热变形对40CrMnMo钢的晶粒尺寸影响规律研究

采用了MMS-200热力模拟机以40CrMnMo钢为实验对象进行了热压缩试验,研究了变形温度850℃～1150℃,变形量0.8,应变速率在0.01～10s~(-1)条件下实验钢的热变形行为。通过分析高温下变形参数对流变应力和奥氏体晶粒尺寸的影响,建立40CrMnMo钢的稳态动态再结晶晶粒尺寸模型。结果表明:变形温度为850℃～1150℃,实验钢在应变速率0.01～0.1s~(-1)下发生连续动态再结晶,应变速率1～10s~(-1)下发生动态回复。通过引入Zener-Hollomon(Z)参数表征变形参数对稳态动态再结晶晶粒尺寸的影响,建立了稳态再结晶晶粒尺寸的数学模型,得出提高应变速率或变形温度较低能使Z参数增大,峰值应力升高且动态再结晶晶粒减小。     

一种非调质连杆用高碳微合金钢的热变形行为

用Gleeble-3500热力模拟试验机在温度为1 223～1 323 K,应变速率为0.2～10 s-1的条件下对一种非调质连杆用高碳微合金钢进行了热压缩变形试验,测得了其流变曲线,并观察了变形后的组织.试验结果表明,流变应力和峰值应变随变形温度的降低和应变速率的提高而增大.试验用钢在真应变为0.8,温度为1 223～1 323 K,应变速率为0.2～10 s-1的条件下,发生完全动态再结晶.测得试验用钢的热变形激活能为289.9 kJ/mol,并得出了其热变形方程,以及动态再结晶晶粒尺寸与Zener-Hollomon参数之间的关系和动态再结晶状态图.     

904L不锈钢动态再结晶行为

采用单道次热压缩试验,研究了904L钢在不同变形温度、不同应变速率下的真应力-应变曲线以及组织形貌,阐明了热加工过程中热变形参数对其在变形过程中发生的动态再结晶行为及微观组织演变规律的影响,揭示了其相应的软化机制。结果表明:变形温度越高,流变应力越小,动态再结晶体积分数越高,晶粒尺寸越大;同温度下,变形速率越小,应力峰值越小,晶粒尺寸越大且晶界越平直化;904L钢的动态再结晶行为随着变形温度的升高,应变速率的减小,应变量的增大而进行得越充分且较高的变形温度有利于动态再结晶的进行。     

Custom 450高强度不锈钢的动态再结晶行为

摘要：为了探究Custom 450钢的动态再结晶行为,采用Gleeble 3800热模拟试验机,在变形温度为1050~1200℃和应变速率为0.01~10s-1的变形条件下开展了单道次等温压缩试验。研究结果显示,在变形温度为1050~1200℃和应变速率为1.0~10s-1的变形范围内,钢虽发生了完全的动态再结晶,但应力应变曲线未表现出明显的应力峰值;钢的动态再结晶的晶粒尺寸随着变形温度的升高和应变速率的降低逐渐增大,当应变速率为001s-1时,动态再结晶晶粒发生长大。采用双曲正弦函数构建了Cutom 450钢的热变形方程,并建立了钢的动态再结晶动力学、临界应变、峰值应变及动态再结晶晶粒尺寸与Zener Holloman参数的定量关系。     

904L不锈钢动态再结晶行为

采用单道次热压缩试验,研究了904L钢在不同变形温度、不同应变速率下的真应力-应变曲线以及组织形貌,阐明了热加工过程中热变形参数对其在变形过程中发生的动态再结晶行为及微观组织演变规律的影响,揭示了其相应的软化机制。结果表明:变形温度越高,流变应力越小,动态再结晶体积分数越高,晶粒尺寸越大;同温度下,变形速率越小,应力峰值越小,晶粒尺寸越大且晶界越平直化;904L钢的动态再结晶行为随着变形温度的升高,应变速率的减小,应变量的增大而进行得越充分且较高的变形温度有利于动态再结晶的进行。     

CSP热轧TRIP钢动态再结晶行为研究

摘要：采用Gleeble-3500热模拟试验机,在温度为950~1150℃、应变速率为0.1~10s-1和变形量为65%的条件下研究了CSP热轧TRIP钢的动态再结晶行为,探讨了初始奥氏体晶粒尺寸对TRIP钢动态再结晶行为的影响。研究结果表明,初始奥氏体晶粒尺寸越小,变形温度越高,应变速率越慢时,TRIP钢中奥氏体越易发生动态再结晶。其中,粗晶试样（初始奥氏体晶粒尺寸为767.54μm）在1050~1150℃内变形时,将发生动态再结晶。其热变形激活能为361539.17J/mol,确定了Zener-Holloman参数与应变速率和温度的关系式,建立了动态再结晶临界应变模型、高温奥氏体流动应力模型和动态再结晶晶粒尺寸模型,理论模拟结果与试验结果吻合较好。     

Custom 450高强度不锈钢的动态再结晶行为

为了探究Custom 450钢的动态再结晶行为,采用Gleeble-3800热模拟试验机,在变形温度为1 050～1 200℃和应变速率为0.01～10 s~(-1)的变形条件下开展了单道次等温压缩试验。研究结果显示,在变形温度为1 050～1 200℃和应变速率为1.0～10 s~(-1)的变形范围内,钢虽发生了完全的动态再结晶,但应力应变曲线未表现出明显的应力峰值;钢的动态再结晶的晶粒尺寸随着变形温度的升高和应变速率的降低逐渐增大,当应变速率为0.01 s~(-1)时,动态再结晶晶粒发生长大。采用双曲正弦函数构建了Cutom 450钢的热变形方程,并建立了钢的动态再结晶动力学、临界应变、峰值应变及动态再结晶晶粒尺寸与Zener-Holloman参数的定量关系。     

Fe16Mn0.6C TWIP钢流变应力和临界动态再结晶行为

 利用Thermecmastor-Z热模拟实验机,得到了Fe16Mn0.6C TWIP钢在变形温度850~1150℃,应变速率0.03~30s-1条件下热压缩变形的真应力应变曲线。进而研究了变形温度、应变速率对Fe16Mn0.6C流变应力和临界动态再结晶行为的影响规律。结果表明,850~1150℃范围内Fe16Mn0.6C热变形的峰值应力随温度的升高而降低,随着应变速率的增大而升高;且在应变速率为0.03 s-1和30 s-1出现明显的应力峰值,材料发生了动态再结晶。最后采用线性回归方法计算出Fe16Mn0.6C的高温变形流变应力本构方程,得出热变形激活能为469kJ/mol;并通过应变硬化速率与流变应力曲线求出了该钢种动态再结晶临界条件与Z参数之间的关系。     

45V钢的动态再结晶

用热压缩的试验方法研究了45V非调质钢热变形中的动态再结晶,求得45V钢的动态再结晶激活能Q=345.56KJ/mol;变形条件与峰值应力的关系为:Z=2.088×10~8σp~(5.95);峰值应变与变形条件之间的关系为εp=7.86×10~(-3)Z~(O.125);动态再结晶晶粒尺寸与Z值之间的关系为d=4.6×10~5 Z~(-0.266)。     

Hastelloy C-276合金高温压缩的动态再结晶行为

在Gleeble-3500热模拟机上对Hastelloy C-276(C-276)合金在变形温度为1 000~1 250℃和应变速率为0.01~10.00s~(-1)的变形条件下进行了高温压缩试验,研究了C-276合金热变形过程中组织演变和动态再结晶行为。结果表明,随着变形温度的升高,动态再结晶晶粒尺寸增大,动态再结晶进行得越充分;随着变形程度的增加,动态再结晶体积分数增大,动态再结晶晶粒略有长大;该合金发生动态再结晶的临界应变ε_c与Z参数和ε_p之间的关系分别为:ε_c=7.67×10~(-4)Z~(0.144),ε_c≈0.78ε_p;该合金动态再结晶形核机制主要为晶界弓弯形核机制,也存在孪生诱发动态再结晶形核机制。C-276合金热变形过程中晶粒得到显著细化,组织的均匀性得到有效改善,选用适宜的热加工工艺,可以获得细小均匀的组织。     

Hot Compression Behavior of AsCast Precipitation Hardening Stainless Steel

 High temperature deformation characteristics of a semiaustenitic grade of precipitation hardening stainless steels were investigated by conducting hot compression tests at temperatures of 900-1 100 ℃ and strain rates of 0001-1 s-1. Flow behavior of this alloy was investigated and it was realized that dynamic recrystallization (DRX) was responsible for flow softening. The correlation between critical strain for initiation of DRX and deformation parameters including temperature and strain rate, and therefore, Zener Hollomon parameter (Z) was studied. Metallographic observation was performed to determine the as deformed microstructure. Microstructural observation shows that recrystallized grain size increases with increasing the temperature and decreasing the strain rate. The activation energy required for DRX of the investigated steel was determined using correlations of flow stress versus temperature and strain rate. The calculated value of activation energy, 460 kJ/mol, is in accordance with other studies on stainless steels. The relationship between peak strain and Z parameter is proposed.     

Hot Deformation Characteristics and Dynamic Recrystallization Mechanisms of a Newly Developed Austenitic Heat-Resistant Alloy

The hot deformation characteristics, microstructure evolution, and dynamic recrystallization (DRX) mechanism of the newly developed austenitic heat-resistant steel Fe–18Cr–10Ni–0.3Nb–2.5Cu were systematically investigated by thermal compression tests combined with microstructure characterizations. The activation energy (Q) map, Zener–Hollomon parameter (Z) map, and processing map were plotted according to the stress–strain curves to reveal the inherent connection between the three maps and the hot deformation characteristics of this alloy. The high η region in the processing map does not precisely correspond to the region where DRX developed. Nevertheless, the flow instability map accurately predicts the microstructure. The variation pattern of Z corresponded more closely to the hot deformation microstructure evolution than did the variation pattern of Q. The degree of DRX increases with decreasing Z. The optimal process parameters are 1000 °C/0.01 s⁻¹/0.8 and 1100 °C/10 s⁻¹/0.8 (temperature/strain rate/strain), and they result in complete DRX and a narrow range of Z values. The DRX mechanism at high strain rate is characterized by the combined enhancement of discontinuous DRX (DDRX), continuous DRX (CDRX), and twin-DRX (TDRX). The dominance of the particle-stimulated nucleation (PSN) mechanism at intermediate strain rate results in the formation of incompletely recrystallized microstructures with approximate orientation. Sufficient time at low strain rate promotes the development of DDRX and CDRX.

     

铸态超级双相不锈钢S32750热加工性能

 为研究热变形参数对铸态超级双相不锈钢S32750热变形行为和显微组织的影响,运用Gleeble-3800热模拟试验机对S32750进行不同温度和应变速率下的高温拉伸和压缩试验。结果表明,S32750在1000~1200℃范围内具有较好的热塑性。在变形温度较低、应变速率较低时,流变曲线表现出不同于单相不锈钢的“类屈服平台”特征;当应变速率较高或变形温度较高、应变速率较低时,流变曲线为典型的动态再结晶特征。微观组织演变显示,铁素体和奥氏体两相都发生动态再结晶,且铁素体的再结晶先于奥氏体。降低应变速率,提高变形温度,可促进动态再结晶发生。基于热变形动力学模型建立了本构方程,表观应力指数为3.99,热变形激活能为393.75kJ/mol。S32750的高温软化机制与Zener-Hollomon(Z)参数有关,随Z参数增加,热变形峰值应力增加。     

Numerical Simulation of Microstructure Evolution for SA508-3 Steel during Inhomogeneous Hot Deformation Process

Based on hot compression tests by a Gleeble-1500D thermo-mechanical simulator, the flow stress model and microstructure evolution model for SA508-3 steel were established through the classical theories on work hardening and softening. The developed models were integrated into 3D thermal-mechanical coupled rigid plastic finite element software DEFORM3D. The inhomogeneous hot deformation （IHD） experiments of SA508 3 steel were designed and carried out. Meanwhile, numerical simulation was implemented to investigate the effect of temperature, strain and strain rate on microstructure during IHD process through measuring grain sizes at given positions. The simulated grain sizes were basically in agreement with the experimental ones. The results of experiment and simulation demonstrated that temperature is the main factor for the initiation of dynamic recrystallization （DRX）, and higher temperature means lower critical strain so that DRX can be facilitated to obtain uniform fine microstructure.     

粗晶Mg-3Gd-1Zn合金高温压缩变形过程中的动态再结晶

研究了粗晶Mg-3Gd-1Zn合金在723 ～823 K,应变速率0.100 ～0.001s-1条件下单轴压缩变形过程中的动态再结晶行为.研究结果表明,其热压缩曲线为典型的动态再结晶型,峰值流变应力和稳态流变应力随温度的升高而减小,随应变速率的增大而增大;在该实验温度范围内其变形激活能约为140 kJ·mol-1;再结晶晶粒尺寸lnd与lnZ参数偏离线性关系,且变形温度对再结晶晶粒尺寸的影响比应变速率更大.利用金相和电子背散射技术(EBSD)对773 K,0.010 s-1条件下压缩不同变形量的Mg-3Gd-1Zn合金进行了组织表征,发现其动态再结晶大都发生在孪晶界及其与原始晶界的交叉处,主要为孪生诱发动态再结晶形核(TDRX)机制.再结晶形核初期形状不规则,晶界倾向于呈直角,随着应变量的增大,由于晶界的局部迁移,再结晶晶粒逐渐转变为稳定的等轴晶.     

Dynamic Recrystallization Behavior and Microstructure Evolution of Bridge Weathering Steel in Austenite Region

The austenite dynamic recrystallization (DRX) behavior and microstructure evolution of a bridge weathering steel was systematically investigated at a deformation temperature range of 800–1100°C and strain rate of 0.1–10 s^?1 by using hot compression test and optical microscopy. The stress exponent and hot deformation energy were obtained by regression method to determine thermal deformation constitutive equation. The curve of stress versus strain is used, combined with high order polynomial fitting, to accurately determine the critical value of DRX. The relationships between critical strain, critical stress, and Z parameter of the bridge weathering steel were obtained by regression method. Moreover, the influence factors of DRX kinetics of the bridge weathering steel were studied in the light of the experimental results. It is shown that the strain rate has a more significant effect on the rate of DRX than that of the deformation temperature, and there is almost 0.85 orders of magnitude increment in the rate of DRX as the strain rate increases an order of magnitude. The dynamically recrystallized grain size can be decreased with decreasing the deformation temperature and increasing the strain rate during the austenite deformation.     

High Temperature Deformation Behavior of 4340 Steel: Activation Energy Calculation and Modeling of Flow Response

The 4340 steel is extensively utilized in several industries including automotive and aerospace for manufacturing a large number of structural components. Due to the importance of thermo-mechanical processing in the production of steels, the dynamic recrystallization (DRX) characteristics of 4340 steel were investigated. Namely, hot compression tests on 4340 steel have been performed in a temperature range of 900–1200 °C and a strain rate range of 0. 01–1 s^?1 and the strain of up to 0. 9. The resulting flow stress curves show the occurrence of dynamic recrystallization. The flow stress values decrease with the increase of deformation temperature and the decrease of strain rate. The microstructure of 4340 steel after deformation has been studied and it is suggested that the evolution of DRX grain structures can be accompanied by considerable migration of grain boundaries. The constitutive equations were developed to model the hot deformation behavior. Finally based on the classical stress-dislocation relations and the kinematics of the dynamic recrystallization; the flow stress constitutive equations for the dynamic recovery period and dynamic recrystallization period were derived for 4340 steel, respectively. The validity of the model was demonstrated by demonstrating the experimental data with the numerical results with reasonable agreement.     

700℃超超临界锅炉材料GH4700合金热压缩行为

利用变形温度为1120~1210℃、应变速率为0.1~20 s-1以及变形量为15%~60%的等温热压缩实验研究了GH4700合金的热变形行为.通过对低温和高应变速率条件下的形变热效应进行修正,得到准确的流变曲线,推导出描述峰值应力与温度和应变速率等变形参数的本构方程,并得到GH4700合金热变形表观激活能为322 kJ.组织分析表明,动态再结晶是热变形过程中最主要的软化方式,再结晶形核方式为应变诱发晶界迁移,变形温度升高和应变速率增大均有利于再结晶形核.再结晶发展阶段,随着变形量的增大和变形温度的升高,动态再结晶比例增加,在应变速率-温度坐标中,再结晶比例等值线呈反"C"形式.采用分段函数描述了不同应变速率下GH4700合金动态再结晶晶粒尺寸与变形参数的关系.