Microstructure and microwave dielectric properties of CaO-B2O3-SiO2 glass ceramics with various B2O3 contents

The effects of B2O3 addition on both the sintering behavior and microwave dielectric properties of CaO-B2O3-SiO2 (CBS) glass ceramics were investigated by Fourier transform infrared spectroscopy (FTIR),X-ray diffractometry (XRD) and scanning electron microscopy (SEM).The results show that the increasing amount of B2O3 causes the increase of the contents of [BO3],[BO4] and [SiO4],which deduces the increase of CaB2O4 and α-SiO2 and the decrease of CaSiO3 correspondingly.No new phase is observed throughout the...     

Effects of heat treatment temperature on crystallization and thermal expansion coefficient of Li2O-Al2O3-SiO2

The basic glass of Li₂O-Al₂O₃-SiO₂ system using P₂O₅ as nucleator was prepared by means of conventional melt quenching technology, and the heat-treatment process was determined by using differential thermal analysis. The crystalline phases and the microstructure of the glass-ceramics were investigated by using X-ray diffraction and scanning electron microscopy. The results show that the glass based on Li₂O-Al₂O₃-SiO₂ oxides using P₂O₅ as nucleator can be prepared at lower melt temperature of 1450°C and the glass-ceramics with lower thermal expansion coefficient of 21.6 × 10⁻⁷°C⁻¹ can also be obtained at 750°C. The glass-ceramics contain a few crystal phases in which the main crystal phase is β-quartz solid solution and the second crystal phase is β-spodumene solid solution. When the heat treatment temperature is not higher than 650°C, the transparent glass-ceramics containing β-quartz solid solution can be prepared. β-quartz solid solution changes into β-spodumene solid solution at about 750°C. And the appearance of the glass-ceramics changes from translucent, part opaque to complete opaque with increasing temperature.     

Low-temperature sintering and microwave dielectric properties of Li2MgTi3O8 ceramics doped with BaCu（B2O5）

The influences of BaCu(B₂O₅) (BCB) addition on sintering, microstructure and microwave dielectric properties of Li₂MgTi₃O₈ ceramics were investigated using X-ray diffractometry, scanning electron microscopy and microwave dielectric measurements. The experimental results show that a small amount of BaCu(B₂O₅) addition can effectively reduce the sintering temperature to 900 °C, and induce only a limited degradation of the microwave dielectric properties. Typically, the best microwave dielectric properties of ɛ _r=24.5, Q×f =24 622 GHz, τ _f=4.2×10⁻⁶ °C⁻¹ are obtained for 1.0% BCB-doped Li₂MgTi₃O₈ ceramics sintered at 900 °C for 3 h. The BCB-doped Li₂MgTi₃O₈ ceramics can be compatible with Ag electrode, which may be a strong candidate for low temperature co-fired ceramics applications.     

Electrical conductivity of （Na3AlF6-40%K3AlF6）-AlF3-Al2O3 melts

The effects of contents of AlF3 and Al2O3, and temperature on electrical conductivity of （Na3AlF6-40%K3AlF6）- AlF3-Al2O3 were studied by continuously varying cell censtant （CVCC） technique. The results show that the conductivities of melts increase with the increase of temperature, but by different extents. Every increasing 10 ℃ results in an increase of 1.85 × 10^-2, 1.86× 10^-2, 1.89 × 10^-2 and 2.20 × 10^-2 S/cm in conductivity for the （Na3AlF6-40%K3AlF6）-AlF3 melts containing 0%, 20%, 24%, and 30% AlF3, respectively. An increase of every 10 ℃ in temperature results an increase about 1.89× 10^-2, 1.94 × 10^-2, 1.95 × 10^-2, 1.99× 10^-2 and 2.10× 10^-2 S/cm for （Na3AlF6-40%K3AlF6）-AlF3-Al2O3 melts containing 0%, 1%, 2%, 3% and 4% Al2O3, respectively. The activation energy of conductance was calculated based on Arrhenius equation. Every increasing 1% of AlF3 results in a decrease of 0.019 and 0.020 S/cm in conductivity for （Na3AlF6-40%K3AlF6）-AlF3 melts at 900 and 1 000 ℃, respectively. Every increase of 1% Al2O3 results in a decrease of 0.07 S/cm in conductivity for （Na3AlF6-40%K3AlF6）-AlF3-Al2O3 melts. The activation energy of conductance increases with the increase in content of AlF3 and Al2O3.     

Study on the isothermal oxidation behavior in air of Ti3AlC2 sintered by hot pressing

The isothermal oxidation behavior at 900–1300°C for 20 h in air of bulk Ti₃AlC₂ with 2.8 wt% TiC sintered by means of hot pressing was investigated in the work. The isothermal oxidation behavior generally followed a parabolic rate law. The parabolic rate constants increased from 1.39×10⁻¹⁰ kg²·m⁻⁴·s⁻¹ at 900°C to 5.56×10⁻⁹ kg²·m⁻⁴·s⁻¹ at 1300°C. The calculated activation energy was 136.45 kJ/mol. It was demonstrated that Ti₃AlC₂ had excellent oxidation resistance due to the continuous, dense and adhesive protect scales consisted of a mass of α-Al₂O₃ and a little of TiO₂ and/or Al₂TiO₅. In principle, the oxide scale was grown by the inward diffusion of O²⁻ and the outward diffusion of Ti⁴⁺ and Al³⁺. The rapid outward diffusion of cations usually resulted in the formation of cracks, gaps, and holes.     

Microstructure and microwave dielectric properties of lead borosilicate glass ceramics with Al2O3

The effects of Al₂O₃ addition on both the sintering behavior and microwave dielectric properties of PbO-B₂O₃-SiO₂ glass ceramics were investigated by Fourier transform infrared spectroscope (FTIR), differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that with the increase of Al₂O₃ content the bands assigned to [SiO₄] nearly disappear. Aluminum replaces silicon in the glass network, which is helpful for the formation of boron-oxygen rings. The increase of the transition temperature T _g and softening temperature T _f of PbO-B₂O₃-SiO₂ glass ceramics leads to the increase of liquid phase precipitation temperature and promotes the structure stability in the glasses, and consequently contributes to the decreasing trend of crystallization. Densification and dielectric constants increase with the increase of Al₂O₃ content, but the dielectric loss is worsened. By contrast, the 3% (mass fraction) Al₂O₃-doped glass ceramics sintered at 725 °C have better properties of density ρ=2.72 g/cm³, dielectric constant ɛ _r =6.78, dielectric loss tan δ=2.6×10⁻³ (measured at 9.8 GHz), which suggest that the glass ceramics can be applied in multilayer microwave devices requiring low sintering temperatures.     

The Effect of Bi2O3 on the Structure and Microwave Dielectric Properties of Ba6-3xNd8＋2xTi18O54 System（x=2/3）

The structures and dielectric properties of Ba6-3xNd8＋2xTi18O54 system（x=2/3） doped with different contents of Bi2O3, whose final molecular formula is Ba6-3x（Nd1-yBiy）8＋2xTi18O54 were investigated. It is indicated that the dielectric constant increases greatly whereas Q value（f0=4 GHz） decreases with the increase of Bi2O3 content. However, the temperature coefficient could be controlled below 0±30×10^-6/℃ in the experiment. These phenomena are related to the appearance of a new phase, Bi4Ti3O12, which has high dielectric constant. Also, that Bi^3＋（0.13 nm） substitutes for Nd^3＋（0.099 5 nm） will increase the unit cell volume, which will lead to the enlargement of the octahedron B site occupied by Ti^4＋. So the spontaneous polarization of Ti^4＋ ions will be strengthened. Besides, Bi^3＋ will fill up some vacancies which Ba^2＋ or Nd^3＋ ions leave in two A1 sites and four A2 sites. More positive ions polarize, which also contributes to higher dielectric constant. The samples got with the optimium properties are sintered at 1 200 ℃ for 4 h, when y=0.25, ε≈110, Q≈5 400（f0=4 GHz）, TCC=-4.7×10^-6/℃; When y=0.3, ε≈120, Q≈5 000（f0=4 GHz）, TCC=-24×10^-6/℃.     

Preparation, characterization and dielectric properties of Sr5RTi3Ta7O30 (R=Pr and Eu) ferroelectric ceramics

Polycrystalline samples of Sr₅PrTi₃Ta₇O₃₀ (SPTT) and Sr₅EuTi₃Ta₇O₃₀ (SETT) compounds were prepared by high-temperature solid-state reaction method and their formation, structure and dielectric properties were studied. They are found to be ferroelectric phase of filled tetragonal tungsten bronze (TB) structure at room temperature and undergoes diffuse type of ferroelectric-paraelectric phase transition around 34 °C and 31 °C, respectively. At 1 MHz SPTT exhibits high dielectric constants of 177 and low dielectric losses of 3.5×10⁻⁴ and SETT has high dielectric constants of 125 and low dielectric losses of 2.4×10⁻³.     

Thermoelectric properties of Ca3Co4O9 ceramics

Ca₃Co₄O₉ ceramics were prepared using the sol-gel process with ordinary pressing sintering and their thermoelectric properties were measured from room temperature to 673 K. The experimental results show that single phase Ca₃Co₄O₉ can be fabricated at 750–900 °C in different citrate acid molar proportions for 0.2–1.0. For all the oxides, both the Seebeck coefficients S and the electrical conductivities κ increase with the increasing temperature. The Seebeck coefficients S are all positive. The thermal conductivities k increase with the increasing temperature also and the lattice thermal conductivity κ _l plays an important role to the thermal conductivity κ. The citrate acid molar proportions have a large influence on the particle sizes, which influences the thermoelectric properties of the ceramics. The figure of merit increases with the increasing temperature and reaches 4.5×10⁻⁵ K⁻¹ at 573 K for the sample in the citrate acid molar proportion of 0.46.     

Structural and Dielectric Properties of Ba5RNiNb9O30 （R = La, Nd and Sm） ceramics

1 IntroductionSince the discovery of ferroelectricity and relatedproperties in BaTiO3,a large amount of research work onoxidesin search of novel materials for industrial applica-tions ,has been done .High performance dielectric ceram-ics are applied as key materials for resonators , discreteand multiplayer (MLC) capacitors ,andtemperature com-pensating capacitors . Some ferroelectric oxides are alsovery important due to the rapid progress in microwavetelecommunications ,satellite broadcastin…     

Preparation and characteristics of Cu/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/MgF<Subscript>2</Subscript>/Au tunnel junction

The fabrication process of Cu/Al₂O₃/MgF₂/Au double-barrier metal/insulator/metal junction (DMIMJ) was introduced, and more stable light emission from this junction was successfully observed. The light emission physical mechanism of the junction was discussed. Results show that light emission spectrum of this structure locates at wavelength of 250–700 nm with two peaks at around 460 nm and 640 nm, which moves towards shorter wavelength region in comparison with that of the Al/Al₂O₃/Au junction. The light emission efficiency of this junction ranges from 0.7×10⁻⁵–2.0×10⁻⁵, which is 1 to 2 orders higher than that of the single-barrier Al/Al₂O₃/Au junction. The improved properties of this structure should be due to the electrons resonant tunneling effect in the double-barrier.     

Synthesis and characterization of arsenate antimonic acid AAAc(1 : 1)

The AAAc(1 : 1) was synthesized in water by As₂O₃ and Sb₂O₃ with molar ratio of 1 : 1. AAAc(1 : 1) was characterized by Raman, IR, TG/DTG, DSC, XPS and XRD. The results show that there are four peaks to v _s of As-OH, As-O-Sb, Sb-OH and Sb-O-Sb in Raman spectra of AAAc(1 : 1) at 100 – 1 000 cm⁻¹. The solution of AAAc(1 : 1) was also titrated with KOH solution. The titration results show that AAAc(1 : 1) is a hexabasic acid with dissociation constants of k ₁=3.62 × 10⁻², k ₂=3.05 × 10⁻³, k ₃=6.43 × 10⁻⁶, k ₄ =9.78 × 10⁻⁸, k ₅=1.32 × 10⁻¹¹, k ₆=3.87 × 10⁻¹². AAAc(1 : 1) has a good solubility and stability in water, its solid obtained by free volatilizing water from its solution under air at ambient temperature is amorphous. Chemical and thermal analysis show that the composition of AAAc(1 : 1) is As₂O₅ · Sb₂O₅ · 8H₂O in air at 25 °C. AAAc(1 : 1) has the structure of AsO(OH)₂-OH-Sb(OH)₄-O-Sb(OH)₄-OH-AsO(OH)₂ or As(OH)₃-O-Sb(OH)₄-O-Sb(OH)₄-O-As(OH)₃ (isomerism) through experimental determination and geometry optimization. Foundation item: Project(50274075) supported by the National Natural Science Foundation of China     

Effect of matrix composition on physical properties of Al<Subscript>3</Subscript>CON in-situ reaction reinforced corundum composite

60% white corundum used for aggregate, 5% aluminium powder for fixed additions and 35% various additives for matrix were prepared for specimens 1#,2#,3#. They were mixed uniformly with the suitable resin as a binder and pressed under pressure of 315 ton forging press, then dried at 200℃ for 24 h. Effects of various additives on 1500 ℃×2 h creep properties of Al3CON reinforced corundum composite were researched. The experimenal results show that creep coefficients of specimens 1#,2#,3# at 1500 ℃×2 h are 1.4×10^- 4, -9.4×10^-4, -22.6×10^-4, respectively. Crushing strength of the slide plate added with suitable additive A after fired at 1500 ℃ ×3 h reaches to 225 MPa, the creep rate is positive all the time from 0% to 0.014% at 1500 ℃ for 2 h. The microstructure result analysis shows that reinforced phases of Al3CON fiber composite have been formed after fired with Al powder in coke at high temperatures for specimen 1#, and the strength of the composite is increased. The hot modulus of rupture is up to 59 MPa at 1400 ℃ and the RUL is obviously higher than that at 1700 ℃. Its service life is two times as that of Al2O3-C slide plate when used in the process of pouring steel. The mechanism of creep rate resistance of the composites can be discovered by means of SEM and EDAX analysis. It is concluded that the active Al3CON and Al2O3 multiphases that were formed by N2 in gas, C, Al and Al2O3 inside the matrix of the composites during in-situ reaction,which gives the composites outstanding creep rate resistance for the dense zone resuiting from Al3CON oxidation that inhibits contraction at the high temperature. Besides, the matrix will turn into the multiphase with high refractoriness, N content and its Al3CON reinforced fiber will further increase accordingly. In addition, Al3CON formed by Al2O3 and C, Al in the matrix with N2 in gas will inhibit the creep rate and also greatly improve the creep rate resistance of the composites.     

Effect of ZnO-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glass addition on the microwave dielectric properties of BaO-Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The effect of ZnO-B₂O₃(ZB) glass addition on the sintering behavior, microstructures and microwave dielectric properties of BaO-Nd₂O₃-TiO₂-Bi₂O₃ (BNTB) system was investigated with the aid of X-ray diffraction, scanning electron microscopy and capacitance meter. It is found that the ZB glass addition, acting as a sintering aid, can effectively lower the sintering temperature of BNTB system to 850 °C. The dielectric constant of BNTB-ZB ceramics increases with the increase of soaking time and the value of dielectric loss decreased with increasing soak time. The optical dielectric properties at 1 GHz of ɛ=74, tan δ=4×10⁻⁴, and TCC=25 ppm/°c were obtained for the BNTB system doped with 25 wt% ZB glass sintered at 850 °C for 2 h, representing that the BNTB-ZB ceramics could be promising for multilayer low temperature co-fired ceramics applications.     

Preparation of LiFePO4 for lithium ion battery using Fe2P2O7 as precursor

In order to obtain a new precursor for LiFePO4, Fe2P2O7 with high purity was prepared through solid phase reaction at 650 ℃ using starting materials of FeC2O4 and NH4H2PO4 in an argon atmosphere. Using the as-prepared Fe2P2O7, Li2CO3 and glucose as raw materials, pure LiFePO4 and LiFePO4/C composite materials were respectively synthesized by solid state reaction at 700 ℃ in an argon atmosphere. X-ray diffractometry and scanning electron microscopy（SEM） were employed to characterize the as-prepared Fe2P2O7, LiFePO4 and LiFePO4/C. The as-prepared Fe2P2O7 crystallizes in the Cl space group and belongs to β-Fe2P2O7 for crystal phase. The particle size distribution of Fe2P2O7 observed by SEM is 0.4-3.0 μm. During the Li^＋ ion chemical intercalation, radical P2O7^4- is disrupted into two PO4^3- ions in the presence of O^2-, thus providing a feasible technique to dispose this poor dissolvable pyrophosphate. LiFePO4/C composite exhibits initial charge and discharge capacities of 154 and 132 mA·h/g, respectively.     

Effect of catalyst on structure of （PEO）8LiClO4-SiO2 composite polymer electrolyte films

（PEO）8LiClO4-SiO2 composite polymer electrolytes（CPEs） were prepared by in-situ reaction, in which ethyl-orthosilicate （TEOS） was catalyzed by HCl and NH3·H2O, respectively. The ionic conductivity, the contact angle and the morphology of inorganic particles in the CPEs were investigated by AC impedance spectra, contact angle method and TEM. The conductivities of acid-catalyzed CPE and alkali-catalyzed CPE are 2.2×10^-5 and 1.1×10^-5 S/cm respectively at 30 ℃. The results imply that the catalyst plays an important role in the structure of in-situ preparation of SiO2, and influences the surface energy and conductivity of CPE films directly. Meanwhile, the ionic conductivity is related to the surface energy.     

Effect of metallic phase species on the corrosion resistance of 17M/（10NiO-NiFe2O4） cermet inert anode of aluminum electrolysis

1 INTRODUCTIONThere are many disadvantages in the presentaluminumelectrolysis with carbon anode ,such assevere energy consumption,carbon wasting,envi-ronmental pollution and so on.Inert electrode sys-tem can overcome these disadvantages[1 3]. Re-cently ,the researches of the inert anode materialshave mainly been concentrated on alloys[4]and cer-met materials[5 ,6]. NiFe2O4based cermets , whichpossess not only high electrical conductivity ofmetal but also good corrosion resistance of cera…     

Preparation and properties of crystallizable Glass/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composites for LTCC material

The investigated low temperature Co fired ceramics(LTCC) composite of 60wt% CaO-Al2O3-B2O3-SiO2 glass and 40wt% α-Al2O3 as a filler is a non-reactive system, which is a critical part of the low temperature Co fired ceramics process. Through a study on densification process, the phase transformation and microstructure can be revealed. Its composites typically consist of CaO-Al2O3-B2O3-SiO2 glass and α-Al2O3 powders of average particle size (D50=3.49 mm). The sintering behavior, phase evaluation, sintered morphology, and microwave dielectric properties were investigated. In the fire range of 800 to 900 ℃, the composites were crystallized after completion of densification. It is found that the composites start to densify at 825 ℃, simultaneously, the dielectric constant (εr) reaches its maximum. With increasing heat-treatment temperatures, due to the loose microstructure of the material, tanδ increases slightly. The last of the sintered samples were identified as partly Anorthite at 850 ℃. At that temperature it has εr of 7.9 and tanδ less than 1×10-3, and can be used as a promising LTCC material.     

The Antibacterial Effect of Silver-carrying B2O3-SiO2-Na2O Glass Material

The antibacterial effect of carrying silver B2O3-SiO2-Na2 O gloss material was studied by means of antibacterial ring, nephelometery , MIC value, thin film attachment and microcalorimetry , respectively.The experimental results of five kinds of antibacterial test methods are almost identical and can verify that carrying silver B2 O3-SiO2-Na2 O glass material exerts an excellent antibacterial performance. Antibacterial ring and nephelometety are simple, quick, but the precision is restrictive. MIC value, thin film attachment method and meicrocalorimetry can quantitatively compare the antibacterial effects of the antibacterial glass material. Compared with the traditional microbe test methods, the microcalorimetry can analyze the inhibiting effect of the cell‘ s growth and metabolism on the antibacterial gloss material by monitoring the thermal effect continuously and automatically .     

Thermal expansion properties and hygroscopicity of Y2?xSmxW3O12 (x = 0.0–0.4) compounds

A novel class of solid solutions of Y_2−x Sm _x W₃O₁₂ (x = 0.0−0.4) were synthesized and studied by means of powder X-ray diffraction. All samples crystallize in an orthorhombic space group Pnca. The lattice parameters a, b and c of Y_2−x Sm _x W₃O₁₂ increase with increasing Sm content. Since the compounds of this series hydrate at room temperature, thermogravimetric (TG) analysis was carried out. The result shows that the compound stores less water with increasing Sm content. The thermal expansion properties of Y_2−x Sm _x W₃O₁₂ (x = 0.1, 0.3 and 0.4) were investigated with high temperature X-ray diffraction. Negative thermal expansion coefficient α _I becomes less negative from −6.644×10⁻⁶ to −6.211×10⁻⁶°C⁻¹ when x changes from 0.1 to 0.4.