共查询到19条相似文献,搜索用时 109 毫秒
1.
用均相钠还原得到的纳米氮化钽粉在1 350℃进行不同时间的热处理,热处理后的粉末制成烧结体并进行阳极氧化过程。通过XRD和场发射扫描电镜分析了粉末的物相结构和形貌,研究了热处理时间和压制密度对氮化钽粉末电性能的影响。结果表明:热处理温度为1 350℃、热处理时间40min、压制密度约4g/cm时氮化钽阳极块体有较高的比容和较低的漏电流常数。 相似文献
2.
氧含量对钽电解电容器阳极氧化膜形成及漏电流的影响 总被引:3,自引:0,他引:3
针对阳极氧化膜在钽电解电容器中所起的重要作用,对比分析了钽阳极块中氧含量对其形成及电性能的影响,并简述了有关影响机理。结果表明:钽阳极块中的氧含量主要由原料钽粉中的杂质氧含量所决定,且与阳极块的压制、烧结及赋能条件等相关;杂质氧对阳极氧化膜形成不利,是造成电容器漏电流增大的主要因素之一。 相似文献
3.
高比容钽粉的赋能工艺研究 总被引:2,自引:0,他引:2
针对高比容钽粉的特性,分析了与赋能工艺的适应性及影响氧化膜质量的因素。在高比容钽粉应用中,本试验采用加柠檬酸等混合赋能液,先45℃低温升压、后高温恒压以及大气热处理相结合的赋能工艺,制得性能优良的钽阳极氧化膜,使电容器质量明显提高。 相似文献
4.
5.
本文根据高比容钽粉的特性,对赋能溶液组成进行了研究,认为采用添加适量柠檬酸的磷酸赋能液,先45℃低温升压后85℃高温恒压,以及大气热处理相结合的赋能工艺,可获得性能优良的阳极氧化膜,使钽电容器质量明显提高. 相似文献
6.
7.
采用K_2TaF_7金属钠还原—高温高真空煅烧—镁还原脱氧工艺制备了电容器用高比容钽粉,系统研究了高真空和一定的升温速率下,煅烧温度、煅烧时间对钽粉微观结构和高压电性能的影响。用场发射式扫描电镜(FESEM)、BET分析仪和激光粒度分布仪(LDSA)对电容器用高比容钽粉的微观结构进行表征,对该钽粉制成的烧结阳极的湿式电性进行检测。结果表明:随着煅烧温度的升高或煅烧时间的延长,粉末团聚体的尺寸增大,烧结颈变粗,团聚体的大小趋于均匀一致,团聚体之间微细孔隙明显减少;钽粉烧结阳极的电性能在高压(大于55 V)形成时得到优化,表现为漏电流(LC)小,容量(CV)高,损耗(tgδ)小,但低压(小于40 V)形成时钽粉烧结阳极的容量(CV)低。研究认为,比表面积介于1.30~1.50 m~2·g~(-1)的还原粉在1300℃煅烧40 min,钽粉综合性能最优。 相似文献
8.
本文阐述了以硝酸作电解质溶液,用电化学方法回收钨和钴的研究结果。本法包括碳化物材料的阳极氧化,以生成不溶性的钨酸(H_2WO_4),并使钴离子转入溶液中。以硝酸浓度、电流密度、温度和时间作变量,探索了碳化钨的氧化和钴的溶解同时进行的条件。研究发现,加入钴、硝酸铵或高氯酸钾对碳化钨的氧化有促进作用。从硝酸盐溶液中沉积钴的电流效率非常低。通过极化作用曲线研究了烧结碳化物的阳极行为,讨论了恒电压溶解和电极反应。 相似文献
9.
10.
刘绍蕖 《稀有金属与硬质合金》1989,(1):50-53
钽电解电容器是用钽粉压制成多孔的片状毛坯后烧结而成的。烧结块本身趄阳极作用。经阳极化处理后,烧结块中孔隙表面形成一层非常薄的(一般为500—5000(?))氧化膜电介质,然后往孔隙里渗渍电解液,即成阴极:也可以渗渍另外一种适当的溶液, 相似文献
11.
研究了温度、电流密度和电解液pH值等对硫酸体系中Ni MnO2 同时电解过程的影响 ,通过正交试验确定了电解过程的最佳工艺条件为 :[Ni2 +] 90 g/L ;[Mn2 +] 30 g/L ;pH 3 5;90℃ ;电流密度 16 5A/m2 ;[H3 BO3 ] =15g/L ,槽电压 2 86V ,此时阴极电效为 99 88% ,阳极电效接近 10 0 % ,得到的阴极镍纯度为 99 87% ,阳极MnO2 品位为 87 85%。 相似文献
12.
A. A. Palant A. M. Levin O. M. Levchuk V. A. Bryukvin 《Russian Metallurgy (Metally)》2013,2013(7):497-500
Technological foundations are developed for the electrochemical oxidation of nickel superalloys containing alloying elements Re, Ta, Nb, Co, W, Cr, Mo, and Al. It is shown that nickel, cobalt, and aluminum pass to a sulfuric acid solution when an asymmetric sinusoidal industrial-frequency alternating current is applied and 70–75% tungsten, molybdenum, tantalum, niobium, and rhenium are concentrated in an anode cake. When a nitric acid electrolyte is used, rhenium, nickel, cobalt, aluminum, and chromium pass to a solution and tungsten, molybdenum, tantalum, and niobium are concentrated in an anode cake. Technological versions of the processing of the oxidation products with the formation of marketable products are discussed. 相似文献
13.
钽阳极氧化膜生成机理的探讨 总被引:3,自引:0,他引:3
用交流阻抗法对钽阳极氧化膜生成机理进行了研究。提出了钽的氧化反应式及反应控制步骤;得出其氧化膜电容量随着氧化电位的增加而减少,阻抗与阳极化行为存在相关关系。 相似文献
14.
温度对电解二氧化锰工艺影响的研究 总被引:1,自引:0,他引:1
电解Mn的影响因素多于电解MnO2,所以试图研究在低温下电解MnO2来解决同槽电解Mn和MnO2温度差异问题。通过对比试验,研究以钛板为阳极在MnCl2-HCl溶液中和在Mn-SO4-H2SO4溶液中、以钛钌板为阳极在MnCl2-HCl溶液中温度对电解二氧化锰的电流效率和槽电压的影响,结果表明以钛钌板为阳极在MnCl2-HCl溶液中电解MnO2,低温下(45℃时)就具有低且稳定的槽压(-2.7 V)和高的电流效率(45℃时,ηA70%;55℃时,ηA90%)。X衍射试验表明:以钛钌板为阳极在MnCl2-HCl溶液中45℃电解沉积的物质是γ型二氧化锰。 相似文献
15.
16.
The electrodeposition of copper from acidified aqueous copper sulfate solution in cells equipped with fluidized cathodes has
been studied. Cells used were of a cylindrical geometry and a rectangular geometry, 150 amp and 1,000 amp nominal current,
respectively. In the smaller cell, current efficiency, energy consumption, and freedom from operating problems were measured
as a function of particle size, anolyte flow, temperature, acid concentration, anode geometry, and diaphragm material. Runs
in the larger cell demonstrated the technical feasibility of copper electrowinning on this scale, but power consumptions were
high, due to excessive voltage drops in the anode side of the cell. A mathematical model was developed and shown to be capable
of a semiquantitative prediction of the important aspects of cell behavior.
Formerly with the Department of Materials Science and Mineral Engineering, University of California, Berkeley, CA 相似文献
17.
18.
分析了掺杂剂对电容器级钽粉性能的影响,重点分析了不同掺杂剂含量下钽粉的物理性能、化学成分及电性能的变化。研究表明,在相同的工艺条件下,随着掺杂剂含量的增加,钽粉的氧含量有增加趋势,钽粉的松装密度、费氏粒径呈降低趋势,-0.043 mm细粉含量有所增加,漏电流、容量及收缩率呈上升趋势、击穿电压呈下降趋势。 相似文献
19.
The nitrogen solubility in liquid Fe-Ta, Fe-Cr-Ta, Fe-Ni-Ta, and Fe-18 pet Cr-8 pet Ni-Ta alloys was measured using the Sieverts’
method. The experiments covered the temperature range from 1782 to 2031 K, and tantalum contents from 2.0 to 20.0 wt pct Ta.
Nitrogen solution obeyed Sieverts’ law and no nitride precipitation was observed in this concentration range. Tantalum increases
the nitrogen solubility and the heat of solution of nitrogen is more negative at higher tantalum contents in these alloys.
The excess enthalpy and entropy of solution of nitrogen were determined. The first and second order interaction parameters
between nitrogen and tantalum were determined as a function of temperature, e
N
Ta
= -101.7/T + 0.018 and e
N
TaTa
= -3.27/T + 0.0022. The effects of alloying elements on the activity coefficient of nitrogen were measured and the second
order cross-interaction parameters between nitrogen and Ta with Cr and Ni were determined at 1873 K as e
N
CrTa
= 0.00052 and e
N
NiTa
= 0.00045. 相似文献