Effects of rare earth on inclusions and corrosion resistance of 10PCuRE weathering steel

The types,morphologies and distributions of nonmetallic inclusions in Cu-P weathering steels with and without rare earth were analyzed through a quantitative image analyzer,scanning electron microscopy(SEM)and energy dispersive spectroscopy(EDS)attached to SEM.Solid-soluble content of rare earth in the steels was analyzed by non-aqua electroanalysis and ICP.The results showed that rare earth modified the types and the morphologies of inclusions in the weathering steels.The small spherical rare earth oxysulfides and rare earth sulphides replaced the elongated MnS inclusions in the RE weathering steels.The rare earth inclusions dispersedly distributed and most inclusions were smaller than 2 μm in size.The optimum content of RE was 0.0065%-0.016% for 10PCuRE weathering steels containing about0.002% oxygen and 0.004% sulfur.Solid-soluble content of rare earth in steels was(14-20)x 10-6,which can act as a micro-alloying element.The corrosion resistance of 10PCuRE weathering steels and Q235 were studied by dry-wet cyclic immersion test.Their corrosion rates were obtained respectively.The polarization curves and pitting corrosion behaviors of weathering steels with and without rare earth were measured by electrochemical methods.The corrosion resistance of Cu-P weathering steels was improved by adding an appropriate amount of rare earth.Less and fewer rare earth inclusions largely decreased pitting susceptibility and rate of pit propagation.The pitting potential and the resistance against pitting corrosion of the RE weathering steel were significantly improved due to the modification of rare earth to inclusions.     

Lanthanide NIR luminescence for telecommunications, bioanalyses and solar energy conversion

Present-day advanced technologies heavily rely on the exciting magnetic and spectroscopic properties of lanthanide ions. In particular, their ability to generate well-characterized and intense near-infrared (NIR) luminescence is exploited in any modern fiber-optic telecommunication network. In this feature article, we first summarize the whereabouts underlying the design of highly luminescent NIR molecular edifices and materials. We then focus on describing the main trends in three applications related to this spectral range: telecommunications, biosciences, and solar energy conversion. In telecommunications, efforts concentrate presently on getting easily processable polymer-based waveguide amplifiers. Upconversion nanophosphors emitting in the visible after NIR excitation are now ubiquitous in many bioanalyses while their application to bio-imaging is still in its early stages; however, highly sensitive NIR-NIR systems start to be at hand for both in vitro and in vivo imaging, as well as dual probes combining magnetic resonance and optical imaging. Finally, both silicon-based and dye-sensitized solar cells benefit from the downconversion and upconversion capabilities of lanthanide ions to harvest UV and NIR solar light and to boost the overall quantum efficiency of these next-generation devices.     

Thermal and radiative characteristics of oxyfluoride glass singly doped with lanthanide ions

Rare earths-doped oxyfluoride glasses based on germanium oxide and lead fluoride were prepared from commercial raw materials. The glasses with general composition of 50GeO2-(50-x-y)PbO-yPbF2-xLnF3 (Ln=Pr3+-Yb3+), contained different concentrations of optically active dopants (x=0.2 mol.% and 2 mol.%) and PbF2 (y≤15 mol.%). The differential thermal analysis (DTA) was used to determine both thermal characteristic and thermal stability properties of the glasses in the function of the kind of dopant, its concentration, and a glass composition. Characteristic glass temperatures such as glass transition temperature (Tg), glass crystallization temperature (Tc) and temperature corresponding to the maximum of the crystallization rate (Tpc) were evaluated. On the basis of obtained results, the thermal stabilities of glasses under study were evaluated using various thermal stability criteria (Dietzel factor ?T, Saad-Poulain factors H' and S). It was found that the increase in rare earth fluoride contents influenced thermal characteristics when the characteristic temperatures of the individual glass was shifted towards higher values. The effect of the PbF2 content and the kind of rare earth impurity on the glass stability was observed. Absorption spectra of lanthanide-doped glasses were measured at room temperature and used to determine the phenomenological intensity parameters Ωt and next, to estimate radiative properties of lanthanide ions in this matrix. Radiative transition probabilities of luminescent states of Ln3+, branching ratios and radiative lifetimes were determined. The variation of the Ωt along the lanthanide series was presented and discussed.     

Evaluation of D113 cation exchange resin for the removal of Eu(Ⅲ) from aqueous solution

Batch adsorption experiments were conducted for the adsorption of Eu(Ⅲ) ions from aqueous solution by D113 resin. The results indicated that D113 resin could adsorb Eu(Ⅲ) ion effectively from aqueous solution. The adsorption was strongly dependent on pH of the medium with enhanced adsorption as the pH turned from 3.50 to 7.00 and the optimal adsorption condition was in HAc-NaAc medium with pH value of 6.50. The maximum uptake capacity of Eu(Ⅲ) ions was 290.9 mg/g D113 at 298 K, at an initial pH value of 6.50. The overall adsorption process was best described by Lagergren-first-order kinetics. When Freundlich and Langmuir isotherms were tested, the latter had a better fit with the experimental data. The thermodynamic parameters such as free energy (G) which were all negative, indicated that the adsorption of Eu(Ⅲ) ions onto D113 resin was spontaneous and the positive value of enthalpy (H) showed that the adsorption was endothermic in nature. Thomas model was applied to experimental column data to determine the characteristic parameters of column useful for process design. Furthermore, Eu(Ⅲ) could be eluted by using 3.0 mol/L HCl solution and the D113 resin could be regenerated and reused.     

Phase structure and temperature dependent luminescence properties of Sr2LiSiO4F: Eu2+ and Sr2MgSi2O7: Eu2+ phosphors

Green-emitting Sr2LiSiO4F:Eu2+ and blue-emitting Sr2MgSi2O7:Eu2+ phosphors were synthesized by the conventional high temperature solid-state route,respectively.Their structures and photoluminescenee properties were comparatively investigated.It was found that the mixture phases of Sr2MgSi2O7 and SrF2 were obtained when a part of Sr2+ in Sr2LiSiO4F was replaced by some amount of Mg2+ in order to design the possible SrMgLiSiO4F:Eu2+ phosphor.Based on the photoluminescence analysis,Sr2LiSiO4F:Eu2+ phosphor exhibited a green broad emission band of main peak at 513 nm under the excitation of 365 nm,while the Sr2MgSi2O7:Eu2+ and SrMgLiSiO4F:Eu2+ phosphor showed blue emission centered at 467 nm.The temperature dependent photoluminescence properties and room temperature decay time for the three kinds of phosphors were also discussed in this paper.     

Er3+-substituted W-type barium ferrite: preparation and electromagnetic properties

Er3+-substituted W-type barium ferrites Ba1-xErx(Zn0.3Co0.7)2Fe16O27(x=0.00,0.05,0.10,0.15,0.20)were synthesized by polymer adsorbent combustion method.Samples were characterized by X-ray diffraction analysis(XRD),X-ray fluorescence(XRF),scanning electron microscopy(SEM)and network analyzer to investigate the relationships among Er3+concentration,crystal structure,surface mcrphology and electromagnetic properties.All the XRD patterns showed pure phase of W-type barium ferrite when x≤0.15,while the impurity phase of ErFeO3 appeared when x=0.20.The pure W-type barium ferrite showed a hexagonal flake shape.In addition,the microwave electromagnetic properties of samples were analyzed in the frequency range of 2-18 GHz.It was indicated that the electromagnetic properties were significantly improved when Er3+doping content was 0.10.The reasons were also discussed using electromagnetic theory.The optimized ferrite exhibited excellent microwave absoption performance.The maximum of reflection loss(RL)reached about-27.4 dB and RL was below-10dB at the frequency range from 8.4 GHz to 18 GHz,when the thickness was 2.6 mm.     

EXAFS investigation and luminescent properties of nanosized Tb: Lu2O3 phosphors

Nanosized terbium doped Lu2O3 phosphors were synthesized via a modified co-precipitation processing.The as-prepared Tb:Lu2O3 phosphors was consisted of well crystallized nanosized sphere particles with a diameter of about 30 nnx Local structure of Tb ions in Lu2O3 lattice was investigated by an analytical approach based on Fourier transformation of the extended X-ray absorption fine structure(EXAFS) data.X-ray near edge structure (XANES) spectra suggested that all Tb ions doped were tervalonce.EXAFS results indicated that Tb ions have entered the Lu2O3 cubic lattice by means of solid solution.The coordination number and first shell Tb-O distance dropped with the increasing of Tb concentration.Emission spectra of the phosphors was shown to be typical for Tb3+ with main components at 542,550 and 490 nm,derived from irradiative relaxation of 5D4 level.The emission intensity decreased severely with the increasing of Tb concentration from 1 mol.% to 15 tool.%,suggesting a significant concentration quenching above 1 mol.% Tb.The reduction of emission intensity was interpreted by higher distortion derived relaxation among the surface state resident Tb3+ ions.     

Process optimization of electroless copper plating and its influence on electrochemical properties of AB5-type hydrogen storage alloy

The amount of Cu coating by chemical plating was investigated based on quadratic regression orthogonal experimental design being adapted to the variation law of temperature,pH value and Ni2+concentration,and the relevant regression equation was expressed as y=2.1609+0.5295×10-3T2-0.0342P2-0.0265N2+0.0023TP+0.0020TH+0.0199PN-0.0959T+0.3814P-0.2073N.The results showed that the deposition rate augmented with the increasing in temperature,pH value and Ni2+concentration.The experimental parameters of the optimal coating were temperature 75 ℃,pH value 8.5 and Ni2+concentration 1.2 g/L.The electrochemical tests indicated that the cycle stability increased from 60.66% to 75.58%,indicating that the treated alloy exhibited better corrosion resistance.     

Multi-Pass Simulation of Heavy Plate Rolling Including Intermediate Forced Cooling

Thermomechanical Controlled Processing (TMCP) including accelerated cooling after the final hot rolling pass is a well-established technology,widely applied in HSLA steel plate production.However,there are still certain limitations,especially for thicker plate.The rolling schedule includes a long holding period (HP) after the roughing stage to allow the temperature to fall sufficiently for optimised TMCP during finishing.Intermediate Forced Cooling (IFC) applied during the HP can increase productivity by decreasing the required hold time,can restrict austenite grain growth,and can also improve the subsequent strain penetration in thick plate with further metallurgical benefits.Multi-pass plane strain compression (PSC) tests have been performed on the thermomechanical compression (TMC) machine at Sheffield University including different severities of IFC.Clearly it is impossible to simulate all aspects of the temperature and strain gradients present in thick plates in laboratory specimens,and most of the tests were conducted at temperatures and strains calculated by Finite Element modelling as relevant to specific positions through the plate thickness.However,some aspects of the gradients were addressed with tests using cold platens.The results have indeed shown that IFC can shorten the HP and reduce austenite grain growth and its variation across thick plate.     

Overview of Particles and Bubbles in Continuously Cast Steel

This paper gives an overview of phenomena associated with particles and bubbles in continuously cast steel. During steel processing from deoxidation to solidification the inclusion population undergoes changes with opportunities of removal. Flotation is an important separation mechanism. Inclusion particles may accumulate in the solidifying strand, thus forming enriched bands, which depend on the type of casting machine. Bubbles are created during inert gas injection. They also change in size, can float out, but also form accumulation bands. The interaction of bubbles and particles is discussed. Internal structure that recently has been observed on the inner surface of bubbles will be reviewed.     

烦恼 快乐 艺术——池莉“人生三部曲”解读

池莉的"人生三部曲"--<烦恼人生>、<不谈爱情>、<太阳出世>诉尽了普普通通的市民烦恼,小说中主人公被柴米油盐、吃喝拉撒、老婆孩子等琐事所烦着,从而构成他们的"烦恼人生".然而池莉通过自己的艺术创作,以积极的人生态度,又让读者体会到生活本身的快乐,"烦恼人生"中包含着"快乐人生".     

天铁热力风机升级改造方案设计

通过对天铁集团高炉现状、风机现状的分析,提出了对热力厂风机升级改造的规划,确定了实施方案.该方案实施后将彻底改变风机渐进式改造的现象,使新高炉的备用机组发挥更大的作用,可增加现有高炉的风压、风量,使现有高炉的产量、冶炼强度进一步提高.     

属性块在工程图形中的研究与应用

介绍了在工程图形中用属性块标注表面粗糙度的方法.采用属性块不仅能避免大量重复性的工作,还能节省大量的存储空间,具有提高绘图速度、质量,便于修改,资源共享等应用价值.     

Experimental and DFT study on cerium inclusions in clean steels

To provide insights into deforming Ce-O-S-Al inclusions in steels and improving the mechanical properties,the evolution process of such harmful inclusions in clean steels was investigated by thermodynamic calculation,metallographic examination and first-principles calculation in this paper.For the tested IF steel,the thermodynamic analysis results are consistent with the calculated formation enthalpy.After Ce addition,the inclusions are transformed from Al₂O₃and TiN-Al₂TiO₅-Al₂O₃to Ce2O₃,Ce₂O₂S,CeAlO₃,TiN-Al₂TiO₅-Ce₂O₃and TiN-Al₂TiO₅-Ce₂O₂S composite inclusions,which can be confirmed by metallographic examination.The elastic constants were calculated,and the bulk modulus,Young's modulus,shear modulus and Poisson's ratio were evaluated by the Voigt-Reuss-Hill(VRH)approximation.All inclusions except Ce₂O₃show apparent brittleness.TiN,Al₂O₃,Al₂TiO₅and CeAlO₃present much higher hardness than iron matrix,while the hardness of Ce2O₃or Ce₂O₂S is close to that of iron matrix.The thermal expansion coefficients of Ce₂O₃and CeAlO₃are close to that of iron matrix,whereas,Ce₂O₂S inclusion has largely different thermal expansion coefficient from iron matrix and may deteriorate the steel performance at higher temperatures.The relatively small differences between Ce inclusions and iron matrix in terms of hardness,toughness,brittleness,and thermal expansion coefficient can explain the improvement of the mechanical properties of the tested steel.     

Revealing Liquid Metal Target Malfunctions by Means of Vibrations and Sound Pressure Monitoring

In the following paper an experiment dedicated to the accident protection system of a Liquid Metal Target is presented.The test was carried out at the liquid metal test stand(LIMETS)at PSI in which the malfunctioning of a target during operation was simulated.It could be demonstrated that measurements and the proper(on-line)analysis of target vibrations and surrounding sound pressure fields allow the detection of a malfunctions like deformation or detaching of structural elements immeresed in the flow.Amplitudes of acceleration sensors and microphones signals as well as frequencies of the disturbances’signals are prospective parameters to be used in an automated accident protection system as indicators for a target malfunction.     

Recent progress report on DNA B-Z transition modulated by rare earth-amino acid complex and Alzheimer's disease amyloid beta

Rare earth dements have unique physical, magnetic, luminescent and catalytic properties. They have been successfully used as medicine and probes in luminescent resonance energy transfer (LRET) for bioassays, as well as reagents for diagnosis in magnetic resonance imaging (MRI). In this progress report, we will focus on recent progress on how rare earth amino complexes bind to DNA and change DNA structure, especially on DNA B-Z transition induced by rare earth amino acid complex and its potential impact on Alzheimer's disease (AD).     

韶冶电尘提镉系统产能提高的研究

文章通过对韶关冶炼厂电尘提镉系统中工艺、设备等方面存在的问题进行分析,找出了制约产能提高的瓶颈因素,结合生产实际提出了改进措施,在生产中实施后取得了良好的效果.     

某矿不同出矿点矿石性质差异对指标的影响

通过对某铅锌矿不同出矿点矿石及综合样(将各出矿点的矿样按一定比例配制而成)的试验研究,查明了各个出矿点矿石的选别特性,提出了综合样在现有现场流程下能够达到的选别指标,为更好地指导生产及评价生产指标提供了科学依据.     

Numerical Simulation on Inclusion and Bubble Entrapment in Solidified Shell in Model Experiment and in Mold of Continuous Caster With DC Magnetic Field

A model experiment investigating entrapment of inclusions and bubbles on the solidified shell was performed using molten steel,and the conditions for inclusion and bubble entrapment and mechanism of entrapment were studied.The results were applied to the flow behavior in the casting mold of a continuous caster.At the solid-liquid interface,entrapment of inclusions is greatly reduced by the existence of a low velocity flow,e.g.,0.05m/s.The above-mentioned interfacial flow velocity dependency of inclusion entrapment is considered to be largely influenced by changes in the thickness of the concentration boundary layer,which depend on the interfacial flow velocity.Specifically,bubbles and inclusions which enter the concentration boundary layer are drawn to the solid-liquid interface by a suction force which is several orders larger than the Saffman’s force.In addition to the above-mentioned suction force,the so-called cleaning effect is determined by fluid-dynamic forces such as drag force,etc.which act on particles,and furthermore,by resident time of particles at the solid-liquid interface,which depends on the solidification rate.In a FC mold with a 2-stage electromagnetic brake,flotation of bubbles entrained in the jet flow from the nozzle is accelerated with the large DC magnetic field.This is attributed to the braking effect of the DC field on the nozzle jet and the upward flow by the buoyancy of the bubbles.As a result,the interfacial flow velocity can be normalized by increasing the strength of the magnetic field,and entrapment of large bubbles and inclusions can be reduced.     

自攻螺钉用SWRCH18A冷镦盘条试制

文章介绍了在包钢现有技术装备条件下,试制SWRCH18A自攻螺钉用冷镦盘条的整个过程,给出了试制及用户使用结果,并结合实际情况探讨了开发具有冷加工性能要求的盘条所应具备的条件.