PP-g-MAH/蒙脱土纳米复合材料的制备和性能

采用熔融插层法成功制备了接枝物(PP—g—MAH)／有机蒙脱土(Org—MMT)纳米复合材料，用X射线衍射法检测了复合材料的层间距、微晶尺寸和晶胞参数的变化，并考察了纳米复合材料的力学性能。结果发现，对于PP—g—MAH／Org—MMT=100：20的复合材料，接枝物大分子链难以插层进入有机蒙脱土片层间。增大PP—g—MAH／Org—MMT比例，接枝物大分子链能插层进入有机蒙脱土片层，形成插层型纳米复合材料。PP—g—MAH／Org—MMT=100：10时，PP—g—MAH／Org—MMT复合材料110、040、041等晶面垂直于反射方向的微晶尺寸出现最小值．且可获得较好的力学性能．说明选择适当的接枝物／有机蒙脱土比例可降低聚丙烯的微晶尺寸，改善力学性能．但对复合材料晶胞参数的影响较小。     

阳离子表面活性剂为乳化剂原位乳液聚合制备PS/MMT纳米复合材料

针对原位乳液聚合法制备聚合物/蒙脱土(MM T)纳米复合材料,为了实现蒙脱土片层的有机化处理和纳米复合材料的形成一步完成,以十六烷基三甲基溴化铵为乳化剂原位乳液聚合制备了PS/MM T纳米复合材料。XRD、FT-IR、TEM等分析表明,聚苯乙烯已插层进入蒙脱土的层间。在制备过程中,CTAB既充当了乳化剂,又充当了蒙脱土的插层处理剂,促进了苯乙烯在蒙脱土层间的聚合,同时也造成了蒙脱土片层一定程度的聚并。DSC分析表明,复合物的玻璃化转变温度有一定程度的提高。另外,还对蒙脱土存在下乳液聚合的特点进行了研究,发现MM T片层对乳液聚合的影响仅在聚合反应的初始阶段,使聚合速率有所下降,而对反应的后期阶段和反应产物的分子量影响不大。     

有机蒙脱土的复合插层及分散性研究

以钠基蒙脱土(MMT)为原料,十六烷基三甲基溴化铵(CTAB)和己内酰胺为插层剂制备了复合插层有机蒙脱土(OMMT).红外光谱分析(IR)、热重分析(TGA)和X射线衍射分析(XRD)表明,有机插层剂已进入蒙脱土的层间,CTAB/己内酰胺复合插层有机蒙脱土的层间距大于单阳离子CTAB插层有机蒙脱土的层间距.Molau实验结果表明,这种有机蒙脱土在有机介质中表现出很好的分散性.     

LLDPE/HDPE/MMT纳米复合材料的制备及性能研究

以线性低密度聚乙烯(LLDPE)、高密度聚乙烯(HDPE)、有机改性的蒙脱土(MMT)为主要原料,选用乙烯-醋酸乙烯酯接枝马来酸酐(EVA-g-MAH)作为增容剂,采用熔融插层法制备了线性低密度聚乙烯/高密度聚乙烯/蒙脱土(LLDPE/HDPE/MMT)纳米复合材料。通过X射线衍射(XRD)分析蒙脱土在聚乙烯基体中的分散情况,并研究蒙脱土的含量对其在基体中分散效果的影响。TG实验结果表明,蒙脱土的加入使LLDPE/HDPE/MMT纳米复合材料的热稳定性得到很大的提高。由DSC曲线可以得出,加入蒙脱土的复合材料相比于纯聚合物,其熔点和热分解温度都有很大的提高,提高程度与蒙脱土的含量有关。     

聚丙烯/蒙脱土纳米复合材料的结构与性能

采用复合季胺盐制备反应性有机蒙脱土并参与三单体固相接枝聚合，加强蒙脱土（MMT）的熔融插层和稳定MMT的插层结构，制备剥离型的聚丙烯／蒙脱土纳米复合材料（PPMN）．通过X射线衍射（XRD）、傅立叶变换红外光谱（FTIR），透射电镜（TEM）等测试手段研究了PPMN的结构和性能．结果表明：复合有机化和固相接枝的确加强了MMT的熔融插层．MMT的复合有机化和固相接枝的放热过程有助于MMT层间涨大和MMT剥离结构的形成．当PPGM的添加量在6—8phr时，PPMN的力学性能、流动性能和热性能达到一个较好的增强状态．PPMN力学性能和热性能的提高归功于剥离的蒙脱土的增强作用和接枝低聚物原位形成的界面增容作用；PPMN流动性能的改善来源于剥离的蒙脱土和固相接枝形成的低聚物的增塑作用．     

聚丙烯/蒙脱土纳米复合包装材料的制备与力学性能研究

采用熔融插层法在双螺杆挤出机中制备了聚丙烯(PP)/蒙脱土(MMT)纳米复合材料,纳米复合材料机械性能测试结果表明,当有机蒙脱土(MMT)质量比为2%时,复合材料的综合力学性能明显优于聚丙烯(PP).扫描电镜观测不到纳米复合材料中明显的有机-无机相畴,表明蒙脱土(MMT)片层分散均匀,分散尺度已基本达到纳米级.     

固相法改性蒙脱土在聚氯乙烯中的应用

采用插层剂季磷盐和KH-560硅烷偶联剂对钠基蒙脱土进行固相法改性得到有机蒙脱土,并通过熔融插层法制备了聚氯乙烯(PVC)/有机蒙脱土(OMMT)纳米复合材料,通过哈克流变仪、X射线衍射(XRD)和透射电镜(TEM)测试对比了钠基蒙脱土(MMT)和OMMT增强PVC复合材料的结构和性能。研究发现,蒙脱土、季磷盐与KH-560质量份为100∶10∶4时改性效果最佳,OMMT最佳用量为3份,PVC/OMMT3的流变性能明显优于PVC/MMT3,且PVC/OMMT材料中有机蒙脱土的层间距较大、层片分散更均匀。     

有机蒙脱土的制备及应用研究

采用正交实验法以十六烷基三甲基溴化铵(CTMAB)为插层剂,制备了有机蒙脱土,优化条件为:固液比5％,反应温度90℃,反应时间2h.红外光谱表明CTMAB插层到蒙脱土片层中,XRD显示晶层间距增大,TG-DSC-DTA表明在335.5℃有明显放热峰,TEM表征片层结构被解离.将有机蒙脱土添加到环氧树脂中,较大地提高了环...     

原位聚合制备聚乙烯/蒙脱土纳米复合材料

首先用乳液聚合法得到聚苯乙烯丙烯腈共聚物改性的蒙脱土，然后利用蒙脱土片层上的羟基和聚合物链上的极性官能团负载茂金属催化剂并通过原住聚合法制得聚乙烯／蒙脱土(PE／MMT)蚋米复合材料。XRD和TEM电镜分析结果表明蒙脱土在聚乙烯基体中呈蚋米级分散。DSC分析结果表明，复合材料的熔点比纯PE高2℃～5℃，DMA分析结果表明，复合材料的储能模量较纯聚乙烯有较大辐度的增长。     

溶液聚合制聚丙烯酰胺/蒙脱土纳米复合材料

利用溶液聚合法制备了聚丙烯酰胺／蒙脱土插层复合材料。XRD、IR等表明，聚丙烯酰胺已进入蒙脱土层间，并使之剥离。DSC表明，剥离型纳米复合材料的热稳定性提高，这是由于蒙脱土纳米片层与基体大分子链相互作用的结果。研究结果表明，复合材料调湿性能优于基体材料。     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Study on Bond Ability of Arc-Spraying Coatings with Different Surface Pretreatment on Cast-Iron

Arc spraying coatings are widely used in various applications, but uncommon in cast iron substrate. Different surface pretreatment technology is tested on substrates of gray cast iron. Surface roughness and residual stress were measured by TR200 and X-ray diffraction analyzer. Influence of different surface pretreatment methods ( dry blasting and fusebond) on roughness and residual stress was analyzed. The arc-sprayed coatings of wire 3Cr13 (φ2mm) on gray cast iron substrate is studied. The microstructure and interface of bonding layer were observed by SEM. The bond strength was taken by tensile test. Results show that bond strength with grit blasting is higher than fuse-bond; it is feasible to make wire 3Cr13 coating with arc spraying on cast iron substrate roughened by grit blasting.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Evaluation of fatigue life of steel using steel grain size

The insightful discussion of the relationship between the construction of metallographic and fatigue life and proposition of mathematical relationships describing this relationship was conducted in the paper. This paper presents a method for estimating the fatigue life, based on the construction of the microstructural material taking into account the grain size and the participation of ferrite and pearlite phase.