消除半选干扰问题,提高位交错结构的抗软错误能力。在40 nm CMOS工艺下对电路进行了仿真。结果表明,该10管SRAM单元在低压下具有较高的读稳定性和优异的写能力。在0.4 V工作电压下,该10管SRAM单元的写裕度为传统6管单元的14.55倍。     

A 0.5-V 25-MHz 1-mW 256-kb MTCMOS/SOI SRAM for solar-power-operated portable personal digital equipment - sure write operation by using step-down negatively overdriven bitline scheme

Multithreshold-voltage CMOS (MTCMOS) technology has a great advantage in that it provides high-speed operation with low supply voltages of less than 1 V. A logic gate with low-V/sub th/ MOSFETs has a high operating speed, while a low-leakage power switch with a high-V/sub th/ MOSFET eliminates the off-leakage current during sleep time. By using MTCMOS circuits and silicon-on-insulator (SOI) devices, the authors have developed a 256-kb SRAM for solar-power-operated digital equipment. A double-threshold-voltage MOSFET (DTMOS) is adopted for the power switch to further reduce the off leakage. As regards the SRAM core design, we consider a hybrid configuration consisting of high-V/sub th/ and low-V/sub th/ MOSFETs (that is, multi-V/sub th/ CMOS). A new memory cell with a separate read-data path provides a larger readout current without degrading the static noise margin. A negatively overdriven bitline scheme guarantees sure write operation at ultralow supply voltages close to 0.5 V. In addition, a charge-transfer amplifier integrated with a selector and data latches for intrabus circuitry are installed to enhance the operating speed and/or reduce power dissipation. A 32K-word /spl times/ 8-bit SRAM chip, fabricated with the 0.35-/spl mu/m multi-V/sub th/ CMOS/SOI process, has successfully operated at 25 MHz under typical conditions with 0.5-V (SRAM core) and 1-V (I/O buffers) power supplies. The power dissipation during sleep time is less than 0.4 /spl mu/W and that for 25-MHz operation is 1 mW, excluding that of the I/O buffers.     

An ultrahigh-density high-speed loadless four-transistor SRAM macrowith twisted bitline architecture and triple-well shield

We have developed two schemes for improving access speed and reliability of a loadless four-transistor (LL4T) SRAM cell: a dual-layered twisted bitline scheme, which reduces coupling capacitance between adjacent bitlines in order to achieve highspeed READ/WRITE operations, and a triple-well shield, which protects the memory cell from substrate noise and alpha particles. We incorporated these schemes in a high-performance 0.18-μm-generation CMOS technology and fabricated a 16-Mb SRAM macro with a 2.18-μm² memory cell. The macro size of the LL4T-SRAM is 56 mm², which is 30% to 40% smaller than a conventional six-transistor SRAM when compared with the same access speed. The developed macro functions at 500 MHz and has an access time of 2.0 ns. The standby current has been reduced to 25 μA/Mb with a low-leakage nMOSFET in the memory cell     

A 550-ps access 900-MHz 1-Mb ECL-CMOS SRAM

An ultrahigh-speed 1-Mb emitter-coupled logic (ECL)-CMOS SRAM with 550-ps clock-access time, 900-MHz operating frequency, and 12-μm² memory cells has been developed using 0.2-μm BiCMOS technology. Three key techniques for achieving the ultrahigh speed are a BiCMOS word decoder/driver with an nMOS level-shift circuit, a sense amplifier with a voltage-clamp circuit, and a BiCMOS write circuit with a variable-impedance bitline load. The proposed word decoder/driver and sense amplifier can reduce the delay times of the circuits to 54% and 53% of those of conventional circuits. The BiCMOS write circuit can reduce the power dissipation of the circuit by 74% without sacrificing writing speed. These techniques are especially useful for realizing ultrahigh-spaced high-density SRAMs, which will be used as cache and control memories in mainframe computers