12~18 GHz GaAs MMIC低噪声放大器设计

采用GaAs工艺设计了一个12~18 GHz毫米波单片集成电路(MMIC)低噪声放大器(LNA)。采用三级单电源供电放大结构,运用最小噪声匹配设计、共轭匹配技术和负反馈结构,同时满足了噪声系数、增益平坦度和输出功率等要求。仿真表明：在12~18 GHz的工作频带内,噪声系数为1.15~1.41 dB,增益为27.9~29.1 dB,输出1 dB压缩点达到15 dBm,输入、输出电压驻波比(VSWR)系数小于1.72。     

CMOS宽带线性可变增益低噪声放大器设计

文章设计了一种48MHz~860MHz宽带线性可变增益低噪声放大器,该放大器采用信号相加式结构电路、控制信号转换电路和电压并联负反馈技术实现。详细分析了线性增益控制、输入宽带匹配和噪声优化方法。采用TSMC0.18μm RF CMOS工艺对电路进行设计,仿真结果表明,对数增益线性变化范围为-5dB~18dB,最小噪声系数为2.9dB,S11和S22小于-10dB,输入1dB压缩点大于-14.5dBm,在1.8V电源电压下,功耗为45mW。     

增益可调宽带CMOS低噪声放大器设计

设计了一种应用于超宽带系统中的可变增益宽带低噪声放大器。电路中采用了二阶巴特沃斯滤波器作为输入和输出匹配电路;采用了两级共源共栅结构实现电路的放大,并通过控制第二级的电流,实现了在宽频带范围内增益连续可调;采用了多栅管(MGTR),提高了电路的线性度;设计基于SMIC 0.18μm CMOS工艺。仿真结果显示,在频带3~5 GHz的范围内最高增益17 dB,增益波动小于1.8 dB,输入和输出端口反射系数分别小于-10 dB和-14 dB,噪声系数nf小于3.5 dB,当控制电压Vctrl=1.4 V时,IIP3约为2 dBm,电路功耗为16 mW。     

Low-power single-to-differential LNA at S-band based on optimised transformer topology and integrated ESD

A single-ended to differential low-power low-noise amplifier (LNA) designed and implemented in 0.18 mum CMOS technology is presented. The device takes advantage of a current reuse strategy by stacking two common-source differential transistor pair stages for minimum current dissipation, together with the design of optimised high Q differential transformers and inductors in order to minimise the impact of parasitics. The fully integrated, including ESD protection diodes, 2.1 GHz LNA consumes 1.1 mW at 1.2 V supply voltage and presents 29.8 dB gain, 4.5 dB noise figure, -21.1 dBm 1 dB compression point, -11.6 dBm input third-order intercept point and -12.3 dB input return loss performance.     

一种具有新型增益控制技术的CMOS宽带可变增益LNA

高速超宽带无线通信的多标准融合是未来射频器件的发展趋势,该文提出一种基于CMOS工艺、具有新型增益控制技术的宽带低噪声放大器(LNA),采用并联电阻反馈实现宽带输入匹配,并引入噪声消除技术来减小噪声以提高低噪声性能;输出带有新型6位数字可编程增益控制电路以实现可变增益。采用中芯国际0.13m RF CMOS工艺流片,芯片面积为0.76 mm2。测试结果表明LNA工作频段为1.1-1.8 GHz,最大增益为21.8 dB、最小增益8.2 dB,共7种增益模式。最小噪声系数为2.7 dB,典型的IIP3为-7 dBm。     

Design of a fully differential CMOS LNA for 3.1-10.6 GHz UWB communication systems

A fully differential complementary metal oxide semiconductor （CMOS） low noise amplifier （LNA） for 3.1-10.6 GHz ultra-wideband （UWB） communication systems is presented. The LNA adopts capacitive cross-coupling common-gate （CG） topology to achieve wideband input matching and low noise figure （NF）. Inductive series-peaking is used for the LNA to obtain broadband flat gain in the whole 3.1-10.6 GHz band. Designed in 0.18 um CMOS technology, the LNA achieves an NF of 3.1-4.7 dB, an Sll of less than -10 dB, an S21 of 10.3 dB with ±0.4 dB fluctuation, and an input 3rd interception point （IIP3） of -5.1 dBm, while the current consumption is only 4.8 mA from a 1.8 V power supply. The chip area of the LNA is 1×0.94 mm^2.     

2～12 GHz CMOS超宽带低噪声放大器设计

提出了一种基于双反馈电流复用结构的新型CMOS超宽带(UWB)低噪声放大器(LNA),放大器工作在2～12 GHz的超宽带频段,详细分析了输入输出匹配、增益和噪声系数的性能。设计采用TSMC 0.18μm RF CMOS工艺,在1.4 V工作电压下,放大器的直流功耗约为13mW(包括缓冲级)。仿真结果表明,在2～12 GHz频带范围内,功率增益为15.6±1.4 dB,输入、输出回波损耗分别低于-10.4和-11.5 dB,噪声系数(NF)低于3 dB(最小值为1.96 dB),三阶交调点IIP3为-12 dBm,芯片版图面积约为712μm×614μm。     

A CMOS variable gain low-noise amplifier with ESD protection for 5 GHz applications

This paper presents a variable gain low-noise amplifier (VG-LNA) for 5 GHz applications.The effect of the input parasitic capacitance on the inductively degenerated common source LNA's input impedance is analyzed in detail.A new ESD and LNA co-design method was proposed to achieve good performance.In addition,by using a simple feedback loop at the second stage of the LNA,continuous gain control is realized.The measurement results of the proposed VG-LNA exhibit 25 dB (-3.3 dB to 21.7 dB) variable gain range,2.8 dB noise figure at the maximum gain and 1 dBm IIP3 at the minimum gain,while the DC power consumption is 9.9 mW under a 1.8 V supply voltage.     

Low-power programmable gain CMOS distributed LNA

A design methodology for low power MOS distributed amplifiers (DAs) is presented. The bias point of the MOS devices is optimized so that the DA can be used as a low-noise amplifier (LNA) in broadband applications. A prototype 9-mW LNA with programmable gain was implemented in a 0.18-/spl mu/m CMOS process. The LNA provides a flat gain, S/sub 21/, of 8 /spl plusmn/ 0.6dB from DC to 6.2 GHz, with an input impedance match, S/sub 11/, of -16 dB and an output impedance match, S/sub 22/, of -10 dB over the entire band. The 3-dB bandwidth of the distributed amplifier is 7GHz, the IIP3 is +3 dBm, and the noise figure ranges from 4.2 to 6.2 dB. The gain is programmable from -10 dB to +8 dB while gain flatness and matching are maintained.     

A 0.18μm CMOS 3-5 GHz broadband flat gain low noise amplifier

A 3-5 GHz broadband flat gain differential low noise amplifier (LNA) is designed for the impulse radio uitra-wideband (IR-UWB) system. The gain-flatten technique is adopted in this UWB LNA. Serial and shunt peaking techniques are used to achieve broadband input matching and large gain-bandwidth product (GBW). Feedback networks are introduced to further extend the bandwidth and diminish the gain fluctuations. The prototype is fabricated in the SMIC 0.18 μm RF CMOS process. Measurement results show a 3-dB gain bandwidth of 2.4-5.5 GHz with a maximum power gain of 13.2 dB. The excellent gain flatness is achieved with ±0.45 dB gain fluctuations across 3-5 GHz and the minimum noise figure (NF) is 3.2 dB over 2.5-5 GHz. This circuit also shows an excellent input matching characteristic with the measured S11 below-13 dB over 2.9-5.4 GHz. The input-referred 1-dB compression point (IPldB) is -11.7 dBm at 5 GHz. The differential circuit consumes 9.6 mA current from a supply of 1.8 V.     

Design and optimization of CMOS LNA with ESD protection for 2.4 GHz WSN application

A new optimization method of a source inductive degenerated low noise amplifier(LNA) with electrostatic discharge protection is proposed.It can achieve power-constrained simultaneous noise and input matching. An analysis of the input impedance and the noise parameters is also given.Based on the developed method,a 2.4 GHz LNA for wireless sensor network application is designed and optimized using 0.18-μm RF CMOS technology. The measured results show that the LNA achieves a noise figure of 1.59 dB,a power gain of 14.12 dB, an input 1 dB compression point of-8 dBm and an input third-order intercept point of 1 dBm.The DC current is 4 mA under a supply of 1.8 V.     

A 2.1-6 GHz SiGe BiCMOS low-noise amplifier design for a multi-mode wideband receiver

A wideband low-noise amplifier (LNA) with ESD protection for a multi-mode receiver is presented.The LNA is fabricated in a 0.18-μm SiGe BiCMOS process,covering the 2.1 to 6 GHz frequency band.After optimized noise modeling and circuit design,the measured results show that the LNA has a 12 dB gain over the entire bandwidth,the input third intercept point (IIP3) is -8 dBm at 6 GHz,and the noise figure is from 2.3 to 3.8 dB in the operating band.The overall power consumption is 8 mW at 2.5 V voltage supply.     

一种新型900MHz CMOS低噪声放大器的设计

对两种低噪声放大器(LNA)的构架进行了比较,详细推导了共源LNA的噪声系数与输入晶体管栅宽的关系及优化方法,设计了一种采用0.6 μ m标准CMOS工艺,工作于900MHz的新型差分低噪声放大器.在900MHz时,噪声系数为1.5 dB的情况下可提供22.5 dB的功率增益,-3dB带宽为1 50MHz,S11达到-38dB,消耗的电流为5mA.     

Ka波段低噪声放大器的设计

利用pHEMT工艺设计了一个Ka波段微波单片低噪声放大器电路。电路采用四级放大的结构形式。利用微带电路实现射频输入、输出和级间匹配。采用多目标优化方法对电路增益、噪声系数、驻波比、稳定系数和输出1dB压缩点等特性进行了研究。设计出一个增益大于20dB,噪声系数小于1．0dB,1dB压缩点的输出功率在10dBm以上,性能优异的LNA。     

A 2.7-V 900-MHz CMOS LNA and mixer

A CMOS low-noise amplifier (LNA) and a mixer for RF front-end applications are described. A current reuse technique is described that increases amplifier transconductance for the LNA and mixer without increasing power dissipation, compared to standard topologies. At 900 MHz, the LNA minimum noise figure (NF) is 1.9 dB, input third-order intercept point (IIP3) is -3.2 dBm and forward gain is 15.6 dB. With a 1-GHz local oscillator (LO) and a 900-MHz RF input, the mixer minimum double sideband noise figure (DSB NF) is 5.8 dB, IIP3 is -4.1 dBm, and power conversion gain is 8.8 dB. The LNA and mixer, respectively, consume 20 mW and 7 mW from a 2.7 V power supply. The active areas of the LNA and mixer are 0.7 mm×0.4 mm and 0.7 mm×0.2 mm, respectively. The prototypes were fabricated in a 0.5-μm CMOS process     

2.45 GHz 0.18 μm全差分CMOS低噪声放大器设计

设计了一个基于TSMC 0.18 μm CMOS工艺的2.45 GHz全差分CMOS低噪声放大器.根据电路结构特点,采用图解法对LNA进行功耗约束下的噪声优化,以选取最优的晶体管栅宽;设计了仅消耗15 μA电流的偏置电路;采用在输入级增加电容的方法,在改善输入匹配网络特性的同时,解决了栅极电感的集成问题.仿真结果表明:LNA噪声系数为1.96 dB,功率增益S_(21)超过20 dB,输入反射系数S_(11)和输出反射系数S_(22)分别小于-30 dB和-20 dB,反向功率增益S_(12)小于-30 dB,1 dB压缩点和三阶互调输入点IIP3分别达到-17.1 dBm和-2.55 dBm,整个电路在1.8 V电源下功耗为22.4 mW.     

（英）CMOS毫米波低功耗超宽带共栅低噪声放大器

本文陈述了一个基于单端共栅与共源共栅级联结构的超宽带低噪声放大器(LNA)。该LNA用标准90-nm RF CMOS工艺实现并具有如下特征：在28.5到39 GHz频段内测得的平坦增益大于10 dB;-3 dB带宽从27到42 GHz达到了15 GHz,这几乎覆盖了整个Ka带;最小噪声系数(NF)为4.2 dB,平均NF在27-42 GHz频段内为5.1 dB;S₁₁在整个测试频段内小于-11 dB。40 GHz处输入三阶交调点(IIP3)的测试值为 2 dBm。整个电路的直流功耗为5.3 mW。包括焊盘在内的芯片面积为0.58*0.48 mm2_。     

A Fully Integrated Direct-Conversion Receiver for CDMA and GPS Applications

This paper describes a fully integrated zero-IF receiver for cellular CDMA and GPS applications. The single-chip zero-IF receiver integrates the entire signal path for CDMA and GPS bands, including a low-noise amplifier (LNA), I/Q down-converters, baseband channel selection filters (CSFs), a voltage-controlled oscillator (VCO), and a local oscillator (LO) distribution circuit for each band. The cellular-band LNA achieves a noise figure (NF) of 1.2 dB, input third-order intercept point (IIP3) of 11 dBm, and gain of 15.5 dB. Cellular I/Q down-converter and baseband circuitries show 9-dB composite NF, 9 dBm IIP3 and 60-dBm input second-order intercept point (IIP2) without IIP2 calibration. The measured LO leakage is less than -110 dBm at LNA input. The phase noise of the cellular VCO is -134 dBc/Hz at 900-kHz offset with 1.76-GHz carrier frequency. Total GPS signal path achieves NF of 1.7 dB and gain of 74 dB with 42-mA current. The receiver is fabricated in a 0.35-mum SiGe BiCMOS process and packaged in a 6 mm times 6 mm 40-pin micro-lead-frame. Handset measurements report that the receiver meets or exceeds all of the CDMA-2000 requirements     

S-band low noise amplifier using 1 μm InGaAs/InAlAs/InP pHEMT

This paper discusses the design of a wideband low noise amplifier (LNA) in which specific architecture decisions were made in consideration of system-on-chip implementation for radio-astronomy applications. The LNA design is based on a novel ultra-low noise InGaAs/InAlAs/InP pHEMT. Linear and non-linear modelling of this pHEMT has been used to design an LNA operating from 2 to 4 GHz. A common-drain in cascade with a common source inductive degeneration, broadband LNA topology is proposed for wideband applications. The proposed configuration achieved a maximum gain of 27 dB and a noise figure of 0.3 dB with a good input and output return loss (S₁₁ < -10 dB, S₂₂ < -11 dB). This LNA exhibits an input 1-dB compression point of -18 dBm, a third order input intercept point of 0 dBm and consumes 85 mW of power from a 1.8 V supply.     

一种5~6 GHz宽带全集成CMOS低噪声放大器

采用55 nm标准CMOS工艺,设计并流片实现了一种应用于Wi-Fi 6(5 GHz)频段的宽带全集成CMOS低噪声放大器(LNA)芯片,包括源极退化共源共栅放大器、负载Balun及增益切换单元。在该设计中,所有电感均为片上实现;采用Balun负载,实现信号的单端转差分输出;具备高低增益模式,以满足输入信号动态范围要求。测试结果表明,在高增益模式下该放大器的最大电压增益为20.2 dB,最小噪声系数为2.2 dB;在低增益模式下该放大器的最大电压增益为15 dB,最大输入1 dB压缩点为-3.2 dBm。芯片核心面积为0.28 mm²,静态功耗为10.2 mW。