Y1.34Gd0.60Eu0.06O3透明陶瓷材料的制备与发光性能

采用复合沉淀法制备了具有良好烧结活性的纳米级Y1．34Gd0．60Eu0．06O3粉体．经850℃／2h煅烧后，得到晶粒尺寸为30-40nm，且基本无团聚的Y1．34Gd0．60Eu0．06O3发光粉体，粉体比表面积为23m^2／g．该粉体经过适当的干压和等静压成型后，于1800℃以上温度烧结6h，可以获得Y1．34Gd0.60Eu0．06O3透明陶瓷．获得的透明陶瓷材料在波长250nm的紫外光激发下发射出较强的红光，发射主峰位于610nm，对应于掺杂Eu^3＋的^5D0-^7F2跃迁．     

(Y,Gd)2O3:Eu(YGO:Eu)纳米粉体合成及透明陶瓷制备

研究以碳酸氢铵作为沉淀剂制备Y1．34Gd0.6Eu0.06O3（YGO：Eu）纳米粉体的工艺，并采用真空烧结制备了YGO：Eu透明陶瓷．实验结果表明：以硝酸盐为母盐，以碳酸氢铵为沉淀剂，在本研究试验条件下获得的YGO先驱物为晶态的水合稀土碳酸钇钆正盐．先驱物在600℃煅烧后可以得到立方晶型的YGO粉体．煅烧温度对粉体的颗粒尺寸及尺寸分布有影响，1100℃煅烧所获得的粉体由粒径-100nm的球形颗粒组成，颗粒尺寸分布均匀，粉体具有较好的烧结性能．采用所制备的YGO：Eu纳米粉体，在1670℃真空烧结2h可获得透光性良好的透明陶瓷，样品在可见光区的最高透过率可达74．6％，高于相同工艺条件下制备的氧化钇透明陶瓷．     

湿化学法制备 Y2O3纳米粉及透明陶瓷

以Y(NO3)3溶液和NH3·H2O为原料,制备了Y2O3纳米粉体.先驱沉淀物的化学组成为Y2(OH)5NO3·H2O.研究了pH值及滴加过程对先驱沉淀物形貌及Y2O3产物烧结性的影响.正向滴定,pH值较低时(pH=7.9),先驱沉淀物为片状结构;pH值较高时(pH=10.0),先驱沉淀物片层状结构特性减轻,并且颗粒变的细小.反向滴加时,片层状结构特征消失,主要为块状晶粒.先驱沉淀物为片状结构时,得到的粉体活性较高.添加适量的(NH4)2SO4能够减轻Y2O3粉体的团聚,沉淀的同时控制pH值在9以下,所得到的粉体具有更好的烧结性能.采用得到的Y2O3纳米粉,不加入任何烧结助剂,经1700℃真空烧结4h得到了透明Y2O3陶瓷.     

不添加烧结助剂制备透明的Y2O3陶瓷

以Y2O3粗粉、碳酸氢铵、硝酸和氨水为原料,通过沉淀法制备了Y2O3纳米粉体.发现沉淀工艺和煅烧温度显著影响Y2O3纳米粉的颗粒大小和尺寸分布,从而影响烧结体的密度和透光性.用X射线衍射分析仪、透射电镜、图像分析仪等研究发现,pH=8时制得的沉淀先驱物经1000℃煅烧,可得到粒度为33 nm,近球形,分散性好,尺寸分布窄的Y2O3粉体.该粉体不加任何添加剂,在1700℃真空烧结4 h可得到透明Y2O3陶瓷.     

Al2O3-ZrO2(3Y)-SiC纳米复合材料的制备及性能

本文研究了非均相沉淀法制备Al2O3－ZrO2（3Y）－SiC复合粉体的工艺过程,认为粉体的理烧温度是至关重要的,热压烧结得到了致密的Al2O3－ZrO2（3Y）－SiC纳米复合材料,ZrO2的加入对烧结温度的影响不大．通过TEM观察,SiC颗粒均匀分散于材料中,大的ZrO2颗粒位于Al2O3晶粒间,小的圆形ZrO2颗粒位于Al2O3晶粒内,一部分Al2O3晶粒呈非等轴状．80Wt％Al2O3－15wt％ZrO2－5Wt％SiC纳米复合材料的抗弯强度可达555MPa,韧性为3.8MPa．m1／2.     

微波和真空烧结制备La2O3掺杂Al2O3透明陶瓷

通过共沉淀法制备La2O3掺杂Al_2O_3纳米粉,粉体经压制后分别采用微波和真空烧结制备Al_2O_3透明陶瓷。结果表明:Al_2O_3粉末颗粒大小均匀,近似球形,为40~60nm;两种烧结方式制备的试样XRD图中均为α-Al_2O_3,未检测到其它相。La2O3掺杂量为1%时,随烧结温度升高,两种烧结方法得到的Al_2O_3陶瓷的相对密度和抗弯强度均呈上升趋势,且微波烧结陶瓷的相对密度和抗弯强度明显高于真空烧结。1500℃烧结时,随La2O3掺杂量的增加,Al_2O_3陶瓷的相对密度均先增大后减小,当La2O3掺杂量为1%时,Al_2O_3陶瓷的相对密度和抗弯强度均最大。微波烧结陶瓷的透光率明显高于真空烧结,且其断口晶粒比真空烧结明显细少。     

机械合金化和放电等离子烧结制备Y3Al5O12陶瓷

采用机械合金化和放电等离子烧结制备YAG陶瓷,研究了球磨时间对原料颗粒大小和烧结合成YAG纯度的影响,并利用x射线衍射(XRD)、扫描电镜(SEM)等手段对反应过程及产物形貌和物相进行了分析.研究结果表明,机械合金化Y2O3和Al2O3粉体,可明显细化氧化物颗粒,球磨20h后,Y2O3和Al2O3晶粒大小约为34nm和32nm.球磨处理的Y2O3和Al2O3粉体具有很高的活性,促进放电等离子烧结低温反应合成和获得致密的YAG.对球磨20h的粉体在不同温度进行放电等离子烧结,在1200℃即可获得纯YAG陶瓷,在1500℃烧结,可得到相对密度为99.5%的YAG陶瓷.1500℃烧结的块体在可见光范围内透过率为13.8%.     

Y2O3和纳米AlN协同作用对氮化铝陶瓷烧结性能及热传导的影响

在微米氮化铝粉体中添加含量为4%的Y2O3和不同含量的纳米AlN粉体制备氮化铝陶瓷,研究了Y2O3和纳米AlN协同作用对微米氮化铝陶瓷烧结性能和热传导性能的影响。结果表明,Y2O3优先与纳米AlN粉体表面的Al2O3反应生成活性较高的第二相Al5Y3O12,相比于Y2O3与微米AlN粉体表面Al2O3反应生成的Al5Y3O12,具有更低的熔化温度及更好的流动性;同时,纳米AlN粉体的高比表面能也促进氮化铝陶瓷的致密化进程。二者的协同作用有效地促进氮化铝陶瓷的致密烧结,改善第二相的微观分布,从而能在较低的烧结温度下获得具有较高热导率的氮化铝陶瓷。当Y2O3和纳米AlN粉体的添加量(质量分数)分别为4%和1.5%时,在1800℃烧结得到的氮化铝陶瓷密度为3.26 g·cm-3,第二相以连续相的形式分布于氮化铝晶界处,热导率为151.75 W/(m.K)。     

共沉淀法制备Nd3+:Y2O3透明陶瓷

以Y2O3为基质材料,掺杂不同含量的Nd3+添加PEG和(NH4)2SO4为分散剂,采用共沉淀法制备出性能良好的Nd3+:Y2O3纳米粉.对前驱体和不同温度下煅烧后的粉体进行差热热重、X射线衍射、比表面积和透射电镜等分析.结果表明,前驱体产物为Y2(OH)5(NO3)·nH2O时,Nd3+完全固溶于Y2O3的立方晶格中,Nd3+:Y2O3粉体大小均匀,近似球形.随着煅烧温度的升高,颗粒逐渐长大,900℃煅烧2h后颗粒尺寸约为40～60nm;粉体在1700℃和真空度为1×10-3Pa条件下烧结6h得到的Nd3+:Y2O3透明陶瓷的透光率接近78%.     

溶胶-凝胶法制备纳米Y2O3粉体

为了改善Y2O3粉体的分散性,提高其烧结活性,试验以三乙醇胺和氨水为凝胶剂,利用溶胶-凝胶方法合成了纳米级Y2O3粉体,采用差热/热重、X射线衍射、透射电镜研究了前驱体的组成、前驱体在不同的煅烧温度下的物相变化以及煅烧粉体的分散性.结果表明,前驱体的组成为Y2(OH)5.14(NO3)0.86H2O,在500℃保温2h可直接生成立方相的Y2O3,煅烧至1000℃保温2h得到了结晶度高、分散性好、平均粒径为50nm、近球形的YO纳米粉体;三乙醇胺的加入有利于提高YO粉体的分散性.     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Study on Bond Ability of Arc-Spraying Coatings with Different Surface Pretreatment on Cast-Iron

Arc spraying coatings are widely used in various applications, but uncommon in cast iron substrate. Different surface pretreatment technology is tested on substrates of gray cast iron. Surface roughness and residual stress were measured by TR200 and X-ray diffraction analyzer. Influence of different surface pretreatment methods ( dry blasting and fusebond) on roughness and residual stress was analyzed. The arc-sprayed coatings of wire 3Cr13 (φ2mm) on gray cast iron substrate is studied. The microstructure and interface of bonding layer were observed by SEM. The bond strength was taken by tensile test. Results show that bond strength with grit blasting is higher than fuse-bond; it is feasible to make wire 3Cr13 coating with arc spraying on cast iron substrate roughened by grit blasting.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Evaluation of fatigue life of steel using steel grain size

The insightful discussion of the relationship between the construction of metallographic and fatigue life and proposition of mathematical relationships describing this relationship was conducted in the paper. This paper presents a method for estimating the fatigue life, based on the construction of the microstructural material taking into account the grain size and the participation of ferrite and pearlite phase.