Microstructures, densification and mechanical properties of TiC–Al2O3–Al composite by field-activated combustion synthesis

Dense TiC–Al₂O₃–Al composite was prepared with Al, C and TiO₂ powders by means of electric field-activated combustion synthesis and infiltration of the molten metal (here Al) into the synthesized TiC–Al₂O₃ ceramic. An external electric field can effectively improve the adiabatic combustion temperature of the reactive system and overcome the thermodynamic limitation of reaction with x < 10 mol. Thereby, it can induce a self-sustaining combustion synthesis process. During the formation of Al₂O₃–TiC–Al composite, Al is molten first, and reacted with TiO₂ to form Al₂O₃, followed by the formation of TiC through the reaction between the displaced Ti and C. Highly dense TiC–Al₂O₃–Al with relative density of up to 92.5% was directly fabricated with the application of a 14 mol excess Al content and a 25 V cm⁻¹ field strength, in which TiC and Al₂O₃ particles possess fine-structured sizes of 0.2–1.0 μm, with uniform distribution in metal Al. The hardness, bending strength and fracture toughness of the synthesized TiC–Al₂O₃–Al composite are 56.5 GPa, 531 MPa and 10.96 MPa m^1/2, respectively.     

Improvements in mechanical properties of TiB2 ceramics tool materials by the dispersion of Al2O3 particles

TiB₂–Al₂O₃ composites with Ni–Mo as sintering aid have been fabricated by a hot-press technique at a lower temperature of 1530 °C for 1 h, and the mechanical properties and microstructure were investigated. The microstructure consists of dispersed Al₂O₃ particles in a fine-grained TiB₂ matrix. The addition of Al₂O₃ increases the fracture toughness up to 6.02 MPa m^1/2 at an amount of 40 vol.% Al₂O₃ and the flexural strength up to 913.86 MPa at an amount of 10 vol.% Al₂O₃. The improved flexural strength of the composites is a result of higher density than that of monolithic TiB₂. The increase of fracture toughness is a result of crack bridging by the metal grains on the boundaries, and crack deflection by weak grain boundaries due to the bad wetting characters between Ni–Mo and Al₂O₃.     

Fe/Al2O3复合材料的制备和性能

用石墨埋烧方法制备Fe/Al₂O₃复合材料,对其力学性能和微观结构进行了分析。结果表明:Fe/Al₂O₃复合材料的弯曲强度与断裂韧性均随Al₂O₃含量的升高先升高后降低,当Al₂O₃含量（质量分数）为70%时,其弯曲强度与断裂韧性分别达到602.49 MPa和9.33 MPa·m¹/2,其硬度随Al₂O₃含量先降低后升高。在烧结过程中在Fe颗粒周围形成一种成分为FeO与FeAl₂O₄的壳体,在壳体与Fe颗粒之间存在微裂纹缺陷。壳体的形成和壳体与金属颗粒间的微裂纹钝化了外部应力,从而提高了复合材料的韧性。     

ZrO_2增韧Al_2O_3陶瓷的力学性能和增韧机制

对通过热压烧结法制备的3种陶瓷99.5vol%Al2O3(AD995)、ZrO2(15vol%)/Al2O3和ZrO2(25vol%)/Al2O3的力学性能和增韧机制进行了实验和理论研究。基于复合材料细观力学理论并考虑ZrO2的相变特性,建立了描述ZrO2/Al2O3陶瓷力学性能的本构模型。结果表明:ZrO2的加入细化了基体Al2O3晶粒,ZrO2/Al2O3陶瓷的致密性得到提高;3种陶瓷试件的破坏呈现小变形到脆性破坏的特点,压缩加载下试件应力-应变曲线近似为线性关系;AD995陶瓷的断裂韧性为5.65 MPa·m1/2,ZrO2(25vol%)/Al2O3陶瓷的断裂韧性为8.42 MPa·m1/2,提高了近50%;随ZrO2增韧相含量的增加,ZrO2/Al2O3陶瓷的弹性模量降低而断裂韧性增加,这一变化趋势与实验结果有良好的一致性。     

Study of the densification of a nanostructured composite powder: Part 1: Effect of compaction pressure and reinforcement addition

Al/Al₂O₃ composite coating was prepared by plasma spraying and characterized by XRD and SEM. Some thermal–mechanical properties of the composite coating including thermal diffusivity, microhardness, fracture toughness and sliding wear rate were measured. The results showed that the Al/Al₂O₃ composite coating, compared with Al₂O₃ coating, exhibits denser structure and developed splat interface. The coexistence of Al metal phase and Al₂O₃ ceramic phase effectively increased the fracture toughness and thermal diffusivity of composite coating, in spite of the slight decrease in microhardness. Furthermore, the wear resistance of Al/Al₂O₃ composite coating is superior to that of Al₂O₃ coating.     

Processing, microstructure and properties of C40 Mo(Si,Al)2/Al2O3 composites

The C40 Mo(Si_0.75Al_0.25)₂/Al₂O₃ composites were prepared by spark plasma sintering (SPS) of mechanically alloyed (MA) powders. The Mo(Si_0.75Al_0.25)₂/0–20 vol.% Al₂O₃ materials, showing micron and submicron composite structure, possess a hardness of 13.9–14.6 GPa but a poor toughness of 1.78–1.80 MPa m^1/2. The addition of 30 vol.% Al₂O₃ leads to the formation of the micron C40 Mo(Si_0.75Al_0.25)₂/Al₂O₃ composite with an intergranular distribution of Al₂O₃, that results in a drop of the hardness to 10.2 GPa and an improvement of the toughness to 3.67 MPa m^1/2. The transition of the cleavage facets to the intergranular fracture with the addition of Al₂O₃ is assumed as the main toughening mechanism.     

Characterization of the Reaction Products That Develop in the Processing of Al2O3/BaZrO3 Laminated Composites

The absence of a chemical reaction at an interface is conventionally thought to be an important criterion in producing a tough ceramic matrix composite (CMC). As a result of this criterion, interphases in CMCs were chosen on the basis of their chemical reactivity. A weak interface results in crack deflection, crack bridging, and, in fiber-reinforced ceramics, fiber pullout, resulting in an increased fracture toughness. In this paper, we present microstructural observations on alumina (Al₂O₃)–barium zirconate (BaZrO₃) laminated composites wherein the reaction products that develop during processing resulted in sharp interfaces and appear to be weak enough to deflect cracks. These in situ reaction products in Al₂O₃–BaZrO₃ laminated composites were characterized with the use of a scanning electron microscope, an electron microprobe, and a transmission electron microscope. The phases that develop, ZrO₂, BaO·Al₂O₃, and BaO·6 Al₂O₃, produced sharp interfaces and are arranged in a sequence that could be predicted by using information from the phase diagram.     

Crystal morphology and growth mechanism of reinforcements synthesized by direct melt reaction in the system Al–Zr–O

In-situ Al₃Zr and Al₂O₃ particulates reinforced aluminum matrix composites were fabricated by the direct melt reaction (DMR) technique in the system Al–Zr–O. Microstructures of the composites and crystal morphology of in-situ formed Al₃Zr and Al₂O₃ particulates were analyzed by scanning-electron microscope (SEM) and transmission electron microscope (TEM). Results indicated that in-situ formed Al₃Zr and Al₂O₃ particles were finer and well distributed in aluminum matrix. Al₃Zr particulates with a tetragonal structure are mainly in the shape of polyhedron. A few of them are rectangular. The length/width ratio of the rectangular Al₃Zr is less than 2.0 and the maximum size is 4 μm. In addition, submicro Al₂O₃ particles with a hexagonal structure were also found in this system. Furthermore, it is found that twin may appear in the Al₃Zr crystal. The twin plane is (1 ). The twinning direction is [2 1].     

Al-TiO2-B2O3-C系XD合成铝基复合材料的反应机理及力学性能

研究了Al-TiO2-B2O3-C反应系XD合成铝基复合材料的反应机理.结果表明在Al-TiO2-B2O3-C系中,当B2O3/TiO2摩尔比=0.5,C/TiO2摩尔比=0时,TiO2和B2O3分别与Al结合生成热力学稳定的Al2O3和活性Ti原子、B原子,B原子和Ti原子分别穿过各自反应层结合生成热力学稳定的TiB2,过剩的Ti原子则与Al结合生成棒状物Al3Ti;加入碳粉后,Ti原子将优先与C和C与Al的化合物Al4C3反应生成TiC,Al3Ti逐渐减少,在C/TiO2摩尔比为0.5时,Al3Ti相基本消失,力学性能得到改善,其拉伸强度和延伸率分别从266MPa和3%增加到315MPa和7%.     

SiCW对反应烧结多孔Al2TiO5-SiCW 复合材料的影响

以γ-AlOOH、TiO₂和SiC_w为原料,通过反应烧结制备了多孔Al₂TiO₅-SiC_w复合材料,研究了SiC_w对Al₂TiO₅-SiC_w复合材料物相、微观组织结构、孔隙率和抗压强度的影响。结果表明: 反应产物中主要物相有Al₂TiO₅、Al₆Si₂O₁₃、TiC和SiO₂。由于晶须分解速度快,SiC_w可全部与TiO₂反应生成TiC和SiO₂。添加SiC_w,一方面显著细化了Al₂TiO₅基复合材料的微观组织,生成的细小规则的TiC晶粒和存在于Al₂TiO₅晶界处的Al₆Si₂O₁₃有利于抑制Al₂TiO₅晶粒长大,提高其抗压强度。另一方面,因为SiC_w改变了原料中颗粒之间的堆积方式,使孔径增大、孔隙率显著提高。生成的一定量的SiO₂对晶粒产生黏结,使得Al₂TiO₅基复合材料的孔洞骨架密实,提高了抗压强度,但当SiC_w加入量多时,由于出现较多的玻璃相,会降低抗压强度。     

纤维预热温度对连续Al2O3f/Al复合材料力学性能的影响

选用Nextel610型Al₂O₃纤维为增强体、ZL210A连续氧化铝合金为基体,采用真空压力浸渗法制备纤维增强铝基复合材料(Al₂O_3f/Al),纤维的体积分数为40%,预热温度分别为500、530、560和600℃,研究了纤维预热温度对Al₂O_3f/Al复合材料的微观组织、纤维损伤和力学性能的影响。结果表明：随着纤维预热温度的提高复合材料的致密度随之提高,最大达到99.2%,材料的组织缺陷最少,纤维的分布均匀;随着纤维预热温度的提高从复合材料中萃取出来的Al₂O₃纤维的拉伸强度不断降低,纤维预热温度为600℃的复合材料中Al₂O₃纤维的拉伸强度仅为1150 MPa,纤维表面粗糙,有大尺寸附着物。纤维的预热温度对Al₂O_3f/Al复合材料的拉伸强度有显著的影响。预热温度为500、530、560和600℃的复合材料其拉伸强度分别对应于298、465、498和452 MPa。组织缺陷、纤维损伤和界面结合强度,是影响连续Al₂O_3f/Al复合材料强度的主要因素。     

Ionic Conductivity and Mechanical Properties of Post-HIPed Cubic Zirconia/Alumina Composites

8 mol.% yttria-doped cubic zirconia (8Y-CSZ)/AI₂O₃ composites containing 0-30 vol.% Al₂O₃ particles were fabricated by sintering, followed by hot isostatic pressing (post-HIPing). All composites were densified to at least 99·5% of the theoretical density by post-HIPing. The bending strength of composites sintered at 1500°C in air was independent of A1₂O₃ content, but a significant improvement in the bending strength was achieved by the post-HIPing technique. The bending strength and the fracture toughness of the HIPed composites increased with increasing A1₂O₃ content. Ionic conductivity of the composites was evaluated and the total, lattice, and grain boundary conductivities slightly decreased with increasing A1₂O₃ content. The HIPed composites containing up to 20 vol.% A1₂0₃ appear to be suitable candidate materials as electrolyte for solid oxygen fuel cell.     

SiC对反应烧结多孔Al2TiO5的物相及组织性能影响

本研究以γ-AlOOH、TiO₂和SiC为原料, 通过无压反应烧结制备了Al₂TiO₅多孔材料, 分析比较了SiC粒度和含量对合成产物的物相组成、显微组织、抗压强度、孔隙率和孔径分布的影响。结果表明: 反应产物的物相组成为Al₂TiO₅、Al₆Si2O₁₃、TiC、SiO₂和Al₂O₃, 还有少量未反应的TiO₂。SiC与TiO₂反应生成TiC和SiO₂, TiC颗粒弥散分布于多孔材料壁面或者骨架中, 而SiO₂进一步与γ-AlOOH分解出的Al2O3反应生成Al₆Si₂O₁₃晶须, 晶须交错分布于Al₂TiO₅颗粒之间或者孔洞中, 与TiC颗粒一起提高复合材料的抗压强度, 特别是采用小粒径SiC时, 对抗压强度的改善效果更加显著; 添加大粒径SiC后, 改变原有颗粒堆积状态, 可提高复合材料的孔隙率。但当SiC含量超过5wt%时, 因为生成较多低熔点的SiO₂, 部分填充于多孔材料的孔隙中, 部分则分布于Al₂TiO₅晶粒之间, 既减小孔隙率, 又降低晶粒间结合强度和试样的抗压强度。     

片状纳米Al2O3/环氧树脂复合材料的制备及性能

采用水热法制备片状纳米Al₂O₃,经过偶联剂改性后与环氧树脂复合,通过溶液混合法制备了不同填充量的片状纳米Al₂O₃/环氧树脂复合材料,研究了片状纳米Al₂O₃用量对片状纳米Al₂O₃/环氧树脂复合材料介电性能和热性能的影响,利用SEM对复合材料的断口形貌进行了表征。结果表明: 片状纳米Al₂O₃在环氧树脂基体中分散良好;随着片状纳米Al₂O₃填充量的增加,复合材料的起始热分解温度升高、介电强度增大,当片状纳米Al₂O₃的填充量为7wt%时,复合材料的介电强度为 29.58 kV/mm,比纯环氧树脂的介电强度提高了30%;复合材料的介电常数(3.8~4.5)和介电损耗(0.015)比纯环氧树脂稍有增大,但仍维持在较好的介电性能范围内。     

反应烧结B4C/Al2O3复合陶瓷的装甲防护性能研究

以B₂O₃、Al、石墨和B₄C粉体为原料, 采用反应-热压烧结工艺在1800℃/35 MPa的烧结条件下制备了致密的碳化硼基复相陶瓷, 对复相陶瓷的显微组织、物相组成、硬度、抗弯强度以及断裂韧性进行了观察与测试, 采用7.62 mm口径的穿甲弹分别对约束状态下和自由状态下的复相陶瓷靶板进行了剩余穿深试验(DOP), 并以AZ陶瓷和B₄C陶瓷为对比靶板, 根据剩余穿深结果计算了各自的防护系数。结果表明, 复相陶瓷的主要成分为B₄C和Al₂O₃, 其中主相B₄C约占70wt%, 第二相Al₂O₃约占30wt%, 由Al-B-O共同构成的复杂中间相填充在主相与第二相之间; 复相陶瓷的密度、硬度、抗弯强度和断裂韧性分别为2.82 g/cm³, 41.5 GPa, 380 MPa和3.9 MPa•m^1/2, 其中断裂韧性比纯碳化硼陶瓷提高了85.7%; 复相陶瓷的防护系数为7.34, 比AZ陶瓷和碳化硼陶瓷分别提高了11%和70%; 在约束状态下, 各个样品的防护系数比自由状态均提高10%。     

Improvement of the tensile strength of Al18B4O33w/Al composite at elevated temperatures by change of interfacial state

In general, it is very difficult to obtain obviously reinforced effect in discontinuously reinforced aluminum matrix composites at the temperature above 400 °C. In the present study, we report an effective method to improve the high-temperature tensile strength of Al₁₈B₄O₃₃w/Al composite by change of interfacial state. The pure aluminum matrix composites reinforced by Al₁₈B₄O₃₃w with different ZnAl₂O₄ coating contents were fabricated by squeeze casting. The results indicate that ZnAl₂O₄ coating of the whiskers can effectively improve the high-temperature tensile strength of Al₁₈B₄O₃₃w/Al composite, although the tensile strength of the composite decreases with increasing the tensile temperature. On the basis of fractograph analysis, the fracture mechanism of the composites at elevated temperatures was investigated.     

Bi2O3助熔剂对CaO-B2O3-SiO2/Al2O3玻璃陶瓷复合材料性能的影响

以CaO-B₂O₃-SiO₂(CBS)玻璃粉体和Al₂O₃陶瓷粉体为原料,通过在CBS与Al₂O₃的质量比固定为50:50的玻璃-陶瓷复合材料中添加适量的Bi₂O₃作为烧结助熔剂,探讨了Bi₂O₃助熔剂对CBS/Al₂O₃复合材料的烧结性能、介电性能、抗弯强度和热膨胀系数的影响规律.研究表明:Bi₂O₃助熔剂能通过降低CBS玻璃的转变温度和黏度促进CBS/Al₂O₃复合材料的致密化进程,于880 ℃下烧结即能获得结构较致密、气孔较少的CBS/Al₂O₃复合材料.然而,过量添加Bi₂O₃将使玻璃的黏度过低,从而恶化CBS/Al₂O₃复合材料的烧结性能、介电性能及抗弯强度.当Bi₂O₃的添加量为CBS/Al₂O₃复合材料的1.5wt%时,于880 ℃下烧结即能获得最为致密的CBS/Al₂O₃复合材料,密度为2.82 g·cm^-3,这一材料具有良好的介电性能(介电常数为7.21,介电损耗为1.06×10^-3),抗弯强度为190.34 MPa,0~300 ℃的热膨胀系数为3.52×10^-6 K^-1.     

三维网络结构Al2O3陶瓷/高铬铸铁复合材料干摩擦磨损性能

采用往复式滑动摩擦磨损（SRV）试验机研究了高铬铸铁及三维网络结构Al₂O₃陶瓷增强高铬铸铁复合材料的干摩擦磨损性能,测量了高铬铸铁和Al₂O₃陶瓷/高铬铸铁复合材料在不同摩擦频率及载荷下的摩擦系数和磨损率;用扫描电镜观察磨损表面形貌,并分析了三维网络Al₂O₃陶瓷对复合材料磨损机制的影响。结果表明：陶瓷Al₂O₃与高铬铸铁基体之间具有良好的界面结合,复合材料的摩擦系数随摩擦频率和载荷的变化保持稳定,耐磨性远优于高铬铸铁,而且随着摩擦频率和载荷的增加,Al₂O₃陶瓷/高铬铸铁复合材料的抗磨损性能明显提高,这是由于复合材料中Al₂O₃与高铬铸铁相之间三维空间结构和良好的界面结合有利于摩擦载荷的传递;三维Al₂O₃陶瓷骨架在磨损表面形成硬的网络突体并起承载作用,能有效保护金属基体;磨损机制为氧化磨损及磨粒磨损共同作用。     

原位引入BN-SiC燃烧合成Si3N4-BN-SiC复合材料

Si₃N₄-BN-SiC复合材料以其良好的力学性能和抗氧化性能而具有良好的工程应用前景。本研究以Si、Si₃N₄稀释剂、B₄C和Y₂O₃为原料, 采用燃烧合成法成功制备了Si₃N₄-BN-SiC复合材料。通过Si、B₄C和N₂气之间的反应, 在Si₃N₄陶瓷中原位引入BN和SiC, 制备的Si₃N₄-BN-SiC复合材料由长棒状的β-Si₃N₄和空心球形复合材料组成。实验研究了空心球微结构的形成机理, 结果表明, 生成的SiC、BN颗粒及玻璃相覆盖在原料颗粒上, 当原料颗粒反应完全时, 形成空心球形微结构。并进一步研究了B₄C含量对Si₃N₄-BN-SiC复合材料力学性能的影响。原位引入SiC和BN在一定程度上可以提高复合材料的力学性能。当B₄C添加量为质量分数0~20%时, 获得了抗弯强度为28~144 MPa、断裂韧性为0.6~2.3 MPa·m ^1/2, 杨氏模量为17.4~54.5 GPa, 孔隙率为37.7%~51.8%的Si₃N₄-BN-SiC复合材料。     

Al2O3纤维对SiO2基陶瓷型芯的烧缩阻滞

向SiO₂基体粉料中添加Al₂O₃纤维,采用热压注法制备Al₂O₃/SiO₂陶瓷型芯。分析Al₂O₃纤维含量对陶瓷型芯性能的影响。研究结果表明：Al₂O₃纤维含量对Al₂O₃/SiO₂陶瓷型芯的线收缩率、体积密度和抗弯强度均有较大的影响。当Al₂O₃纤维含量大于1wt%时,Al₂O₃/SiO₂陶瓷型芯的线收缩率大幅度降低,稳定在0.335%左右,体积密度随之降低,稳定在1.790 g · cm^-3左右;当Al₂O₃纤维含量为1wt%时,陶瓷型芯抗弯强度达最大值20.48 MPa。分析了Al₂O₃纤维对Al₂O₃/SiO₂陶瓷型芯烧结收缩的阻滞作用机制。