Fully polarimetric airborne SAR and ERS SAR observations of snow: implications for selection of ENVISAT ASAR modes

Snow cover has a substantial impact on processes involved in the interaction between atmosphere and surface, and the knowledge of snow parameters is important in both climatology and weather forecasting. With the upcoming launch of Advanced Synthetic Aperture Radar (ASAR) instruments on Envisat, enhanced snow-mapping capabilities are foreseen. In this paper fully polarimetric C- and L-band airborne SAR data, ERS SAR and auxiliary data from various snow conditions in mountainous areas are analysed in order to determine the optimum ASAR modes for snow monitoring. The data used in this study are from the Norwegian part of the snow and ice experiment within the European Multi-sensor Airborne Campaign (EMAC'95) acquired in the Kongsfjellet area, located in Norway, 66°?N, 14°?E. Fully polarimetric C- and L-band SAR data from ElectroMagnetic Institute SAR (EMISAR), an airborne instrument operated by the Danish Center for Remote Sensing (DCR), were acquired in March, May, and July 1995. In addition, several ERS SAR, airborne photos, field and auxiliary data were acquired.

A larger separation between wet snow and bare ground in EMISAR C-VV polarisation data was found at high incidence angle (55°) compared to lower incidence angle (45°). Cross-polarized observations from bare ground, dry and wet snow in the incidence angle range 35° to 65° are below the specified Envisat ASAR noise floor of –20–22 dB. The backscattering angular dependency for wet snow and bare ground derived from EMISAR C-VV and ERS SAR data corresponds well, and agrees to some extent with volume and surface scattering model results. The C-band is more sensitive to variation in snow properties than the L-band.     

Monitoring snowmelt across the Arctic forest–tundra ecotone using Synthetic Aperture Radar

Detailed snowpack observations, meteorology, topography and landcover classification were integrated with multi‐temporal SAR data to assess its capability for landscape scale snowmelt mapping at the forest–tundra ecotone. At three sites along an approximately 8° latitudinal gradient in the Fennoscandian mountain range, 16 multi‐temporal spaceborne ERS‐2 synthetic aperture radar (SAR) were used for mapping snowmelt.

Comparison of field measurements and backscatter values demonstrates the difficulty of interpreting observed backscatter response because of complex changes in snow properties on diurnal and seasonal temporal scales. Diurnal and seasonal melt–freeze effects in the snowpack, relative to the timing of ERS‐2 SAR image acquisition, effectively reduce the temporal resolution of such data for snow mapping, even at high latitudes.

The integration of diverse data sources did reveal significant associations between vegetation, topography and snowmelt. Several problems with the application of thresholding for the automatic identification of snowmelt were encountered. These largely related to changes in backscattering from vegetation in the late stages of snowmelt. Due to the impact of environmental heterogeneity in vegetation at the forest–tundra ecotone, we suggest that the potential to map snow cover using single polarization C‐band SAR at the forest–tundra ecotone may be limited to tundra areas.     

Forest canopy height and carbon estimation at Monks Wood National Nature Reserve, UK, using dual-wavelength SAR interferometry

Forest canopy height is a critical parameter in better quantifying the terrestrial carbon cycle. It can be used to estimate aboveground biomass and carbon pools stored in the vegetation, and predict timber yield for forest management. Polarimetric SAR interferometry (PolInSAR) uses polarimetric separation of scattering phase centers derived from interferometry to estimate canopy height. A limitation of PolInSAR is that it relies on sufficient scattering phase center separation at each pixel to be able to derive accurate forest canopy height estimates. The effect of wavelength-dependent penetration depth into the canopy is known to be strong, and could potentially lead to a better height separation than relying on polarization combinations at one wavelength alone. Here we present a new method for canopy height mapping using dual-wavelength SAR interferometry (InSAR) at X- and L-band. The method is based on the scattering phase center separation at different wavelengths. It involves the generation of a smoothed interpolated terrain elevation model underneath the forest canopy from repeat-pass L-band InSAR data. The terrain model is then used to remove the terrain component from the single-pass X-band interferometric surface height to estimate forest canopy height. The ability of L-band to map terrain height under vegetation relies on sufficient spatial heterogeneity of the density of scattering elements that scatter L-band electromagnetic waves within each resolution cell. The method is demonstrated with airborne X-band VV polarized single-pass and L-band HH polarized repeat-pass SAR interferometry using data acquired by the E-SAR sensor over Monks Wood National Nature Reserve, UK. This is one of the first radar studies of a semi-natural deciduous woodland that exhibits considerable spatial heterogeneity of vegetation type and density. The canopy height model is validated using airborne imaging LIDAR data acquired by the Environment Agency. The rmse of the LIDAR canopy height estimates compared to theodolite data is 2.15 m (relative error 17.6%). The rmse of the dual-wavelength InSAR-derived canopy height model compared to LIDAR is 3.49 m (relative error 28.5%). From the canopy height maps carbon pools are estimated using allometric equations. The results are compared to a field survey of carbon pools and rmse values are presented. The dual-wavelength InSAR method could potentially be delivered from a spaceborne constellation similar to the TerraSAR system.     

Analysis of different polarimetric target decomposition methods in forest density classification using C band SAR data

The ability of synthetic aperture radar (SAR) C-band microwave energy to penetrate within forest vegetation makes it possible to extract information on crown components, which in turn gives a better approximation of relative canopy density than optical data-derived canopy density. Many studies have been reported to estimate forest biomass from SAR data, but the scope of C-band SAR in characterizing forest canopy density has not been adequately understood with polarimetric techniques. Polarimetric classification is one of the most significant applications of polarimetric SAR in remote sensing. The objective of the present study was to evaluate the feasibility of different polarimetric SAR data decomposition methods in forest canopy density classification using C-band SAR data. Landsat (Land Satellite) 5 TM (Thematic Mapper) data of the same area has been used as optical data to compare the classification result. RADARSAT (Radar Satellite)-2 image with fine quad-pol obtained on 27 October 2011 over tropical dry forests of Madhav National Park, India, was used for the analysis of full polarimetric data. Six decomposition methods were selected based on incoherent decomposition for generating input images for classification, i.e. Huynen, Freeman and Durden, Yamaguchi, Cloude, Van zyl, and H/A/α. The performance of each decomposition output in relation to each land cover unit present in the study area was assessed using a support vector machine (SVM) classifier. Results show that Yamaguchi 4-component decomposition (overall accuracy 87.66% and kappa coefficient (κ) 0.86) gives better classification results, followed by Van Zyl decomposition (overall accuracy 87.20% and κ 0.85) and Freeman and Durden (overall accuracy 86.79% and κ 0.85) in forest canopy density classification. Both model-based decompositions (Freeman and Durden and Yamaguchi4) registered good classification accuracy. In eigenvector or eigenvalue decompositions, Van zyl registered the second highest accuracy among different decompositions. The experimental results obtained with polarimetric C-band SAR data over a tropical dry deciduous forest area imply that SAR data have significant potential for estimating canopy density in operational forestry. A better forest density classification result can be achieved within the forest mask (without other land cover classes). The limitations associated with optical data such as non-availability of cloud-free data and misclassification because of gregarious occurrence of bushy vegetation such as Lantana can be overcome by using C-band SAR data.     

Correlation Analysis between L-band SAR and ForestStem Volume in Northeast China

Because Synthetic Aperture Radar(SAR)can penetrate into forest canopy and interact with the primary stem volume contents of the trees (trunk and branch),SAR data are widely used for forest stem volume estimation.This paper investigated the correlation between SAR data and forest stem volume in Xunke,Heilongjiang using the stand-wise forest inventory data in 2003 and ALOS PALSAR data for five dates in 2007.The influences of season and polarizations on the relationship between stem volume and SAR data were studied by analyzing the scatterplots;that was followed by interpretation of the mechanisms primarily based on a forest radar backscattering model-water cloud model.The results showed that the relationship between HV polarization backscatter and stem volume is better than HH polarization,and SAR data in summer dry conditions are more correlated to stem volume than the data acquired in other conditions.The interferometric coherence with 46-day temporal baseline is negatively correlated to the stem volume.The correlation coefficients from winter coherence are higher than those from summer coherence and backscatter.The study results suggest using the interferometric coherence in winter as the best choice for forest stem volume estimation with L-band SAR data.     

Application of a three-component scattering model over snow-covered first-year sea ice using polarimetric C-band SAR data

In this study we examine the utility of a three-component scattering model to quantify the sensitivity of radar incidence angle over snow-covered landfast first-year sea ice (FYI) during the late winter season. This three-component scattering model is based on (1) surface scattering contributed from the snow-covered FYI (smooth-ice (SI), rough-ice (RI), and deformed-ice (DI) types); (2) volume scattering contributed from snow layers which consist of enlarged snow grains, elevated brine volume, and preferential orientation of snow grains relative to radar look direction, as well as the underlying sea ice; and (3) double-bounce scattering contributed from ice ridges and ice fragments. This study uses RADARSAT-2 C-band polarimetric synthetic aperture radar (POLSAR) data acquired on 15 and 18 May 2009 for Hudson Bay, near Churchill, during late winter with surface air temperatures ≤?8°C at two different incidence angles (29° and 39°). The three-component scattering model is used to discriminate between snow-covered smooth, rough, and deformed FYI. The model shows enhanced discrimination at an incidence angle of 29°, compared with an incidence angle of 39°. The model is then used to quantify the sensitivity of radar incidence angle to each of the three scattering contributors. The results show that the relative fraction of surface scattering dominates for all three FYI types (SI ≈ 77.3%; RI ≈ 66.0%; and DI ≈ 61.1%) at 29° and decreases with increasing incidence angle and surface roughness. Volume scattering is found to be the second dominant mechanism (SI ≈ 19.1%, RI ≈ 32.2%, and DI ≈ 37.4% at 29° and SI ≈ 28.3%, RI ≈ 41.0%, and DI ≈ 49.5% at 39°) over snow-covered FYI and it increases with incidence angle and surface roughness. The double-bounce scattering contribution is low for all FYI types at both incidence angles.     

Calibration and modelling of MAESTRO 1 polarimetric SAR data of a forest area in Les Landes,France

Abstract. The results of an analysis of polarimetric P, Land C-band SAR data from the JPL AIRSAR of a forest area of maritime pine in Les Landes, southwest France, are described and discussed. The data were acquired in connection with the MAESTRO I Campaign organized by ESA and JRC/lspra. Cross-talk and channel imbalance distortions are removed in a calibration process using the SAR data itself and trihedral corner reflectors positioned at the scene. Two calibration methods have been implemented and compared: the iterative Klein algorithm and the non-iterative Quegan algorithm. Quegan's method shows the largest reduction of the cross-talk, and the most stable and easily interpreted results. Also, absolute calibration using the integral method has been performed. The results presented show that P band (and to some extent L band) is very sensitive to trunk biomass using single-polarization radar data, at least at the incidence angles in the range from 38° to 52°, whereas C band is less sensitive. Also, the cylinder model by Durden et al. of the baekseattering from a forest has been implemented and the results show good agreement with the SAR data. The dominant scattering mechanisms have been determined using the model at P and L bands.     

Detecting changes in surface soil moisture content using differential SAR interferometry

The feasibility of measuring changes in surface soil moisture content with differential interferometric synthetic aperture radar (DInSAR) has received little attention in comparison with other active microwave techniques. In this study, multi-polarization C- and L-band DInSAR is explored as a potential tool for the measurement of changes in surface soil moisture in agricultural areas. Using 10 ascending phased array L-band SAR (PALSAR) scenes acquired by the Japanese Advanced Land Observing Satellite (ALOS) and 12 descending advanced SAR (ASAR) scenes acquired by the European ENVISAT satellite between July 2007 and November 2009, a series of 27 differential interferograms covering a common study area over southern Ireland were generated to investigate whether small-scale changes in phase are linked to measured soil moisture changes. Comparisons of observed mean surface displacement and in situ mean soil moisture change show that C-band cross-polarization pairs displayed the highest correlation coefficients over both the barley (correlation coefficient, r = 0.51, p = 0.04)- and potato crop (r = 0.81, p = 0.003)-covered fields. Current results support the hypothesis that a soil moisture phase contribution exists within differential interferograms covering agricultural areas.     

Influence of incidence angle on detecting flooded forests using C-HH synthetic aperture radar data

Hydrology is the single most important abiotic factor in the formation and functioning of a wetland. Many limitations still exist to accurately characterizing wetland hydrology over large spatial extents, especially in forested wetlands. Imaging radar has emerged as a viable tool for wetland flood mapping, although the limitations of radar data remain uncertain. The influence of incidence angle on the ability to detect flooding in different forest types was examined using C-HH Radarsat-1 data (23.5°, 27.5°, 33.5°, 39.0°, 43.5°, and 47.0°) during the leaf-off and leaf-on seasons. The ability to detect flooding under leaf-on conditions varied much more according to incidence angle while forest type (open canopy tupelo-cypress, tupelo-cypress, and bottomland hardwood) had a greater effect during the leaf-off season. When all forest types were considered together, backscatter generally decreased with increasing incidence angle under all conditions (2.45 dB between 23.5° and 47.0° flooded, leaf-off; 2.28 dB between 23.5° and 47.0° not flooded, leaf-off; 0.62 between 23.5° and 43.5° flooded, leaf-on; 1.73 dB between 23.5° and 43.5° not flooded, leaf-on; slope was not constant between incidence angles), but the distinction between flooded and non-flooded areas did not decline sharply with incidence angle. Differentiation of flooded and non-flooded forests was similar during the leaf-off and leaf-on seasons. The ability to detect inundation under forest canopies was less than expected at smaller incidence angles and greater than expected at larger incidence angles, based on the results of previous studies. Use of a wider range of incidence angles during the entire year increases the temporal resolution of imagery which may, in turn, enhance mapping of inundation beneath forest canopies.     

Evaluating ERS-1 SAR data for the discrimination of tropical forest from other tropical vegetation types in Papua New Guinea

ERS-1 Synthetic Aperture Radar (SAR) data over a study area located in Papua New Guinea, where there is a high probability of cloud cover, are evaluated on their information content for mapping tropical forest ecosystems. The feasibility of forest/non-forest discrimination using mono- and multi-temporal ERS-1 SAR data at 100m pixel size is investigated using two different classification methodologies. An assessment of the optimal acquisition period and number of acquisitions is undertaken. The automatic classification results are compared quantitatively with the aid of field observations in a comparative accuracy assessment methodology, and a comparison is made with Landsat Thematic Mapper (TM) data. Finally, the potential of ERS-1 SAR data for the discrimination of tropical forest types is investigated. The results showed that multi-temporal ERS-1 SAR data acquired at the appropriate times were found to have a high potential for forest/nonforest discrimination and achieved similar classification accuracies to the TM data. The discrimination of forest types proved difficult. However, discrimination was possible between dense and open forest types having different canopy structures.     

Estimating the characteristics of vegetation canopies with airborne radar measurements

Abstract

Possible use of synthetic aperture radars (SAR) for monitoring agricultural canopies is investigated in this paper. Data have been acquired on the Orgcval watershed during the AGRISCATT'88 campaign. Four radar experiments were carried out with the airborne scattcrometer ERASME (C and X bands, HH and VV polarizations, multi-incidence angles). Simultaneous ground measurements (soil moisture, leaf area index, water content of the canopy) were conducted on 11 wheat fields. Backscattering coefficients of the canopies arc interpreted in the framework of semi-empirical ‘water-cloud’ models. A simple paramctrization of the angular effect of soil roughness is introduced, allowing the simultaneous use of multi-incidence angle radar data. With a unique set of parameters for each radar configuration ‘ frequency and polarization’ the water-cloud model appears to describe adequately the backscattering of all the fields, over the range of incidence angles. It is shown that in this case, attenuation is the dominant effect of the vegetation and an inversion algorithm is proposed for estimating the water content of vegetation. This algorithm requires measurements at two different incidence angles and various combinations of radar configurations are then tested.     

Forest biomass mapping from lidar and radar synergies

The use of lidar and radar instruments to measure forest structure attributes such as height and biomass at global scales is being considered for a future Earth Observation satellite mission, DESDynI (Deformation, Ecosystem Structure, and Dynamics of Ice). Large footprint lidar makes a direct measurement of the heights of scatterers in the illuminated footprint and can yield accurate information about the vertical profile of the canopy within lidar footprint samples. Synthetic Aperture Radar (SAR) is known to sense the canopy volume, especially at longer wavelengths and provides image data. Methods for biomass mapping by a combination of lidar sampling and radar mapping need to be developed.In this study, several issues in this respect were investigated using aircraft borne lidar and SAR data in Howland, Maine, USA. The stepwise regression selected the height indices rh50 and rh75 of the Laser Vegetation Imaging Sensor (LVIS) data for predicting field measured biomass with a R² of 0.71 and RMSE of 31.33 Mg/ha. The above-ground biomass map generated from this regression model was considered to represent the true biomass of the area and was used as a reference map since no better biomass map exists for the area. Random samples were taken from the biomass map and the correlation between the sampled biomass and co-located SAR signature was studied. The best models were used to extend the biomass from lidar samples into all forested areas in the study area, which mimics a procedure that could be used for the future DESDYnI mission. It was found that depending on the data types used (quad-pol or dual-pol) the SAR data can predict the lidar biomass samples with R² of 0.63-0.71, RMSE of 32.0-28.2 Mg/ha up to biomass levels of 200-250 Mg/ha. The mean biomass of the study area calculated from the biomass maps generated by lidar-SAR synergy was within 10% of the reference biomass map derived from LVIS data. The results from this study are preliminary, but do show the potential of the combined use of lidar samples and radar imagery for forest biomass mapping. Various issues regarding lidar/radar data synergies for biomass mapping are discussed in the paper.     

Synthetic aperture radar imaging of ocean-bottom topography via tidal-current interactions: theory and observations

A numerical model has been developed for the purpose of explaining and quantifying the relationship between the SEASAT synthetic aperture radar (SAR)signatures and the bottom topography of the ocean in the Southern Bight of the North Sea and Nantucket Shoals. The model uses environmental data (wind, current and depth changes)and radar system parameters (frequency, polarization, incidence angle and resolution cell size)as inputs and predicts SAR-observed backscatter changes over topographic changes in the ocean floor. The model results compare favourably with the actual SEASAT SAR-observed backscatter values. The comparisons between the model and the actual data are all within 1·5?dB except for one limiting geometry. The model suggests that for bottom features to be visible on SAR imagery, a moderate to high current velocity (0·4?m/s or greater) and a low to moderate wind (between 1·5 and 7·5?m/s) must be present.     

Assessment of the ASAR sensor radiometric quality in comparison to ERS‐2 and RADARSAT‐1 SAR data

The estimation of geophysical parameters from Synthetic Aperture Radar (SAR) data necessitates well‐calibrated sensors with good radiometric precision. In this paper, the radiometric calibration of the new Advanced Synthetic Aperture Radar (ASAR‐ENVISAT) sensor was assessed by comparing ASAR data with ERS‐2 and RADARSAT‐1 SAR data. By analysing the difference between radar signals of forest stands, the results show differences of varying importance between the ASAR on the one hand, and the ERS‐2 and the RADARSAT‐1 on the other. For recent data acquired at the end of 2005, the difference varies from ?0.72 to +0.72 dB, with temporal variations that can reach 1.1 dB. For older data acquired in 2003 and 2004, we observe a sharp decrease in the radar signal in the range direction, which can attain 3.5 dB. The use of revised calibration constants provided recently by the European Space Agency (ESA) significantly improves the results of the radiometric calibration, where the difference between the ASAR and the other SARs will be lower than 0.5 dB.     

The effects of changes in forest biomass on radar backscatter from tree canopies

We validated a canopy backscatter model for loblolly pine forest stands at the Duke Forest, North Carolina, by comparing the observed and modelled SAR backscatter from the stands. Given the SAR backscatter data calibration uncertainty, the model made good predictions of C-HH, C-HV, L-HH, L-HV, L-VV, P-HH, and P-HV backscatter for most of 25 stands studied. The model overestimated C-VV backscatter for several stands, and largely overestimated P-VV backscatter for most of the stands. Using the collected SAR backscatter and ground data, and the backscatter model, we studied the influences of changes in biomass on SAR backscatter as a function of radar frequency and polarization, and evaluated the feasibility of deriving the biomass from the backscatter. This study showed that C-HH, C-HV, C-VV, L-VV, and P-VV SAR backscatter may be insensitive to the biomass change. L-HH, L-HV, P-HH, and P-HV SAR backscatter changed more than 5dB as the biomass varied. This study also showed that the L-HH and P-HH backscatter or L-HV and P-H V backscatter may be used to develop algorithms to retrieve trunk biomass or canopy biomass of the loblolly pine forests.     

Potential of SAR for forest bole volume estimation

MAESTRO I data from the Flevoland lest site in the Netherlands have been used for this study. From a complementary ground data collection, the bole volumes of a large number of stands of mainly poplar and ash have been estimated. The relationships between radar backscattering and bole volumes have been examined experimentally and theoretically. In the case studied, the radar backscattering sensitivity to bole volumes increases as the wavelengths increase. and is highest at P band. The sensitivity of the radar backscattering to variations of forest canopy components and moisture contents has been investigated theoretically at P band. It is important to obtain information on such variations before the inversion problem can be solved. The present study indicates a potential for bole volume determination by P-band SAR.     

Comparison of annual changes in winter ERS-1 SAR images and glacier mass balance of Slakbreen,Svalbard

The Arctic glaciers are sensitive to climate change, and glacier mass balance is used as an indicator of climate change. However, few mass balance observations are available from the Arctic region. Winter ERS-1 SAR images of the Arctic glacier Slakbreen (78degreesN, 16degrees 30'E) on Svalbard were analysed to investigate a possible relation between SAR backscatter and temporal variations in glacier mass balance. A winter ERS-1 SAR image acquired in 1993 after a summer with large ablation was compared with a winter ERS-1 SAR image acquired after the following summer with low ablation. Changes in mass balance from one year to another were difficult to detect using SAR backscatter data only. Comparison of ground-penetrating radar and SAR data showed that the SAR data contain a signal of the near-surface glacier properties. SAR data were interpreted to reflect variations in accumulation and ablation integrated over several years.     

Development of polarization ratio model for sea surface wind field retrieval from TerraSAR-X HH polarization data

In this article, the polarization ratio (PR) of TerraSAR-X (TS-X) vertical–vertical (VV) and horizontal–horizontal (HH) polarization data acquired over the ocean is investigated. Similar to the PR of C-band synthetic aperture radar (SAR), the PR of X-band SAR data also shows significant dependence on incidence angle. The normalized radar cross-section (NRCS) in VV polarization data is generally larger than that in HH polarization for incidence angles above 23°. Based on the analysis, two PR models proposed for C-band SAR were retuned using TS-X dual-polarization data. A new PR model, called X-PR hereafter, is proposed as well to convert the NRCS of TS-X in HH polarization to that in VV polarization. By using the developed geophysical model functions of XMOD1 and XMOD2 and the tuned PR models, the sea surface field is retrieved from the TS-X data in HH polarization. The comparisons with in situ buoy measurements show that the combination of XMOD2 and X-PR models yields a good retrieval with a root mean square error (RMSE) of 2.03 m s^–1 and scatter index (SI) of 22.4%. A further comparison with a high-resolution analysis wind model in the North Sea is also presented, which shows better agreement with RMSE of 1.76 m s^–1 and SI of 20.3%. We also find that the difference between the fitting of the X-PR model and the PR derived from TS-X dual-polarization data is close to a constant. By adding the constant to the X-PR model, the accuracy of HH polarization sea surface wind speed is further improved with the bias reduced by 0.3 m s^–1. A case acquired at the offshore wind farm in the East China Sea further demonstrates that the improvement tends to be more effective for incidence angles above 40°.     

Surface soil moisture estimation over dense crop using Envisat ASAR and Landsat TM imagery: an approach

This study focuses on developing a new method of surface soil moisture estimation over wheat fields using Environmental Satellite Advanced Synthetic Aperture Radar (Envisat ASAR) and Landsat Thematic Mapper (TM) data. The Michigan Microwave Canopy Scattering (MIMICS) model was used to simulate wheat canopy backscattering coefficients from experiment plots at incidence angles of 23° (IS2) and 43.9° (IS7). Based on simulated data, the scattering characteristics of a wheat canopy were first investigated in order to derive an optimal configuration of polarization (HH) and incidence angle (IS2) for soil moisture estimation. Then a parametric model was developed to describe wheat canopy backscattering at the optimal configuration. In addition, direct backscattering and two-way transmissivity of wheat crowns were derived from the TM normalized difference vegetation index (NDVI); direct ground backscattering was derived from surface soil moisture and TM NDVI; and backscattering from double scattering was derived from total backscattering. A semi-empirical model for soil moisture estimation was derived from the parametric model. Coefficients in the semi-empirical model were obtained using a calibration approach based on measured soil moisture, ASAR, and TM data. A validation of the model was performed over the experimental area. In this study, the root mean square error (RMSE) for the estimated soil moisture was 0.041 m³ m^?3, and the correlation coefficient between the measured and estimated soil moisture was 0.84. The experimental results indicate that the semi-empirical model could improve soil moisture estimation compared to an empirical model.     

Estimating forest structure in wetlands using multitemporal SAR

Data from 202 forest plots on the Roanoke River floodplain, North Carolina were used to assess the capabilities of multitemporal radar imagery for estimating biophysical characteristics of forested wetlands. The research was designed to determine the potential for using widely available data from the current set of satellite-borne synthetic aperture radar (SAR) sensors to study forests over broad geographic areas and complex environmental gradients. The SAR data set included 11 Radarsat scenes, 2 ERS-1 images, and 1 JERS-1 scene. Empirical analyses were stratified by flood status such that sites were compared only if they exhibited common flooding characteristics. In general, the results indicate that forest properties are more accurately estimated using data from flooded areas, probably because variations in surface conditions are minimized where there is a continuous surface of standing water. Estimations yielded root mean square errors (RMSEs) for validation data around 10 m²/ha for basal area (BA), and less than 3 m for canopy height. The r² values generally exceeded .65 for BA, with the best predictions coming from sample sites for which both nonflooded and flooded SAR scenes were available. The addition of early spring normalized difference vegetation index (NDVI) values from Landsat Thematic Mapper (Landsat TM) improved model predictions for BA in forests where BA levels were <55 m²/ha. Further analyses indicated a very limited sensitivity of the individual SAR scenes to differences in forest composition, although soil properties in nonflooded areas exerted a weak but nevertheless important influence on backscatter.