铁锰矿井废水处理中紫外光-芬顿试剂的应用效能研究

使用紫外光-芬顿试剂对铁锰矿井水进行处理。考察了pH值、H2O2投加量、反应温度、光照时间对紫外光-芬顿试剂处理铁锰矿井废水的影响。结果表明:紫外光-芬顿试剂对铁锰矿井水的处理有良好的处理效果,当pH值为5.5,H2O2的投加量为8mmol/L,反应温度30℃,光照时间为5min时候,Mn2+的去除效率可以达到93%。     

Fenton试剂和锰砂协同处理铁锰矿井废水的研究

以阜新市某矿区铁锰矿井水为对象,研究了Fenton试剂和锰砂协同处理铁锰矿井废水的机理与效率。结果表明:Fenton试剂和锰砂协同处理铁锰矿井废水有很好的效果,当H2O2的投加量为0.15 mg/L,pH为8,滤速为8 m/h时,Fenton试剂和锰砂联合作用比单独锰砂处理效率能提高30%左右,对锰的去除率最高可达到96%。     

Fenton氧化法深度处理制革废水生化出水试验研究

采用Fenton氧化法深度处理以制革废水为主的园区生化处理出水,试验表明:影响Fenton氧化的因素从大到小依次为H2O2投加量、Fe2+浓度、pH、反应时间。当进水CODCr平均为116.6mg/L时,在H2O2投加量50mmol/L、Fe2+投加量10mmol/L、pH为3、反应时间60min的最佳条件下,出水CODCr平均为31.7mg/L;在H2O2投加量25mmol/L、Fe2+投加量7.5mmol/L、pH为5、反应时间40min的经济运行条件下,出水CODCr平均为46.6mg/L。经济条件下的运行成本比最佳条件下的运行成本可节约2.3元/m3。     

Fenton试剂处理林可霉素废水的试验研究

采用Fenton试剂处理林可霉素废水,通过正交试验确定其主要影响因素的最佳水平组合为:FeSO4.7H2O投加量3.75 mmol(150 mL原水中),进水pH 4,H2O2/Fe2+为20∶1,反应时间30 min。在正交试验基础上,通过单因子分析确定了系统的最佳运行条件。在FeSO4.7H2O投加量为2.07 mmol(150 mL原水中)、进水pH为5、H2O2/Fe2+为10∶1、反应时间为90 min的条件下,CODCr去除率可达71%,处理出水BOD5/CODCr为0.44。     

Fenton试剂与TiO_2光催化氧化农药废水研究

以合肥市循环经济园区某农药厂的生产废水为研究对象,分别将Fenton高级氧化法和TiO2光催化氧化法应用于农药废水的预处理,研究了反应时间、pH值、H2O2投加量、TiO2投加量等对CODCr去除率的影响。结果表明:Fenton高级氧化法和TiO2光催化氧化法在处理农药废水方面都具有一定的效果;H2O2投加量是影响Fenton试剂氧化农药废水的主要因素,当初始pH值为4、反应时间为90 min、Fe2+的投加量为0.04 mol/L、H2O2投加量为0.4 mol/L时,Fenton高级氧化法的处理效果最好;在光催化氧化试验中,当初始pH值为9、反应时间为120 min、TiO2投加量为2.64 g/L时,TiO2光催化氧化效果最佳。     

Fenton高级氧化技术去除水中有机污染物2-MIB的影响因素研究

针对目前比较关注的致嗅物质污染问题,选用Fenton高级氧化技术研究了其对水中致嗅物质2-甲基异莰醇（2-MIB）的去除,探讨了Fenton反应对水中致嗅物质的去除效能及H2O2/Fenton摩尔比、Fe2＋浓度、反应时间和溶液pH值各因素对氧化反应的影响。提出了Fenton氧化反应去除2-MIB的最佳反应条件。实验结果表明：Fenton高级氧化能有效去除水中的2-MIB。在H2O2/Fenton摩尔比为3.0、Fe2＋浓度10 mg/L、反应时间10 min和溶液pH值为3.0时,去除效率达到97.9%。Fenton氧化反应的操作条件（浓度、pH值等）比较容易实现,因此Fenton氧化技术在实际污染处理中有很大的应用前景。     

Fenton试剂-石英砂工艺处理铁锰矿井废水

针对铁锰矿井废水中锰离子难去除的问题,本试验采用Fenton试剂-石英砂工艺研究了锰离子的去除效率与机理。结果表明:加入H2O2比不加入对锰离子的去除效果好,各因素的最佳值分别为:当H2O2投加量为0.15mg/L、滤速为8 m/h,pH为7,石英砂粒径为1.0 mm时,锰的最高去除率可达到90.7%。     

Fenton试剂处理香精香料废水的研究

采用Fenton试剂处理香精香料废水,试验探讨了不同pH、H2O2(30%)、FeSO4·7H2O用量和反应时间等因素对CODCr去除率的影响。结果表明,在pH为3、H2O2投加量为40mL/L、FeSO4·7H2O投加量为4g/L、反应时间为3h时,CODCr去除率为75%,色度去除率最高达到82%。Fenton试剂对香精香料生产废水的CODCr和色度都有较好处理效果。     

Fenton试剂处理选矿废水的试验研究

研究用Fenton试剂处理含苯胺黑药(二苯胺基二硫代磷酸)模拟废水和实际选矿废水,分别考查了反应初始pH值、Fe2+浓度及H2O2用量对COD去除率的影响。结果表明:氧化时间为10 min,反应初始pH值为4,ρ(Fe2+)=1.83 g/L,ρ(H2O2)=5.55 g/L,模拟废水苯胺黑药的质量浓度为300 mg/L时,COD去除率达到83.6%;对于实际废水,当ρ(Fe2+)=50mg/L,pH值=3.5,ρ(H2O2)=1800mg/L时,出水ρ(COD)从1000mg/L降到32 mg/L,COD去除率为96.8%,达到废水排放标准,药剂成本估计为每处理1 m3废水需要费用18元。     

Fenton接触氧化法强化石英砂—锰砂滤料处理铁锰矿井废水

为了解决目前常用的接触氧化法除铁除锰工艺中铁离子存在时锰离子难去除的问题,本文重点研究了Fenton接触氧化法强化石英砂-锰砂滤料的除铁除锰效率和机理。结果表明:Fenton试剂+锰砂+石英砂工艺除铁锰的效果很好,影响因素的最佳值如下:加入H2O2形成Fenton试剂后可以强化石英砂-锰砂工艺除铁除锰的效果,当H2O2投加量为0.15 mg/L、滤速为8 m/h、pH为7时,铁离子的去除率可达到92%,当H2O2投加量为0.17mg/L、滤速为8 m/h、pH为7时,锰离子的去除率可以达到97%。     

Effective degradation of para-chloronitrobenzene through a sequential treatment using zero-valent iron reduction and Fenton oxidation

In this study, zero-valent iron (ZVI) was used to pretreat para-chloronitrobenzene (p-CNB), and the major product was para-chloroaniline (p-CAN). By adding H(2)O(2) directly, further p-CAN degradation can be attributed to Fenton oxidation because ferrous ions (Fe(2+)) released during the ZVI corrosion could be used as an activator for H(2)O(2) decomposition. In the reduction process, the reduction efficiency of p-CNB as well as Fe(2+) concentration increased with increasing iron dosage and decreasing solution pH. Under the optimal conditions, 25 mg L(-1) of p-CNB could be transformed in 3 h when initial solution pH was 3.0 and ZVI dosage was 2.0 g L(-1). A sufficient amount of Fe(2+) (50.4 mg L(-1)) was obtained after the above reaction to activate H(2)O(2). In the Fenton process, the oxidization of p-CAN was also more effective in acidic conditions and it increased with increasing H(2)O(2) concentration. The control experiments showed that the sequential treatment was more effective than Fenton oxidation alone in treating p-CNB wastewater since the removal rate of total organic carbon (TOC) was improved by about 34%. It suggested that the amino function group is more susceptible to oxidative radical attack than the nitro function group. Therefore, sequential treatment using zero-valent iron reduction followed by Fenton oxidation is a promising method for p-CNB degradation.     

Fenton试剂在微波条件下处理稻壳热解发电含酚废水的试验

采取试验手段,研究在微波条件下用Fenton试剂处理含酚废水的效果,探讨H2O2质量浓度、FeSO4质量浓度、pH值、反应时间和微波功率等因素对稻壳热解发电废水中COD、挥发酚及色度去除率的影响,并进行不同条件下Fenton反应的对比试验。结果表明,在微波条件下,Fenton试剂能快速降解含酚废水,处理后水样的COD去除率超过73%,挥发酚去除率超过99%,色度去除率接近50%。该含酚废水的最佳处理条件是:H2O2质量浓度为1500 mg/L,FeSO4质量浓度为100 mg/L,pH值为3,反应时间为10 min,微波功率为400 W。     

Enhanced degradation of paracetamol by UV-C supported photo-Fenton process over Fenton oxidation

For the treatment of paracetamol in water, the UV-C Fenton oxidation process and classic Fenton oxidation have been found to be the most effective. Paracetamol reduction and chemical oxygen demand (COD) removal are measured as the objective functions to be maximized. The experimental conditions of the degradation of paracetamol are optimized by the Fenton process. Influent pH 3, initial H(2)O(2) dosage 60 mg/L, [H(2)O(2)]/[Fe(2+)] ratio 60 : 1 are the optimum conditions observed for 20 mg/L initial paracetamol concentration. At the optimum conditions, for 20 mg/L of initial paracetamol concentration, 82% paracetamol reduction and 68% COD removal by Fenton oxidation, and 91% paracetamol reduction and 82% COD removal by UV-C Fenton process are observed in a 120 min reaction time. By HPLC analysis, 100% removal of paracetamol is observed at the above optimum conditions for the Fenton process in 240 min and for the UV-C photo-Fenton process in 120 min. The methods are effective and they may be used in the paracetamol industry.     

二氧化氯催化氧化降解铬黑T试验研究

在常温常压下,对Fe2O3/γ—A12O3+H2O2和ClO2+TiO2两种催化氧化体系处理铬黑T废水的效果进行了分析。试验结果表明,处理甲基橙废水效果较好的Fe2O3/γ—Al2O3+H2O2组合对铬黑T的降解效果非常有限,而ClO2+TiO2组合的处理效果较好:以500 mg/L的铬黑T溶液为模拟废水,当pH为4,C102投加量为200 mg/L,TiO2投加量为500 mg/L,反应时间为90 min时,脱色率达89.96%,CODCr的去除率可达45.36%。     

Phosphorus removal from synthetic and municipal wastewater using spent alum sludge.

In the present study, phosphorus removal was studied using as coagulant spent alum sludge from a water treatment plant of EYDAP (Athens Water Supply and Sewerage Company) and compared to alum (Al2(SO4)3.18H2O), iron chloride (FeCl3.7H2O), iron sulfate (Fe2(S04).10H2O) and calcium hydroxide (Ca(OH)2) at a constant pH (equal to 6).The comparison was based on their efficiency to remove phosphorus in synthetic wastewater consisting of 10 mg/L P as potassium dihydrogen phosphate and 50 mg/L N as ammonium chloride, The experiments were carried out using a jar-test apparatus and the measurements were performed according to the Standard Methods for the Examination of Water and Wastewater. Pure alum, iron chloride and iron sulfate were much more efficient in phosphorus removal than the spent alum sludge but in the case of calcium hydroxide, phosphorus removal was very low in pH = 6. Specifically, orthophosphate were totally removed by alum using 15 mg/L as Al, by alum sludge using 75 mg/L as Al and by FeCl3.7H2O or Fe2(SO4).10H2O using 30 mg/L of Fe while in the case of calcium hydroxide P removal was actually zero. pH measurements showed that the uptake of phosphates is associated to the release of OH ions in the solution and that the end of P uptake is accompanied by the stabilization of pH. Finally this spent alum sludge was tested on municipal wastewater and proved to be effective as apart from phosphorus it was shown to remove turbidity and COD.     

Multiple responses analysis and modeling of Fenton process for treatment of high strength landfill leachate

Landfill leachate is one of the most recalcitrant wastes for biotreatment and can be considered a potential source of contamination to surface and groundwater ecosystems. In the present study, Fenton oxidation was employed for degradation of stabilized landfill leachate. Response surface methodology was applied to analyze, model and optimize the process parameters, i.e. pH and reaction time as well as the initial concentrations of hydrogen peroxide and ferrous ion. Analysis of variance showed that good coefficients of determination were obtained (R2 > 0.99), thus ensuring satisfactory agreement of the second-order regression model with the experimental data. The results indicated that, pH and its quadratic effects were the main factors influencing Fenton oxidation. Furthermore, antagonistic effects between pH and other variables were observed. The optimum H2O2 concentration, Fe(II) concentration, pH and reaction time were 0.033 mol/L, 0.011 mol/L, 3 and 145 min, respectively, with 58.3% COD, 79.0% color and 82.1% iron removals.