共查询到20条相似文献,搜索用时 125 毫秒
1.
对某生产车间的空调,选用电制冷机组和溴化锂吸收式制冷机组两种方案,主要从设备初投资费用、运行费用两方面进行比较,得出了采用蒸汽型溴化锂吸收式制冷机组不可行的结论。 相似文献
2.
3.
本文分析了原有用过热蒸汽供热状况,通过对冬季和夏季生产和生活用气的分析,以及过热蒸汽和饱和蒸汽对设备的腐蚀程度等进行对比,简述了蒸汽减压系统、蒸汽减温系统、厂区热力管网改造和凝结水综合利用设计思路及优化方案,并对集中供热系统进行了效益分析。 相似文献
4.
《制冷与空调(北京)》2019,(10)
为解决现有电子工厂生产车间空调系统采用的蒸汽加湿方式存在新风机预热量大、蒸汽加湿成本高及蒸汽冷凝积水等问题,提出一种汽化加湿方式,并对苏州某电子工厂空调系统改造前后能耗进行对比分析,结果表明,与传统蒸汽加湿方式相比,采用汽化加湿方式在相同送风条件下空调系统每小时运行费用可节约161.84元,对企业提高经济效益、推行节能减排具有积极意义。 相似文献
5.
本文介绍了蒸汽喷射式制冷的基本原理及组成。以一套船用330 k W蒸汽喷射式制冷系统为研究对象,分析了系统流程,并讨论了系统的热力学性质和系统控制。通过对该系统的分析和讨论,论证了大冷量蒸汽喷射式制冷机在船舶空调中应用的可行性。此外,本文还提出了一种蒸汽喷射式制冷与水-水换热制冷相结合的制冷模式。 相似文献
6.
温泉 《中国新技术新产品》2009,(7):48-49
本文主要介绍了某乳品公司生产用蒸汽所产生凝结水的回收系统的设计过程。重点从凝结水回收的重要性、回收方案的选取、现场施工及改造后的经济效益等五个方面来论述蒸汽凝结水回收在技术及经济上的可行性。 相似文献
7.
本文从生产实际出发,通过对生产过程使用低压蒸汽进行剖析,找出影响氧化铝生产低压蒸汽的因素,提出解决低压蒸汽综合利用的方案,并按照方案对生产流程进行改造。通过改造前后技术参数进行对比,为今后工业生产控制提供参考。 相似文献
8.
《制冷与空调(四川)》2020,(4)
为了利用"太阳能+"多能互补清洁供热项目夏季产生的热量,设计增加了一套可提供工业用低压蒸汽的系统和一套太阳能热辅助溴化锂吸收式制冷机组空调系统,可同时实现夏季制冷和生产蒸汽;监测了四个典型天气条件下太阳能热辅助溴化锂吸收式制冷机组空调系统的运行数据;提出了太阳能贡献率、节煤量、CO_2减排量的计算方法。 相似文献
9.
10.
介绍了天津石化蒸汽双效吸收式制冷站的设计概况。针对不同季节制冷负荷的差异,采用不同的制冷方式。冷冻水系统采用闭式循环,蒸汽系统设置了减温减压装置。对凝结水回收器进行了改进,使之同时满足凝结水回收和减温水供给的需要。试运行期间,出现了水泵电机过载的问题,分析为实际工作状态点偏离设计状态点所至,比较了3种不同处理方案,即采用增大局部阻力、变频和叶轮切削后增加局部阻力的方法加以修正。另外还出现蒸汽关断阀不能正常动作的情况,原因是阀门执行机构工作特性与制冷机工作原理不匹配,更换执行装置后动作正常。合理应用蒸汽双 相似文献
11.
Based on field data from a medium scale ammonia based milk refrigeration plant located in northern India, a trans-critical CO2 heat pump system with IHX is conceptualized for waste heat utilization. The waste heat is utilized to pre-heating the boiler feed water and thereby reduces energy consumption. A thermodynamic model of the refrigeration system is built and simulated for year-round field data. In this study, the condenser of the ammonia based refrigeration system is coupled with the evaporator of the proposed CO2 heat pump which is maintained at 20 °C year-round. The heat pump delivers heat at about 70 °C to pre-heat the boiler feed water drawn from underground source and is available in temperature range of 25 °C to 29 °C year-round. Thus, the CO2 heat pump performance is essentially independent of variation in ambient temperature. We reported reduction in CO2 emission and reduction in total energy cost by approximately 45.7% and 33.8% respectively. Economic analysis shows the payback period (PBP) is about 40 months. 相似文献
12.
Martin Pavlas Michal Touš Petr Klimek Ladislav Bébar 《Clean Technologies and Environmental Policy》2011,13(4):595-605
Discussion about utilization of waste for energy production (waste-to-energy, WTE) has moved on to next development phase.
Waste fired power plants are discussed and investigated. These facilities focus on electricity production whereas heat supply
is diminished and operations are not limited by insufficient heat demand. Present results of simulation prove that increase
of net electrical efficiency above 20% for units processing 100 kt/year (the most common ones) is problematic and tightly
bound with increased investments. Very low useful heat production in Rankine-cycle based cogeneration system with standard
steam parameters leads to ineffective utilization of energy. This is documented in this article with the help of newly developed
methodology based on primary energy savings evaluation. This approach is confronted with common method for energy recovery
efficiency evaluation required by EU legislation (Energy Efficiency—R1 Criteria). New term highly-efficient WTE is proposed and condition under which is the incinerator classified as highly efficient are specified and analyzed. Once
sole electricity production is compelled by limited local heat demand, application of non-conventional arrangements is highly
beneficial to secure effective energy utilization. In the paper a system where municipal solid waste incinerator is integrated
with combined gas–steam cycle is evaluated in the same manner. 相似文献
13.
14.
热力发电厂余热资源丰富,且存在锅炉烟气排入大气环境导致的"白羽"现象。为此,国内外学者对烟气余热利用展开了大量研究,其中吸收式热泵作为余热驱动的能级提升装置被广泛应用于区域集中供热和供冷领域。针对目前余热回收领域中应用的回热、多效、多级和压缩-吸收复合的吸收式热泵技术进行综述,并提出一种由双级吸收热泵、升温型压缩吸收耦合热泵和三级烟气换热器组成的烟气余热全热回收系统。该系统基于烟气余热能量梯级利用原理,将烟气由145℃降为40℃以下,同时制取70℃以上的一次热网供暖热水,有效地提升能源利用效率,减少"白羽"现象的产生。 相似文献
15.
16.
内燃机冷热电联供系统作为一种高效的能源利用方式,排烟余热回收后的排放温度在100℃左右,仍有部分低温余热没有充分利用,提出一种分布式冷热电三联供(distributed combined cooling heating and power,DCCHP)动力排烟低温余热耦合空气源热泵系统,实现了排烟余热的深度回收。以10 kW内燃机冷热电联供为基础,研究了该系统可回收余热量、热泵循环性能系数(coefficient of performance,COP)以及对一次能源利用率的影响。结果表明:在设计工况下,DCCHP系统排烟余热1.22 kW,热泵系统回收余热量可达1.07 kW,排烟余热回收率达到87.7%;热泵COP高达4.66,提高39.5%;系统一次能源利用率提高3.9%;同时解决了寒冷地区冬季热泵机组蒸发器结霜、低温环境下运行性能差的问题。此研究为冷热电联供系统与热泵机组的联合高效应用提供了重要的参考。 相似文献
17.
热电热泵热水器的研制与节能分析 总被引:3,自引:0,他引:3
热水器供水洗浴时,大部分热能随着废水的外排而浪费掉了,因而能源利用效率底下,而且热废水外排对环境造成了一定的热污染;尽管热电装置作为制冷系统效率较低,但作为热泵系统,相对于利用电能直接加热的装置其热输出效率却较高;热电热泵快热式热水器,通过回收洗浴废水热能达到了节能、环保的双重目的;卫生热水能耗在民用及各种商业建筑环境能耗结构中的比例日益增大,热电热泵装置为废热利用、建筑环境节能提供了新的思路. 相似文献
18.
分布式供能系统临近用户,具有灵活消纳可再生能源的优势。集成太阳能与清洁燃料互补的分布式供能系统,旨在实现太阳能与燃料的高效互补利用。提出了基于太阳能热化学的分布式供能系统,该系统集成了太阳能热化学转化与分布式冷热电联供系统,将太阳能与甲醇以热化学的形式进行源头互补,把太阳能转化为合成气燃料化学能,进而通过内燃机发电机组和余热回收单元输出冷、热、电产品,以满足用户的负荷需求。通过数值计算的方法,对所集成的系统开展了热力学性能及CO2排放性能分析,研究了设计工况及变工况下运行性能,结果表明所集成的太阳能与燃料热化学互补供能系统具有显著的节能减排优势。 相似文献
19.
Steven Kraines Hitoshi Shigeoka Hiroshi Komiyama 《Clean Technologies and Environmental Policy》2003,4(4):204-216
With the "Containers and Packaging Recycling Law", Japan has shown a firm conviction towards the promotion of recycling.
Waste can be "recycled", i.e. resource value of waste material can be recovered, in many ways, from material recycling to
energy recycling. Alternatively, waste can be reduced or disposed of in landfills. A system tradeoff model is developed from
component process technology models of six different recycling and disposal options for household plastic waste processing:
plastic pellet production, refuse derived fuel production, oil production, waste incineration to produce electricity, use
of waste plastic as a coke substitute, and incineration for volume reduction. These technologies are compared with the case
where all waste plastic is land filled. Models based on plant data, laboratory experiments, and theoretical considerations
of scale effects and mass balances are developed to calculate the cost, energy consumption, CO2 emission, and land fill occupancy. The models also calculate the valued products of each technology and convert them into
cost, energy, CO2, and landfill occupancy using life cycle inventory data. These values are subtracted from the outputs of the waste processing
models to obtain overall performances for each technology. The overall tradeoff system model is then used to evaluate several
scenarios of plastic recycling and disposal technologies in Tokyo.
Electronic Publication 相似文献
20.
目的 对比研究芒果果脯热泵干燥过程与传统化石能源热风干燥的成本效益,为企业生产提供科学指导。方法 在芒果果脯干燥动力学模型基础上,为芒果果脯的干燥生产过程建立生命周期成本与效益分析模型,辅以芒果热泵干燥实验数据,验证模型的正确性,并用该模型对芒果果脯热泵干燥企业的生产成本进行预测分析,比较采用热泵干燥和传统热风干燥方法的能耗、成本效益。结果 在热泵干燥条件下,不同高度层的芒果受热均匀,可以精准调控果干温度。相较于燃煤锅炉加热干燥,采用热泵干燥可以降低17.1%的生产成本,有利于减轻企业的经济负担。与传统锅炉加热干燥方法相比,采用热泵干燥方法可使生产能耗下降30.17%,二氧化碳排放量减少了32%,符合我国节能减排发展战略。结论 证明了热泵技术在芒果果脯干燥生产上的优越性。该模型方法还可用于龙眼、荔枝等同类农副产品生产中,为果脯果干生产企业的生产成本控制提供测算方法。 相似文献