X射线影像存储材料BaF_xCl_（2－x）Eu~（2＋）的制备及其热释发光和

本文采用了不同温度下两次烧结的新方法，制备了系列Ｘ射线影象存储材料ＢａＦ＿ｘＣｌ＿（２－ｘ）：Ｅｕ￣（２＋）（ｘ＝０．９０，０．９５，１．００，１．０５，１．１０１．１５）。通过改变Ｆ／Ｃｌ比值，研究了在Ｘ射线辐照后ＢａＦ＿ｘＣｌ＿（２－ｘ）：Ｅｕ￣（２＋）的热释发光性质，给出了热释发光峰的温度与缺陷种类的关系。最后，我们研究了ＢａＦ＿ｘＣｌ＿（２－ｘ）：Ｅｕ￣（２＋）的光激励发光性质，给出了Ｆ／Ｃｌ比值与光激励发光强度的关系。     

超负磁致伸缩晶体Sm—Fe,Sm—Dy—Fe和Sm—Dy—Fe—Al的研究

本文研究了轻稀土负磁致伸缩ＳｍＦｅｘ（１．４０≤ｘ≤１．９４），ＳｍｘＤｙ１－ｘＦｅｙ（０．８４≤ｘ≤０．９２，１．８０≤ｙ≤１．９０），Ｓｍ０．９０Ｄｙ０．１０（Ｆｅ０．９５Ａｌ０．０５）１．８０晶体的制备，热处理及磁学性能，发现ＳｍＦｅｘ合金的λ－ｘ曲线存在两个峰值，峰值的ｘ点热处理发生的变化有一定的规律性，还比较了热处理前后，Ｓｍ－Ｆｅ、Ｓｍ－Ｄｙ－Ｆｅ和Ｓｍ－Ｄｙ－Ｆｅ－Ａｌ的相组成对性能     

钕铁硼－铝镍钴粘结永磁的复合效应

本文比较系统地研究了钕铁硼－铝镍钴复合粘结永磁的复合效应，结果表明在塑料含量一定时ＮｄＦｅＢ－ＡｌＮｉＣｏ＿５复合永磁的剩余磁感应强度Ｂｒ随ＮｄＦｅＢ含量变化基本不变；剩用温度系数α＿（Ｂｒ）随ＮｄＦｅＢ含量增加而线性增大；内禀矫顽力＿ｊＨ＿ｃ，矫顽力＿ｂＨ＿ｃ，最大磁能积（ＢＨ）＿ｍ均随ＮｄＦｅＢ含量Ｘ增加呈指数函数增大，并具有下列数学关系式：＿ｊＨ＿ｃ＝１５０ｅ￣（４．１５ｘ）＋４４０，＿ｂＨ＿ｃ＝１４９ｅ￣（３．３７ｘ）＋４００，（ＢＨ）＿ｍ＝０．１７２ｅ￣（３．６１ｘ）＋０．４     

Sm8Fe83Si2C5Cu0.5Nb1.5非晶合金的晶化动力学

用差热分析（ＤＴＡ）,结合Ｘ射线衍射（ＸＲＤ）研究了Ｓｍ８Ｆｅ８３Ｓｉ２Ｃ５Ｃｕ０．５Ｎｂ１．５非晶合金的晶化动力学。结果表明：温度在０￣１０００℃范围内,该合金的晶化相为α－Ｆｅ和Ｓｍ２（ＦｅＳｉ）１７Ｃｘ,α－Ｆｅ相的晶化表观激活能力３４９．５３ｋＪ／ｍｏｌ,Ｓｍ２（ＦｅＳｉ）１７Ｃｘ的晶化表观激活能力３１６．１９ｋＪ／ｍｏｌ,两相在晶化初期激活能量小,随晶化量（ｘｃ）的增加激活能增大,当α－     

超负磁致伸缩晶体Sm－Fe、Sm－Dy－Fe和Sm－Dy－Fe－Al的研究

本文研究了轻稀土负磁致伸缩ＳｍＦｅ＿ｘ（１．４０＜ｘ＜１．９４），Ｓｍ＿ｘＤｙ＿（１－ｘ）Ｆｅ＿ｙ（０．８４＜ｘ＜０．９２．１．８０＜ｙ＜１．９０），Ｓｍ＿（０．９０）Ｄｙ＿（０．１０）（Ｆｅ＿（０．９５）Ａｌ＿（０．０５））＿（１．８０）晶体的制备、热处理及磁学性能，发现ＳｍＦｅ＿ｘ合金的λ－ｘ曲线存在两个峰值，峰值的ｘ点随热处理发生的变化有一定的规律性，还比较了热处理前后，Ｓｍ－Ｆｅ、Ｓｍ－Ｄｙ－Ｆｅ和Ｓｍ－Ｄｙ－Ｆｅ－Ａｌ的相组成对性能的影响。热处理用于改善磁致伸缩性能，并且制得了高磁致伸缩性能的ＳｍＦｅ＿２和（Ｓｍ，Ｄｙ）Ｆｅ＿２合金。     

4×155Mb／s频分复用（FDM）光纤通信系统的研究

报道了一个无故障工作时间大于２４小时的四路１５５Ｍｂ／ｓ频分复用（ＦＤＭ）光纤通信系统，实测系统误码率优于０×１０（－１４）。系统接收机包括解复用光滤波器，接收机灵敏度优于－３０ｄＢｍ（ＢＥＲ＝１×１０（－９），频道间距为０．１ｎｍ，四路ＦＤＭ信号－２０ｄＢ的总谱宽为０．７ｎｍ。系统采用国产ＤＦＢ激光器为光源，实际光纤传输距离１８ｋｍ。系统全部实现了脱离光学平台的模块化结构，在长期的系统实验中显示了优良的稳定性。这一成果为ＦＤＭ在光纤传输接入网中的进一步实用化开发铺平了道路。     

无Co混合导电型陶瓷透氧膜的制备和性质研究

首次合成了Ｓｒ１０－ｎ／２ＢｉｎＦｅ２０Ｏｍ（ｎ＝２，４，６，８，１０等）系列氧化物透氧膜，它们具有较高的透氧能力，其中，样品ｎ＝１０在１１００Ｋ时的透氧率为０．９０ｍｌ（ＳＴＤ）／（ｃｍ２·ｍｉｎ），比Ｓｒ１－ｘＢｉｘＦｅＯ３高约两倍．Ｓｒ１－ｘＢｉｘＦｅＯ３（ｘ＝０．１，０．３，０．５）系列的透氧率随Ｂｉ含量增加而增大．通过两个系列氧化物的ＸＲＤ和化学组成的对比，发现Ｂｉ离子含量和晶格空位浓度对透氧能力大小起决定性作用．     

NbCx-C三维网状纤维的制备

采用碳热还原法和不同的添加剂在温度为９７０￣１１２０℃,压力为０．１ＭＰａ的Ｎ２条件下,在石墨电阻炉内首次制备出ＮｂＣｘ（ｘ＝０．９８）－Ｃ三维网状纤维。三维网状纤维的直径为１２￣３８μｍ,网的环长为０．２２￣２．２ｍｍ,网孔径为７０￣７０１μｍ。本文详细研究了制备的工艺条件及相应的网状纤维的形貌。     

色散渐减光纤压缩光脉冲

利用色散补偿光纤（ＤＣＦ）及色散位移光纤（ＣＳＦ）压缩重复频率为２．５ＧＨｚ的增益开关量子阱ＤＦＢ半导体激光器出射的光脉冲，将光脉冲由５３．８ｐｓ压缩至２．５ｐｓ，而后利用色散渐减光纤将２．５ｐｓ的光脉冲进一步压缩至０．８３ｐｓ。     

Pb（Ni_（1／3）Nb_（2／3））O_3－PbZrO_3－PbTiO_3三

对Ｐｂ（Ｎｉ１／３Ｎｂ２／３Ｏ３－ＰｂＺｒＯ３－ＰｂＴｉＯ３，即ｘＰｂ（Ｎｉ１／３Ｎｂ２／３）Ｏ３－（１－ｘ）Ｐｂ（ＺｒδＴｉ１－δ）Ｏ３（０．２≤ｘ≤０．６，０．２≤δ≤０．５）三元系固溶体的压电性能进行了研究，结果表明材料压电活性较高的配方位于准同型相界（ＭＰＢ）附近，压电常数ｄ３１值可达２６０×１０－１２Ｃ／Ｎ．讨论了结构相变对压电性能的影响．     

卤化银多晶光纤传输CO2激光性能的研究

通过采用高真空熔炼、反应气氛下区域融熔和高真空石英安瓿内单晶生长等特殊工艺方法对卤化银原料进行提纯,并用热挤压成型方法制得卤化银光纤．本文研究了卤化银原料的提纯和光纤成型工艺对损耗的影响,研究结果表明,增加提纯次数可降低卤化银光纤预制棒的吸收系数．通过合理控制工艺参数,提纯后的卤化银原料制成的光纤预制棒,经ＣＯ_２激光量热计法测量在１０．６μｍ处的吸收系数＜５×１０^－4ｃｍ^－１,热挤压成型的光纤在１０．６μｍ处的损耗为０.３～０.５ｄＢ／ｍ,直径φ１０ｍｍ、长度１．６４ｍ的光纤可传输ＣＯ_２激光功率＞２０Ｗ．     

Experimental evaluation of a hollow glass fiber

Very high interest in making a low-loss fiber for the infrared has been stimulated by important applications in optical communication, surgery, cutting, welding, and heat treatment. The leaky waveguide is one of the most promising types of future fiber in the infrared region where low-loss materials are not available or not suitable for making fibers (i.e., CO2 laser light lambda = 10.6 microm). In this paper a comparative model of a He-Ne laser beam and an oxide glass leaky hollow fiber for a CO2 laser light beam and a chalcogenide glass leaky hollow fiber are studied. Measurements of attenuation, dependence of output power on diameter and angle, and the angular dependence of output angle vs input angle were made. The experimental data were compared with theoretical calculations, and the critical value of the wall thickness for minimum attenuation is given.     

卤化银光纤原料的超提纯

高纯原料的制备是制造高品质光纤最重要的环节,本文采用氯气氛下水平区熔法生长单晶的提纯方法对卤化银原料进行超提纯．区域熔融提纯后的卤化银原料红外吸收光谱测量显示在800～4000cm^－1范围内吸收随波长的增加而降低．经CO₂激光量热计法测量提纯后的卤化银原料在10．6μm处的吸收系数为5×10^－4Cm^－1,较提纯前降低两个数量级,制成的光纤传输损耗03～0．5dB／m     

Silver-coated hollow-glass waveguide for applications at 800 nm

A 250-microm-bore size and 50-cm-length hollow-glass waveguide (HGW) coated with a thin film of silver has been used to transport laser pulses at 800 nm from a Ti:sapphire oscillator. The silver film is deposited by a liquid-phase process. The measured transmission of this silver-coated HGW is 95%, which is considerably higher than the transmission of HGWs with no coating, as reported by other groups. The image of the output beam taken at different distances from the fiber output shows that a single HE11 mode couples to free-space modes from the exit of the fiber. Considerable spectral broadening can be obtained with high-intensity femtosecond pulse when this waveguide is filled with argon. This HGW can be used for such applications as beam transport and optical-pulse compression.     

反应氯气气氛下卤化银光纤原料的超提纯

采用反应氯气气氛下水平区域熔融生长单晶的方法对卤化银原料进行超提纯,反应氯气气氛是由裂解低沸点碳氯化合物得到;化合物的通式为ＣＨ_ｎＣｌ_４－ｎ(ｎ＝０,１,２)．提纯的温度为４５０~５００℃,温区移动速度为０．２~０．８ｍｍ/ｍｉｎ;载流气体Ａｒ的流量为８０~１６０ｍＬ/ｍｉｎ．提纯后的卤化银原料红外吸收光谱显示,在４０００~８００ｃｍ^－１(２．５~１２．５μｍ)区域内的吸收随波长的增加而降低,中红外４０００~６００ｃｍ^－１(２．５~１６μｍ)区域是卤化银材料最佳的传输波段．用此原料制成的光纤可传输３．３~１６μｍ中红外光谱;传输１０．６μｍＣＯ_２激光的损耗为０．３~０．５ｄＢ/ｍ．     

Characterization and use of an optical fiber interferometer for measurement of the electric wind

An optical fiber interferometer of the Mach-Zehnder type has proved to be a convenient and accurate method for measuring the electric wind in the active region of a corona discharge. The technique relies on the cooling effect of the wind on a small heated region of one arm of the interferometer, which has been remotely heated with an infrared CO(2) laser beam. Wind speeds of up to 5.5 m s(-1) have been measured near the generation region, and by the use of a mesh electrode, the wind has been detected on the axis up to 0.5 m away from the gap. A number of characterization experiments that show the interferometer to be a useful diagnostic tool in the quantitative analysis of the CO(2) laser beam have also been carried out, and good agreement between experimental results and theoretical calculations based on a simple heat-power balance equation for the fiber exists.     

Vibrational spectra and surface-enhanced vibrational spectra of 1-nitropyrene

The present report on the vibrational spectra of 1-nitropyrene (1NP) describes the infrared and Raman spectra; their interpretation is aided by local density functional theory (DFT) calculations at the B3LYP/6-311G(d, p) level of theory and by the surface-enhanced vibrational spectra (SEVS) with the final objective of trace organic analytical applications. The surface-enhanced Raman scattering (SERS) on silver island films and mixed silver/gold island films was investigated with several laser lines in the visible region. Surface-enhanced infrared absorption (SEIRA) was attempted on silver and gold island films. The interface of the organic 1-NP with smooth metal surfaces of silver and copper was also probed using reflection-absorption infrared (RAIRS) spectra that, in conjunction with the transmission spectra, allow one to extract the molecular orientation in vacuum evaporated thin solid films. Chemical adsorption of 1-NP on silver and further photochemical decomposition of the 1-NP-metal adsorbates was detected with all visible laser lines. Resonance Raman scattering (RRS) using UV-laser excitation at 325 nm was also recorded.     

Delivery of 10-MW Nd:YAG laser pulses by large-core optical fibers: dependence of the laser-intensity profile on beam propagation

A large-core multimode optical fiber of a few meters length is studied as a 10-MW beam delivery system for a 15-ns pulsed Nd:YAG laser. A laser-to-fiber vacuum coupler is used to inhibit air breakdown and reduce the probability of dielectric breakdown on the fiber front surface. Laser-induced damage inside the fiber core is observed behind the fiber front surface. An explanation based on a high power density is illustrated by a ray trace. Damaged spots and measurements of fiber output energies are reported for two laser beam distributions: a flat-hat type and a near-Gaussian type. Experiments have been performed to deliver a 100-pulse mean energy between 100 and 230 mJ without catastrophic damage.     

Recording of long-period gratings in special single-mode fibers by a CO2 laser

The paper deals with the fabrication of long-period gratings (LPG) in special optical fibers with an inverted parabolic-index profile of the cladding by periodically exposing the fibers to radiation of a high-power CO₂ laser. Details on the fiber fabrication and preparation of LPGs with a period of about 1 mm in the fibers are presented. The fabricated LPGs were evaluated on the basis of their transmission spectra determined by measuring the output spectral density of the fiber with the LPGs. It is shown that the position of the band and its strength depend on the laser beam velocity, beam power and the interaction time of radiation with the fiber.     

Diode-laser-pumped tunable 896-939.5-nm neodymium-doped fiber laser with 43-mW output power

A diode-laser-pumped neodymium-doped fiber laser is presented. For a launched pump power of 85 mW, the fiber laser had a cw output power of 43 mW, which is approximately an order of magnitude greater output power than any previously reported diode-pumped neodymium fiber laser operating on the(4)F(3/2)-(4)I(9/2) transition, which covers the 900-950-nm region. The fiber laser had a threshold power of 10 mW and a slope efficiency of 58% with respect to launched pump power. Tuning with a diffraction grating was obtained from 896 to 937 nm with narrow-band output powers as high as 32 mW. Emission was also obtained at 939.5 nm with use of a fiber Bragg grating as the output reflector.