聚烯烃表面氧化处理的研究

研究了以高锰酸钾或重铬酸钾／水／浓硫酸＝５∶８∶１００（质量比）或２０％（质量分数）的过硫酸铵水溶液及氯化铁或硫酸铜作为催化剂对聚烯烃进行的表面氧化处理,并通过熔点和红外光谱及光电子能谱等方法对氧化反应和产品的结构进行了表征。研究表明,最佳氧化温度和时间分别为４５℃～６０℃与４５ｍｉｎ;用ＫＭｎＯ４／Ｈ２ＳＯ４／ＦｅＣｌ３／ＣｕＳＯ４,Ｋ２Ｃｒ２Ｏ７／Ｈ２ＳＯ４／ＦｅＣｌ３,Ｋ２Ｃｒ２Ｏ７／Ｈ２ＳＯ４／ＣｕＳＯ４体系对聚乙烯的氧化中,氧化深度依次减小,Ｃ原子的摩尔分数由未氧化时的８０．８０４％,分别降低为３１．９０７％、６９．９０５％和７８．６６９％;在ＦｅＣｌ３催化下,产品中Ｃｌ的含量普遍增加,而以ＫＭｎＯ４／Ｈ２ＳＯ４／ＦｅＣｌ３／ＣｕＳＯ４氧化时增加最多,但对Ｋ２Ｃｒ２Ｏ７／Ｈ２ＳＯ４／ＦｅＣｌ３氧化体系,Ｏ含量的增加相对较多     

乙酸异丁酯合成中无机盐催化作用初探

研究了ＣｕＳＯ４．５Ｈ２Ｏ２、ＣｕＳＯ４、ＦｅＳＯ４、７Ｈ２Ｏ、ＦｅＣｌ３、６Ｈ２Ｏ、ＣｕＣｌ２．２Ｈ２Ｏ等５种盐对异丁醇与乙酸酯化反应的催化性能，结果表明ＦｅＣｌ３．６Ｈ２Ｏ和ＣｕＣｌ２．２Ｈ２Ｏ是较好的催化剂，酯转化率达８６－９３％。     

硫酸镍结晶母液的渗析净化

本文应用Ｓ２０３膜对含Ｈ２ＳＯ４〉５５０ｇ／Ｌ的硫酸镍结晶母液进行渗析净化的工业性试验。结果表明：渗析工艺能满足现行铜电解生产工艺流程对净化效果的要求，回收酸与Ｃｕ＾２＋、Ｆｅ＾３＋Ｎｉ＾２＋、Ｂｉ＾３＋等离子能有效分离，当水／酸值取０．９－１．１，单位处理能力≯５０Ｌ／ｍ＾２．ｄ时，回收酸浓度〉２７４ｇ／Ｌ；残液酸浓度〈２８０ｇ／Ｌ，阳离子截留率〉９０％。     

四羰基钴钠的合成及红外光谱研究

在常温常压下，用Ｎａ２Ｓ２Ｏ３／Ｆｅ－Ｍｎ粉为联合活化剂，将一氧化碳通入ＣｏＣｌ２／ＣＨ３ＯＨ溶液，制备了Ｎａ［Ｃｏ－（ＣＯ）４］，３ｈ后转化率可达９０％以上。选择性接近１００％。ＩＲ分析发现产物溶液在１９０４ｃｍ－１左右有一强的特征吸收峰，证实了［Ｃｏ（ＣＯ）４］－离子的存在。研究了反应条件对产率的影响，讨论了合成羰基钴钠的反应机理。     

Mo（Ⅵ）与Tiron的显色反应及应用研究

研究了Ｍｏ（Ⅵ）与Ｔｉｒｏｎ的反应，发现在ｐＨ４．０的ＨＡｃ－ＮａＡｃ介质中形成１：１配合物，该配合物在２５２ｎｍ、３１５ｎｍ有两个吸收峰，而在可见光区无吸收峰。测得ε２５２＝６．９×１０￣３Ｌ·ｍｏｌ－１·Ｃｍ－１，ε３１５＝３．５×１０３Ｌ·ｍｏｌ－１·Ｃｍ－１。据此建立了测定Ｍｏ（Ⅵ）的方法，在２５２ｎｍ和３１５ｎｍ处的线性范围分别为１．６×１０－６ｍｏｌ·Ｌ－１～２．Ｏ×１０－４ｍｏｌ·Ｌ－１和３．２×１０－４ｍｏｌ·Ｌ－１～２．０×１０－４ｍｏｌ·Ｌ－１。检出限分别为８．Ｏ×１０－７ｍｏｌ·Ｌ－１和１．６×１０－６ｍｏｌ·Ｌ－１．ＰＯ＿４￣３＋、ＳｉＯ＿３￣２－对测定无干扰，而Ｗ（Ⅵ）、Ｖ（Ⅴ）、Ｆｅ（Ⅲ）等有干扰。该法试用于有机磷合钼聚多酸盐样品的测定，结果满意，方法回收率９６％～１０２％，变异系数≤１．ｌ％（ｎ＝１２）。     

聚（2,5—二甲基）对苯硫醚合成的初步研究

介绍以硫磺、氯和对二甲苯为原料,无水三氯化铁（ＦｅＣｌ３）作催化剂,三氯甲烷（ＣＨ３Ｃｌ３）作溶剂,合成聚（２,５－二甲基）对苯硫醚（ＤＭＰＰＳ）。最佳反应条件为：最佳投料摩尔比：对二甲苯／ＳＣｌ２／ＦｅＣｌ３＝１．０／１．０２／０．１０,反应温度２０～８０℃,反应时间５～６ｈ。收率为６２．５％。产品经红外光谱、Ｘ射线衍射光谱、激光拉曼光谱和差热分析验证,为线型结晶性,无双硫键,熔点Ｔｍ为３０６℃（美国ＲｙｔｏｎＶ－１型ＰＰＳ熔点为２７５～２８５℃的工程高聚物。所述合成方法原料和催化剂价廉易得、合成工艺简化、无副产物ＮａＣｌ产生、操作易、周期短、成本比ＰＰＳ低。其不足之处是产品收率不够高,有待在溶剂和催化剂选择方面作进一步研究。     

金—钼酸盐—丁基罗丹明B体系显色反应研究

研究了在高氯酸和聚乙烯醇（ＰＶＡ）存在下，金与钼酸盐和丁基罗丹明Ｂ（ＢＲＢ）的显色反应。其适宜条件ＣＨＣｌＯ４＝１．５ｍｏｌ／Ｌ，ＣＭｏＯ２－４＝９．１×１０－４ｍｏｌ／Ｌ，ＣＢＲＢ＝３．８×１０－５ｍｏｌ／Ｌ及０．０８％ＰＶＡ。金钼杂多酸—丁基罗丹明Ｂ离子缔合物的最大吸收位于５７０ｎｍ，表观摩尔吸光系数为３．３６×１０６Ｌ·ｍｏｌ－１·ｃｍ－１，金量在０～４０μｇ／Ｌ范围内服从比尔定律，测定极限（Ｓ／Ｎ＝３）０．９０μｇ／Ｌ（ｎ＝１０），对于２８μｇＡｕ（Ⅲ）／Ｌ测定的相对标准偏差２．１％（ｎ＝７）。缔合物至少可稳定５ｈ，摩尔比Ａｕ∶ＢＲＢ＝１∶３。考察了４４种共存离子的影响，大多数常见离子不干扰，用活性炭分离富集金，对砂矿和炭粉中金的测定，结果满意。     

福美双分光光度法快速测定微量铜

在碱性条件下, Ｃｕ ? 与福美双（ Ｎ Ｃ Ｈ３ Ｃ Ｈ３ Ｃ Ｓ Ｓ Ｓ Ｃ Ｓ Ｃ Ｈ３ Ｃ Ｈ３ ） 形成稳定的桔红色配合物,配合物的λｍ ａｘ ＝ ４５２ ｎ ｍ , 表观摩尔吸光系数ε＝ １ ．２ ×１０ ４ 。铜含量在０ ～１０ μｇ／ ｍ Ｌ 范围内符合比耳定律。     

耐磨Ni－SiC复合电镀及其应用

含ＳｉＣ最高达１１％的Ｎｉ－ＳｉＣ复合镀层的镀液配方及操作条件为：Ｎｉ（ＳＯ_３．ＮＨ_２）_２·４Ｈ_２Ｏ４１０，ＮｉＣｌ_２·６Ｈ_２Ｏ１０，Ｈ_３ＢＯ_３５０，ＯＰ－１００．４及ＳｉＣ（３μｍ）２０－１２０ｇ／Ｌ，ｐＨ４，５５±２℃，５Ａ／ｄｍ￣２，需搅拌．     

镍铁合金镀液故障处理

镍铁合金镀液故障处理郭绍湘（山东红旗机械厂，２６１０３１）１简介双层镍铁合金／装饰铬生产线，Ｎｉ－Ｆｅ槽液成份及工艺规范如下：ＮｉＳＯ４·７Ｈ２Ｏ３００～３５０ｇ／Ｌ，Ｈ３ＢＯ３４０～４５ｇ／Ｌ，ＮａＣｌ１５～１８ｇ／Ｌ，Ｆｅ总１～２．５ｇ／Ｌ，Ｎａ...     

骑式摩托车油箱喷涂工艺的改进

面对日益激烈的市场竞争,摩托车油箱外观质量越来越成为影响销售的因素之一。文章介绍了改进工艺后的油箱涂装,该涂装体系提高了油箱外观的丰满度,降低了油箱涂装的生产成本。     

茶多酚提取方法进展

本文综述了国内外现有茶多酚提取方法的现状以及近期的研究进展，并对其优缺点进行了评价。这将有助于中低档茶的综合利用和茶多酚的进一步开发应用。     

氢气纯度分析方法准确性的探讨

ONACCURACYOFANALYSISOFOFHYDROGEN1前言我公司目前应用的氢气纯度分析方法有两种,一种是爆炸反应法,另一种是焦性没食子酸吸收法。几年来,人们对两种分析方法的准确性曾有过褒贬不一的评论。这里我们也谈谈自己粗浅的观点。2爆炸法测定氢气纯度一定量的氢气样品与适量的空气之均匀混合物因反应后生成液体水而引起气体体积减少,减少的体积等于参加反应气体体积之和。其中l／3为氧气,2／3为氢气。根据氢气取样量和反应前后混气体体积之差,以及氢气在反应中的体积比例关系,可计算出样品的氢气纯度。计算公式式中：A一混…     

COMPARISON OF METHODS OF ANALYSIS OF GYPSUM1

The different analytical methods proposed for the evaluation of gypsum have been subjected to an experimental test. A combination method, consisting of a fusion with KHCO₃ and determination of CaO by KMnO₄ titration, the SO₃ by Andrews method of titration of BaCrO₄ has been found to give very reliable results with the least consumption of time.     

HEASUREHENT OF INSTANTANEOUS RATES OF LOSS OF VOIATILE COMPOUNDS DURING DRYING OF DROPS

A novel technique serves to monitor instantaneous rates of loss of a volatile solute from a suspended drop during drying. A highly sensitive electron capture detector is used to monitor concentrations of SF6 released into a flowing gas stream from a suspended, drying drop. Simultaneously, the appearance and morphological development of the drop are monitored with a video camera. This provides the wherewithal of relating instantaneous rates of loss of the volatile solute to particular events during the development of particle morphology.

Initial experiments have been carried out with drops of aqueous solutions of glucose, sucrose, maltodextrin and coffee extract. The results clearly display the onset of the volatiles-retentive selective diffusion phenomenon. There is also substantial loss of the volatile component later in the drying process, when the drops undergo repeated ex ansion, bursting and cratering due to the formation of internaf bubbles. These experiments appear to be the first quantitative demonstration of major losses accompanying changes in drop morphology.     

用两个形状指数表征粉煤灰颗粒形貌的研究

引用两个形状指数表征颗粒形状的概念,即先将颗粒形状近似为椭圆,再将椭圆图像分离:以圆为基准的颗粒宏观形状指数δ;以光滑椭圆为基准的颗粒轮廓凹凸度,即微观形状指数ζ。分析和发展了近似椭圆模型。并运用图像分析仪对粉煤灰、水泥样品进行实验。结果表明,粉煤灰颗粒的两个形状指数δ和ζ都大于水泥颗粒。证明粉煤灰颗粒的球形度、表面光滑度优于水泥,而且,随着粒径增大,δ和ζ呈下降趋势,表明磨制颗粒越粗。(?)粒形状越不规则。文中还运用近似椭圆模型再现了颗粒的模拟图像。     

典型煤碳燃烧特性研究和数值模拟

本文以三种典型煤的碳燃烧为研究对象，分别采用简单一维沉降燃烧方式和等温加热燃烧方式，实验研究了煤在快速加热条件下，其碳的初期和中，后期燃烧过程。以实验为基础，建立了煤的碳燃烧模型，变工况数值模拟了煤的碳燃烧过程，揭示了煤不同条件下的单颗粒碳燃烧特性。     

剪力对梁变形影响的分析

本文用材料力学的分析方法,导出了一个计入剪力时梁的挠曲线的微分方程式。为了估计剪力对梁变形的影响,在集中力作用下梁内剪力用一个单值连续的反三角函数表示。由能量法确定了截面因子数值之后,定量地给出计入剪力时梁变形的分析结果。其结果和弹性力学的结来是一致的。     

酚醛树脂热降解动力学研究

用热失重非等温法对不同甲醛,苯酚魔鬼洋比的酚树脂进行了热降解动力学研究。结果表明,甲醛,苯酚摩尔比为１．５时,酚醛树旨的热发活化能最高。耐热性最好。     

ANALYSIS OF RECENT MEASUREMENTS OF THE VISCOSITY OF GLASSES

Viscosity of Simple Soda-Silicate 500° to 1400°C Comparison of the results given by English with those of Washburn, Shelton and Libman, indicates a discrepancy in the absolute values of log₁₀ viscosity amounting to 0.6, those of Washburn et al., being relatively too high. If correction for this is made, the isothermal curves of log₁₀ viscosity as a function of soda content are smooth up to 50% Na₂O, showing no inflection. The observations as a function of temperature T are all represented within accidental error by an equation of the type where all three constants vary regularly with the composition. Change of Viscosity of Glass (6SiO₂, 2Na₂O) due to Molecular Substitution of CaO, MgO and Al₂O₃ for Na₂O The effect is clearly brought out by plotting (from the results of English) the change of log₁₀η due to the substitution as a function of temperature. The curves each show a sharp bend at a temperature between 840° and 1050°C, which is designated the aggregation temperature T_a. If we divide these curves by the corresponding percentage substituted, we get curves for each oxide which are straight and parallel below the aggregation temperatures, the slopes (increase of change of log₁₀η per 100°C) being −0.056 (CaO), −0.055 (MgO), −0.018 (A1₂O₃) per per cent oxide substituted. For substitution of 1/2 molecule the slopes are −0.325 (CaO), −0.23 (MgO) and −0.18 (Al₂O₃) per 100°. At the aggregation temperature the change of log₁₀η per per cent is a minimum, 0.03 to 0.06 for CaO, 0.12 for MgO, 0.07 for Al₂O₃. Evidence of Aggregation in Glasses, from viscosity Measurements The sharp bends in the plots of change of log₁₀η due to substitution of an oxide for Na₂O, suggest the beginning of molecular aggregation at these temperatures. These aggregation temperatures are close to the devitrification temperatures, but the effect on the viscosity curves cannot be due to actual devitrification since it does not change with time. Taking the aggregation temperatures as equal to devitrification temperatures, additional isotherms are roughly sketched into the equilibrium triangle of the system Na₂O-CaO-SiO₂. Change of Viscosity of Glass (4SiO₂, 2Na₂O) due to of Substitution of B₂O₃ for SiO₂ The change of log₁₀η (from the results of English) is plotted as a function of temperature, and also the change of log₁₀η per per cent B₂O₃. The curves are more complex than for the substitution for Na₂O.