Microstructure and microwave dielectric properties of CaO-B2O3-SiO2 glass ceramics with various B2O3 contents

The effects of B2O3 addition on both the sintering behavior and microwave dielectric properties of CaO-B2O3-SiO2 (CBS) glass ceramics were investigated by Fourier transform infrared spectroscopy (FTIR),X-ray diffractometry (XRD) and scanning electron microscopy (SEM).The results show that the increasing amount of B2O3 causes the increase of the contents of [BO3],[BO4] and [SiO4],which deduces the increase of CaB2O4 and α-SiO2 and the decrease of CaSiO3 correspondingly.No new phase is observed throughout the...     

Low-temperature sintering and microwave dielectric properties of Li2MgTi3O8 ceramics doped with BaCu（B2O5）

The influences of BaCu(B₂O₅) (BCB) addition on sintering, microstructure and microwave dielectric properties of Li₂MgTi₃O₈ ceramics were investigated using X-ray diffractometry, scanning electron microscopy and microwave dielectric measurements. The experimental results show that a small amount of BaCu(B₂O₅) addition can effectively reduce the sintering temperature to 900 °C, and induce only a limited degradation of the microwave dielectric properties. Typically, the best microwave dielectric properties of ɛ _r=24.5, Q×f =24 622 GHz, τ _f=4.2×10⁻⁶ °C⁻¹ are obtained for 1.0% BCB-doped Li₂MgTi₃O₈ ceramics sintered at 900 °C for 3 h. The BCB-doped Li₂MgTi₃O₈ ceramics can be compatible with Ag electrode, which may be a strong candidate for low temperature co-fired ceramics applications.     

Effect of ZnO-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glass addition on the microwave dielectric properties of BaO-Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The effect of ZnO-B₂O₃(ZB) glass addition on the sintering behavior, microstructures and microwave dielectric properties of BaO-Nd₂O₃-TiO₂-Bi₂O₃ (BNTB) system was investigated with the aid of X-ray diffraction, scanning electron microscopy and capacitance meter. It is found that the ZB glass addition, acting as a sintering aid, can effectively lower the sintering temperature of BNTB system to 850 °C. The dielectric constant of BNTB-ZB ceramics increases with the increase of soaking time and the value of dielectric loss decreased with increasing soak time. The optical dielectric properties at 1 GHz of ɛ=74, tan δ=4×10⁻⁴, and TCC=25 ppm/°c were obtained for the BNTB system doped with 25 wt% ZB glass sintered at 850 °C for 2 h, representing that the BNTB-ZB ceramics could be promising for multilayer low temperature co-fired ceramics applications.     

Preparation and properties of crystallizable Glass/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composites for LTCC material

The investigated low temperature Co fired ceramics(LTCC) composite of 60wt% CaO-Al2O3-B2O3-SiO2 glass and 40wt% α-Al2O3 as a filler is a non-reactive system, which is a critical part of the low temperature Co fired ceramics process. Through a study on densification process, the phase transformation and microstructure can be revealed. Its composites typically consist of CaO-Al2O3-B2O3-SiO2 glass and α-Al2O3 powders of average particle size (D50=3.49 mm). The sintering behavior, phase evaluation, sintered morphology, and microwave dielectric properties were investigated. In the fire range of 800 to 900 ℃, the composites were crystallized after completion of densification. It is found that the composites start to densify at 825 ℃, simultaneously, the dielectric constant (εr) reaches its maximum. With increasing heat-treatment temperatures, due to the loose microstructure of the material, tanδ increases slightly. The last of the sintered samples were identified as partly Anorthite at 850 ℃. At that temperature it has εr of 7.9 and tanδ less than 1×10-3, and can be used as a promising LTCC material.     

The Effect of Bi2O3 on the Structure and Microwave Dielectric Properties of Ba6-3xNd8＋2xTi18O54 System（x=2/3）

The structures and dielectric properties of Ba6-3xNd8＋2xTi18O54 system（x=2/3） doped with different contents of Bi2O3, whose final molecular formula is Ba6-3x（Nd1-yBiy）8＋2xTi18O54 were investigated. It is indicated that the dielectric constant increases greatly whereas Q value（f0=4 GHz） decreases with the increase of Bi2O3 content. However, the temperature coefficient could be controlled below 0±30×10^-6/℃ in the experiment. These phenomena are related to the appearance of a new phase, Bi4Ti3O12, which has high dielectric constant. Also, that Bi^3＋（0.13 nm） substitutes for Nd^3＋（0.099 5 nm） will increase the unit cell volume, which will lead to the enlargement of the octahedron B site occupied by Ti^4＋. So the spontaneous polarization of Ti^4＋ ions will be strengthened. Besides, Bi^3＋ will fill up some vacancies which Ba^2＋ or Nd^3＋ ions leave in two A1 sites and four A2 sites. More positive ions polarize, which also contributes to higher dielectric constant. The samples got with the optimium properties are sintered at 1 200 ℃ for 4 h, when y=0.25, ε≈110, Q≈5 400（f0=4 GHz）, TCC=-4.7×10^-6/℃; When y=0.3, ε≈120, Q≈5 000（f0=4 GHz）, TCC=-24×10^-6/℃.     

Effects of nucleating additives on crystallization and properties of CaO-B2O3-SiO2 glass-ceramics

ZrO₂, TiO₂ and P₂O₅ were doped in CaO-B₂O₃-SiO₂ glass-ceramics as nucleating additives. Effects of different nucleating additives on the phase separation and crystalline behaviors were investigated by using gradient temperature furnace, DTA and XRD. Then, sintering process of the glass-ceramics was investigated by testing sintering shrinkage, dielectric constant and loss. The experimental results shows that the glass-ceramics doped with nucleating additives represents higher crystallization, with ZrO₂ as an exceptional effective dopant to promote the precipitation of wollastonite crystal. Finally, ZrO₂ containing glass-ceramics was chosen to study the influence of sintering temperature and soaking time with the help of X-ray diffraction analysis and density measurement. The glass-ceramics can be well consolidated at 850 °C for 10 min, with low dielectric constant (5.87) and loss (3.21 × 10⁻⁴), which is desirable for LTCC application.     

Thermoelectric properties of Ca3Co4O9 ceramics

Ca₃Co₄O₉ ceramics were prepared using the sol-gel process with ordinary pressing sintering and their thermoelectric properties were measured from room temperature to 673 K. The experimental results show that single phase Ca₃Co₄O₉ can be fabricated at 750–900 °C in different citrate acid molar proportions for 0.2–1.0. For all the oxides, both the Seebeck coefficients S and the electrical conductivities κ increase with the increasing temperature. The Seebeck coefficients S are all positive. The thermal conductivities k increase with the increasing temperature also and the lattice thermal conductivity κ _l plays an important role to the thermal conductivity κ. The citrate acid molar proportions have a large influence on the particle sizes, which influences the thermoelectric properties of the ceramics. The figure of merit increases with the increasing temperature and reaches 4.5×10⁻⁵ K⁻¹ at 573 K for the sample in the citrate acid molar proportion of 0.46.     

Low-temperature sintering and microwave dielectric properties of Ba<Subscript>2</Subscript>Ti<Subscript>3</Subscript>Nb<Subscript>4</Subscript>O<Subscript>18</Subscript> ceramics

The effects of CuO and H3BO3 additions on the low-temperature sintering,microstructure,and microwave dielectric properties of Ba2Ti3Nb4O18 ceramics were investigated.The addition of less amount of CuO (< 1 wt%) considerably facilitated the densification of Ba2Ti3Nb4O18 ceramics.Appropriate addition of H3BO3 (< 3.5 wt%) remarkably improved the microwave dielectric properties of ceramics.The addition of H3BO3 and CuO successfully reduced the sintering temperature of Ba2Ti3Nb4O18 ceramics from 1300 to 1050 ℃.B...     

Effect of sintering aid CuO-MnO2 on dielectric properties of 0.5Ba(Mg1/3Nb2/3)O3-0.5Ba(Ni1/3Nb2/3)O3 ceramics

Microstructures and microwave dielectric properties of 0.5Ba(Mg_1/3Nb_2/3)O₃-0.5Ba(Ni_1/3Nb_2/3)O₃ ceramics with x wt% CuO−x wt% MnO₂ additions (x=0.25–1) prepared by conventional solid-state route were investigated. It is found that low level-doping of CuO-MnO₂ can significantly improve the density of the specimens and their microwave dielectric properties. The relative density of 0.5Ba(Mg_1/3Nb_2/3)O₃-0.5Ba(Ni_1/3Nb_2/3)O₃ ceramics can be increased by 95% sintering at 1 330 °C due to the liquid phase effect. The second phase is not observed in ceramics with CuO-MnO₂ addition. The parameter ε _r increases with increasing sintering temperature, and Q _f is effectively promoted by CuO-MnO₂ addition. Higher CuO-MnO₂ content would make τ_f value more positive. Meanwhile, ε _r value of 30.5, Q _f value of 63 200 GHz and τ _f value of 0.5 ppm/°C were obtained for 0.5Ba(Mg_1/3Nb_2/3)O₃-0.5Ba(Ni_1/3Nb_2/3)O₃ ceramics with 0.5 wt% CuO-0.5 wt% MnO₂ addition sintered at 1 330 °C for 4 h.     

Effect of nucleating agent on the crystallization of tailings glass ceramics prepared by one-time sintering

Glass ceramics was made by the one-time sintering method using the main raw material of iron tailings. On the basis of quaternary system of CaO-MgO-Al₂O₃-SiO₂, using DTA, XRD and SEM, the effects of different nucleating agents and mixing amounts as well as heat treatment on the crystallization of tailings glass ceramics were studied. The experimental results show that, nucleating agent and heat treatment are two necessary conditions for one-time sintering preparation of tailings glass ceramics namely, only adding nucleating agent or experiencing heat treatment, the quaternary system can not crystallize. The composite nucleating agent consisting of Cr₂O₃ and TiO₂ can further lead to the crystallization of the CaO-MgO-Al₂O₃-SiO₂ quaternary system at the lower temperature, with the major phase of diopside. In the range of mass content, 0%–4%, crystal intensity and crystal content grow. But when mass content is more than 4%, the crystal size will become coarser and the crystal distribution will be less regular. Different heat treatment regimes do not change the composition of the crystalline major phase in the glass ceramics crystallization of CaO-MgO-Al₂O₃-SiO₂ system. In the range of 30–60 minutes, with the extension of nucleation and crystallization, crystallization degree enhanced, but if the holding time surpasses 60 minutes, the crystallization is worse. Funded by The National Key Technology R & D Program of China for the 11^th Five-Year Plan(2006BAJ04A04)     

Effect of Rare Earth Oxides on the Microstructure and Microwave Dielectric Properties of CaO-MgO-Nb2Os-TiO2 System Ceramics

La2O3 and SrO-doped CaO-MgO-Nb2O3-TiO2 system ceramics were prepared by solid-state ceramic technique.The microstructure and microwave dielectric properties of CaO-MgO-Nb2O5-TiO2-La2O3 cermics can be adjusted by varying the amount of La^3＋ or Sr^2＋ ions respectively.The replacement of Ca^2＋ by La^3＋ at A-site of the ceramics increases the quality factor Q value（ at 7.6GHz）as well as the temperature coefficient of resonant frequency τf and decreases the dielectric constant εr and the substitution of Sr^2＋ at A-site in this ceramics system exhibits opposite characteristics.The microwave properties of La^3＋,Sr^2＋-doped CaO-MgO-Nb2O5-TiO2 system ceramics depend on the degree of octahedral distortion inside materials.     

Effects of heat treatment temperature on crystallization and thermal expansion coefficient of Li2O-Al2O3-SiO2

The basic glass of Li₂O-Al₂O₃-SiO₂ system using P₂O₅ as nucleator was prepared by means of conventional melt quenching technology, and the heat-treatment process was determined by using differential thermal analysis. The crystalline phases and the microstructure of the glass-ceramics were investigated by using X-ray diffraction and scanning electron microscopy. The results show that the glass based on Li₂O-Al₂O₃-SiO₂ oxides using P₂O₅ as nucleator can be prepared at lower melt temperature of 1450°C and the glass-ceramics with lower thermal expansion coefficient of 21.6 × 10⁻⁷°C⁻¹ can also be obtained at 750°C. The glass-ceramics contain a few crystal phases in which the main crystal phase is β-quartz solid solution and the second crystal phase is β-spodumene solid solution. When the heat treatment temperature is not higher than 650°C, the transparent glass-ceramics containing β-quartz solid solution can be prepared. β-quartz solid solution changes into β-spodumene solid solution at about 750°C. And the appearance of the glass-ceramics changes from translucent, part opaque to complete opaque with increasing temperature.     

Dielectric Properties of Ag（Nb1-xTax）O3 and Bi2O3 Doped Ag（Nb1-xTax）O3 Ceramics

Dielectric properties of Ag（Nb1-xTa）O3 and Bi2O3 doped Ag（Nb1-xTax）O3 solid solutions were investigated. The results show that with the increase of Ta content （x）, the sintering temperature increased, and the dielectric loss （tanδ） and the temperature coefficient （αc） decreased. Ag（Nb1-xa）O3 （x=0.4） ceramics sintered at 1 100℃ had the highest permittivity （516.8） and a lower tanδ （0.0021） at 1 MHz, and its temperature coefficient was about 191 ppm/℃. The sintering temperature of Ag（Nb1-xTa）O3 （x=0.4） was lowered by the addition of Bi2O3, and its dielectric properties were improved. Ag（Nb0.6Ta0.4）O3 ceramics with 2.5 wt% Bi203 addition presented the optimum dielectric properties （ε=566, tanδ= 0.0007 and αc≈0ppm/℃） （1 MHz）,     

Structure and dielectric properties of ZnO and Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> doped BaO-TiO<Subscript>2</Subscript> system microwave ceramics

The microwave dielectric properties and microstructure of BaTi4.3ZnyO9.6＋y ＋0.02 mol% SnO2＋0.01 mol% MnCO3＋x mol% Nb2O5（x=0-0.05, y=0-0.08） system ceramics were studied as a function of the amount of ZnO and Nb2O5 doped. Addition of （y=0-0.05） ZnO and （x=0-0.025） Nb2O5 enhanced the reactivity and decreased the sintering temperature effectively. It also increased the dielectric constant ε r and quality factor Q（=1/tan 8） of the system due to the substitution of Ti^4＋ ions with incorporating Zn^2＋and Nb^5＋ ions, which was analyzed by the reaction ZnO＋Nb2O5＋ 3 TiTxTi →ZnTi＋ 2NbTi＋3TiO2. When the system doped with （y=0.05） ZnO and （x=0.025） Nb205 were sintered at 1 160 ℃ for 6 h, the εr. Qf0 value and rfwere 36.5, 42 000 GHz, and＋1.8 ppm/℃, respectively, at 5 GHz.     

Luminescent properties of BaO-La2O3-B2O3 glasses with dopant

The luminescent properties of glasses synthesized in air atmosphere by conventional high temperature process were stud{ed. The emissions spectra of Eu^2 and Eu^3 were observed in BaO-La2O3-B2O3-Eu2O3 glasses.The results show that the broad emission peaks at 430 nm correspond to 5d→4f emission transition of Eu^2 , the sharp emission peaks at 592, 616, 650 and 250 nm correspond to 5^D0→1Fj(j=1--4) emission transition of Eu^3 ,respectively, which indicates that the BaO-La2O3a-B2O3-Eu2O3 glass can convert ultraviolet and green omponents of sunlight into blue and red light so as to increase the intensity of blue and red light, respectively. The luminescent in--tensity of Eu^2 increases with increasing the molar ratio of Tb^3 in BaO-La2O3-B2O3-Eu2O3a-Tb4O3 glasses, whereas the luminescent intensity of Eua^3 decreases. So the luminescent intensity of Eu(Ⅲ,Ⅱ) is influenced by Tb^3 .These phenomena can be explained by electron transfer mechanism; Eu^3 (4f6) Tb^3 (4f^8)→Eu^2 (4f′) Tb^4 (4f′). Taking advantage of the luminescent properties of BaO-La2O3-B2O3-Eu2O3 glasses, light-conversion glass for agriculture can be produced.     

Phase structure and electrical properties of La<Subscript>2</Subscript>O<Subscript>3</Subscript>-doped BiInO<Subscript>3</Subscript>-PbTiO<Subscript>3</Subscript> ceramics with high curie temperature

The phase structure and electrical properties of pure and La2O3-doped Bi-InO3-PbTiO3 （BI-PT） ceramics were studied respectively. In （1 -x）BI-xPT （x=0.72-0.80） ceramics, the stability of tetragonal phase increased with increasing x, and pure perovskite structure was obtained for x=-0.80 ceramics. The phase transition temperature range was between 575 ℃ and 600 ℃ for x=0.72-0.80 ceramics, higher than that of PT （-490 ℃）. The c/a ratio almost linearly decreased with increasing La2O3 content in x-0.80 ceramics. It is believed that Pb^2＋ vacancies were formed by La^3＋ substituting Pb^2＋ in La2O3-doped BI-PT ceramics. Tc shifted to lower temperature by 30 ℃/mol% La2O3. The maximum dielectric constant 8557 around 559 ℃ was exhibited in 0.5mol%-doped BI-0.80PT ceramics. La2O3-doped ceramics could be poled resulting from decreasing of c/a ratio and improving of dielectric loss and resistivity. The maximum piezoelectric coefficient d33 was 12 pC/N for 2mol%-doped BI-0.80PT ceramics.     

Electrical conductivity of （Na3AlF6-40%K3AlF6）-AlF3-Al2O3 melts

The effects of contents of AlF3 and Al2O3, and temperature on electrical conductivity of （Na3AlF6-40%K3AlF6）- AlF3-Al2O3 were studied by continuously varying cell censtant （CVCC） technique. The results show that the conductivities of melts increase with the increase of temperature, but by different extents. Every increasing 10 ℃ results in an increase of 1.85 × 10^-2, 1.86× 10^-2, 1.89 × 10^-2 and 2.20 × 10^-2 S/cm in conductivity for the （Na3AlF6-40%K3AlF6）-AlF3 melts containing 0%, 20%, 24%, and 30% AlF3, respectively. An increase of every 10 ℃ in temperature results an increase about 1.89× 10^-2, 1.94 × 10^-2, 1.95 × 10^-2, 1.99× 10^-2 and 2.10× 10^-2 S/cm for （Na3AlF6-40%K3AlF6）-AlF3-Al2O3 melts containing 0%, 1%, 2%, 3% and 4% Al2O3, respectively. The activation energy of conductance was calculated based on Arrhenius equation. Every increasing 1% of AlF3 results in a decrease of 0.019 and 0.020 S/cm in conductivity for （Na3AlF6-40%K3AlF6）-AlF3 melts at 900 and 1 000 ℃, respectively. Every increase of 1% Al2O3 results in a decrease of 0.07 S/cm in conductivity for （Na3AlF6-40%K3AlF6）-AlF3-Al2O3 melts. The activation energy of conductance increases with the increase in content of AlF3 and Al2O3.     

Kinetics mechanism of microwave sintering in ceramic materials

Based on the traditional sintering model incorporating the characteristic of microwave sintering, the ionic conductance diffusion mechanism in microwave sintering was studied. A flat-ball model was presented to describe the kinetics process in microwave sintering, and was applied to the sintering process of TZP and ZrO₂-Al₂O₃ ceramics. The results indicate that the shrinkage rate of materials in microwave sintering is proportional to t ^2/3 and r ^−4/3, respectively, where t is the sintering time and r is the particle radius. Whereas, the shrinkage rate of materials in conventional sintering is proportional to sintering time t ^2/5. Our model suggests that microwave sintering is faster than conventional sintering, which shows a good agreement with the experimental observation in sintering process of TZP and ZrO₂-Al₂O₃. Supported by the State Key Program of National Natural Science of China (Grant No. 50332010) and the National Key Technology Research and Development Program for Resource and Environment of China (Grant Nos. 2006BAB12B03, 2006BAB12B05)     

Forming regularity and relation between composition and property of B2O3-BaO-ZnO glass

B2O3-BaO-ZnO glass was prepared by using conventional melt quenching technology. The forming regularity and the relationship between the composition and the property of B2O3-BaO-ZnO glass were investigated. The results show that the composition range for forming B2O3-BaO-ZnO glass is very wide, but the content of B2O3 has a limit within mole fraction of 25%-75%. When the content of B2O3 is over the limit, the melt will be divided into two phases with different compositions and structures, whereas too low content of B2O3 will result in the crystallization of the melt during the cooling process. The thermal expansion coefficient, the transition temperature and the resistivity of the glass at room temperature are (5-10)×10-6 ℃-1, 480-620 ℃ and (1.5-3.0)×1010 Ω·m, respectively.     

Dielectric Properties of B2O3 Doped MgTiO3-CaTiO3 System Ceramics

The dielectric ceramics with a main crystal phase of MGTiO3 and additional crystal phase of CaTiO3 were prepared by the conventional electronic ceramics technology .the strucures of MgTiO3 are ilmenitetype,and belong to hexagonal syngony.the ratio of MgTiO3 to Ca TiO3 doping on the dielectric properties of MGTiO3-CaTiO3(MCT)ceranics were inrestigated.the addition of B2O3 decreases the sintering temperatnre and results in rapid desification without obrious negative effect on the Q values of the system(Q=1/tan ).B2O3 exists as liquid phase in the sintering process,promoting the reactions as a singering agent.