3104铝合金高温塑性变形本构关系研究

在Gleebe-1500 热模拟机上,采用高温等温压缩试验研究了3104铝合金在高温压缩变形中的塑性变形本构关系.结果表明, 应变速率和变形温度的变化强烈影响合金流变应力的大小, 流变应力随变形温度升高而降低, 随应变速率提高而增大;可用含Zener-Hollomon 参数的本构方程σ＝(1/α)×ln{(Z/A)1/n [(Z/A)2/n 1]1/2}来描述3104铝合金高温压缩变形时的流变应力行为,解得A＝202854595.1s-1、n＝3.4046、α＝0.03886MPa-1.     

ZK60镁合金热压缩变形行为

为了研究ZK60镁合金的热变形行为,采用Gleebe-1500热模拟机在变形温度为423～673K、应变速率为0.001～10s-1条件下对合金进行的热压缩试验.分析合金流变应力与应变速率、变形温度之间的关系,通过引入Z参数建立合金流变应力本构方程,并观察合金变形过程中的显微组织演变.结果表明:变形温度低于473K且应变速率大于0.1s-1时试样发生宏观开裂;在变形温度较高和应变速率较低时,合金真应力-真应变曲线具有动态再结晶特征.随变形温度升高和应变速率的降低流变应力减小,热压缩后的组织中再结晶现象越明显;应变速率越高,再结晶晶粒越细小.     

Nitronic60奥氏体不锈钢热变形行为研究

在Gleeble-3800热模拟试验机上对Nitronic60奥氏体不锈钢进行高温等温压缩实验,研究该材料在变形温度为950—1 200℃、应变速率为0.01—10 s-1、真应变量0.9等条件下的热变形行为,并观察了变形后的显微组织。研究结果表明:在热压缩过程中,流变应力随变形温度的升高而降低,随应变速率的升高而增加;当变形速率较低时,材料在变形温度范围内均发生了动态再结晶。采用双曲正弦模型建立了相应的热变形本构关系,其热变形激活能为425.542 k J/mol,高温压缩变形时,Z参数和流变应力方程分别为Z=εexp(425.542/RT)=3.495×1015[sinh(0.005 93σ)]5.55,ε=3.495×1015[sinh(0.005 93σ)]5.55exp[-525.524/(RT)]。     

基于人工神经网络的Mg-Zn-Zr-Ce合金热压缩变形研究

为研究含稀土元素铈的镁合金中高温流变行为,利用热模拟试验机对Mg-6Zn-0.5Zr-1.5Ce合金在变形温度523～673 K、应变速率0.001～1 s-1范围内进行热压缩实验.基于真应力真应变实验数据构建了单隐层前馈误差反向传播人工神经网络模型,利用该模型对ZK60-1.5Ce合金的流变应力行为进行预测,并分析了变形温度、应变速率与真应变对流变应力的影响.研究表明:Ce添加可显著细化晶粒;该镁合金的流变应力随变形温度降低和应变速率升高而增加;其流变应力行为可用双曲正弦函数进行描述,依据峰值应力拟合求得该合金的表观激活能为161.13 kJ/mol;变形温度和应变速率对流变应力的影响高于真应变.所建立的人工神经网络模型可以很好地描述该镁合金的流变应力,其预测值与实验数值吻合良好.     

高纯钛热变形的本构模型及微观组织演变

利用轴对称单向压缩法研究了纯钛在变形温度从723~873 K范围内、应变速率从0.001~1 s-1下的热压缩行为,并通过背散射电子衍射技术对不同热变形条件下的微观组织进行表征。研究结果表明,高温轴对称单向压缩下的纯钛经历从应变硬化阶段到稳态变形阶段的过程,在低的应变速率条件下材料流变应力出现平台,高的应变速率条件下,流变应力随变形过程逐渐增加。该合金流变应力的大小受变形温度、应变速率的强烈影响,随变形温度升高而降低,随应变速率提高而增大,高纯钛是一种具有正应变速率敏感性的材料。该合金高温流变应力σ可采用ZenerHollomon参数的函数来描述,函数表达式中参数A、α和n的值分别为1.84×1024s-1、0.013 MPa-1、12.66,其热变形激活能Q为415.69 k J/mol。不同Z参数条件下微观组织对比分析表明在高的Z参数条件下,材料未发生动态再结晶,在低的Z参数条件下,材料发生明显的动态再结晶,在Z值介于两者之间时材料发生部分再结晶。     

Cu-Ni-Si-P合金动态再结晶研究及组织转变

在Gleeble-1500D热模拟试验机上,对Cu-2.0Ni-0.5Si-0.03P合金进行高温压缩实验,应变速率为0.01～5s-1、变形温度为600～800℃,对其高温等温压缩流变应力行为进行了研究.研究结果表明:随变形温度升高,合金的流变应力下降,随应变速率提高,流变应力增大.在应变温度为750、800℃时,合金热压缩变形流变应力出现了明显的峰值应力,表现为连续动态再结晶特征.可采用Zener-Hollomon参数的双曲正弦函数来描述Cu-2.0Ni-0.5Si-0.03P合金高温变形时的流变应力行为.从流变应力、应变速率和温度的相关性,得出了该合金高温热压缩变形时的应力指数n,应力参数α,结构因子A,热变形激活能Q和流变应力方程.合金动态再结晶的显微组织强烈受到变形温度的影响.     

Ti−6Mo−5V−3Al−2Fe−2Zr合金热变形行为及热加工图

目的 建立近β钛合金Ti−6Mo−5V−3Al−2Fe−2Zr(质量分数)的热变形本构方程,绘制热加工图,确定该合金的流变失稳区和适宜加工区,为其在工业生产中热加工工艺参数的制定提供指导。方法 在变形温度700~ 850 ℃、应变速率0.000 5~0.5 s⁻¹、真应变0.7的条件下,对近β钛合金Ti−6Mo−5V−3Al−2Fe−2Zr进行热压缩实验;基于Arrhenius方程建立该合金的热变形本构方程,并对方程进行验证;根据Prasad失稳准则,构建该合金的热加工图。结果 该合金的流变应力随着变形温度的升高而减小,随着应变速率的增大而增大;其热变形激活能为226.29 kJ/mol,本构方程为;通过热变形本构方程得到的峰值应力计算值与实验值平均误差为4.21%。结论 建立的热变形本构方程预测了流变应力,描述了该合金的热变形行为;通过叠加合金的能量耗散图和流变失稳图,获得了该合金的热加工图。基于热加工图确定该合金的流变失稳区为变形温度700~755 ℃与784~850 ℃、应变速率0.5~0.05 s⁻¹,最佳加工区为变形温度836~850 ℃、应变速率0.000 5~0.005 s⁻¹。     

Cu-2.32Ni-0.57Si-0.05P合金热压缩变形研究

在Gleeble-1500D热模拟试验机上,对Cu-2.32Ni-0.57Si-0.05P合金在应变速率为0.01～5s-1、变形温度为600～800℃、最大变形程度为60%条件下,进行恒温压缩模拟实验研究.分析了实验合金在高温变形时的流变应力、应变速率及变形温度之间的关系,研究了变形温度对合金显微组织的影响.计算了合金高温热压缩变形时的应力指数n、应力参数α、结构因子A以及平均热变形激活能Q.结果表明:合金的流变应力随变形温度升高而降低,随应变速率提高而增大.热变形过程的流变应力可用双曲正弦本构关系来描述.当变形温度高于750℃时,合金流变曲线呈现出明显的动态再结晶特征,合金显微组织为完全的动态再结晶组织.合金的热加工宜在应变速率为0.1～1s-1、温度为700～800℃范围内进行.     

Al-3%Cu-2%Li合金的热变形行为

在Gleeble-1500热模拟仪上进行热压缩实验,研究了变形温度为350~500℃,应变速率为0.001,0.01,0.1和1s-1时Al-3%Cu-2%Li合金的热变形行为。利用双曲正弦本构关系分析热变形中的流变应力,采用金相分析热变形中合金的显微组织变化。结果表明,该合金流变应力的大小受变形温度、应变速率的强烈影响,它随变形温度升高而降低,随应变速率提高而增大,该合金高温流变应力可采用Zener-Hollomon参数的函数来描述,其热变形激活能为325.48kJ/mol。     

Cu-Cr-Zr-Ce合金高温热变形行为研究

Cu-Cr-Zr系合金是一类高强度高导电集成电路用引线框架铜合金。在Gleeble-1500D热模拟实验机上,采用等温压缩实验研究了Cu-Cr-Zr-Ce合金在变形温度为600～800℃、应变速率为0.01～5s-1条件下的流变应力的相互变化规律,测定了其真应力-应变曲线,并利用光学显微镜分析了合金在热压缩过程中的组织演变规律。结果表明,Cu-Cr-Zr-Ce合金的真应力-真应变曲线呈现典型的动态回复特征,其流变应力和峰值应力随变形温度的降低和应变速率的提高而增大;且变形温度越高,应变速率越小,合金越容易发生动态回复和再结晶。在上述实验基础上,基于流变应力、应变速率和温度的相关性,计算出了该合金热压缩变形时的热变形激活能Q,并建立了其等温压缩塑性变形过程的流变应力与变形温度和应变速率之间关系的本构方程。     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.