埋空隙PSOI结构的耐压分析

提出了一种埋空隙PSOI(APSOI)RESURF器件结构,此结构利用空隙相对低的介电系数,在器件纵向突破了传统SiO2埋层的耐压关系,提高了击穿电压;硅窗口的存在缓解了有源区的自热效应;不同衬底的场调制作用进一步优化了表面电场分布.在相同击穿电压条件下,此结构较一般PSOI结构只需1/4厚度的埋层,当漂移区厚度和埋层厚度均为2μm时可获得600V以上的击穿电压.     

具有p型埋层PSOI结构的耐压分析

提出了一种具有p型埋层的PSOI器件耐压新结构,称为埋层PSOI(BPSOI).其耐压机理是,通过p型埋层电荷产生的附加电场调制作用,导致表面电场分布中产生新的峰而使击穿电压提高;p型埋层的电中性作用增加了漂移区优化的浓度而使比导通电阻降低.借助二维MEDICI数值分析软件,获得此结构较一般PSOI的击穿电压提高52%～58%、比导通电阻降低45%～48%.     

具有P型埋层PSOI结构的耐压分析

提出了一种具有p型埋层的PSOI器件耐压新结构,称为埋层PSOI(BPSOI).其耐压机理是,通过p型埋层电荷产生的附加电场调制作用,导致表面电场分布中产生新的峰而使击穿电压提高;p型埋层的电中性作用增加了漂移区优化的浓度而使比导通电阻降低.借助二维MEDICI数值分析软件,获得此结构较一般PSOI的击穿电压提高52%～58%、比导通电阻降低45%～48%.     

新型PSOI LDMOSFET的结构优化

针对沟道下方开硅窗口的图形化SOI(PSOI)横向双扩散MOSFET(LDMOSFET)进行了结构优化分析,发现存在优化的漂移区长度和掺杂浓度以及顶层硅厚度使PSOI LDMOSFET具有最大的击穿电压和较低的开态电阻.PSOI结构的RESURF条件为Nd·tsi=1.8～3×101 2cm-2.对结构优化的PSOILDMOSFET进行了开态输出特性模拟,输出特性曲线没有曲翘现象和负导现象,开态击穿电压可达到1 6V,器件有源区的温度降低了50℃.结构优化有利于提高器件性能和降低器件的开发成本.     

基于介质电场增强理论的SOI横向高压器件与耐压模型

SOI(Silicon On Insulator)高压集成电路(High Voltage Integrated Circuit,HVIC)因其具有高速、低功耗、抗辐照以及易于隔离等优点而得以广泛应用。作为SOIHVIC的核心器件,SOI横向高压器件较低的纵向击穿电压,限制了其在高压功率集成电路中的应用。为此,国内外众多学者提出了一系列新结构以提高SOI横向高压器件的纵向耐压。但迄今为止,SOI横向高压器件均采用SiO2作为埋层,且实用SOI器件击穿电压不超过600V;同时,就SOI横向器件的电场分布和耐压解析模型而言,现有的模型仅针对具有均匀厚度埋氧层和均匀厚度漂移区的SOI器件建立,而且没有一个统一的理论来指导SOI横向高压器件的纵向耐压设计。笔者围绕SOI横向高压器件的耐压问题,从耐压理论、器件结构和耐压解析模型几方面进行了研究。基于SOI器件介质层电场临界化的思想,提出介质电场增强ENDIF(Enhanced Dielectric LayerField)理论。在ENDIF理论指导下,提出三类SOI横向高压器件新结构,建立相应的耐压解析模型,并进行实验。(1)ENDIF理论对现有典型横向SOI高压器件的纵向耐压机理统一化ENDIF理论的思想是通过增强埋层电场而提高SOI横向器件的纵向耐压。ENDIF理论给出了增强埋层电场的三种途径:采用低εr(相对介电常数)介质埋层、薄SOI层和在漂移区/埋层界面引入电荷,并获得了一维近似下埋层电场和器件耐压的解析式。ENDIF理论可对现有典型SOI横向高压器件的纵向耐压机理统一化,它突破了传统SOI横向器件纵向耐压的理论极限,是优化设计SOI横向高压器件纵向耐压的普适理论。(2)基于ENDIF理论,提出以下三类SOI横向高压器件新结构,并进行理论和实验研究①首次提出低εr型介质埋层SOI高压器件新型结构及其耐压解析模型低εr型介质埋层SOI高压器件包括低εr介质埋层SOI高压器件、变εr介质埋层SOI高压器件和低εr介质埋层PSOI(PartialSOI)高压器件。该类器件首次将低介电系数且高临界击穿电场的介质引入埋层或部分埋层,利用低εr介质增强埋层电场、变εr介质调制埋层和漂移区电场而提高器件耐压。通过求解二维Poisson方程,并考虑变εr介质对埋层和漂移区电场的调制作用,建立了变εr介质埋层SOI器件的耐压模型,由此获得RESURF判据。此模型和RESURF判据适用于变厚度埋层SOI器件和均匀介质埋层SOI器件,是变介质埋层SOI器件(包括变εr和变厚度介质埋层SOI器件)和均匀介质埋层SOI器件的统一耐压模型。借助解析模型和二维器件仿真软件MEDICI研究了器件电场分布和击穿电压与结构参数之间的关系。结果表明,变εr介质埋层SOI高压器件的埋层电场和器件耐压可比常规SOI器件分别提高一倍和83%,当源端埋层为高热导率的Si3N4而不是SiO2时,埋层电场和器件耐压分别提高73%和58%,且器件最高温度降低51%。解析结果和仿真结果吻合较好。②提出并成功研制电荷型介质场增强SOI高压器件笔者提出的电荷型介质场增强SOI高压器件包括:(a)双面电荷槽SOI高压器件和电荷槽PSOI高压器件,其在埋氧层的一侧或两侧形成介质槽。根据ENDIF理论,槽内束缚的电荷将增强埋层电场,进而提高器件耐压。电荷槽PSOI高压器件在提高耐压的基础上还能降低自热效应;(b)复合埋层SOI高压器件,其埋层由两层氧化物及其间多晶硅构成。该器件不仅利用两层埋氧承受耐压,而且多晶硅下界面的电荷增强第二埋氧层的电场,因而器件耐压提高。开发了基于SDB(Silicon Direct Bonding)技术的非平面埋氧层SOI材料的制备工艺,并研制出730V的双面电荷槽SOILDMOS和760V的复合埋层SOI器件,前者埋层电场从常规结构的低于120V/μm提高到300V/μm,后者第二埋氧层电场增至400V/μm以上。③提出薄硅层阶梯漂移区SOI高压器件新结构并建立其耐压解析模型该器件的漂移区厚度从源到漏阶梯增加。其原理是:在阶梯处引入新的电场峰,新电场峰调制漂移区电场并增强埋层电场,从而提高器件耐压。通过求解Poisson方程,建立阶梯漂移区SOI器件耐压解析模型。借助解析模型和数值仿真,研究了器件结构参数对电场分布和击穿电压的影响。结果表明:对tI=3μm,tS=0.5μm的2阶梯SOI器件,耐压比常规SOI结构提高一倍,且保持较低的导通电阻。仿真结果证实了解析模型的正确性。     

全耗尽型浮空埋层LDMOS的耐压特性

提出了一种新的全耗尽型浮空埋层LDMOS(FB-LDMOS)结构.全耗尽n型埋层在器件的体内产生新的电场,该电场调制了漂移区电场,使得在降低漂移区漏端电场的同时提高了源侧和中部电场REBULF效应.分析了埋层的浓度、厚度、长度等对器件击穿电压的影响.借助二维仿真软件MEDICI,该新结构的击穿电压由传统LDMOS的585.8V提高到886.9V,提高了51.4%.     

全耗尽型浮空埋层LDMOS的耐压特性

提出了一种新的全耗尽型浮空埋层LDMOS(FB-LDMOS)结构.全耗尽n型埋层在器件的体内产生新的电场,该电场调制了漂移区电场,使得在降低漂移区漏端电场的同时提高了源侧和中部电场REBULF效应.分析了埋层的浓度、厚度、长度等对器件击穿电压的影响.借助二维仿真软件MEDICI,该新结构的击穿电压由传统LDMOS的585.8V提高到886.9V,提高了51.4%.     

非均匀厚度漂移区SOI高压器件及其优化设计

提出非均匀厚度漂移区SOI高压器件新结构及其优化设计方法. 非均匀厚度漂移区调制SOI层的电场并增强埋层电场,从而提高器件击穿电压. 考虑到这种调制效应,提出解析模型用以优化设计该新器件的结构参数. 借助解析模型,研究了电场分布和器件击穿电压与结构参数的关系. 数值仿真证实了解析模型的正确性. 具有3阶梯的非均匀厚度漂移区SOI器件耐压为常规结构SOI器件的2倍,且保持较低的导通电阻.     

非均匀厚度漂移区SOI高压器件及其优化设计

提出非均匀厚度漂移区SOl高压器件新结构及其优化设计方法.非均匀厚度漂移区调制SOI层的电场并增强埋层电场,从而 提高器件击穿电压.考虑到这种调制效应.提出解析模型用以优化设计该新器件的结构参数.借助解析模型,研究了电场分布和器件击穿电压与结构参数的关系.数值仿真'证实了解析模型的正确性.具有3阶梯的非均匀厚度漂移区SOl器件耐压为常规结构SOl器件的2倍,且保持较低的导通电阻.     

具有部分n埋层的高压SJ-LDMOS器件新结构

针对衬底辅助耗尽效应降低常规super junction LDMOS(SJ-LDMOS)击穿电压的不足,提出了一种新的具有部分n埋层的高压SJ-LDMOS器件结构.通过该部分n埋层,不仅补偿了由于衬底辅助效应所致的电荷不平衡现象,实现了高的击穿电压,而且该埋层在器件正向导通时为电流提供了辅助通道,减小了器件导通电阻.分析了器件结构参数和参杂对器件击穿电压和导通电阻的影响,结果表明文中所提出的新结构具有高的击穿电压、低的导通电阻以及较好的工艺容差等特性.此外,该结构与智能功率集成技术兼容.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Influence of polarization extinction ratio on distributed polarization coupling detection

Distributed polarization coupling in polarization-maintaining fibers can be detected by using a white light Michelson interferometer. This technique usually requires that only one polarization mode is excited. However, in practical measurement, the injection polarization direction could not be exactly aligned to one of the principal axes of the PMF, so the influence of the polarization extinction ratio should be considered. Based on the polarization coupling theory, the influence of the incident polarization extinction on the measurement result is evaluated and analyzed, and a method for distributed polarization coupling detection is developed when both two orthogonal eigenmodes are excited.     

Noise character analysis and the restraint of self-pulsation laser diodes

We calculate the Langevin noise sources of self-pulsation laser diodes, analyze the effects of active region noise and saturable-absorption region noise on the power fluctuation as well as period fluctuation, and propose a novel method to restrain the noise effects. A visible SIMULINK model is established to simulate the system, The results indicate that the effects of noise in absorption region can be ignored; that with the increase of DC injecting current, the noise effects enhance power jitter, and nevertheless, the period jitter is decreased; and that with external sinusoidal current modulating the self-pulsation laser diode, the noise-induced power jitter and period jitter can be suppressed greatly. This work is valuable for clock recovery in all-optical network.     

High-quality single-crystal CdSe nanoribbons and their optical properties

Large-scale synthesis of single-crystal CdSe nanoribbons is achieved by a modified thermal evaporation method, in which two-step-thermal-evaporation is used to control CdSe sources＇ evaporation. The synthesized CdSe nanoribbons are usually several micrometers in width, 50 nm in thickness, and tens to several hundred micrometers in length. Studies have shown that high-quality CdSe nanoribbons with regular shapes can be obtained by this method. Room-temperature photolumines-cence indicates that the lasing emission at 710 nm has been observed under optical pumping （266 nm） at power densities of 25-153 kW/cm^2. The full width half maximum （FWHM） of the lasing mode is 0.67 nm     

Propagation of hermite-cosh-gaussian beams passing through ABCD optical system with an annular aperture

By using the expansion of the aperture function into a finte sum of complex Gaussian functions, the corresponding analytical expressions of Hermite-cosh-Gaussian beams passing through annular apertured paraxially and symmetrically optical systems written in terms of ABCD matrix were derived, and they could reduce to the cases with squared aperture. In a similar way, the corresponding analytical expressions of cosh-Gaussian beams through annular apertured ABCD matrix were also given. The method could save more calculation time than that by using the diffraction integral formula directly.     

中国建立EB级存储实验室,致力云计算应用(英文)

正With the support of 863 programs,Sugon Information Industry Co.,Ltd.,set up a dawning EB-class storage laboratory to address massive data storage requirements and largescale cloud computing demonstration applications.The Dawning EB-class cloud storage system adopts advanced fault-tolerant architecture,efficient data fault-tolerant algorithms with user authentication and data encryption policies to deal with the"lost""wrong"and"stolen"problems of data for ensuring the reliability and safety of the EB-class storage system in the public network application environments.The Dawning EB-class Storage Laboratory taking advan-