稀土镁合金的研究

本文总结了稀土镁合金的研究工作。概要论述了稀土镁合金的发展进程;在稀土元素对镁合金性能影响方面,阐明了稀土元素对镁合金密度、电阻系数和导热系数、热膨胀系数、阻尼容量、晶格常数、弹性模量等物理性能以及对拉伸和蠕变等力学性能的影响。在稀土镁合金微观结构研究方面,总结了稀土相的结构,以及稀土相对合金的强化作用,并提出了我们的一些研究结果。     

稀土元素对镁合金力学行为影响的研究现状

系统论述了不同稀土元素的结构特性,基于镁合金的强化机制,并结合当前稀土镁合金的研究现状,展示了稀土元素的添加对镁合金在强度、塑性及抗蠕变性能等方面带来的变化,尤其是对镁合金塑性的影响.其中,区别于传统的强化机制,对添加稀土元素后出现的LPSO结构相对镁合金性能的影响也进行了重点讨论,进一步对镁合金中的稀土元素合金化后的改性作用及前景进行了探讨和展望.     

稀土元素对镁合金力学行为影响的研究现状（英文）

系统论述了不同稀土元素的结构特性,基于镁合金的强化机制,并结合当前稀土镁合金的研究现状,展示了稀土元素的添加对镁合金在强度、塑性及抗蠕变性能等方面带来的变化,尤其是对镁合金塑性的影响。其中,区别于传统的强化机制,对添加稀土元素后出现的LPSO结构相对镁合金性能的影响也进行了重点讨论,进一步对镁合金中的稀土元素合金化后的改性作用及前景进行了探讨和展望。     

耐热镁合金及其相图热力学研究及应用进展

镁合金常温力学性能较好,但高温力学性能较差,特别是高温抗蠕变性能较差.综述了国内外耐热镁合金的研究现状,重点分析了Mg-Al、Mg-Zn、Mg-RE等系耐热镁合金高温抗蠕变机制,合金元素对耐热性的影响和耐热镁合金相图热力学的研究进展,最后对耐热镁合金的工业应用现状进行综述,并指出了未来耐热镁合金的研究方向和重点.     

高性能稀土镁合金的研究进展

随着近年来汽车等工业节能减排对更高性能轻质镁合金的迫切需求,镁合金在工业应用中展现出了很大的发展前途。稀土镁合金系由于具有高温强度高、优良抗蠕变性能及耐热性能以及良好的塑性和耐腐蚀性等高性能,已经成为越来越受到重视的镁合金系之一,并在航空航天、电子、汽车、通讯等领域得到了广泛应用。目前,国内外已开发了Mg-Gd、Mg-Y、Mg-Gd-Y、Mg-Y-Gd等一系列稀土镁合金。综述了高性能稀土镁合金的研究进展和应用现状,主要介绍了Mg-Y和Mg-Gd二元和多元合金系的研究开发及应用的新进展,以及含长周期堆垛有序结构(Long Period Stacking Ordered Structure,简称LPSO结构)的Mg-Y-Zn、Mg-Gd-Zn、Mg-Gd-Y-Zn、Mg-Y-Gd-Zn合金系的研究现状。最后,展望了高性能稀土镁合金的发展趋势。     

压铸镁合金的研究进展及发展趋势EI北大核心CSCD

本文对镁合金现有的各种压铸技术、添加元素提高镁合金蠕变性能、耐蚀性能和镁合金熔炼新技术等方面的研究进展进行了综述;分析了压铸技术、添加合金元素以及对熔体进行净化和气体保护对压铸镁合金抗高温蠕变和耐腐蚀性能的作用;最后,指出了今后压铸镁合金的发展方向。     

稀土在镁及镁合金中的作用

综述了稀土元素在镁合金溶液中去氧化夹杂、除氢和与熔剂的相互作用,以及稀土元素对镁及镁合金的组织、性能、起燃温度、耐蚀性等方面的影响.阐述了RE在镁合金显微组织中细化晶粒、强化晶粒和晶界、提高合金力学性能的机理,以及与氧等元素反应在镁合金表面生成MgO、Al2O3、RE2O3、Mg17Al12组成的致密保护膜和由于Ce、Y、Le等元素的加入形成稀土转化膜对镁合金起燃温度、耐蚀性的作用.并对含稀土镁合金进行了评价与展望.     

阻燃镁合金的研究现状

介绍了镁合金的阻燃机制,综述了阻燃镁合金的研究现状,分析了合金元素Ca,Be,Zn和稀土在阻燃镁合金中的作用,指出了其作为镁合金添加元素的优点和不足之处.阻燃镁合金正向着合金多元化的方向发展,多种合金元素相互匹配,既可达到阻燃的目的,又能不破坏镁合金的性能.阻燃镁合金中添加元素在液面上的化学反应过程及其热力学、动力学机制尚不清楚,需要在此方面进行深入地研究.     

硼与稀土对镁合金作用的研究进展

镁合金作为最轻的工程材料,显示了镁合金在工业中的重要地位。针对硼、稀土在镁合金中的应用,根据国内外的研究现状,分别从硼、稀土对镁合金的细化晶粒、净化合金和耐腐蚀性等作用,探讨了镁合金的力学性能。展望了硼与稀土对镁合金作用的研究方向和发展趋势。     

锑合金化在镁合金中的应用

综述了近年来含锑镁合金的研究进展,总结了锑元素对Mg-Al和Mg-Zn系镁合金铸造性能、金相组织、力学性能、蠕变性能、阻尼性能、耐蚀性能6方面的影响。最后,展望了含锑镁合金的研究方向。     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Effect of Permeable Crystalline Material on Steel Reinforcement Corrosion of Concrete

Permeable crystalline materialcan permeate into pores and cracks of concrete and catalyze the reaction between Ca(OH) 2and unhydrated cement to generate a great quantity needle non-soluble crystals, which can stop up the pores and cracks of concrete, and increase the impermeability of concrete. This paper reported the results of a study conducted to evaluate steel reinforcement corrosion of concrete specimens uncoated and coated with permeable crystalline material as well as mixed with the permeable crystalline material. The properties evaluated for corrosion test were water impermeability, water absorption, compressive strength and potential. The results of water impermeability, water absorption, compressive strength clearly showed that the permeable crystalline material could prohibit water, any soluble salts and moisture from penetrating the concrete to cause corrosion, leaking, and other problems, and it did increase the compressive strength, which was favorable for protection of corrosion of reinforcing steel. Moreover, it was concluded from the potential-time curve that the steel reinforcement of uncoated specimen was in the state of activation whereas that of other specimens coated and mixed with the permeable crystalline material was in the state of inactivation. Above all, it was indicated that the permeable crystalline materialis very effective to protect the steel reinforcement of concrete from corrosion.     

The Research and Application About "Dry Peeling Off" Technology for Airplane Surface Paint Layer

In this paper, the principle of spurting take off lacquer were introduced; and with orthogonal method the unsaturate polyester was prepared ;it was easy to peel airplane paint layer off with this material and equipment.     

Quality Study of Honeycomb Core Shaping Without Wax Stabilization

Sandwich panels utilizing honeycomb cores result in lightweight, high-strength units that are very rigid. Indeed, they give honeycomb panels the best strength-to-weight ratio of any construction type available. Conventionally, the wax is poured into the cell of the core to strengthen the structure and prevent the core from being crushed during milling. Much time and labor is required to wax, mill, and clean the cores. In this study, the process of pouring wax into the core was skipped. In other words, the cutter directly milled the core. Experiments showed that the compressive strength of the core produced without wax stabilization was only 3% lower than that of cores produced using the traditional method. In addition, the drum peel strengths of cores produced without wax stabilization were 38.4% higher than cores produced using the traditional method, in which residual wax seriously polluted the adhesive. It was also found that eliminating the wax process can reduce costs.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

In-process thermal treatment of polylactic acid in fused deposition modelling

Polylactic acid (PLA) is one of the most widely used open source fused filament fabrication materials due to its ease of extrusion, biodegradability, and mechanical strength. The mechanical strength of PLA largely depends on the proper growth of its semi-crystalline structure, which can be severely impaired by a low rate of crystallization, particularly in open source printers. This can be further aggravated by the non-uniform thermal distribution of heat that causes improper curing among the extruded beads of the printing material. As a result, PLA printed on open source printers does not achieve the best mechanical properties. This research, for the first time, proposes an additive-free solution implemented through a detailed set of experimentation to improve the curing rate through in-process temperature variations to cure the joints among the beads. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy is used to confirm the improvements in the bead joints. This work is conducted in two phases of experiments. In the first phase, a full factorial ANOVA is used to investigate various process parameters and the important variables are used in the second phase to print test specimens in four different sets.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.