高分子量聚碳硅烷的合成及其表征

以常压合成的低分子量聚碳硅烷(PCS)为原料,分别在470℃高压及常压下反应一定时间,制备了高分子量PCS先驱体。研究了反应时间对：PCS分子量及其分布、软化点、Si—H键含量及可纺性的影响。研究表明,随着反应时间的延长,PCS低分子量部分逐渐减少,高分子量部分逐渐增加,分子量分布逐渐变宽,从而PCS分子量逐渐增大,软化点逐渐升高,Si—H键含量逐渐降低,可纺性逐渐变差。在相同的反应时间下,高压比常压对PCS分子量的增长更有利。在470℃高压或常压下反应时间2～3h时,可获得分子量高、可纺性良好的PCS先驱体。     

聚二甲基硅烷高温高压合成聚碳硅烷工艺研究

以聚二甲基硅烷(PDMS)为原料,在高压釜内高温高压反应制备了聚碳硅烷(PCS)先驱体,研究了合成条件对反应终压、Si-H键含量、产物产率、软化点、分子量及其分布及可纺性的影响.研究表明,随着反应温度的提高,反应时间的延长,反应终压逐渐增大,产物的分子量与软化点增高,但同时分子量的分散性增大使可纺性变差.当PDMS在高压釜内460℃下反应4～6h,或450℃下反应6～7h时,可以制得软化点约为200～220℃的PCS,其高分子部分含量约 5%～10 %(质量分数),Si-H键含量大于0.9,可纺性较好,适合于制备SiC纤维.     

反应温度对液态聚硅烷高压合成聚碳硅烷性能的影响

以液态聚硅烷(LPS)为原料,在高压釜内反应制备了聚碳硅烷(PCS)先驱体。研究发现,随着反应温度的升高．PCS的分子量增大,产率提高,软化点提高．Si—H键含量降低．在反应过程中LPS首先转化为小分子量的PCS．然后是小分子的PCS间发生脱氢及少量脱甲烷缩合使分子量长大。450℃后,反应产率明显增加,分子量分布出现中分子量峰。     

含铍碳化硅陶瓷先驱体聚铍碳硅烷的合成

以氢氧化铍、硫酸和乙酰丙酮为原料合成了乙酰丙酮铍(Be(acac)2).用乙酰丙酮铍和聚碳硅烷在加热的条件下反应一定时间,生成了树脂状的产物.反应中乙酰丙酮铍被消耗,生成产物熔点相对起始聚碳硅烷熔点升高.元素分析表明产物中含有铍元素,凝胶渗透色谱分析表明产物分子量相对起始聚碳硅烷向增大的方向发生变化.傅立叶红外光谱分析表明产物中主要存在如下结构:Si(CH3)2—CH2—,—Si(CH3)·(H)—CH2—.核磁共振1H-NMR分析表明反应物中Si—H键被消耗.根据分析结果推测了反应机理,Si—H键的消耗在产物的形成中起了重要作用.实验与理论分析表明先驱体产物是一种含铍聚碳硅烷,可以命名为聚铍碳硅烷(PBeCS).在1200℃的高温处理下产物作为先驱体可以转化为碳化硅陶瓷,元素分析表明碳化硅陶瓷中含有铍,是含铍碳化硅陶瓷.     

高压合成聚碳硅烷的分子量分布与可纺性

采用高压合成方法合成了聚碳硅烷（PCS）,研究了高低分子含量、分散系数对PCS软化点、分子量分布及可纺性的影响。结果表明,可以用软化点加分子量分布来判断PCS的熔融可纺性．当PCS的软化点低于200℃,分散系数小于1．8,高、中分子含量比例小于0．1时,可纺性很好;随着分子量的增大,软化点的升高,高分子含量增加,分子量分布宽化,可纺性开始变差,当软化点大于260℃,分散系数大于2．2,高、中分子含量比例大于0,3时,可纺性很差,甚至失去可纺性。要得到软化点高、分散系数低、可纺性好的PCS,必须控制PCS的高、中分子含量比例约为0．1～0．3,低、中分子含量比例约0．8左右,分散系数约为1．8～2．2。     

聚碳硅烷纤维在环己烯气氛中的不熔化处理

将聚碳硅烷(PCS)纤维在环己烯气氛中进行化学气相交联不熔化处理,其氧含量比空气不熔化处理大大降低,组成和结构也发生了变化,气体副产物中存在环己烷和小分子硅烷.在环己烯气氛中,随着温度的升高,PCS分子的Si-H键的反应程度逐渐提高,纤维的凝胶含量逐渐增大.环己烯受热引发PCS分子中的Si-H和Si-CH3键断裂生成Si自由基和Si-CH2自由基,促进PCS分子间形成Si-CH2-Si交联结构;同时,环己烷作为侧基引入到PCS分子结构中,使纤维的碳含量随之增高.随着反应温度的升高,部分环己烷侧基和少量小分子硅烷会从PCS分子主链脱出.     

SiC陶瓷纤维先驱体——聚铝碳硅烷的合成与表征

在高温常压下,以聚二甲基硅烷(Polydimethylsilane,PDMS)和乙酰丙酮铝(Al(AcAc)3)为原料,合成了碳化硅(SiC)陶瓷纤维先驱体———聚铝碳硅烷(Polyaluminocarbosilane,PACS)。采用红外光谱法和凝胶渗透色谱法对制备的PACS进行了结构和分子量表征;通过正交实验设计,研究了反应温度、裂解温度、反应时间和原料配比4种因素对PACS的Si-H键含量、支化度和数均分子量Mn的影响,并用极差分析法进行了主次因素分析,结果表明反应温度是上述三指标的主要影响因素。综合分析各指标对PACS后续纺丝性能和高温碳化过程的影响,确定制备PACS较优的实验条件为:反应温度390℃、裂解温度490℃、反应时间10h及原料Al(AcAc)3与PDMS配比4%(质量分数)。     

含硼聚碳硅烷的制备及热解行为EI北大核心CSCD

为制备陶瓷产率高、高温性能优良的碳化硅(SiC)陶瓷先驱体,利用频那醇硼烷(PINB)与聚碳硅烷(PCS)的脱氢偶合反应,对聚碳硅烷进行化学改性。改变PINB与PCS的质量比(1∶20、1∶10、1∶5),制备了一系列不同硼(B)含量的含硼聚碳硅烷(PBCS)。通过傅里叶变换红外光谱分析、核磁共振氢谱分析、热重分析以及X射线衍射分析等手段研究了PBCS的组成、结构及热解行为。结果表明,通过B-H键的反应将B元素以PINB骨架形式引入PCS结构;引入B元素可以将PCS的陶瓷产率从78%提高至92%;另外,B元素的引入引起PCS的交联,PBCS的热解过程分3个阶段。同时B元素的引入抑制了SiC晶体的生长,将材料的耐温性能提高至1400℃。     

固/液态聚碳硅烷共混制备碳化硅纤维的研究

以超支化液态聚碳硅烷(LPCS)与固态聚碳硅烷(纯PCS)的共混物作先驱体,熔融纺丝;所得原丝再在热空气气氛中氧化交联,在高温氮气气氛中热裂解,得到碳化硅纤维。研究表明,15%(质量分数)LPCS的加入,可使纯PCS先驱体的纺丝温度,从285℃降低到225℃;纺丝性能和纤维表面质量明显提高;还可以提高氧化交联的效率,降低交联温度,从而减少纤维部分融并、粘结的弊端;虽然纤维的室温力学强度有所降低,但抗氧化性能提高,1400℃氧化交联后,力学性能几乎不变;而纯PCS的力学性能却降为原来的50%。     

含铍聚碳硅烷的合成机理研究

含铍SiC陶瓷纤维是一种新型的高性能SiC纤维,而优质含铍聚碳硅烷先驱体(PBCS)的合成是得到该种纤维的重要保证。以乙酰丙酮铍(Be(acac)_2)和聚碳硅烷(PCS)为原料制备得到PBCS,并对其合成机理进行了深入研究,采用PCS和石蜡分别与Be(acac)2进行对比反应,用GC-MS对反应小分子产物进行分析,确定了Be(acac)_2与PCS的成键反应实际是Be与Si—H键反应,C—H键没有参与含铍键的形成反应;根据小分子反应产物的生成途径,合理分析了PBCS的合成反应原理。     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Study on Bond Ability of Arc-Spraying Coatings with Different Surface Pretreatment on Cast-Iron

Arc spraying coatings are widely used in various applications, but uncommon in cast iron substrate. Different surface pretreatment technology is tested on substrates of gray cast iron. Surface roughness and residual stress were measured by TR200 and X-ray diffraction analyzer. Influence of different surface pretreatment methods ( dry blasting and fusebond) on roughness and residual stress was analyzed. The arc-sprayed coatings of wire 3Cr13 (φ2mm) on gray cast iron substrate is studied. The microstructure and interface of bonding layer were observed by SEM. The bond strength was taken by tensile test. Results show that bond strength with grit blasting is higher than fuse-bond; it is feasible to make wire 3Cr13 coating with arc spraying on cast iron substrate roughened by grit blasting.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Evaluation of fatigue life of steel using steel grain size

The insightful discussion of the relationship between the construction of metallographic and fatigue life and proposition of mathematical relationships describing this relationship was conducted in the paper. This paper presents a method for estimating the fatigue life, based on the construction of the microstructural material taking into account the grain size and the participation of ferrite and pearlite phase.