微束等离子喷涂羟基磷灰石涂层

采用微束等离子喷涂(MPS) 在Ti6Al4V基体上制备了羟基磷灰石(HA)涂层, 并以大气等离子喷涂(APS)为对照. 利用光学显微镜、SEM和XRD分析技术对MPS涂层形貌、相组成和结晶度进行了研究. 结果表明: 在微束等离子喷涂过程中, HA 的分解程度比大气等离子喷涂有显著降低, 除了HA相, 仅形成β-TCP相和非晶相. MPS涂层的结晶度主要受喷涂距离的影响. 喷涂距离较短(<80mm)时, 涂层结晶度高于APS方法制备的涂层. 喷涂距离在130mm时, 涂层结晶度低. 大气等离子喷涂层含有β-TCP、α-TCP、TTCP、CaO和非晶. MPS涂层分解较APS少的主要原因是喷涂过程中HA粒子过热不严重.     

热处理对羟基磷灰石涂层相组成、表面形貌与结合强度的影响

羟基磷灰石(HA)涂层的喷涂及其后处理工艺对其组织结构和结合强度具有重要影响.比较了热处理对不同粒度HA涂层相组成、表面形貌与结合强度的影响,为该类涂层制备工艺的优化提供实验依据.采用等离子喷涂法在纯钛表面制备了不同粒度的HA涂层,对其进行650℃不同保温时间的后热处理.利用X射线衍射仪、扫描电子显微镜和电子拉伸机检测了涂层的相组成、表面与断口形貌及剪切结合强度等.结果表明,涂层经650℃保温0.5h热处理后,非晶相和分解相基本全部转变为结晶HA.经热处理晶化后,涂层表面生成300nm以下的微粒子,双重涂层BC表面更易形成.粗粉末涂层CC和BC热处理后的剪切强度提高,而细粉末涂层FC则相反;HA涂层的剪切断裂主要是发生在涂层与基体间的界面上.     

HVOF喷涂纳米WC-17Co涂层组织结构及力学行为研究

利用超音速火焰喷涂(HVOF)技术制备了普通、超细纳米WC-17Co涂层.研究了喷涂粉末、涂层的微观组织结构和物相成分,测试了涂层的显微硬度、弹性模量、断裂韧性.研究表明,纳米WC-17Co涂层中形成了纳米尺度的胞状结构和长条状结构,并有网状的非晶结构生成.WC-17Co涂层表面均匀致密,3种涂层均是由熔化再结晶区、半熔化区和未熔化区等构成.涂层中条带结构不明显,明显区别于等离子涂层.纳米涂层组织结构更致密,碳化物颗粒分布更均匀.3种涂层中,WC都是主相,W2C、Co6W6C的含量很少.纳米涂层的显微硬度、弹性模量、断裂韧性最高.     

低压等离子喷涂316L等轴晶涂层及其性能研究

为研究低压等离子喷涂等轴晶涂层组织性能和形成机理,采用大气等离子喷涂（APS）和低压等离子喷涂（LPPS）,分别制备了316L不锈钢涂层.利用金相显微镜,X射线衍射和显微硬度等方法,分析了2种涂层的金相组织、相结构、显微硬度和耐蚀性.结果表明：一定条件下制备的低压等离子喷涂SUS316L不锈钢涂层明显不同于传统大气等离...     

Ti-6Al-4V合金基体等离子喷涂生物活性羟基磷灰涂层的研究进展

系统阐述了在钛合金(Ti-6Al-4V)表面等离子喷涂羟基磷灰石(HA)涂层的研究进展.描述了等离子喷涂制备HA涂层的工艺过程、微观形貌和化学组成.综述几种综合性能较高的复合型涂层:HA/BG(生物活性玻璃)复合涂层,HA/ZrO2复合增强型涂层,HA/Ti涂层,HA/Ti-6Al-4V梯度涂层;并对HA涂层发展趋势进行了展望.     

不同喷涂工艺下NiCoCrAlYTa涂层的显微结构和性能

为探索不同喷涂工艺对NiCoCrAlYTa涂层的显微结构和性能的影响规律,确定最优工艺,采用大气等离子、低压等离子、常规超音速火焰和低温超音速火焰4种工艺在镍基单晶高温合金表面制备了NiCoCrAlYTa涂层。采用X射线衍射(XRD)、扫描电镜(SEM)和显微硬度计等分析手段对喷涂态涂层的相组成、显微结构和显微硬度等进行了表征。结果表明,不同喷涂工艺下涂层的相组成均为γ′-Ni_3Al、β-NiAl和γ-Ni固溶体。低压等离子和超音速火焰喷涂的涂层致密且孔隙率低,其中超音速火焰喷涂的涂层孔隙率低于1%。低压等离子和低温超音速火焰喷涂的涂层氧含量很低,控制在0.3%~0.6%的范围。综合来说,低温超音速火焰喷涂工艺制备的涂层结构致密,孔隙率和氧含量很低。该工艺是沉积NiCoCrAlYTa涂层的首选。     

微束等离子喷涂羟基磷灰石涂层相结构的微拉曼光谱研究

羟基磷灰石(Hydroxyapatite,HA)涂层以其优异的生物相容性和骨传导性在生物医疗领域得到了广泛应用。然而,HA涂层的生物性能与其组织结构密切相关。本研究采用微束等离子喷涂技术,在Ti-6Al-4V基体上制备HA扁平粒子及HA涂层。采用扫描电镜(SEM)分别对原始HA粉末、HA扁平粒子表面和HA涂层截面的形貌进行了观察。通过微拉曼光谱对扁平粒子和涂层截面微区的相结构进行分析,得到磷酸基团(PO_4~(3-))及羟基基团(OH~-)在所选定区域的信息,对900～1 000 cm~(-1)频率范围的内的微拉曼光谱进行分峰拟合,获得了微束等离子喷涂HA扁平粒子表面相分布情况以及HA涂层沿厚度方向相结构的变化。结果表明,单个HA扁平粒子以非晶相为主,而在涂层中,靠近基体部分的相组成以非晶相及分解相(β-TCP)为主,仅包含少量HA晶体相,随着离涂层与基体界面距离的增加,非晶相及分解相含量逐渐减少,HA相增多,在近涂层表面非晶相和分解相(β-TCP)略有增加。     

喷涂功率对碳/碳复合材料表面羟基磷灰石涂层的影响

采用等离子喷涂技术在碳/碳复合材料表面制备了羟基磷灰石(HA)涂层,采用电子拉伸机和自制装置测定了不同喷涂功率下涂层与基体的抗剪强度,采用扫描电镜观察了涂层表面、剪切断裂表面的形貌,采用电子探针分析了试样截面的形貌和成分线分布.结果表明:随着喷涂功率的增加,涂层中HA颗粒的熔化程度和涂层与基体的抗剪强度均增加,涂层与基体的界面属于机械结合,其剪切断裂的形式主要有界面失效和涂层内部失效两种.     

等离子喷涂羟基磷灰石涂层的相组成及其结构

研究纯钛表面羟基磷灰石(HA)涂层的相组成及其微观结构,为涂层性能与制备工艺优化提供依据.采用等离子喷涂法制备HA涂层,用X射线衍射仪和透射电子显微镜进行相细成与微观结构的表征.研究表明:涂层主要由晶相HA、非晶相和分解相组成,随喷涂功率的提高,非晶化加剧,CaO含量提高;在TEM下观察到HA晶体与非晶体共存区、HA与磷酸三钙徽晶的共存区,以及HA与Ti的反应产物CaTi03;除工艺原因外,羟基磷灰石复杂的结构和混合键的结合也是其形成非晶态的主要原因.     

Ni-Cr2O3复合等离子喷涂层热处理改性前后的结构及性能

等离子喷涂层经热处理后可进一步改进其结构及性能,以往对其改性机理研究不多。采用等离子喷涂技术在20钢表面制备了Ni-Cr2O3复合涂层,经500℃、6 h热处理后随炉冷却。通过金相显微分析、X射线衍射、盐雾腐蚀、电化学试验等方法,对比研究了热处理前后Ni-Cr2O3复合涂层的组织形貌、相组成以及耐蚀性的变化。结果表明:Ni-Cr2O3复合涂层热处理前后物相组成未发生改变,经热处理后,孔隙率减小,组织更致密,耐蚀性大幅提高。     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Effect of Permeable Crystalline Material on Steel Reinforcement Corrosion of Concrete

Permeable crystalline materialcan permeate into pores and cracks of concrete and catalyze the reaction between Ca(OH) 2and unhydrated cement to generate a great quantity needle non-soluble crystals, which can stop up the pores and cracks of concrete, and increase the impermeability of concrete. This paper reported the results of a study conducted to evaluate steel reinforcement corrosion of concrete specimens uncoated and coated with permeable crystalline material as well as mixed with the permeable crystalline material. The properties evaluated for corrosion test were water impermeability, water absorption, compressive strength and potential. The results of water impermeability, water absorption, compressive strength clearly showed that the permeable crystalline material could prohibit water, any soluble salts and moisture from penetrating the concrete to cause corrosion, leaking, and other problems, and it did increase the compressive strength, which was favorable for protection of corrosion of reinforcing steel. Moreover, it was concluded from the potential-time curve that the steel reinforcement of uncoated specimen was in the state of activation whereas that of other specimens coated and mixed with the permeable crystalline material was in the state of inactivation. Above all, it was indicated that the permeable crystalline materialis very effective to protect the steel reinforcement of concrete from corrosion.     

The Research and Application About "Dry Peeling Off" Technology for Airplane Surface Paint Layer

In this paper, the principle of spurting take off lacquer were introduced; and with orthogonal method the unsaturate polyester was prepared ;it was easy to peel airplane paint layer off with this material and equipment.     

Quality Study of Honeycomb Core Shaping Without Wax Stabilization

Sandwich panels utilizing honeycomb cores result in lightweight, high-strength units that are very rigid. Indeed, they give honeycomb panels the best strength-to-weight ratio of any construction type available. Conventionally, the wax is poured into the cell of the core to strengthen the structure and prevent the core from being crushed during milling. Much time and labor is required to wax, mill, and clean the cores. In this study, the process of pouring wax into the core was skipped. In other words, the cutter directly milled the core. Experiments showed that the compressive strength of the core produced without wax stabilization was only 3% lower than that of cores produced using the traditional method. In addition, the drum peel strengths of cores produced without wax stabilization were 38.4% higher than cores produced using the traditional method, in which residual wax seriously polluted the adhesive. It was also found that eliminating the wax process can reduce costs.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

In-process thermal treatment of polylactic acid in fused deposition modelling

Polylactic acid (PLA) is one of the most widely used open source fused filament fabrication materials due to its ease of extrusion, biodegradability, and mechanical strength. The mechanical strength of PLA largely depends on the proper growth of its semi-crystalline structure, which can be severely impaired by a low rate of crystallization, particularly in open source printers. This can be further aggravated by the non-uniform thermal distribution of heat that causes improper curing among the extruded beads of the printing material. As a result, PLA printed on open source printers does not achieve the best mechanical properties. This research, for the first time, proposes an additive-free solution implemented through a detailed set of experimentation to improve the curing rate through in-process temperature variations to cure the joints among the beads. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy is used to confirm the improvements in the bead joints. This work is conducted in two phases of experiments. In the first phase, a full factorial ANOVA is used to investigate various process parameters and the important variables are used in the second phase to print test specimens in four different sets.