网状WDM网中多播业务的共享保护设计

研究网状波分复用(WDM)光网络中动态多播业务的保护方案,提出一种共享保护和重配置(SPR)算法.该算法根据网络状态动态调整链路代价,为每个多播业务请求建立最小代价工作树,并为光树上互不重叠的工作段提供链路分离的保护段.当网络中发生链路失效时,进行业务段保护切换和局部资源重配置.仿真表明,该算法可以合理共享波长资源、平衡网络负载,有效保护WDM网中任意单链路失效,并在多链路失效情况下大大提高业务恢复能力.     

网络多播路由的改进编码软件设计与实现

传统网络多播路由编码方法采用多播分布树进行编码,但链路容量遭遇瓶颈,致使编码节点较多,导致浪费带宽资源的问题。在此提出基于Koetter指数时间的网络多播路由改进编码算法对编码软件进行设计,分析多播路由的总体设计,通过数据包编码转发模块在多播拓扑不相交路径上进行编码和转发多播数据包,利用输入模块实现网络多播路由和上游节点的信息交换,通过开关仲裁模块判断能够向特定输出端口传输信息的输入端口,利用死锁控制模块对出现死锁现象的路由节点进行检测,一段时间后使多播路由恢复正常的数据交换,通过输出模块对数据的输出进行管理。以降低带宽资源为目的,采用Koetter指数时间算法实现网络多播路由编码,并给出编码的详细代码。实验结果表明,所提方法不仅节省网络资源,而且显著降低多播路由时延,增强网络吞吐量。     

基于网络编码的多播路由算法性能分析

多播传输是目前通信系统中的一项关键技术,可以将相同的信息同时传向多个接收节点。该文提出一种基于网络编码的新的多播路由算法,该算法利用Dijkstra约简网络搜索源节点到各接收节点的路径族。仿真结果表明,该算法在资源消耗和负载均衡方面较传统的多播路由算法有更好的表现,同时性能也更接近基于网络编码的最小费用多播算法。最后,数学分析表明该算法具有较低的计算复杂度。     

k冗余多播网络中网络编码算法设计与分析

k冗余多播网络采用网络编码可实现最大多播速率k的信息传输。该文利用最大距离可分码已有成果,给出k冗余多播网络在不同发送速率下所需的最小有限域,构造最大距离可分码[n, k]生成矩阵,将其列向量作为信源输出链路的全局编码向量,设计网络码字,实现网络编码。应用实例表明该网络编码方法相对现有的通用网络编码算法而言,具有更低的计算复杂度。     

基于共享路径和网络编码的光组播容量优化

为了降低光组播路由 的光域网络编码代价和提高达到理论最大光组播容量的 概率,提出一种基于共享链路和网络编 码的优化光组播容量方法。首先设计一种从多条源－ 宿最短路径中选择能达到最大光组播容量的最短路径簇,然后在 最短路径簇中计算路径的共享度,选择共享度高的组播路径传输网络编码信息,构造网络编 码次数最少的光组播编码子图, 解决传统的网络编码组 播路由和最大共享度链路组播路由中存在的网络编码次数过多和达到最大光组播容量概率过 低的问 题。仿真结果表明:本文提出的方法具有最低的网络编码代价,能以最大的概率达到光组播 理论最大容量。     

光树分割和共享光路合并优化任多播阻塞率

针对弹性光互联数据中心网络中任多播业务的频谱利用率低和带宽阻塞率高等问题,论文提出了一种基于光树分割和共享光路合并算法.该算法选择对光树最大长度和调制等级影响较小的树枝加入光树,使生成光树频谱代价最小.当光树传输所需频谱资源不足时,该算法将光树分割为可选较高调制等级的多子光树传输,提高频谱利用率.当网络中有足够资源时,设计一种基于链路共享度的将满足条件的子光树合并到光树上传输的机制以降低频谱消耗.仿真结果表明：论文所提算法具有较低的带宽阻塞率和较高的频谱利用率.     

支持网络编码的认知无线自组网拓扑控制算法

对认知无线自组网中有限的带宽进行研究,提出支持网络编码的拓扑控制算法。算法分为3个阶段：初始拓扑构建阶段,利用最短路径算法为单播业务构建拓扑,利用基于网络编码的最短路径算法为多播业务构建K冗余拓扑;拓扑优化阶段,通过逐条删除满足一定条件的链路优化拓扑;拓扑恢复阶段,针对关键点失效,利用与失效链路不在同一路径簇且开销最小的链路恢复网络连通。仿真结果表明,算法能够提高无线资源复用率,增强网络抗毁性。     

基于传输路径质量的无线mesh网络可靠多播

提出了一种可靠多播网(RM)模型,探讨了无线链路和节点可靠性对多播路径选择的影响。首先,建立了无线链路的相关性和多播路径的可靠性模型,并提出了多播传输的可靠性判据;同时,结合首树算法和多路径树算法提出了构造可靠多播网的算法。可靠多播网具有并行的多播路径,通过在多播源节点和目的节点之间选择多播链路和节点构成了可靠的多播路径,提供了多播路径的"负荷分担"和"热备份"功能,从而支持了多播业务可靠性。     

一种基于网络编码的共享树组播算法

文章针对传统共享树组播算法在网络资源消耗和负载平衡方面的不足,提出了一种基于网络编码的共享树组播算法.该算法在减小网络编码节点个数,最大限度提高链路共享程度的情况下,对多点到多点的组播建立具有网络编码功能的共享树进行数据传输.仿真结果表明,该算法较传统共享树组播方法而言更能有效减少波长资源消耗并均衡网络负载.     

基于网络编码的非等长多播数据分发策略

提出了一种新的编码数据分发算法,该算法通过收集每个多播路径簇上承载业务信息的带宽,来确定编码后数据的分发策略,使编码节点能够对带宽不相同的数据进行处理并在解码节点正确解码,从而更加贴近现实网络.仿真结果表明,该算法在资源消耗和网络均衡方面较传统的多播算法有更好的表现.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Noise character analysis and the restraint of self-pulsation laser diodes

We calculate the Langevin noise sources of self-pulsation laser diodes, analyze the effects of active region noise and saturable-absorption region noise on the power fluctuation as well as period fluctuation, and propose a novel method to restrain the noise effects. A visible SIMULINK model is established to simulate the system, The results indicate that the effects of noise in absorption region can be ignored; that with the increase of DC injecting current, the noise effects enhance power jitter, and nevertheless, the period jitter is decreased; and that with external sinusoidal current modulating the self-pulsation laser diode, the noise-induced power jitter and period jitter can be suppressed greatly. This work is valuable for clock recovery in all-optical network.     

High-quality single-crystal CdSe nanoribbons and their optical properties

Large-scale synthesis of single-crystal CdSe nanoribbons is achieved by a modified thermal evaporation method, in which two-step-thermal-evaporation is used to control CdSe sources＇ evaporation. The synthesized CdSe nanoribbons are usually several micrometers in width, 50 nm in thickness, and tens to several hundred micrometers in length. Studies have shown that high-quality CdSe nanoribbons with regular shapes can be obtained by this method. Room-temperature photolumines-cence indicates that the lasing emission at 710 nm has been observed under optical pumping （266 nm） at power densities of 25-153 kW/cm^2. The full width half maximum （FWHM） of the lasing mode is 0.67 nm     

Propagation of hermite-cosh-gaussian beams passing through ABCD optical system with an annular aperture

By using the expansion of the aperture function into a finte sum of complex Gaussian functions, the corresponding analytical expressions of Hermite-cosh-Gaussian beams passing through annular apertured paraxially and symmetrically optical systems written in terms of ABCD matrix were derived, and they could reduce to the cases with squared aperture. In a similar way, the corresponding analytical expressions of cosh-Gaussian beams through annular apertured ABCD matrix were also given. The method could save more calculation time than that by using the diffraction integral formula directly.     

Influence of polarization extinction ratio on distributed polarization coupling detection

Distributed polarization coupling in polarization-maintaining fibers can be detected by using a white light Michelson interferometer. This technique usually requires that only one polarization mode is excited. However, in practical measurement, the injection polarization direction could not be exactly aligned to one of the principal axes of the PMF, so the influence of the polarization extinction ratio should be considered. Based on the polarization coupling theory, the influence of the incident polarization extinction on the measurement result is evaluated and analyzed, and a method for distributed polarization coupling detection is developed when both two orthogonal eigenmodes are excited.     

Call for Papers

正Communications—VLSI Researches and industries of telecommunications have been growing rapidly in the last 20 years and will keep their high growing pace in the next decade.The involved researches and developments cover mobile communications,highway and last-mile broadband communication,domain specific communications,and emerging D2D M2M communications.Radio communication steps into its