岩石声发射信号能量分布特征的EMD分析

冲击荷载作用下岩石声发射信号具有瞬态性和多样性的特点,属于典型的非平稳信号。利用EMD方法对岩石声发射信号进行分解,得到一系列具有不同特征时间尺度的IMF分量,对每一个平稳的IMF分量提取能量特征。分析结果表明：冲击荷载作用下岩石声发射信号能量主要分布在前4个IMF分量内,且分布不均匀;岩石声发射信号各IMF分量的频谱与原始信号的频谱基本一致;随着岩石的密度、纵波波速、弹性模量的降低,冲击荷载作用下岩石声发射信号的优势频率越来越集中,且其优势频率有往低频发展的趋势;相比小波包分析,EMD分析法对于非平稳信号而言更具适应性。     

受载混凝土破坏全过程声发射信号频带能量特征

为寻找更有效的混凝土工程破坏前兆判据,开展混凝土单轴加载破坏全过程声发射试验。通过SAEU2S型数字声发射采集系统直接采集破坏全过程声发射信号波形,分别用FFT变换及小波包变换对不同破坏阶段声发射信号分析处理,发现不同破坏阶段声发射信号频率分布、频带能量变化规律,并从声发射信号频率变迁与裂纹扩展关系角度阐释混凝土破坏机理。采用小波包变换频带能量计算方法在Matlab中计算并绘制不同破坏阶段声发射信号频带能量分布直方图,重点分析0~26 kHz低频带能量占比及随加载时间变化规律,提出低频能量占比达某门限值即为破坏临界点的重要判据指标。此规律可作为混凝土工程稳定性监测预警前兆判据,对评估混凝土内部损伤具有理论指导意义。     

碎片云撞击声发射信号能量特征小波包分析

利用小波包分析技术对碎片云撞击载荷作用下铝合金板声发射信号的能量分布特征进行了研究。首先,介绍了碎片云撞击信号的获取方案及撞击引起的损伤情况;其次,对获取的声发射信号进行小波包分析,得到了信号在频率带上能量分布特征图。最后,讨论了碎片云撞击损伤特征与声发射信号能量分布的关系。分析结果发现,对于相同质量的弹丸,随着其破碎程度的提高,形成的碎片云对后板的损伤程度减少;弹丸具有的初始速度越大,弹丸破碎越完全,碎片云撞击声发射信号中的能量越小;当弹丸破碎程度低时,碎片云撞击引起的声发射信号能量集中在约488kHz以下;弹丸破碎程度越高,信号中488kHz以上的能量所占总能量的比例越大。     

基于小波包分析的拉索损伤声发射信号特征提取

结合显式有限元和小波包分析技术开展了拉索损伤声发射信号特征提取的仿真分析。采用ANSYS/LS-DYNA模拟得到拉索损伤声发射信号的仿真信号,基于小波包能量谱对拉索声发射的有限元仿真信号进行了特征提取,从小波包分解层次、特征频带数量的选择及特征参数的噪声鲁棒性三个方面开展了讨论分析。结果表明:(1)通过选择适当的小波包分解层次,小波包能量谱可以精细地反映信号的特征;(2)选取少数特征频带就能使得小波包能量谱反映声发射信号的特征信息;(3)基于小波包能量谱的特征参数具有良好的损伤敏感性及噪声鲁棒性,能在强噪声影响下实现对拉索不同损伤类型的判别。     

爆破条件对爆破震动信号分析中小波包时频特征的影响

非平稳信号的小波包分析是在小波变换基础上发展起来的 ,它对小波分析中没有细分的高频部分进一步分解 ,从而能够对信号局部信息进行更为精细的掌握。爆破条件是影响爆破震动时频特征分布的主要因素之一。本研究中 ,针对在不同段药量、不同微差间隔时间及近似相同的其它条件下产生的爆破震动信号 ,运用小波包分析方法对其进行了时频分析 ,主要探讨了段药量、段微差间隔时间对爆破震动时频分布的影响规律。段药量对爆破震动波形时频特征的影响主要体现在各层小波包主振频带内的细节信号峰值质点振速方面 ,各细节信号的峰值质点振速随段药量增加而增大 ,但主振频带分布保持基本的一致性 ,同一主振频带下小波包细节信号的阻尼比也趋于一致 ;段微差时间间隔对爆破震动时频特征的影响主要表现在 :延长各主振频带小波包细节信号的振动持时 ,不同微差单段波形的叠加增加了主振频带个数 (优势频率个数 )并使各频带内的优势频率值有微弱增大的趋势     

刀具磨损声发射信号小波分析中小波基的选取

针对在用小波理论分析刀具磨损声发射（AE）信号时选取不同的小波基对分析结果有重要影响的问题,通过对小波基性质和刀具磨损AE信号特点的研究,从理论上分析了小波分析中刀具磨损AE信号处理中小波基选取的方法。在试验验证过程中,根据信号在小波包分解前后遵循能量守恒的原理,用四种小波基对刀具磨损AE信号进行三层小波包分解。以经小波包分解后AE信号各频带上的频带能量为特征参数,比较四种情况下特征参数的变化,验证了理论分析的正确性。     

应力波作用下岩石声发射实验研究

在霍普金森（SHPB）冲击系统上进行了应力波作用下岩石声发射实验,获得了该加载条件下岩石破裂的声发射规律。实验结果表明,应力波下,声发射峰值能量之前所出现的声发射信号相当匮乏;而且其能量规律呈现出两种明显不同的特征：I型,声发射峰值能量之后,能量迅速衰减,到了加载的末期,能量出现了一定的回升,产生了“拐点”;II型,声发射峰值能量之后,能量衰减相对I型较慢,且不出现“拐点”。研究结果表明,声发射的能量特征与岩石破碎的程度密切相关;冲击载荷作用下岩石的声发射不仅仅是裂纹信息的反映,其中也包含了对应力波信号的反映。     

基于声发射的真空泄漏在线检测技术研究

真空泄漏是气体动力系统运行过程中的常见故障,传统的氦质谱检漏无法实现对真空泄漏的在线检测。本文利用声发射技术阐述了基于声发射信号的真空泄漏在线检测原理,通过真空泄漏声发射检测模拟试验,并利用参数特征分析法和平均频谱分析法对不同泄漏孔径下产生的声发射信号的特征进行了研究,得到了相应的小波包归一化频带能量分布特征。研究结果表明,真空泵运行的平均时域信号频带在20kHz以下,气体泄漏激发出大量的高频声发射信号,泄漏信号参数特征值与泄漏孔径的大小密切相关,泄漏信号的归一化能量分布一致性较好。声发射技术对于真空泄漏的在线检测及泄漏量评价等有实际意义。     

基于小波包能量谱的声发射信号处理技术

为实现材料早期结构疲劳损伤程度的监测与评价,提出采用小波包能量谱的声发射信号处理方法.首先,搭建金属疲劳损伤在线声发射监测系统,采集金属材料早期结构疲劳损伤产生的裂纹扩展与闭合的声发射信号;其次,选取适用于该声发射信号的小波函数和小波包分解层数,从而得到小波包分解后的各个频带的能量随疲劳周期数增加的变化情况的小波包能量谱图.实验表明:上述信号处理方法可获得能表征金属材料随着疲劳周期数增加的早期结构疲劳损伤程度变化的频带特征,为桥梁结构、建筑工程结构构件中常用钢材疲劳过程的声发射监测及早期疲劳损伤程度的加剧提供参考依据.     

缓冲孔对爆破振动信号幅频特性影响研究

为探索缓冲孔对爆破振动信号的峰值质点振动速度、主振频率和各频带能量分布等的影响,依托贵州某露天矿临近边坡爆破振动试验,获得了现场主爆破和缓冲爆破的振动信号。分别采用小波包分析和数值模拟方法对采用主爆破和缓冲爆破的振动信号进行分析。结果表明,临近边坡缓冲爆破具有明显的减震效应。相同测点条件下,水平切向振动信号的减振率最大,减振效果最好。且随着测点距爆源的距离越近,其减振效果越好。爆破振动信号的能量主要集中于60 Hz以内且分布极不均匀,存在多个主振频带。设置缓冲孔进行临近边坡爆破时,其振动信号的能量更向高频的主振频带集中,有利于避开边坡的自振频率。     

Estimation of Parameters of Universal Distribution of Moments of Failure of Products

A method is proposed for estimating the parameters of a mixture of exponential and Weibull distributions for which the accuracy of preliminary estimates obtained by graphical analysis is refined in accordance with the criterion of maximum likelihood. The efficiency of the proposed method is supported by the results of statistical modeling.     

Evaluation of optical properties of highly scattering media by moments of distributions of times of flight of photons

A novel method for the determination of the optical properties of tissue from time-domain measurements is presented. The data analysis is based on the evaluation of the first moment and the second centralized moment, i.e., the mean time of flight and the variance of the measured distribution of times of flight (DTOF) of photons injected by short (picosecond) laser pulses. Analytical expressions are derived for calculation of absorption and of reduced scattering coefficients from these moments by application of diffusion theory for infinite and semi-infinite homogeneous media. The proposed method was tested on experimental data obtained with phantoms, and results for absorption and reduced scattering coefficients obtained by the proposed method are compared with those obtained by fitting of the same data with analytical solutions of the diffusion equation. Furthermore, the accuracy of the moment analysis was investigated for a range of integration limits of the DTOF. The moment analysis may serve as a comparatively fast method for evaluating optical properties with sufficient accuracy and can be used, e.g., for on-line monitoring of optical properties of biological tissue.     

Assessment of intakes of mixtures of radionuclides

Australia has several uranium mines and a large number of mineral sand mines, with associated processing facilities. Exposures resulting from these mining and processing operations usually involve intakes of mixtures of radionuclides. This work describes the development of a suite of first order, linear compartment models, based on the ICRP Publication 66 respiratory tract model, and an analytical solution to the decay equations, for assessing the consequences of such intakes. The computer programs based on these models directly compute excretion, organ retention and organ and whole-body doses for intakes of either single radionuclides or any mixture of radionuclides belonging to the same radioactive decay chain. The intake can be via inhalation, ingestion or injection, and can be acute, chronic or of limited duration. The starting concentration and degree of secular (dis)equilibrium can be specified for each radionuclide. No assumptions need to be made about the relative magnitudes of the radioactive half-lives of the different nuclides.     

Estimation of potentialities of methods of summation of direct measurement errors

Conventional methods for summation of direct measurement errors are considered. Conditions under which these methods provide consistent results are stated. It is proposed to utilize for characteristic of the total error, its interval estimator or the half-sum of the value obtained by adding up its arithmetic and geometric random errors.Translated from Izmeritel'naya Tekhnika, No. 4, pp. 10–12, April, 1995.     

空压机轴承箱蜗壳温度探头油封改造

由于空压机进气侧轴承箱蜗壳温度探头密封效果不好,使空压机及其后续管道受到油污染。后将温度探头的O形圈密封改为骨架油封,杜绝了轴承箱漏油问题。文章简介空压机的结构和技术参数,详细介绍了骨架油封的制作和优点。     

Determination of parameters of microstructural inhomogeneity of deformation of metals by the method of modeling

The article suggests a method of evaluating the microstructural inhomogeneity of deformation of metals by modeling. The method includes the measurement of deformations of metal according to meshes of a dividing grid with small base and the calculation of the distribution parameters of microdeformations in model representation. It is shown that the modeling method makes it possible objectively to evaluate the microinhomogeneity of deformation of metals independently of the chosen mesh size of the dividing grid. New structural characteristics are introduced: the base and wave of variation expressing the degree of crumbling or amalgamation of metal grains by inhomogeneity of deformation.Translated from Problemy Prochnosti, No. 7, pp. 40–44, July, 1991.     

Characteristics of mechanical properties of materials in studies of conditions of attainment of marginal states

It is shown that conditions of attainment of marginal states in the material of structural components are formulated on the basis of analysis of force and deformation criteria of formation and development of destruction. The parameters of these criteria are data on types of structural materials, standard and special characteristics of their mechanical properties, structural forms of considered elements of the equipment, and their operating stress loading. In this case, the construction of a system of state equations for describing interrelation of current damage, external actions, and responses to them is based on the concept of calculating variations in properties of materials at all stages of the design life cycle.     

Analysis of anisotropy of properties on the basis of studies of texture of coarse-grained ingots of thermoelectric materials

An analysis of anisotropy of the properties of a Bi₂Se_0.3Te_2.7 solid solution was carried out using construction of demonstrative surfaces for thermoelectric effectiveness and thermal expansion coefficients. It is shown that the texture is an important factor forming anisotropy of properties and technological fitness of ingots for manufacturing modules. Anisotropy of properties based on the studies of the ingot textures obtained using the float-zone method and Bridgman method (growing thermoelectric plates in a flat cavity) was studied.