6061铝合金无倾角搅拌摩擦焊工艺及性能

目的 为了适应空间曲面构件的搅拌摩擦焊,开展6061铝合金无倾角搅拌摩擦焊工艺及性能的研究。方法 采用无倾角搅拌摩擦焊用的搅拌头,对5 mm厚6061-T6铝合金板材进行试验,研究焊缝成形及接头力学性能,并分析接头组织特征。结果 零倾角搅拌摩擦焊接头从组织上可区分为5个不同区域：焊核区(WNZ)、热力影响区(TMAZ)、热影响区(HAZ)、轴肩影响区(SAZ)和母材(BM);随着搅拌头转速增加,焊缝宽度和焊核尺寸均先变大后变小;随焊接速度增加,焊缝宽度和焊核尺寸均逐渐变小;当焊接速度固定时,随搅拌头转速增加,接头拉伸强度先增加后减小;当搅拌头转速固定时,随焊接速度增加,接头拉伸强度逐渐增大。结论 采用无倾角搅拌摩擦焊接方法,能够实现对5 mm厚6061-T6铝合金板材的有效焊接。     

工艺参数对Al-Mg异种金属搅拌摩擦焊-钎焊复合焊接接头力学性能的影响

目的研究工艺参数对Al-Mg异种金属搅拌摩擦焊-钎焊复合焊接接头力学性能的影响。方法采用搅拌摩擦焊-钎焊方法,在不同焊接工艺参数下焊接2A12-T4铝合金和AZ31镁合金。结果当焊接速度为23.5mm/min、旋转速度为375 r/min时,焊接接头的抗拉剪力达到最大,为5.5 kN,比搅拌摩擦焊接头的最大抗拉剪力的5.0 kN提高了10%。结论搅拌摩擦焊-钎焊复合焊接的工艺参数会显著影响铝/镁异种金属接头力学性能,通过优化工艺参数能够获得力学性能优异的铝/镁异种金属焊接接头。复合焊接接头的抗拉剪力随着焊接速度的增大呈现先增大后减小的趋势。     

铝/钢搅拌摩擦焊对接焊缝组织及机理研究

为了提高Q235钢板和6082-T6铝合金对接的连接强度,采用搅拌摩擦焊进行对接焊接.研究了不同尺寸和形状的搅拌头、转速、焊接速度和偏移量等对铝钢对接焊缝组织的影响,进而优化了搅拌摩擦焊工艺.实验结果表明:不同形状的搅拌头影响接头"钉子"形状,接头的不同位置处由于受到不同热循环和搅拌导致晶粒尺寸不同,从而影响接头的力学性能.当搅拌针旋转速度260 r/min,焊接速度16 mm/min,针头偏向铝侧0.2 mm时,所得焊缝的拉伸强度为141.204 MPa,为最佳工艺参数.在此最优参数下获得过渡层的厚度约为8μm,界面的主要成分是Fe Al3.     

不同基体组织对搅拌摩擦焊接接头性能的影响

对板厚为5mm的2024,6082,7050-T7451三种铝合金进行搅拌摩擦焊接实验.结果表明:搅拌摩擦焊接铝合金2024时,接头部位很容易出现孔洞缺陷,但一定尺寸范围内的缺陷并未严重削弱接头的抗拉强度.铝合金6082可在很大的范围内选择工艺参数,接头成型性明显好于铝合金2024和7050-T7451,工艺参数的改变对接头的抗拉强度无大的改变.铝合金7050-T7451在设计的焊接参数范围内没有发现孔洞缺陷,但接头的抗拉强度系数比铝合金2024和6082接头都低.因为搅拌摩擦焊接接头的性能除与焊接工艺参数有关外,基体材料的屈服强度、延展性、基体硬度等也是不可忽视的影响因素.     

水下搅拌摩擦焊对铝/铜接头组织与性能的影响

目的 采用搅拌摩擦焊,对比分析大气环境和水下环境下铝/铜接头的组织与性能,以期获得力学性能更优异的铝/铜焊接接头。方法 利用搅拌摩擦焊,在焊接速度为40 mm/min、旋转速度为1 000 r/min的条件下,分别在大气环境和水下环境下对厚度为9 mm的6061铝合金板和T2纯铜板进行焊接。然后,对铝/铜界面、焊核区进行扫描电镜及能谱分析,并对铝/铜界面及焊核区进行物相分析,确定产物相组成。最后,对铝/铜试样进行拉伸及硬度检测。结果 铝/铜接头均无裂纹、气孔等缺陷。铜颗粒弥散分布在焊核区,铝/铜界面形成金属间化合物层。水下搅拌摩擦焊下界面元素扩散距离明显变短,且金属间化合物厚度更薄。铝/铜接头的金属间化合物为AlCu和Al4Cu9。大气环境焊接下接头的抗拉强度为130.6 MPa,断裂方式为脆性断裂;水下焊接下接头的抗拉强度为199.5 MPa,断裂方式为韧性断裂。水下环境下的接头硬度值更高,其中热影响区的硬度最低值约为65HV。结论 水下搅拌摩擦焊铝/铜接头无裂纹、气孔等缺陷。组织上,水下搅拌摩擦焊的铝/铜接头界面元素扩散距离更短,硬脆的金属间化合物更少;性能上,水下搅拌摩擦焊的铝/铜接头强度更高,抗拉强度达到199.5 MPa,达到母材的74.4%。     

2A12铝合金筋板件T型搅拌摩擦焊工艺及焊后热处理

为评价2A12铝合金筋板件搅拌摩擦焊工艺并探寻提高接头强度的途径,进行了2A12铝合金筋板件的T型搅拌摩擦焊焊接工艺试验,并对不同人工时效热处理下焊接接头的微观组织及性能进行了研究.研究表明:采用T型搅拌摩擦焊即可实现2A12铝合金筋板件的成形,当搅拌头旋转速度为750 r/min、焊接速度60mm/min时,接头的抗...     

5083铝合金搅拌摩擦焊接头的显微组织与力学性能

对8 mm厚5083-H321铝合金板进行了搅拌摩擦焊接试验,研究了焊接工艺参数对搅拌摩擦焊接头显微组织和力学性能的影响。结果表明:该搅拌摩擦焊接头焊核区显微组织为细小的等轴晶组织,热机影响区为拉伸弯曲变形组织,热影响区非常窄,其晶粒尺寸与母材相当;综合接头表面形貌和拉伸性能得到较佳的搅拌摩擦焊接工艺参数为使用搅拌针为三棱形带螺纹、轴肩为内扣型的搅拌头,主轴转速为300 r·min^-1,焊接速率为120 mm·min^-1;在该工艺条件下接头表面成形良好,抗拉强度可达到母材的94.5%。     

超声冲击对铝合金搅拌摩擦焊接头组织及性能的影响

目的分析超声冲击对铝合金搅拌摩擦焊成形后接头的组织及耐蚀性的作用效果。方法采用超声冲击设备对2A12铝合金搅拌摩擦焊接头表面进行超声冲击处理,并对超声冲击前后接头的显微组织、显微硬度以及耐腐蚀性能进行了分析。结果经过超声冲击处理后的铝合金接头上表面会产生一层塑性变形层,并且塑性层内位错密度增大,使表层金属得到一定程度的加工硬化,促使冲击后接头各区域的表面硬度明显提高,冲击后接头热机械影响区和热影响区硬度提高达60%以上;腐蚀浸泡试验发现,超声冲击后接头的点腐蚀程度较超声冲击前明显减缓,腐蚀速率约是冲击前的1/2。结论超声冲击有效改善了铝合金搅拌摩擦焊接头区域材料过时效的软化现象,并且有效改善了接头的抗腐蚀性能。     

2219和2195铝合金焊接接头的腐蚀行为差异研究

目的 研究运载火箭贮箱用2195新型铝锂合金搅拌摩擦焊接头和熔化焊接头相对于传统的2219铝合金焊接接头耐腐蚀性能的差异,分析耐蚀性的演变规律,为贮箱制造及表面防护提供理论指导。方法 以传统的2219铝合金为对照,采用盐雾腐蚀试验、动电位极化曲线测试等方法系统研究2195铝锂合金焊接接头的腐蚀电位、腐蚀电流密度、腐蚀速率等方面的性能,进而判断新型铝合金材料与传统铝合金材料耐蚀性能的差异。结果 2种铝合金焊接接头各个亚区的耐蚀性均呈现相同的变化规律,其中搅拌摩擦焊接头的耐蚀性能按照热影响区、母材区、热机影响区、焊核区的顺序依次增加;TIG焊接头的耐蚀性能按照热影响区、母材区、焊缝区的顺序依次增加,且在热影响区存在晶间腐蚀的现象。此外,2219和2195铝合金TIG焊接接头热影响区自腐蚀电位分别为?0.653 V和?0.667 V,腐蚀电流密度分别为7.35 mA/cm²和7.55 mA/cm²。结论 2219和2195铝合金搅拌摩擦焊和TIG焊接头的耐蚀性差别不大,且均在热影响区耐蚀性最差;采用同种合金进行焊接时,TIG焊接头的耐蚀性能比FSW接头的差。     

焊接速度对 7A52 铝合金 FSW 组织及力学性能的影响

目的在保证搅拌速度一定时,针对8 mm厚的7A52铝合金,在不同焊接速度下采用搅拌摩擦焊(FSW)进行焊接试验,研究其焊接接头的显微组织及力学性能。方法利用搅拌摩擦焊机进行对接焊接,焊后制取金相试样观察焊接接头宏观形貌和显微组织,并测定其力学性能。结果7A52铝合金FSW焊接接头焊核区的面积随着焊接速度的增大而增大,当焊接速度为250mm/min时,焊接接头的焊核区面积最大,焊核区的显微组织都为细小的等轴晶,焊接接头横截面的焊核区呈明显"洋葱环"的形貌,而热力影响区的结构特征则呈现出了较高的塑性变形流线层。焊接接头显微硬度分布都呈现出"W"形变化,在焊接速度为150 mm/min时,焊接接头的平均抗拉强度能达到452 MPa,达到了母材抗拉强度的89%。结论通过对不同焊接速度下7A52铝合金FSW焊接接头的组织和性能进行研究,得到了不同焊接速度下焊接接头组织和力学性能。     

Estimation of Parameters of Universal Distribution of Moments of Failure of Products

A method is proposed for estimating the parameters of a mixture of exponential and Weibull distributions for which the accuracy of preliminary estimates obtained by graphical analysis is refined in accordance with the criterion of maximum likelihood. The efficiency of the proposed method is supported by the results of statistical modeling.     

Evaluation of optical properties of highly scattering media by moments of distributions of times of flight of photons

A novel method for the determination of the optical properties of tissue from time-domain measurements is presented. The data analysis is based on the evaluation of the first moment and the second centralized moment, i.e., the mean time of flight and the variance of the measured distribution of times of flight (DTOF) of photons injected by short (picosecond) laser pulses. Analytical expressions are derived for calculation of absorption and of reduced scattering coefficients from these moments by application of diffusion theory for infinite and semi-infinite homogeneous media. The proposed method was tested on experimental data obtained with phantoms, and results for absorption and reduced scattering coefficients obtained by the proposed method are compared with those obtained by fitting of the same data with analytical solutions of the diffusion equation. Furthermore, the accuracy of the moment analysis was investigated for a range of integration limits of the DTOF. The moment analysis may serve as a comparatively fast method for evaluating optical properties with sufficient accuracy and can be used, e.g., for on-line monitoring of optical properties of biological tissue.     

Analysis of the rate of propagation of the wave of change of boiling modes

An approximate analytical expression is derived for the velocity of the front of the wave of change of boiling modes on a rod and on a plate. The impact of the Thomson effect and of the heater orientation in the gravity field is included. Adequate agreement is demonstrated between the derived relations and experimental data.     

Estimation of potentialities of methods of summation of direct measurement errors

Conventional methods for summation of direct measurement errors are considered. Conditions under which these methods provide consistent results are stated. It is proposed to utilize for characteristic of the total error, its interval estimator or the half-sum of the value obtained by adding up its arithmetic and geometric random errors.Translated from Izmeritel'naya Tekhnika, No. 4, pp. 10–12, April, 1995.     

空压机轴承箱蜗壳温度探头油封改造

由于空压机进气侧轴承箱蜗壳温度探头密封效果不好,使空压机及其后续管道受到油污染。后将温度探头的O形圈密封改为骨架油封,杜绝了轴承箱漏油问题。文章简介空压机的结构和技术参数,详细介绍了骨架油封的制作和优点。     

Characteristics of mechanical properties of materials in studies of conditions of attainment of marginal states

It is shown that conditions of attainment of marginal states in the material of structural components are formulated on the basis of analysis of force and deformation criteria of formation and development of destruction. The parameters of these criteria are data on types of structural materials, standard and special characteristics of their mechanical properties, structural forms of considered elements of the equipment, and their operating stress loading. In this case, the construction of a system of state equations for describing interrelation of current damage, external actions, and responses to them is based on the concept of calculating variations in properties of materials at all stages of the design life cycle.     

Determination of parameters of microstructural inhomogeneity of deformation of metals by the method of modeling

The article suggests a method of evaluating the microstructural inhomogeneity of deformation of metals by modeling. The method includes the measurement of deformations of metal according to meshes of a dividing grid with small base and the calculation of the distribution parameters of microdeformations in model representation. It is shown that the modeling method makes it possible objectively to evaluate the microinhomogeneity of deformation of metals independently of the chosen mesh size of the dividing grid. New structural characteristics are introduced: the base and wave of variation expressing the degree of crumbling or amalgamation of metal grains by inhomogeneity of deformation.Translated from Problemy Prochnosti, No. 7, pp. 40–44, July, 1991.     

水三相点复现的不确定度评定

水三相点是开尔文热力学温度的唯一基准点，也是ITS-90国际温标重要的定义固定点。因此，水三相点不确定度分析对整个温标的建立、温度量值传递起着至关重要的作用。近3年来，中国计量科学研究院研制出一系列高质量的水三相点容器，加强了水三相点的研究，为不确定度的分析提供了更为可靠的实验依据。同时，不确定度的分析也是客观评价新研制容器性能的一个重要指标。因此，根据实验结果对新研制容器所复现的水三相点进行了不确定度评定。评定结果表明，其扩展不确定度为0．16mK(k=2．69，P=0．99)。