用溶胶－凝胶法在碳纤维表面涂覆Al_2O_3

本文研究用溶胶－凝胶方法在碳纤维表面涂覆Ａｌ＿２Ｏ＿３，的工艺对涂层性能、结构及对纤维强度、抗氧化性能等的影响。结果表明：所配溶胶质量好，涂覆工艺合适，可在纤维表面得到均匀、连续的Ａｌ＿２Ｏ＿３，涂层；该涂层不仅改善了纤维的抗氧化性能，而且还能保持纤维原有的强度；改善与熔铝的润湿性，为复合材料的制备提供方便。     

TiO2—Al—B系反应烧结制备的复相陶瓷和原位Al基复合材料

采用反应烧结方法，利用ＴｉＯ２，Ａｌ和Ｂ粉末间的放热反应的较低的温度下制备Ａｌ２Ｏ３－ＴｉＢ２复相陶瓷和原位生长Ａｌ２Ｏ３和ＴｉＢ２弥散粒子增强Ａｌ复合，Ａｌ２Ｏ３－ＴｉＢ２复相陶瓷是密度ρ－０．８的多孔体，由尺寸小于２μｍ，在基体中呈现均匀分布，没有发现Ａｌ３Ｔｉ生成，这种原位Ａｌ基复合材料具有优于ＳｉＣｗ／Ａｌ复合材料的强度。     

添加Al2O3对SiC板粒／Y—TZP复合材料力学性能的影响

本以ＳｉＣ板粒、ＺｒＯＣｌ２·８Ｈ２Ｏ、ＡｌＣｌ３和Ｙ（ＭＯ）３为原料，利用共沉淀和热压烧结工艺，制备ＳｉＣ板粒／Ｙ－ＴＺＰ和（含Ａｌ２Ｏ３）ＳｉＣ板粒／Ｙ－ＴＺＰ复合材料。测试了材料的室温和高温力学性能。研究了添加Ａｌ２Ｏ３对ＳｉＣ板粒／Ｙ－ＴＺＯ复合材料的影响。结果表明，ＳｉＣ板粒／Ｙ－ＴＺＰ复合材料与Ｙ－ＴＺＰ复合材料与Ｙ－ＴＺＰ陶瓷相比，其室温强度和韧性出现明显下降，高温强度也没有改善；     

TiO_2－Al－B系反应烧结制备的复相陶瓷和原位Al基复合材料

采用反应烧结方法，利用ＴｉＯ２，Ａｌ和Ｂ粉末间的放热反应在较低的温度下制备Ａｌ２Ｏ３－ＴｉＢ２复相陶瓷和原位生长Ａｌ２Ｏ３和ＴｉＢ２弥散粒子增强Ａｌ复合材料Ａｌ２Ｏ３－ＴｉＢ２复相陶瓷是密度ρ～０．８的多孔体，由尺寸约１０μｍ的生长单元构成晶粒，在陶瓷中还含有少量的Ａｌ３Ｔｉ．Ａｌ基复合材料中原位形成的Ａｌ２Ｏ３和ＴｉＢ２粒子尺寸小于２μｍ，在基体中呈现均匀分布，没有发现Ａｌ３Ｔｉ生成．这种原位Ａｌ基复合材料具有优于ＳｉＣｗ／Ａｌ复合材料的强度．     

TiO2／Al烧结反应生成的Al2O3／TixAly复合材料研究

采用挤压铸造法，先制备ＴｉＯ２／Ａｌ坯块，经随后高温烧结反应，可生成Ａｌ２Ｏ３／ＴｉｘＡｌｙ复合材料。ＤＴＡ分析表明ＴｉＯ２粉末与纯Ａｌ之间的反应具有放热特征。Ｘ射线衍射分析与透射电镜观察发现反应产物主要为α－Ａｌ２Ｏ３与ＴｉｘＡｌｙ。反应过程中ＴｉＯ２粉末首先被熔融态Ａｌ还原成α－Ａｌ２Ｏ３与Ｔｉ，而后Ｔｉ与Ａｌ通过扩散反应形成多种ＴｉｘＡｌｙ金属间化合物。     

共沉淀法制备Al_2O_3-YAG复相陶瓷及其显微结构研究

用共沉淀法制备了Ａｌ２Ｏ３－ＹＡＧ复合粉体,ＹＡＧ的结晶温度在１０００℃左右．共沉淀法 制备的Ａｌ２Ｏ３－ＹＡＧ复合粉体经１５５０℃热压烧结,获得致密烧结体,ＹＡＧ的加入量对烧结温度 的影响不大． Ａｌ２Ｏ３－５ｖｏｌ％ＹＡＧ复合材料的抗弯强度为６０４ＭＰａ,断裂韧性为５．０ＭＰａｍ１／２; Ａｌ２Ｏ３－２５ｖｏｌ％ＹＡＧ复合材料的抗弯强度为６１１ＭＰａ,断裂韧性为４５ＭＰａｍ１／２．所有这些数据 都高于单相Ａｌ２Ｏ３陶瓷的力学性能,说明ＹＡＧ的加入有利于Ａ１２Ｏ３陶瓷力学性能的提高． 通过显微结构观察发现：大的ＹＡＧ颗粒位于Ａｌ２Ｏ３晶界上,小的ＹＡＧ颗粒位于Ａｌ２Ｏ３晶粒 内．在 Ａｌ２Ｏ３－５ｖｏｌ％ＹＡＧ复合材料中,许多小的白色区域存在于 Ａｌ２Ｏ３晶粒内,这可能和较低 的Ｙ２Ｏ３含量有关．     

金属间化合物／Al2O3陶瓷复合材料研究新进展

本文主要介绍了Ｎｉ－Ａｌ／Ａｌ２Ｏ３、Ｔｉ－Ａｌ／Ａｌ２Ｏ３和Ｆｅ－Ａｌ／Ａｌ２Ｏ３三种复合材料的最新研究进展情况,对它们的最新研究动态进行了综述。着重介绍了Ｆｅ－Ａｌ／Ａｌ２Ｏ３的研究进展,并认为Ｆｅ－Ａｌ／Ａｌ２Ｏ３是一种应用前景非常广阔的新型材料,添加合金元素是进一步提高其性能的重要途径。     

添加Al_2O_3对SiC板粒／Y－TZP复合材料力学性能的影响

本文以ＳｉＣ板粒、ＺｒＯＣｌ２－８Ｈ２Ｏ、ＡｌＣｌ３和Ｙ（ＭＯ）３为原料，利用共沉淀和热压烧结工艺，制备ＳｉＣ板粒／Ｙ－ＴＺＰ和（含Ａｌ２Ｏ３）ＳｉＣ板粒／Ｙ－ＴＺＰ复合材料．测试了材料的室温和高温力学性能．研究了添加Ａｌ２Ｏ３对ＳｉＣ板粒／Ｙ－ＴＺＯ复合材料的影响．结果表明，ＳｉＣ板粒／Ｙ－ＴＺＰ复合材料与Ｙ－ＴＺＰ陶瓷相比，其室温强度和韧性出现明显下降，高温强度也没有改善；而在ＳｉＣ板粒与Ｙ－ＴＺＰ复合的基础上，添加Ａｌ２Ｏ３可明显提高材料的强度和断裂韧性，同时，材料的高温强度也获得显著改善．     

Al2O3—TiC—Co新型复合材料的力学性能及断裂行为

对于钴包覆陶瓷粉末热压烧结的Ａｌ２Ｏ３－ＴｉＣ－Ｃｏ新型复合材料力学性能和断裂行为进行了研究。结果表明，Ｃｏ在基体中以金属相存在，分布于晶界的金属钴的存在能有效地改善Ａｌ２Ｏ３－ＴｉＣ材料的力学性能，影响其断裂行为。     

Al—Al2O3—玻璃复合材料的制备与性能

采用无压烧结工艺，制备了Ａｌ－Ａｌ２Ｏ３－玻璃复合材料。研究了Ａｌ－玻璃，Ａｌ２Ｏ３－玻璃的润湿性。发现玻璃能促进Ａｌ与Ａｌ２Ｏ３结合；Ａｌ－Ａｌ２ｏ３－玻璃复合材料具有良好的强度和耐磨损性能。     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Study on Bond Ability of Arc-Spraying Coatings with Different Surface Pretreatment on Cast-Iron

Arc spraying coatings are widely used in various applications, but uncommon in cast iron substrate. Different surface pretreatment technology is tested on substrates of gray cast iron. Surface roughness and residual stress were measured by TR200 and X-ray diffraction analyzer. Influence of different surface pretreatment methods ( dry blasting and fusebond) on roughness and residual stress was analyzed. The arc-sprayed coatings of wire 3Cr13 (φ2mm) on gray cast iron substrate is studied. The microstructure and interface of bonding layer were observed by SEM. The bond strength was taken by tensile test. Results show that bond strength with grit blasting is higher than fuse-bond; it is feasible to make wire 3Cr13 coating with arc spraying on cast iron substrate roughened by grit blasting.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Evaluation of fatigue life of steel using steel grain size

The insightful discussion of the relationship between the construction of metallographic and fatigue life and proposition of mathematical relationships describing this relationship was conducted in the paper. This paper presents a method for estimating the fatigue life, based on the construction of the microstructural material taking into account the grain size and the participation of ferrite and pearlite phase.