用真空再流焊实现BGA的无铅无空洞焊接

BGA焊接后常常会在焊点中形成很多的空洞,特别是对于BGA的无铅焊接,由于焊接温度高,氧化严重,以及焊料的特殊性能决定了BGA的无铅焊接更容易形成空洞.空洞的产生不仅影响焊点的导热、导电性能,也会影响焊点的强度,从而对BGA工作的长期可靠性产生影响.分析了空洞产生的机理,以及用真空再流焊接实现BGA无铅、无空洞焊接的原理和工艺过程.指出真空再流焊接工艺在解决BGA的无铅、无空洞化焊接问题上确实是一项行之有效的方法.     

混装条件下BGA焊点空洞问题

阐述了在实际工作中遇到的混装BGA焊点空洞问题;介绍了常用的混装BGA焊接方法并对其利弊进行了分析;介绍了BGA焊点空洞的检验标准;通过对无铅BGA焊点与有铅BGA焊点的对比,分析了BGA焊点空洞的成因;从管理措施、工艺手段和操作经验等多个角度总结了控制BGA焊点空洞形成的诸多要素.     

基于几种典型焊接空洞问题的探讨

文章从几种典型的BGA焊接空洞案例出发,探讨了导致BGA空洞的根本原因和基本的改善方向,解读了关于BGA空洞的危害、接受标准及检查方式,并给出了焊接空洞发生时PCB的处理建议。     

BGA封装器件焊点缺陷X-射线检测法

讨论了BGA器件焊接的特点,并对BGA器件焊接过程中产生的缺陷进行了阐述,采用X-射线检测仪检测了BGA封装器件安装焊点的几种常见缺陷,分析、阐述了其图像与相应缺陷的关系,结果表明X-射线检测方法能够准确地检测出BGA封装器件安装中的各种焊点缺陷,并能够自动计算BGA封装器件安装焊点的空洞率,对空洞缺陷的快速检测和预防具有实际意义.     

BGA无铅焊点零空洞缺陷控制研究

在无铅BGA封装工艺过程中,通过不同组分的BGA焊球合金与焊膏合金组合焊接、焊膏助焊剂活性剂不同配比及其不同再流焊接条件等实验,对焊料合金和助焊剂配比、再流焊接峰值温度、再流保温时间等参数变化,以降低BGA焊点空洞缺陷进行了研究。结果表明选用相同或相似的BGA焊球和焊膏合金组合焊接、选用活性强的焊膏、选择焊接保温时间较长均有助于降低BGA焊点空洞缺陷产生的几率和空洞面积,BGA焊点最佳再流焊接峰值温度为240℃,当峰值温度设置为250℃时,BGA焊点产生空洞缺陷几率会比240℃高出25%～30%。     

BGA焊点可靠性工艺研究

伴随高密度电子组装技术的发展,BGA(Ball Grid Array)成为高密度、高性能、多功能及高I/O数封装的最佳选择。文章分析了影响BGA焊点可靠性的关键因素,特别提出了减少焊点空洞缺陷和提高剪切强度的主要措施,并通过试验优化出各工艺参数。结果表明:运用优化的工艺参数制作的BGA焊点,焊接空洞以及芯片剪切强度有了明显改善,其中对BGA焊接样品进行150℃、1000h的高温贮存后,焊点的剪切强度完全满足GJB548B-2005的要求。     

回流焊峰值温度对混装BGA焊点的影响研究

针对当前大量使用有铅焊料焊接无铅BGA的实际现状,通过调控有铅制程回流曲线的峰值温度,研究其对混装BGA焊点坍塌高度、空洞率及微观组织的影响。结果表明,峰值温度从210℃提升至225℃,无铅BGA焊球能够全部充分坍塌且高度保持一致;峰值温度为210℃时,混合焊点内的空洞率最低,随着峰值温度的升高,空洞尺寸和空洞率均有所增加;峰值温度为215℃时的微观组织最细小且尺寸分布最均匀,继续提升峰值温度,微观组织尺寸会随之增大。因此使用有铅焊料焊接无铅BGA的最佳峰值温度为215℃,与有铅制程保持一致。     

BGA焊点空洞问题分析

BGA器件已经广泛应用于各个领域,首先对BGA器件进行了简介,在给出其焊点质量检验合格判据后,针对BGA组装过程中常见现象空洞,分析了空洞产生的机理,并进一步说明空洞对焊点可靠性的影响。最后根据空洞产生机理提出了一些措施以减少和改善空洞。     

BGA空洞形成的原因及可接受标准

BGA空洞是BGA组装过程常见的工艺缺陷,本文系统介绍了BGA空洞形成的原因与主要影响因素,讨论了BGA空洞的可接受标准,提出了消除及减少空洞缺陷的主要措施。     

BGA空洞形成的机理及对焊点可靠性的影响

BGA空洞是BGA组装过程常见的工艺缺陷,系统介绍了BGA空洞形成的机理与主要影响因素,讨论了BGA空洞的接受标准及其对焊点可靠性的影响,提出了消除及减少空洞缺陷的主要措施.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Nanoimprint Lithography -A Next Generation High Volume Lithography Technique

IntroductionNanoimprint Lithography is a well-acknowl-edged low cost, high resolution, large area pattern-ing process. It includes the most promising methods,high-pressure hot embossing lithography (HEL) [2],UV-cured imprinting (UV-NIL) [3] and micro contactprinting (m-CP, MCP) [4]. Curing of the imprintedstructures is either done by subsequent UV-lightexposure in the case of UV-NIL or by cooling downbelow the glass transition temperature of the ther-moplastic material in case of HEL…     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

Influence of PVK ： NPB hole transporting layer on the characteristics of organic light-emitting devices

A doping system consisting of NPB and PVK is employed as a composite hole transporting layer （CHTL）. By adjusting the component ratio of the doping system, a series of devices with different concentration proportion of PVK ： NPB are constracted. The result shows that doping concentration of NPB enhances the competence of hole transporting ability, and modifies the recombination region of charge as well as affects the surface morphology of doped film. Optimum device with a maximum brightness of 7852 cd/m^2 and a power efficiency of 1.75 lm/W has been obtained by choosing a concentration proportion of PVK ： NPB at 1：3.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.     

Analysis of error performance on Turbo coded FDPIM

Due to variable symbol length of digital pulse interval modulation（DPIM）, it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation（FDPIM） method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.