微波ECR-CVD法制备a-C:F:H膜的红外吸收及其光学带隙

改变CHF3 CH4 流量比R =[CHF3] ([CHF3]+[CH4 ]) ,采用微波电子回旋共振等离子体化学气相沉积 (MWECR CVD)方法沉积a C :F :H薄膜。a C :F :H薄膜的结构和光学带隙使用傅立叶变换红外光谱和紫外 可见光谱来表征。红外结果表明 ,在低流量比R(R <6 4 % )下 ,薄膜的红外特征结构主要以 CF(10 6 0cm- 1 ) , CF2(112 0cm- 1 )以及 CHx(2 80 0～ 30 0 0cm- 1 )的伸缩振动为主 ;在高流量比R(R >6 4 % )下 ,薄膜表现为类聚四氟乙烯(PTFE)的结构特征 ,典型的红外特征峰是位于 12 2 0cm- 1 处的 -CF2 反对称伸缩振动。薄膜的光学带隙Eg 随流量比R的变化表现为先降后升。进一步研究表明 ,薄膜中的H和F浓度调制着薄膜的CC共轭双键结构 ,使光学带隙Eg 从 2 37到 3 3之间变化     

沉积参数对化学气相沉积纳米金刚石薄膜的影响

用强电流直流伸展电弧化学气相沉积金刚石薄膜装置,在CH4-Ar和CH4-H2-Ar气氛中沉积了纳米金刚石薄膜,研究了沉积气氛中H2加入量和沉积压力对金刚石薄膜显微组织和生长机制的影响.沉积气氛中H2含量对金刚石薄膜的表面形貌、晶粒尺寸和生长速度有显著影响,随着H2含量增加,金刚石晶粒尺寸增大,薄膜生长速度提高.在1%CH4-Ar气氛中沉积的纳米金刚石薄膜,晶粒尺寸细小,薄膜表面形貌光滑平整.在1%CH4-少量H2-Ar气氛中沉积的金刚石薄膜,晶粒尺寸小于100nm,薄膜表面形貌较平整.随着沉积压力提高,金刚石薄膜的生长速度增大.用激光Ram an对金刚石薄膜进行了表征.     

低温生长硅基碳化硅薄膜研究

在 8 5 0℃的低温下 ,在Si( 10 0 )衬底上生长了 3C SiC薄膜 ,气源为SiH4和C2 H4混合气体。用X射线衍射、X射线光电子能谱和傅立叶红外吸收谱分析了薄膜的晶体结构、组分以及键能随深度的变化。研究表明薄膜为富硅的 3C SiC结晶层 ,其中的Si/C比约为 1 2。     

以SiCl4为源气体用PECVD技术低温快速生长多晶硅薄膜

报道了以SiCl4和H2为气源,用等离子体增强化学气相沉积技术,在小于300℃的低温下快速生长多晶硅薄膜.实验发现, 生长速率强烈依赖于放电功率、H2/SiCl4流量比和衬底温度, 而薄膜的晶化度只依赖于放电功率和H2/SiCl4流量比,与衬底温度的关系不大.通过控制和选择工艺条件,我们获得了生长速率高达0.35nm/s,晶化度高于75%的多晶硅薄膜.薄膜的暗电导率和光电导率分别达到10-4S-1·cm-1和10-3S-1·cm-1.     

甩胶喷雾热分解法制备ITO薄膜及光电性能研究

按In:Sn(物质的量比)=9:1,InCl3·4H2O和SnCl4·5H2O为前驱物,采用自制甩胶喷雾热分解制备薄膜装置在普通玻璃衬底上沉积了ITO薄膜,结果表明,采用自制甩胶喷雾热分解制备薄膜新装置成功制备出ITO薄膜。该装置结构简单、操作方便。制备ITO薄膜优化条件为:甩胶转速800r/min、衬底温度250℃、退火温度450℃、载气为空气、流量为7L/min、液体雾化速度0.2ml/min、雾粒速度3.5m/s。薄膜的沉积时间为5min,薄膜厚度约1000nm,最低电阻率为0.75*10-4Ω·cm,薄膜在可见光范围(波长在400-700nm)内平均透光率为87.2%。衬底温度在200℃以上时呈现立方相结构。     

阴离子交换膜渗析法回收含硫酸钠的高浓度硫酸废水

根据Fick扩散定律 ,提出了测定H2 SO4和Na2 SO4在阴离子交换膜中扩散速度的方法 .静态法测定结果显示 ,对含 2 5 0～ 3 5 0g/LH2 SO4、1 0 0～ 1 2 0g/LNa2 SO4的废水 ,常温下 ,A2 0 和 3 3 62BW膜中H 平均扩散速度分别为 8.0× 1 0 -4m/h和 7.8× 1 0 -4m/h,Na 平均扩散速度分别为 5 .9× 1 0 -5m/h和 6.6× 1 0 -5m/h,这预示两膜都能实现废酸中H2 SO4和Na2 SO4的有效分离 .动态法分离废酸结果表明 ,H2 SO4回收率达 83 .4% ,回收酸中Na2 SO4含量下降至 5 .2 g/L     

用可溶性无机盐制备BaPbO3薄膜

以Ba（OH）2·8H2O和Pb（NO3）2为原料，以EDTA和柠檬酸为复合鳌合剂，采用溶胶-凝胶工艺制得BaPbO3薄膜研究了pH值、螯合剂用量对薄膜制备的影响以及薄膜的表面形态和成分发现薄膜的成分、致密度和错的价态都受热处理的影响膜厚0.1～0．4μm；薄膜的表面电阻率为150～500Ω／.     

Nb元素对Ba0.5Sr0.5NbzTi1-zO3薄膜结构与性能的影响

采用溶胶-凝胶法制备了Ba0.5Sr0.5NbzTi1-zO3薄膜（Nb=0-4．12mol％）,采用HPAgilent 429A阻抗分析仪等测试方法研究了微量元素铌对Ba0.5Sr0.5NbzTi1-zO3（BSNT）薄膜介电性能的影响。当Nb分别为0-4．12m01％时,相对介电常数占,降低而介质损耗tanδ均得到了改善,当测试频率为1kHz,tanδ由0．09降低到0．067;居里温度Tm逐渐移向低温;在测试频率2．0-10MHz范围内,εr、tanδ均能表现出较好的频散特性。采用XRD、TEM等测试方法分析了薄膜的结构特征。薄膜为四方钙钛矿晶体结构,但Nb的溶入改变了晶胞参数的c／a比,减小了薄膜的晶粒尺寸,提高了薄膜的致密度。     

超高真空(UHV)PECVD系统沉积a-Si1-XCX∶HK薄膜及其特性

本文研究了应用新型的超高真空等离子增强化学气相沉积 (VHV- PECVD)复合腔系统沉积a- Si1-XCX∶ HK薄膜及其特性。系统的真空度可达 10 -7Pa(10 -9Torr)以上。通过控制 H2 对常规用混合气体(Si H4 CH4 )的稀释程度以及相应的 CH4 比例 ,优化沉积工艺参数 ,制备出能带宽度范围变化较大的高质量非晶氢化硅碳 (a- Si1-XCX∶ HK)薄膜。通过 RBS、ERDA、IR和 Ramam光谱等方法分析和确定这种薄膜材料的基本特性。对 H2 氢稀释作用及其效应进行了分析。     

薄膜厚度对LiMn2O4薄膜性质的影响

采用溶液沉积法制备不同厚度的LiMn2O4薄膜，用x射线衍射及扫描电子显微镜检测和分析薄膜的物相及形貌；采用恒电流充放电及交流阻抗技术研究LiMn2O4薄膜的电化学性质。结果表明不同厚度的LiMn2O4薄膜均匀，晶粒大小相近，晶粒尺寸在20-50nm之间。当放电电流密度为100μA／cm^2时，不同厚度的LiMn2O4薄膜比容量相差不大，其值在42-47μAh／（cm^2．μm）之间。薄膜循环性能随着薄膜厚度的增加而变差，经50次循环后，薄膜每次循环的容量损失从0．18μm的0．012％升高到1．04μm的0．16％。电化学阻抗表明不同厚度的LiMn2O4薄膜的锂离子扩散系数差别不大，数量级为10^-11cm^2／s。     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Study on Bond Ability of Arc-Spraying Coatings with Different Surface Pretreatment on Cast-Iron

Arc spraying coatings are widely used in various applications, but uncommon in cast iron substrate. Different surface pretreatment technology is tested on substrates of gray cast iron. Surface roughness and residual stress were measured by TR200 and X-ray diffraction analyzer. Influence of different surface pretreatment methods ( dry blasting and fusebond) on roughness and residual stress was analyzed. The arc-sprayed coatings of wire 3Cr13 (φ2mm) on gray cast iron substrate is studied. The microstructure and interface of bonding layer were observed by SEM. The bond strength was taken by tensile test. Results show that bond strength with grit blasting is higher than fuse-bond; it is feasible to make wire 3Cr13 coating with arc spraying on cast iron substrate roughened by grit blasting.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Evaluation of fatigue life of steel using steel grain size

The insightful discussion of the relationship between the construction of metallographic and fatigue life and proposition of mathematical relationships describing this relationship was conducted in the paper. This paper presents a method for estimating the fatigue life, based on the construction of the microstructural material taking into account the grain size and the participation of ferrite and pearlite phase.